HP 3000 Manuals HP 3000 Manuals
RJE/V CS Errors
---------------------------------------------------------------------------------------
1 MESSAGE CS ERROR 1
CAUSE An internal error was encountered during OPEN. Usually because
an internal resource could not be obtained such as creating an
object or IOWAIT port, or not getting a system PLABEL, etc.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
5 MESSAGE CS ERROR 5
CAUSE Not enough stack space to process the line opening.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
6 MESSAGE CS ERROR 6
CAUSE An invalid driver name was encountered during COPEN.
ACTION Change configuration to proper driver name.
---------------------------------------------------------------------------------------
7 MESSAGE CS ERROR 7
CAUSE The driver is not installed on the system.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
8 MESSAGE CS ERROR 8
CAUSE The driver is not compatible with the attributes of the
communication line.
ACTION Reconfigure the communications interface.
---------------------------------------------------------------------------------------
9 MESSAGE CS ERROR 9
CAUSE If a driver name other than IOINP0 or IOINP1 is specified and
the driver changeable is set to no, then this error is
generated.
ACTION Only IOINP0 and IOINP1 is supported on the INP. Change the
configuration to use one of these.
---------------------------------------------------------------------------------------
10 MESSAGE CS ERROR 10
CAUSE The specified device could not be found in the configuration.
ACTION Either configure the device into the system, or select a device
which is already configured.
---------------------------------------------------------------------------------------
11 MESSAGE CS ERROR 11
CAUSE The INP associated with this device is not available. Possible
reasons include the specified INP having the wrong channel
number or being incorrectly configured.
ACTION Correct the configuration to agree with the cards channel
address or verify that the device is not already in use.
---------------------------------------------------------------------------------------
12 MESSAGE CS ERROR 12
CAUSE The specified logical device was not an INP.
ACTION Check the configuration and correct the logical device.
---------------------------------------------------------------------------------------
13 MESSAGE CS ERROR 13
CAUSE The specified link device is already in use by another
subsystem.
ACTION Either terminate the other subsystem or specify another device.
---------------------------------------------------------------------------------------
14 MESSAGE CS ERROR 14
CAUSE The INP rejected the ID sequence during configuration because
of an invalid length.
ACTION Correct the ID sequence.
---------------------------------------------------------------------------------------
15 MESSAGE CS ERROR 15
CAUSE Invalid buffer size.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
17 MESSAGE CS ERROR 17
CAUSE Invalid phone number length.
ACTION Correct the phone number in the configuration or #RJLINE
command.
---------------------------------------------------------------------------------------
18 MESSAGE CS ERROR 18
CAUSE The specified phone number contains illegal characters.
ACTION Consult the description of telephone number under the #RJLINE
command in chapter 3, "RJE User Commands," then correct the
phone number in the configuration or #RJLINE command.
---------------------------------------------------------------------------------------
19 MESSAGE CS ERROR 19
CAUSE A parameter in the configuration is not compatible with RJE.
ACTION Correct the configuration or use a default.
---------------------------------------------------------------------------------------
20 MESSAGE CS ERROR 20
CAUSE The MISC array contains an invalid information type.
ACTION Check the configuration and correct the problem.
---------------------------------------------------------------------------------------
21 MESSAGE CS ERROR 21
CAUSE The MISC array contains an invalid value.
ACTION Check the configuration and correct the problem.
---------------------------------------------------------------------------------------
24 MESSAGE CS ERROR 24
CAUSE The specified trace file is already being exclusively accessed,
or some other file system error occurred while opening the
trace file.
ACTION Choose another name for the trace file. Contact your HP
representative if not able to solve problem.
---------------------------------------------------------------------------------------
25 MESSAGE CS ERROR 25
CAUSE The trace process was unable to obtain an extra data segment.
ACTION Add more memory to the system, or possibly reconfigure the
existing system.
---------------------------------------------------------------------------------------
26 MESSAGE CS ERROR 26
CAUSE The user must have CS capability.
ACTION Alter the user's capabilities.
---------------------------------------------------------------------------------------
27 MESSAGE CS ERROR 27
CAUSE The formal designator on the CLINE is not correct.
ACTION The correct formal designator is RJELINE.
---------------------------------------------------------------------------------------
28 MESSAGE CS ERROR 28
CAUSE No logical device was specified in the #RJLINE statement, and
no RJLINE device class (the default) was defined in the
configuration.
ACTION Specify an LDEV or device class name in the #RJLINE command, or
define a device class RJLINE in the configuration.
---------------------------------------------------------------------------------------
29 MESSAGE CS ERROR 29
CAUSE Too many files/lines. No PCBXSPACE is obtainable. This
happens while getting space for the INP driver's DIT.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
31 MESSAGE CS ERROR 31
CAUSE The RJE subsystem could not get enough memory from the system
for work space.
ACTION Have an HP representative evaluate the memory.
