Listed below are the error codes that are generated by the X.25 link module
configurator. These messages are displayed on the HP e3000 operator's console.
They are listed here in numerical order according to the
ErrorCode displayed as part of these SNA Transport logging
messages:
Attempt to close link failed on node NodeName
Subsystem = 734, Error Code = ErrorCode
Attempt to open link failed on node NodeName
Subsystem = 734, Error Code = ErrorCode
The logging messages are described in "SNA Transport Logging Messages" earlier
in this appendix.
MESSAGE: CONFIG OPEN ERROR
Level: -200
CAUSE: The module configurator encountered an error while
trying to open the configuration file.
ACTION: Verify that the NMCONFIG.PUB.SYS configuration
file exists.
MESSAGE: CONFIG RETRIEVAL ERROR
Level: -201
CAUSE: The module configurator encountered an error while
retrieving the SNA/X.25 link configuration information for the current
SNA node.
ACTION: Verify that the correct version of NMMGR is installed
on the system, and that an X.25 link is configured for the SNA node
being started.
MESSAGE: PROCESS CREATION ERROR
Level: -202
CAUSE: The module configurator was unable to launch the
Qualified Logical Link Control (QLLC) module.
ACTION: Verify that the file containing the QLLC module
(SNAX25.PUB.SYS) exists.
MESSAGE: TRACE OPEN ERROR
Level: -203
CAUSE: The module configurator was unable to open the trace file.
ACTION: Issue the SNACONTROL START command with the trace
file name specified for the LINKTRACE parameter. If the
error still occurs, issue the SNACONTROL START command
without specifying a trace file name (that is, let the
default file name be used). If the error still occurs, call your
Hewlett-Packard support contact.
MESSAGE: STATUS BUFFER INVALID
Level: -204
CAUSE: The Qualified Logical Link Control (QLLC) module
returned an invalid buffer containing the link status information.
Note that the node can still function, but link status information
cannot be retrieved.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: STATUS REPLY INVALID
Level: -205
CAUSE: The module configurator status routine received
an invalid status reply. Note that the node can still function,
but link status information cannot be retrieved.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO RECEIVE OPENLINK COMPLETION MESSAGE
Level: -500
CAUSE: The module configurator encountered an error while
trying to receive the OpenLink completion message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO GET MSG FRAME FOR CLOSELINK REQUEST
Level: -501
CAUSE: The module configurator encountered an error while
trying to allocate the CloseLink request message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO SEND CLOSELINK REQUEST
Level: -502
CAUSE: The module configurator encountered an error while
trying to send the CloseLink request message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO RECEIVE CLOSELINK COMPLETION MESSAGE
Level: -503
CAUSE: The module configurator encountered an error while
trying to receive the CloseLink completion message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO GET MSG FRAME FOR TRACE ENABLE REQUEST
Level: -504
CAUSE: The module configurator encountered an error while
trying to allocate the trace enable request message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO SEND TRACE ENABLE REQUEST
Level: -505
CAUSE: The module configurator encountered an error while
trying to send the trace enable request message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO SEND TRACE DISABLE REQUEST
Level: -506
CAUSE: The module configurator encountered an error while
trying to send the trace disable request message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO GET MESSAGE FRAME FOR TRACE DISABLE REQUEST
Level: -507
CAUSE: The module configurator encountered an error while
trying to allocate the trace disable request message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO GET MESSAGE FRAME FOR STATUS REQUEST
Level: -508
CAUSE: The module configurator encountered an error while
trying to allocate the status request message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO SEND STATUS REQUEST
Level: -509
CAUSE: The module configurator encountered an error while
trying to send the status request message.
ACTION: Call your Hewlett-Packard support contact.
MESSAGE: UNABLE TO RECEIVE STATUS COMPLETION MESSAGE
Level: -510
CAUSE: The module configurator encountered an error while
trying to receive the status completion message.
ACTION: Call your Hewlett-Packard support contact.