Appendix A Messages

SDLC Link Startup Error Messages

SDLC Link Driver Error Messages

SNACONTROL Error Messages

SNA Transport Error Messages

SNA Transport Logging Messages

SDLC Link Shutdown Error Messages

X.25 Link Failure Error Codes

X.25 Link Module Configurator Error Codes

X.25 Link QLLC Internal Error Codes

NetView Alerts Error Messages

Network Dump Manager Error Messages

LAN Error Messages

• SDLC link startup error messages: These are messages that can occur when you start the SDLC link. These messages occur when the SNACONTROL START command calls the WAN_Module_Config procedure and encounters an error. They are logged in this format:

  
   Linkname        = LinkName      Event Type   = EventType
   Log Class       = LogClass      Path         = Path
   Error Num       = ErrorNumber   Status       = Status
  
  

• SDLC link driver error messages: These are messages that are generated when errors are encountered by the SDLC link driver. They are logged in this format:

  
   Linkname        = LinkName      Event Type   = EventType
   Log Class       = LogClass      Location     = Location
   Sublocation     = Sublocation   Error Code   = ErrorCode
   State           = State         Cause Status = CauseStatus
   Error Actions   = ErrorActions
  
  

• SNACONTROL error messages: These are error messages generated by SNACONTROL commands. Each message has this suffix:

  SNACIERR

• SNA Transport error messages: These are run-time error messages that can occur when SNA Transport intrinsics are used. Each message has this suffix:

  SNAERR

• SNA Transport logging messages: These are messages that are logged for SNA Transport.

• SDLC link shutdown error messages: These are messages that can occur when you stop the SDLC link. These messages occur when the SNACONTROL STOP command calls the WAN_Kill_Module procedure and encounters an error. They are logged in this format:

  
   Linkname        = LinkName       Event Type   = EventType
   Log Class       = LogClass       Path         = Path
   Error Num       = ErrorNumber    Status       = Status
  
  

• X.25 link failure error codes: These are codes that are generated for X.25 link failures by the Qualified Logical Link Control (QLLC) module. They are applicable based on the ErrorNum displayed as part of these SNA Transport logging messages:

  
   Link connect failure on node NodeName
   subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
  
   Link failure, recovery in progress on node NodeName
   subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
  
   Link failure, shutting down the node NodeName
   subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
  
  

• X.25 link module configurator error codes: These are codes that are generated by the X.25 link module configurator. They are applicable based on the ErrorCode displayed as part of these SNA Transport logging messages:

  
   Attempt to close link failed on node NodeName
   Subsystem = 734, Error Code = ErrorCode
  
   Attempt to open link failed on node NodeName
   Subsystem = 734, Error Code = ErrorCode
  
  

• X.25 link QLLC internal error codes: These are codes that are generated by the X.25 link Qualified Logical Link Control (QLLC) module when a QLLC internal error occurs. They are applicable based on the ProcNum displayed as part of these SNA Transport logging messages:

  
   Link connect failure on node NodeName
   subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
  
   Link failure, recovery in progress on node NodeName
   subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
  
   Link failure, shutting down the node NodeName
   subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
  
  

• NetView alerts error messages: These are the error messages that can occur when an operator-generated NetView alert is sent.

• Network Dump Manager error messages: These are error messages that are generated when errors occur while the SDLC link is being dumped. Each message has this prefix:

  **** DUMP ERROR

• Token Ring LAN error messages: These are messages generated by the Token Ring Driver or Token Ring Card. Messages have the following format:

  Internal driver error in SYSLINK (LANWARN ####) or (LANERR ####)

  where #### is an error number.