---------------------------------------------------------------------------------------
32 MESSAGE CS ERROR 32
CAUSE The INP was not able to properly open or configure.
ACTION Look for console messages and system log messages. Collect
this data and contact your HP representative.
---------------------------------------------------------------------------------------
35 MESSAGE CS ERROR 35
CAUSE The INP download CSDBSCX.PUB.SYS is either corrupt or missing.
ACTION Replace the download with a known good one.
---------------------------------------------------------------------------------------
38 MESSAGE CS ERROR 38
CAUSE The trace process could not be started when the user invoked
trace because of an internal error.
ACTION Look for console messages and system log messages. Collect
data and contact your HP representative.
---------------------------------------------------------------------------------------
39 MESSAGE CS ERROR 39
CAUSE The INP has determined that there is not enough buffer space
for normal operation.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
42 MESSAGE CS ERROR 42
CAUSE An autodial attempt was made while the modem was already busy.
ACTION Use another modem or wait until the modem is available.
---------------------------------------------------------------------------------------
44 MESSAGE CS ERROR 44
CAUSE Power has not been supplied to the autodial modem.
ACTION Test modem and connections.
---------------------------------------------------------------------------------------
48 MESSAGE CS ERROR 48
CAUSE No virtual memory available for trace and/or buffering.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
49 MESSAGE CS ERROR 49
CAUSE DB not pointing at stack. This is an internal error.
ACTION Take an MPE system dump and contact your HP representative.
---------------------------------------------------------------------------------------
50 MESSAGE CS ERROR 50
CAUSE User needs process handling (PH) capability to do tracing.
ACTION Alter the capabilities to include PH.
---------------------------------------------------------------------------------------
51 MESSAGE CS ERROR 51
CAUSE Invalid line number - no such line. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
52 MESSAGE CS ERROR 52
CAUSE Invalid parameter value. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
53 MESSAGE CS ERROR 53
CAUSE An error occurred while CS was sending a trace read request to
driver.
ACTION No action required.
---------------------------------------------------------------------------------------
54 MESSAGE CS ERROR 54
CAUSE An error occurred when an autodial attempt was made due to one
of the following: An RS366A autodial cable is not installed on
the INP; the remote modem was busy; the remote modem did not
answer.
ACTION Check to see if the appropriate RS366A autodial cable is
attached to the PSI or try another number.
---------------------------------------------------------------------------------------
55 MESSAGE CS ERROR 55
CAUSE No phone list exists.
ACTION Update the configuration to include a phone list.
---------------------------------------------------------------------------------------
56 MESSAGE CS ERROR 56
CAUSE Invalid buffer count parameter. This is an internal error
encountered during CWRITE.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
57 MESSAGE CS ERROR 57
CAUSE The console operator replied with a NO to the dial prompting
message displayed on the console possibly because the line was
busy or the remote stations is not answering the call.
ACTION Try another phone number or retry the operation.
---------------------------------------------------------------------------------------
58 MESSAGE CS ERROR 58
CAUSE A dial attempt occurred but no phone list was available.
ACTION Update the configuration to include a phone list.
---------------------------------------------------------------------------------------
59 MESSAGE CS ERROR 59
CAUSE The autodial unit received an undecipherable character.
ACTION Try another phone number. If problem persists, contact your HP
representative.
---------------------------------------------------------------------------------------
60 MESSAGE CS ERROR 60
CAUSE Invalid array length. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
61 MESSAGE CS ERROR 61
CAUSE CS was processing a CCONTROL request which had an invalid
control code.
ACTION Contact your HP representative. Take a CS trace.
---------------------------------------------------------------------------------------
63 MESSAGE CS ERROR 63
CAUSE The user issued an abort request on an logical device or link
that had no outstanding IO.
ACTION No action required.
---------------------------------------------------------------------------------------
64 MESSAGE CS ERROR 64
CAUSE Abort ignored. The IO already completed or was previously
aborted.
ACTION No action required.
---------------------------------------------------------------------------------------
70 MESSAGE CS ERROR 70
CAUSE Exceeds max writes allowed outstanding. This is an internal
error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
71 MESSAGE CS ERROR 71
CAUSE Exceeds maximum reads allowed outstanding. This is an internal
error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
73 MESSAGE CS ERROR 73
CAUSE Parameter bounds violation. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
74 MESSAGE CS ERROR 74
CAUSE No CS buffers remaining. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
76 MESSAGE CS ERROR 76
CAUSE Buffer parameter required, but not specified. This is an
internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
77 MESSAGE CS ERROR 77
CAUSE Maximum number of I/O requests are already outstanding. The
CREAD/CWRITE intrinsics can only handle one read or write at a
time. Must first issue IOWAIT. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
78 MESSAGE CS ERROR 78
CAUSE No I/O pending for any file/line. An IOWAIT was issued when no
outstanding IO existed. This is an internal error.
