|
|
Listed below are the error messages that can occur when SNA Transport
intrinsics are being used. They are listed in numerical order according
to message number. SNA Transport, itself, does not display these
messages: It returns the error number to the SNA service using the
intrinsics, and the service can optionally display the message. These
messages are not logged; they are written to $STDLIST by the SNA
service only.
MESSAGE: Invalid session. (SNAERR 2) A call was made to an SNA
Transport intrinsic with a bad session number. |
Level: SNAERR 2
CAUSE: An invalid session number was specified in a call
to an SNA Transport intrinsic.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Missing Completer Parameter. (SNAERR 3) An SNA Transport
completion occurred with a missing parameter. |
Level: SNAERR 3
CAUSE: The SNA completer was activated with an invalid
Cstation, Xfercount, or
TargetFlag parameter.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Parameter bounds violation. (SNAERR 5) An out-of-bounds
parameter was passed to an SNA Transport intrinsic. |
Level: SNAERR 5
CAUSE: An SNA service passed an out-of-bounds parameter
to an SNA Transport intrinsic.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Invalid flag parameter. (SNAERR 6) An invalid flag parameter
was passed to an SNA Transport intrinsic. |
Level: SNAERR 6
CAUSE: The Flag parameter passed to the
SNARcv or SNAPreview intrinsic was invalid.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Session is active. (SNAERR 7) The LU-SSCP session for this NAU
is active. |
Level: SNAERR 7
CAUSE: The NAU's LU-SSCP session is active.
ACTION: None. |
MESSAGE: No available AFT entry. (SNAERR 9) No room left in current
stack segment for another AFT. |
Level: SNAERR 9
CAUSE: An SNAOpenUser was attempted, but no room for
another Available File Table (AFT) entry is available in the current
stack segment.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Bad PI in RH. (SNAERR 10) The Pacing indicator was set in the
RH sent to SNA Transport. |
Level: SNAERR 10
CAUSE: The pacing indicator (PI) was set in the Request/Response
Header (RH) passed to one of the SNA Send intrinsics.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Bad BCI in RH. (SNAERR 11) An improper chaining sequence
occurred. |
Level: SNAERR 11
CAUSE: The Begin Chain Indicator (BCI) was not set in the Response
Header (RH) passed to one of the SNA Send intrinsics when sending
a response.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Bad ECI in RH. (SNAERR 12) An improper chaining sequence occurred. |
Level: SNAERR 12
CAUSE: The End Chain Indicator (ECI) was not set in the Response
Header (RH) passed to one of the SNA Send intrinsics when sending
a response.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Bad EDI in RH. (SNAERR 13) Attempt was made to send enciphered data. |
Level: SNAERR 13
CAUSE: The Enciphered Data Indicator (EDI) was set in the Request
Header (RH) passed to one of the SNA Send intrinsics when sending
a request.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Reserved bits in RH must be set to zero. (SNAERR 14 |
Level: SNAERR 14
CAUSE: Various reserved bits in the Request/Response
Header (RH) were incorrectly set by the calling SNA service when
making a call to the SNA Send intrinsics.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Internal Error. (SNAERR 15) An SNA Transport Internal
Error occurred. |
Level: SNAERR 15
CAUSE: A serious error occurred in SNA Transport.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Invalid RU size. (SNAERR 16) An attempt was made to send an RU
longer than the Max RU size. |
Level: SNAERR 16
CAUSE: A call to the SNA Send intrinsics, specifying a
buffer length larger than the one specified in the Half Session Control
Block (HSCB) for that session, was made.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: NAU is inactive. (SNAERR 17) The LU-SSCP session for this NAU
is inactive. |
Level: SNAERR 17
CAUSE: A call to the SNAOpenUser intrinsic to open an
LU-LU session was made, and the corresponding LU-SSCP session is not yet
active.
ACTION: Ensure that the LU-SSCP session has been activated on the
remote system. If it has not been activated, activate it and try again. |
MESSAGE: Invalid Plabel. (SNAERR 18) An Invalid plabel was passed to
the SNAControl intrinsic. |
Level: SNAERR 18
CAUSE: A call to the SNAControl intrinsic (with
FunctionCode = 1) passed a bad Plabel for the
software interrupt procedure.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: LU-SSCP message pending. (SNAERR 19) |
Level: SNAERR 19
CAUSE: A message on the LU-SSCP session is pending and
must be completed before a Send can be issued.
ACTION: A call to the SNARcv or SNARcvfromSSCP
intrinsic must be made before any calls to the
SNA Send intrinsics are made. |
MESSAGE: RU buffer too small. (SNAERR 20) An RU received was larger
than the buffer provided. |
Level: SNAERR 20
CAUSE: An SNA Receive completed, but the Request/Response
Unit (RU) received was larger than the buffer provided in the call to the
SNARcv, SNAPreview, or SNARcvfromSSCP intrinsic.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Invalid LU name. (SNAERR 21) The LU name specified does
not exist. |
Level: SNAERR 21
CAUSE: A call to the SNAOpenUser intrinsic to open an
LU-LU session was made, but the LU name specified in the call is not
configured for this node.
