HP 3000 Manuals HP 3000 Manuals
L2Resolve Logging Location Codes
L2Resolve is part of the process between NS Transport and SNA Transport
which provides NS over SNA/XL functionality.
1 Log Class 2 Cause: Unable to send connect request.
Action: See "Submitting an SR" in appendix A of
this manual.
2 Log Class 2 Cause: Unable to send disconnect request.
Action: See "Submitting an SR" in appendix A of
this manual.
3 Log Class 2 Cause: Unable to send verify path message to
NetCP.
Action: See "Submitting an SR" in appendix A of
this manual.
4 Log Class 2 Cause: Unable to send disconnect device message
to NetCP.
Action: See "Submitting an SR" in appendix A of
this manual.
7 Log Class 2 Cause: Control Block data structure cannot be
freed on a reset connection.
Action: See "Submitting an SR" in appendix A of
this manual.
9 Log Class 2 Cause: Connect reply not completed because MAP
entry cannot be added.
Action: See "Submitting an SR" in appendix A of
this manual.
10 Log Class 2 Cause: Unable to update MAP table for rejection
of connection request.
Action: See "Submitting an SR" in appendix A of
this manual.
12 Log Class 2 Cause: Unable to send connect request.
Action: See "Submitting an SR" in appendix A of
this manual.
14 Log Class 2 Cause: Unable to update MAP table for a
connection reset.
Action: See "Submitting an SR" in appendix A of
this manual.
15 Log Class 3 Cause: A connection request has been rejected.
Action: Informative message. The network has
been shut down, or a connection request has been
refused by the other end.
17 Log Class 2 Cause: Invalid request from upper layers in
current state.
Action: See "Submitting an SR" in appendix A of
this manual.
18 Log Class 2 Cause: Invalid request from lower layers in
current state.
Action: See "Submitting an SR" in appendix A of
this manual.
19 Log Class 3 Cause: Reject of an incoming connection request
because maximum number of connections active.
Action: A maximum of 64 connections is allowed.
Retry connection after one has been closed.
21 Log Class 3 Cause: Connect event message before L2Resolve
is fully operational.
Action: Wait for L2Resolve to finish
initialization and try the connection again. If
the problem persists, see "Submitting an SR" in
appendix A of this manual.
22 Log Class 2 Cause: Incoming connect reply before L2Resolve
is fully operational.
Action: Wait for L2Resolve to finish
initialization and try the connection again. If
the problem persists, see "Submitting an SR" in
appendix A of this manual.
23 Log Class 2 Cause: Incoming disconnect reply; maximum
connections exceeded.
Action: A maximum of 64 connections is allowed.
Wait until one connection is closed and try
again. If the problem persists, see "Submitting
an SR" in appendix A of this manual.
24 Log Class 2 Cause: Incoming disconnect reply before
L2Resolve is fully operational.
Action: Wait for L2Resolve to finish
intialization and try the connection again. If
the problem persists, see "Submitting an SR" in
appendix A of this manual.
25 Log Class 2 Cause: Incoming disconnect before L2Resolve is
fully operational.
Action: Wait for L2Resolve to finish
intialization and try the connection again. If
the problem persists, see "Submitting an SR" in
appendix A of this manual.
26 Log Class 2 Cause: Unknown event before L2Resolve is fully
operational.
Action: See "Submitting an SR" in appendix A of
this manual.
27 Log Class 3 Cause: Outbound connect request would exceed
maximum number of connections.
Action: A maximum of 64 connections is allowed.
Wait until a connection is closed and try again.
28 Log Class 2 Cause: Connect reply received for an unknown
connection.
Action: See "Submitting an SR" in appendix A of
this manual.
29 Log Class 2 Cause: Disconnect reply message when maximum
number of connections exceeded.
Action: See "Submitting an SR" in appendix A of
this manual.
30 Log Class 2 Cause: Disconnect reply received for an unknown
connection.
Action: See "Submitting an SR" in appendix A of
this manual.
31 Log Class 2 Cause: Disconnect request received for an
unknown connection.
Action: See "Submitting an SR" in appendix A of
this manual.
32 Log Class 2 Cause: Invalid connect/disconnect message.
Action: See "Submitting an SR" in appendix A of
this manual.
33 Log Class 3 Cause: Outbound connection request during
network shutdown.
Action: Informative message. The network must
be started for successful connection.
34 Log Class 2 Cause: Connection reply for an unknown
connection.
Action: See "Submitting an SR" in appendix A of
this manual.
35 Log Class 2 Cause: Disconnect reply for an unknown
connection and maximum number of connections
exceeded.
Action: See "Submitting an SR" in appendix A of
this manual.
36 Log Class 2 Cause: Disconnect reply message received for an
unknown connection.
Action: See "Submitting an SR" in appendix A of
this manual.
37 Log Class 2 Cause: Disconnect request received for an
unknown connection.
Action: See "Submitting an SR" in appendix A of
this manual.
38 Log Class 2 Cause: Unknown connect/disconnect message
during shutdown.
Action: See "Submitting an SR" in appendix A of
this manual.
39 Log Class 2 Cause: L2Resolve is terminating with
outstanding requests.
Action: See "Submitting an SR" in appendix A of
this manual.
40 Log Class 2 Cause: Connection is active while L2Resolve is
terminating.
Action: See "Submitting an SR" in appendix A of
this manual.
42 Log Class 4 Cause: L2Resolve is terminating.
Action: Informative message.
43 Log Class 2 Cause: L2Resolve deletion from MAP is
unsuccessful during a device disconnect.
Action: See "Submitting an SR" in appendix A of
this manual.
44 Log Class 2 Cause: L2Resolve cannot be bound into MAP
table.
Action: See "Submitting an SR" in appendix A of
this manual.
45 Log Class 4 Cause: L2Resolve is starting.
Action: Informative message.
46 Log Class 2 Cause: Invalid message type for current
L2Resolve state.
Action: See "Submitting an SR" in appendix A of
this manual.
47 Log Class 2 Cause: Error in starting or stopping L2Resolve.
Action: See "Submitting an SR" in appendix A of
this manual.
48 Log Class 2 Cause: Invalid message type received by
L2Resolve.
Action: See "Submitting an SR" in appendix A of
this manual.