HP 3000 Manuals HP 3000 Manuals
RJE/V CS Errors (continued)
---------------------------------------------------------------------------------------
120 MESSAGE CS ERROR 120
CAUSE The INP driver detected an irrecoverable internal error. This
could be a software problem with the driver or download.
ACTION Collect any INPLOGxx.PUB.SYS and LOGxxxx.PUB.SYS and contact
your HP representative.
---------------------------------------------------------------------------------------
121 MESSAGE CS ERROR 121
CAUSE ROM self test error. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
122 MESSAGE CS ERROR 122
CAUSE Internal hardware error with INP: HPIB error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
123 MESSAGE CS ERROR 123
CAUSE Internal hardware error with INP: GIC error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
124 MESSAGE CS ERROR 124
CAUSE While INP was executing in RAM, a reset command was issued by
the driver. Also after a user aborts RJE, any subsequent I/O
sent to the driver before shutdown is completed with a CS ERROR
124 indicating that I/O on this link has been aborted.
ACTION No action.
---------------------------------------------------------------------------------------
151 MESSAGE CS ERROR 151
CAUSE The INP connect timer expired. This happens when the modem
does not raise DSR within connect timeout seconds. Usually
because of failure to connect with remote modem or dial
facility. It could also be because of a bad local modem or
connection.
ACTION Check the cable connections, the modems, and the phone number
if dialing into a facility.
---------------------------------------------------------------------------------------
153 MESSAGE CS ERROR 153
CAUSE Remote station rejected the connection.
ACTION Take CS traces of the problem, check for valid ID sequences,
and contact your HP representative.
---------------------------------------------------------------------------------------
154 MESSAGE CS ERROR 154
CAUSE The MPE system, INP driver and INP card have detected a power
failure.
ACTION Retry the operation.
---------------------------------------------------------------------------------------
155 MESSAGE CS ERROR 155
CAUSE The INP local timer expired. This happens when RJE does not
send requests to the INP within the specified number of seconds
for local timeout.
ACTION Retry the RJE command.
---------------------------------------------------------------------------------------
156 MESSAGE CS ERROR 156
CAUSE Irrecoverable internal error detected by the CS driver.
ACTION Take CS traces of the problem, check for INPLOGS and
LOGxxxx.PUB.SYS. Contact your HP representative, an MPE system
dump may be necessary.
---------------------------------------------------------------------------------------
157 MESSAGE CS ERROR 157
CAUSE The local INP has detected a protocol error by the remote
station which is irrecoverable.
ACTION Take CS traces of the problem, and protocol analyzer traces.
Contact your HP representative.
---------------------------------------------------------------------------------------
158 MESSAGE CS ERROR 158
CAUSE The remote station sent a DLE EOT disconnect sequence to inform
us that it is disconnecting.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
160 MESSAGE CS ERROR 160
CAUSE MPE detected an error while trying to make a segment present.
ACTION Take a dump of the MPE system. Contact your HP representative.
---------------------------------------------------------------------------------------
201 MESSAGE CS ERROR 201
CAUSE A user issued an abort I/O command on the RJE link.
ACTION No action.
---------------------------------------------------------------------------------------
202 MESSAGE CS ERROR 202
CAUSE The INP driver received a CS request that it did not recognize
as valid.
ACTION Take a CS trace. Contact your HP representative.
---------------------------------------------------------------------------------------
203 MESSAGE CS ERROR 203
CAUSE The remote station sent a NAK in response to a linebid; that
is, the remote is not ready for linebid.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
204 MESSAGE CS ERROR 204
CAUSE The remote station sent a NAK sequence in response to a
linebid. This happens when remote does not recognize the local
ID sequence.
ACTION Try another ID sequence.
---------------------------------------------------------------------------------------
205 MESSAGE CS ERROR 205
CAUSE The remote primary station bid for the line at the same time
the local bid for the line; line bid failed.
ACTION Since the remote is primary, the local user should issue an
#RJOUT to receive the remote station's data.
---------------------------------------------------------------------------------------
206 MESSAGE CS ERROR 206
CAUSE While the local was sending data, the remote sent an RVI
indicating that it had an urgent message to send.
ACTION The current user should issue an #RJOUT command to receive the
remote station's message.
---------------------------------------------------------------------------------------
207,1 MESSAGE CS ERROR 207,1
CAUSE Transmission retry count was exhausted. The remote station
either sent an ID while bidding for the line or while
acknowledging a BID, which is not in the local stations list of
valid remote IDs.
ACTION The user should update the remote ID list or should try
connecting to a link with a known ID.
---------------------------------------------------------------------------------------
207,2 MESSAGE CS ERROR 207,2
CAUSE Transmission retry count was exhausted. An unintelligible
sequence was received from remote. This is normally caused by
a noisy line.
ACTION Contact your HP representative to test the quality of the line
and modems.