ACTION: Use NMMGR or the configuration file critical summary
to check for the valid LUs configured for the requested node. |
MESSAGE: Invalid session type. (SNAERR 22) An attempt was made to open
a non LU-LU session. |
Level: SNAERR 22
CAUSE: An invalid session type parameter was specified
in a call to the SNAOpenUser intrinsic to open a session.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Negative LU-SSCP response. (SNAERR 23) A negative response was
sent by the host in response to a request. |
Level: SNAERR 23
CAUSE: An SNA service received a negative response as
a result of a call to the SNASendtoSSCP intrinsic.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Invalid configuration access. (SNAERR 24) SNA Transport was
unable to access the required configuration data. |
Level: SNAERR 24
CAUSE: A call to the NMConfgetdata intrinsic failed for
some reason.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Request pending. (SNAERR 25) An SNA Transport Receive request
is already pending. |
Level: SNAERR 25
CAUSE: A call to an SNARcv intrinsic was made while a
current request is outstanding.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: No available NAU. (SNAERR 26) All LUs specified in the
SNAOPENUSER are currently in use. |
Level: SNAERR 26
CAUSE: The specified LUs are all in use.
ACTION: Try again later when the system is less busy,
or try using another group of LUs. |
MESSAGE: IO pending. (SNAERR 27) |
Level: SNAERR 27
CAUSE: A call to the SNAClose or SNAControl
intrinsic was made while a send or receive is pending.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Invalid function code. (SNAERR 28) |
Level: SNAERR 28
CAUSE: An SNA service passed a bad function code to the
SNAControl or SNASessinfo intrinsic.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Inactive node or invalid node name. (SNAERR 29) |
Level: SNAERR 29
CAUSE: An invalid node name was specified in a call to
the SNAOpenUser intrinsic.
ACTION: Ensure that the specified node is a valid SNA
node that is currently active. |
MESSAGE: Illegal call. (SNAERR 30) An attempt was made to access an
LU-SSCP session in an LU-LU session. |
Level: SNAERR 30
CAUSE: A call to the SNASendtoSSCP or
SNARcvfromSSCP intrinsic was made on an LU-LU session.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Invalid error code. (SNAERR 31) |
Level: SNAERR 31
CAUSE: An invalid error code was passed to the SNAErrmsg
intrinsic.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Privilege mode required. (SNAERR 32) |
Level: SNAERR 32
CAUSE: An attempt to call an SNA Transport intrinsic
was made while in user mode.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Invalid InfoWanted parameter. (SNAERR 33) |
Level: SNAERR 33
CAUSE: An invalid InfoWanted parameter was
specified in a call to the SNASessinfo intrinsic.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: No request pending. (SNAERR 35) |
Level: SNAERR 35
CAUSE: An attempt to abort an SNARcv,
SNARcvFromSSCP, or SNASendtoSSCP intrinsic was made when
no such request was outstanding.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Link shutdown occurred. (SNAERR 36) |
Level: SNAERR 36
CAUSE: A link shutdown has been requested with the
SNACONTROL STOP command, and all sessions are being notified.
ACTION: Wait until the link has been restarted and then
continue. |
MESSAGE: Protocol shutdown requested. (SNAERR 37) |
Level: SNAERR 37
CAUSE: A protocol shutdown has been requested with the
SNACONTROL STOP command, and all sessions are being notified.
ACTION: Wait until the link has been restarted and then continue.
CAUSE: A protocol shutdown has been requested with the
SNACONTROL STOPSESS command, and the session it was requested for
is being notified.
ACTION: None. |
MESSAGE: Quiesce shutdown requested. (SNAERR 38) |
Level: SNAERR 38
CAUSE: A quiesce shutdown has been requested with the
SNACONTROL STOP command. New sessions will not be started, and all
current active sessions are to complete their current activities and close
in an orderly fashion.
ACTION: Wait until the link has been restarted and then continue.
CAUSE: A quiesce shutdown has been requested with the
SNACONTROL STOPSESS command, and the session it was requested for is
being closed in an orderly fashion.
ACTION: None. |
MESSAGE: CATSNA.PUB.SYS access error. (SNAERR 39) SNA Transport was
unable to access its catalog file. |
Level: SNAERR 39
CAUSE: The SNA Transport message catalog file
(CATSNA.PUB.SYS) is missing, invalid, or locked by another process.
ACTION: Replace the catalog file with a valid SNA catalog
file. |
MESSAGE: Out of Stack Space. (SNAERR 40) |
Level: SNAERR 40
CAUSE: A call was made to an SNA Transport intrinsic without
enough stack space available or with the data segment frozen in memory.
ACTION: Write down the circumstances and call your
Hewlett-Packard support contact. |
MESSAGE: Invalid data offset. (SNAERR 48) |
Level: SNAERR 48
CAUSE: An invalid offset into the given data segment
was specified in a call to an SNA Transport intrinsic.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Link Failure occurred. (SNAERR 51) |
Level: SNAERR 51
CAUSE: A link failure has occurred, and all sessions are being notified.