ACTION This is an internal error, please contact your HP
representative.
---------------------------------------------------------------------------------------
79 MESSAGE CS ERROR 79
CAUSE No I/O pending for specified file line. An IOWAIT was issued
when no outstanding IO existed. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
80 MESSAGE CS ERROR 80
CAUSE Illegal operation on INP. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
81 MESSAGE CS ERROR 81
CAUSE A file system error occurred while opening or writing to an
INPLOGxx.PUB.SYS file.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
84 MESSAGE CS ERROR 84
CAUSE INP USYNRT failure with DMA. Internal hardware error with INP.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
85 MESSAGE CS ERROR 85
CAUSE INP parity error. Internal hardware error with INP.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
86 MESSAGE CS ERROR 86
CAUSE RAM software error. Internal hardware error with INP.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
87 MESSAGE CS ERROR 87
CAUSE INP received bad self test control character. Internal
hardware error with INP.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
88 MESSAGE CS ERROR 88
CAUSE INP DMA self test error. Internal hardware error with INP.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
89 MESSAGE CS ERROR 89
CAUSE INP microprocessor (MC 2) failure. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
90 MESSAGE CS ERROR 90
CAUSE INP ROM failure. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
91 MESSAGE CS ERROR 91
CAUSE INP RAM failure. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
92 MESSAGE CS ERROR 92
CAUSE INP USART transmitter overrun. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
93 MESSAGE CS ERROR 93
CAUSE INP USART parity error. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
94 MESSAGE CS ERROR 94
CAUSE INP USART self test receive error. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
95 MESSAGE CS ERROR 95
CAUSE INP USYNRT self test transmit error. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
96 MESSAGE CS ERROR 96
CAUSE INP USYNRT self test receive error. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
97 MESSAGE CS ERROR 97
CAUSE INP USYNRT self test receive overrun. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
98 MESSAGE CS ERROR 98
CAUSE INP USYNRT self test receive aborted. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
99 MESSAGE CS ERROR 99
CAUSE INP USYNRT self test receive no data. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
101 MESSAGE CS ERROR 101
CAUSE INP is not receiving clock.
ACTION Check cable connection.
---------------------------------------------------------------------------------------
102 MESSAGE CS ERROR 102
CAUSE SIO TRANSFER error. A DMA transfer from the DRIVER to INP or
from INP to DRIVER failed because too much or too little data
was transferred.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
103 MESSAGE CS ERROR 103
CAUSE Modem DSR signal dropped. Modem failure, or line failure
(remote may have disconnected line).
ACTION Contact HP representative to test modem and line quality.
---------------------------------------------------------------------------------------
104 MESSAGE CS ERROR 104
CAUSE Carrier loss. The modem may have disconnected, the phone line
may have a problem, or the remote may have dropped modem
signals without sending disconnect sequence.
ACTION Contact HP representative to test modem and line quality.
---------------------------------------------------------------------------------------
105 MESSAGE CS ERROR 105
CAUSE Data overrun on INP.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
106 MESSAGE CS ERROR 106
CAUSE INP USYNRT received no data. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
107 MESSAGE CS ERROR 107
CAUSE INP USART failure with DMA. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
108 MESSAGE CS ERROR 108
CAUSE INP timer failure. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
109 MESSAGE CS ERROR 109
CAUSE INP RAM parity error. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
110 MESSAGE CS ERROR 110
CAUSE Not enough memory left on INP for tracing.
ACTION Decrease number of entries per record parameter.
---------------------------------------------------------------------------------------
111 MESSAGE CS ERROR 111
CAUSE Illegal number of trace buffers requested. Internal hardware
error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
112 MESSAGE CS ERROR 112
CAUSE Illegal start/stop requests. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
113 MESSAGE CS ERROR 113
CAUSE Illegal trace record size specified. Internal hardware error.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
115 MESSAGE CS ERROR 115
CAUSE A power fail occurred while CS was downloading the INP.
ACTION No action.
---------------------------------------------------------------------------------------
116 MESSAGE CS ERROR 116
CAUSE The mainframe IC driver timed out before the INP completed a
request.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
117 MESSAGE CS ERROR 117
CAUSE Invalid interrupt. Usually caused when the INP is informing
the driver of an irrecoverable condition.
ACTION Collect the INPLOGxx.PUB.SYS and contact your HP
representative.
---------------------------------------------------------------------------------------
118 MESSAGE CS ERROR 118
CAUSE Start/stop I/O error. A problem was encountered with the MPE
I/O program. This is generally a hardware problem.
ACTION Run DSM and contact your HP representative.
---------------------------------------------------------------------------------------
119 MESSAGE CS ERROR 119
CAUSE An error occurred during power fail recovery.
ACTION Collect any INPLOGxx.PUB.SYS and contact your HP
representative.
---------------------------------------------------------------------------------------