---------------------------------------------------------------------------------------
207,3 MESSAGE CS ERROR 207,3
CAUSE Transmission retry count was exhausted. Block check character
error. This is normally caused by a noisy line. A text block
sequence sent by the remote station was garbled on the line and
the local station responded with a NAK for the specified number
of retries.
ACTION Contact your HP representative to test the quality of the line
and modems.
---------------------------------------------------------------------------------------
207,4 MESSAGE CS ERROR 207,4
CAUSE Transmission retry count was exhausted. Remote did not respond
to text. The local station times out and sends an ENQ
requesting a response from remote. If the retry count is
exhausted, the local will give up and report this error.
ACTION Contact your HP representative to test the quality of the line
and modems.
---------------------------------------------------------------------------------------
207,5 MESSAGE CS ERROR 207,5
CAUSE Transmission retry count was exhausted. Received incorrect
acknowledgement. The remote station protocol is out of sync
with local.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
207,6 MESSAGE CS ERROR 207,6
CAUSE Transmission retry count was exhausted. Remote attempted to
bid for line while local primary bid. Usually this happens
when both the remote and local think they are primary.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
207,7 MESSAGE CS ERROR 207,7
CAUSE Transmission retry count was exhausted. Remote did not respond
to linebid. If level one connection is established and the
remote is not responding to local's bid, this usually means the
remote is not seeing the linebid possibly because of a bad
cable connection.
ACTION Contact your HP representative to test the quality of the line
and modems. Check all cable connections.
---------------------------------------------------------------------------------------
207,8 MESSAGE CS ERROR 207,8
CAUSE Transmission retry count was exhausted. Received
unintelligible sequence after sending text or control sequence.
Data was probably garbled during transmission.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If the problem occurs repeatedly, contact your HP
representative.
---------------------------------------------------------------------------------------
207,9 MESSAGE CS ERROR 207,9
CAUSE Transmission retry count was exhausted. Remote sent ENQ to
local station's text block.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
207,10 MESSAGE CS ERROR 207,10
CAUSE Transmission retry count was exhausted. The remote sent an ENQ
to request a retransmission of the local's last response.
ACTION Take a CS trace of the problem. Contact your HP representative
to test the quality of the line and modems. Check all cable
connections.
---------------------------------------------------------------------------------------
207,11 MESSAGE CS ERROR 207,11
CAUSE Transmission retry count was exhausted. The text sent by the
local station was garbled during transmission and the remote
station requested a resend.
ACTION Contact your HP representative to test the quality of the line
and modems. Check all cable connections.
---------------------------------------------------------------------------------------
207,12 MESSAGE CS ERROR 207,12
CAUSE Transmission retry count was exhausted. The local station
received an unexpected EOT while in control state.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
207,13 MESSAGE CS ERROR 207,13
CAUSE Transmission retry count was exhausted. More data than
expected was transmitted by the remote station, causing a
receive text overflow. Sometimes a noisy line can cause this
symptom.
ACTION Take a CS trace of the problem. Contact your HP representative
to test the quality of the line and modems. Check all cable
connections.
---------------------------------------------------------------------------------------
207,14 MESSAGE CS ERROR 207,14
CAUSE Transmission retry count was exhausted. A data overrun has
occurred in SIO multiplexer during an I/O operation.
ACTION Run DSM. Contact your HP representative.
---------------------------------------------------------------------------------------
207,15 MESSAGE CS ERROR 207,15
CAUSE Transmission retry count was exhausted. A mismatch has
occurred between expected and actual data on SIO multiplexer.
ACTION Take a CS trace of the problem. Collect INPLOGxx.PUB.SYS and
LOGxxxx.PUB.SYS. Contact your HP representative.
---------------------------------------------------------------------------------------
208 MESSAGE CS ERROR 208
CAUSE The remote station sent text while local station was expecting
a control sequence.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
209 MESSAGE CS ERROR 209
CAUSE The receive timer (INP) expired while waiting for text from the
remote station. This usually means the remote system could not
respond in time, or the system is no longer communicating with
your system.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation.
---------------------------------------------------------------------------------------
210 MESSAGE CS ERROR 210
CAUSE Remote sent unexpected EOT; probably due to an irrecoverable
error.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
211 MESSAGE CS ERROR 211
CAUSE Immediately preceding the issuing of an I/O request, the remote
station sent a EOT and disconnect sequence to inform us that it
is disconnecting.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
213 MESSAGE CS ERROR 213
CAUSE The remote station sent an acknowledgement in response to
local's CREAD acknowledgement. This happens because of a
confused remote violating protocol.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
214 MESSAGE CS ERROR 214
CAUSE The remote station sent an negative acknowledgement in response
to local's CREAD acknowledgement. This happens because of a
confused remote violating protocol.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
215 MESSAGE CS ERROR 215
CAUSE The remote station sent an RVI in response to local's CREAD
acknowledgement. This happens because of a confused remote
violating protocol.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
217 MESSAGE CS ERROR 217
CAUSE No line bid was received from remote stations; local station
timed out.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation.
---------------------------------------------------------------------------------------