HP 3000 Manuals HP 3000 Manuals
Probe Logging Location Codes
7 CLAS0001 Cause: Bad or unexpected message received by PROBE
Port (PARM = Message Function Code).
Action: See "Submitting an SR" in appendix A of this
manual.
14 CLAS0003 Cause: Retransmission timeout is faster than packet
can be sent out to the node. This can happen if the
node is congested. PARM indicates probe (%1) or proxy
(%2) timer.
Action: Increase the retransmission time in the
configuration file
(@NETXPORT.NI.lanNI.protocol.PROBE). See "Submitting
an SR" in appendix A of this manual.
15 CLAS0003 Cause: Reply received after request has timed out
(PARM = Sequence number from PROBE Address Reply
Packet).
Action: Can happen from time to time. If excessive,
then increase retransmission timeout or retry count in
Probe Protocol Configuration screen in NMMGR and see
"Submitting an SR" in appendix A of this manual.
16 CLAS0003 Cause: Reply received after request has timed out
(PARM = Sequence number from PROBE Name Reply Packet).
Action: Can happen from time to time. If excessive,
then increase retransmission timeout or retry count in
the Probe Protocol Configuration screen and see
"Submitting an SR" in appendix A of this manual.
17 CLAS0002 Cause: DictSend to name server port failed on Proxy
Name Request (PARM = DictSend result code).
Action: See "Submitting an SR" in appendix A of this
manual.
20 CLAS0002 Cause: Reply received after request has timed out
(PARM = Request ID).
Action: Can happen from time to time. If excessive,
then increase retransmission timeout or retry count in
the Probe Protocol Configuration screen and see
"Submitting an SR" in appendix A of this manual.
21 CLAS0002 Cause: Room allocated for node name and path report
is too small (PARM = number of bytes short).
Action: See "Submitting an SR" in appendix A of this
manual.
22 CLAS0002 Cause: Timer popped which has no request outstanding
(PARM = Time request ID).
Action: See "Submitting an SR" in appendix A of this
manual.
23 CLAS0002 Cause: Received Gateway Reply message, which is not
supported (PARM = Probe message type).
Action: See "Submitting an SR" in appendix A of this
manual.
24 CLAS0003 Cause: Late reply came in when cleaning up Proxy
(PARM = request ID).
Action: See "Submitting an SR" in appendix A of this
manual.
27 CLAS0002 Cause: Message type in incoming packet is invalid.
Action: See "Submitting an SR" in appendix A of this
manual.
28 CLAS0005 Cause: Retransmission has occurred (PARM = Retries
until exhausted).
Action: Informative message.
29 CLAS0002 Cause: Attempt to cache node name failed (PARM =
Length of Name).
Action: See "Submitting an SR" in appendix A of this
manual.
30 CLAS0002 Cause: Attempt to cache node name failed (PARM =
Length of Name).
Action: See "Submitting an SR" in appendix A of this
manual.
32 CLAS0002 Cause: Attempt to map addresses failed (PARM = Path
resolve error code).
Action: Increase the Maximum Number of Nodes in the
LAN 802.3 Network Interface screen in NMMGR. If error
recurs then see "Submitting an SR" in appendix A of
this manual.
33 CLAS0002 Cause: Attempt to map addresses failed (PARM = Path
resolve error code).
Action: See "Submitting an SR" in appendix A of this
manual.
35 CLAS0004 Cause: PROBE Protocol Started.
Action: Informative message.
36 CLAS0004 Cause: PROBE Protocol Stopped.
Action: Informative message.
37 CLAS0004 Cause: PROBE Protocol Stopped (Delayed with Proxy).
Action: None.
38 CLAS0005 Cause: Probe Unsolicited Request made (PARM =
Sequence number allocated for request).
Action: Informative message.
39 CLAS0005 Cause: Probe Name Request made (PARM = Sequence
number allocated for request).
Action: Informative message.
40 CLAS0005 Cause: Probe Address Request made (PARM = Sequence
number allocated for request).
Action: Informative message.
46 CLAS0005 Cause: Probe Node Down Request made (PARM = Sequence
number allocated from request).
Action: None.
47 CLAS0002 Cause: Error in trying to delete node name from path
cache after receiving a Probe Node Down message.
Action: See "Submitting an SR" in appendix A of this
manual.
48 CLAS0002 Cause: Attempt to add PROBE to the mapping table
during INIT message failed (PARM = mapping error
code).
Action: See "Submitting an SR" in appendix A of this
manual.
49 CLAS0002 Cause: Could not delete the PROBE entity from the
mapping table in a terminate sequence (PARM = mapping
error code).
Action: See "Submitting an SR" in appendix A of this
manual.
52 CLAS0002 Cause: Invalid device information in Probe's data
area.
Action: See "Submitting an SR" in appendix A of this
manual.
53 CLAS0002 Cause: Invalid device information in Probe's data
area.
Action: See "Submitting an SR" in appendix A of this
manual.
55 CLAS0002 Cause: Attempt to add MAP address failed.
Action: Increase the maximum number of nodes in the
LAN 802.3 NI screen in NMMGR. If error recurs, then
see "Submitting an SR" in appendix A of this manual.