ACTION: Wait until the node has been reactivated and then
try again. |
MESSAGE: SNA Transport Internal Error Shutdown. (SNAERR 52) |
Level: SNAERR 52
CAUSE: An SNA Transport internal error has occurred,
and all sessions are being notified.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Bad Maxinfo length parameter. (SNAERR 55) |
Level: SNAERR 55
CAUSE: An invalid MaxInfolgth parameter was
specified in a call to the SNASessinfo intrinsic.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Error msg truncated because buffer was too small. (SNAERR 58) |
Level: SNAERR 58
CAUSE: A buffer too small to hold the error message from the SNA
Transport message catalog file (CATSNA.PUB.SYS) was passed in a
call to the HPSNAErrmsg or SNAErrmsg intrinsic. The
message was truncated to fit into the buffer that was passed.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Expedited response pending. (SNAERR 100) |
Level: SNAERR 100
CAUSE: An attempt to send an expedited request was made
while in a state that does not allow it.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Data traffic inactive. (SNAERR 101) |
Level: SNAERR 101
CAUSE: An attempt to send a request was made before a
Start Data Traffic (SDT) has been received or the positive response
has been sent.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: SDT request not received. (SNAERR 102) |
Level: SNAERR 102
CAUSE: A response to a Start Data Traffic (SDT) is being
sent, but no SDT was received from the remote system.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Invalid session control protocol. (SNAERR 103) |
Level: SNAERR 103
CAUSE: An invalid sequence of session control events has occurred.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: RQR request pending. (SNAERR 104) |
Level: SNAERR 104
CAUSE: An attempt to send a ReQuest Recovery (RQR) request
was made while in a state other than reset.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: STSN request not pending. (SNAERR 105) |
Level: SNAERR 105
CAUSE: A response to a Set and Test Sequence Numbers
(STSN) request is being sent, but no corresponding STSN request
has been received.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Unsupported CRV request/response. (SNAERR 107) |
Level: SNAERR 107
CAUSE: An attempt to send a CRyptography Verification
(CRV) request or response was made.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Unsupported session control request. (SNAERR 108) |
Level: SNAERR 108
CAUSE: An attempt to send an unsupported Session Control
(SC) request was made.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Unsupported session control response. (SNAERR 109) |
Level: SNAERR 109
CAUSE: An attempt to send an unsupported Session Control
(SC) response was made.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: No such deactivation request (UNBIND,DACTLU,DACTPU) received.
(SNAERR 110) |
Level: SNAERR 110
CAUSE: An SNA service is trying to send a response to
a deactivation request (UNBIND, DACTLU, or DACTPU), but no such
deactivation request has been received.
ACTION: The SNA service should examine the situations
in which a deactivation response is sent, and verify that a response
is sent only after a deactivation request has been received. |
MESSAGE: No such activation request (BIND,ACTLU,ACTPU) received.
(SNAERR 111) |
Level: SNAERR 111
CAUSE: An SNA service is trying to send a response to
an activation request (BIND, ACTLU, or ACTPU), but no such activation
request has been received.
ACTION: The SNA service should examine the situations
in which an activation response is sent, and verify that a response
is sent only after an activation request has been received. |
MESSAGE: The target parameter passed to iowait is too small.
(SNAERR 112) |
Level: SNAERR 112
CAUSE: A target parameter passed in a call to the
IOWait intrinsic is too small to receive sense data.
The size of the target parameter is checked only when a non-waited
call to the SNASendToSSCP intrinsic completes.
ACTION: Ensure that the size of the target parameter (the
second parameter) that was passed to the IOWait intrinsic is at
least 4 bytes. |
MESSAGE: An error occurred during a switch from CM to NM.
(SNAERR 113) |
Level: SNAERR 113
CAUSE: When changing from compatibility mode (CM) to
native mode (NM), an error occurred when an SNA compatibility mode
intrinsic was called.
ACTION: Write down the circumstances and call your Hewlett-Packard
support contact. |
MESSAGE: Couldn't send BIND on a Secondary LU. (SNAERR 115) |
Level: SNAERR 115
CAUSE: When SNAOpenUser was called to open an LU, the LU
was opened as a secondary LU. A secondary LU is not capable of issuing a
BIND. However, a call was made to SNASendExpedited, to send a BIND.
So, an error occurred.
ACTION: Modify the user program that is calling
SNASendExpedited. |
MESSAGE: A waited send intrinsic call was aborted by SNA Transport to
avoid a deadlock. (SNAERR 116) |
Level: SNAERR 116
CAUSE: When user data is sent to the remote system, if
the pacing window is not open SNA Transport must place the request
in its queue. If, at the same time, the remote system sends an expedited
request (which is not affected by the pacing window), SNA Transport
could hang. To avoid being hung, SNA Transport aborts the previous
waited send call and generates this message to warn the user.
ACTION: The user program should handle this situation. |
|