HP 3000 Manuals HP 3000 Manuals
RJE/XL CS Errors
---------------------------------------------------------------------------------------
1 MESSAGE CS ERROR 1
CAUSE An internal error was encountered during OPEN. Usually because
an internal resource could not be obtained such as creating an
object or IOWAIT port, or not getting a system PLABEL, etc.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
7 MESSAGE CS ERROR 7
CAUSE The driver is not installed on the system.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
10 MESSAGE CS ERROR 10
CAUSE The specified linkname could not be found in the configuration.
ACTION Either configure the linkname into the system, or select a
linkname which is already configured.
---------------------------------------------------------------------------------------
11 MESSAGE CS ERROR 11
CAUSE The PSI associated with this linkname is not available.
Possible reasons are the card being in the wrong slot (MPE XL).
ACTION Correct the configuration to agree with the cards channel
address or physical slot location.
---------------------------------------------------------------------------------------
13 MESSAGE CS ERROR 13
CAUSE The specified link device is already in use.
ACTION No action required.
---------------------------------------------------------------------------------------
15 MESSAGE CS ERROR 15
CAUSE The ROPEN command encountered a buffer manager error while
trying to get buffers for read and write requests.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
19 MESSAGE CS ERROR 19
CAUSE A parameter in the configuration is not supported.
ACTION Correct the configuration or use a default.
---------------------------------------------------------------------------------------
26 MESSAGE CS ERROR 26
CAUSE The user must have CS capability.
ACTION Alter the user's capabilities.
---------------------------------------------------------------------------------------
31 MESSAGE CS ERROR 31
CAUSE The RJE subsystem could not get enough memory from the system
for work space.
ACTION Have an HP representative evaluate the memory.
---------------------------------------------------------------------------------------
32 MESSAGE CS ERROR 32
CAUSE The PSI was not able to properly open or configure.
ACTION Look for error messages from the DRIVER on the system console,
and for messages in the system log (LOGxxxx.PUB.SYS). Collect
this data and call your HP representative.
---------------------------------------------------------------------------------------
35 MESSAGE CS ERROR 35
CAUSE The PSI download file is either corrupt or missing.
ACTION Replace the download with a known good one.
---------------------------------------------------------------------------------------
38 MESSAGE CS ERROR 38
CAUSE The trace manager could not be started when the user invoked
trace because of an internal error.
ACTION Look for console messages and system log messages. Collect
data and contact your HP representative.
---------------------------------------------------------------------------------------
42 MESSAGE CS ERROR 42
CAUSE An autodial attempt was made while the modem was already busy.
ACTION Use an available autodial modem.
---------------------------------------------------------------------------------------
44 MESSAGE CS ERROR 44
CAUSE Power has not been supplied to the autodial modem.
ACTION Test modem and connections.
---------------------------------------------------------------------------------------
54 MESSAGE CS ERROR 54
CAUSE An error occurred when an autodial attempt was made due to one
of the following: An RS366A autodial cable is not installed on
the PSI; the remote modem was busy; the remote modem did not
answer.
ACTION Check to see if the appropriate RS366A autodial cable is
attached to the PSI or try another number.
---------------------------------------------------------------------------------------
57 MESSAGE CS ERROR 57
CAUSE The console operator replied with a NO to the dial prompting
message displayed on the console possibly because the line was
busy or the remote stations is not answering the call.
ACTION Try another phone number or retry the operation.
---------------------------------------------------------------------------------------
58 MESSAGE CS ERROR 58
CAUSE A dial attempt occurred but no phone list was available.
ACTION Update the configuration to include a phone list.
---------------------------------------------------------------------------------------
76 MESSAGE CS ERROR 76
CAUSE No buffer parameter. This is an internal error.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
77 MESSAGE CS ERROR 77
CAUSE The RREAD/RWRITE intrinsics can only handle one read or write
at a time.
ACTION This is an internal error, please contact your HP
representative.
---------------------------------------------------------------------------------------
103 MESSAGE CS ERROR 103
CAUSE Modem DSR signal dropped. Modem failure, or line failure
occurred (remote may have disconnected line).
ACTION Contact HP representative to test modem and line quality.
---------------------------------------------------------------------------------------
104 MESSAGE CS ERROR 104
CAUSE Modem failure, or line failure occurred. Remote dropped modem
signals without sending disconnect sequence.
ACTION Contact HP representative to test modem and line quality.
---------------------------------------------------------------------------------------
125 MESSAGE CS ERROR 125
CAUSE Modem CTS signal dropped. Modem or line failure occurred.
ACTION Contact your HP representative to test modem and line quality.
---------------------------------------------------------------------------------------
126 MESSAGE CS ERROR 126
CAUSE No or wrong cable attached to PSI.
ACTION Check cable connections.
---------------------------------------------------------------------------------------
151 MESSAGE CS ERROR 151
CAUSE The PSI connect timer expired. This happens when the modem
does not raise DSR within connect timeout seconds. Usually
because of failure to connect with remote modem or dial
facility. It could also be because of a bad local modem or
connection.
ACTION Check the cable connections, the modems, and the phone number
if dialing into a facility.
---------------------------------------------------------------------------------------
155 MESSAGE CS ERROR 155
CAUSE The PSI local timer expired. This happens when RJE does not
send requests to the PSI within the specified number of seconds
for local timeout.
ACTION Retry the RJE command.
---------------------------------------------------------------------------------------
156 MESSAGE CS ERROR 156
CAUSE Irrecoverable internal error detected by the driver.
ACTION Take CS traces of the problem, check for NETDMP## and
LOGxxxx.PUB.SYS. Contact your HP representative, an MPE system
dump may be necessary.
---------------------------------------------------------------------------------------
158 MESSAGE CS ERROR 158
CAUSE The remote station sent a DLE EOT disconnect sequence to inform
us that it is disconnecting.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
162 MESSAGE CS ERROR 162
CAUSE The PSI's heartbeat timeout has occurred. This happens if the
HP 3000 mainframe does communicate with the PSI card within a
certain amount of time.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
204 MESSAGE CS ERROR 204
CAUSE The remote station sent a NAK sequence in response to a
linebid. This happens when remote does not recognize the local
ID sequence.
ACTION Try another ID sequence.
---------------------------------------------------------------------------------------
205 MESSAGE CS ERROR 205
CAUSE The remote primary station bid for the line at the same time
the local bid for the line; line bid failed.
ACTION Since the remote is primary, the local user should issue an
#RJOUT to receive the remote station's data.
---------------------------------------------------------------------------------------
206 MESSAGE CS ERROR 206
CAUSE While the local was sending data, the remote sent an RVI
indicating that it had an urgent message to send.
ACTION The current user should issue an #RJOUT command to receive the
remote station's message.
---------------------------------------------------------------------------------------
207,1 MESSAGE CS ERROR 207,1
CAUSE Transmission retry count was exhausted. The remote station
either sent an ID while bidding for the line or while
acknowledging a BID, which is not in the local stations list of
valid remote IDs.
ACTION The user should update the remote ID list or should try
connecting to a link with a known ID.
---------------------------------------------------------------------------------------
207,2 MESSAGE CS ERROR 207,2
CAUSE Transmission retry count was exhausted. An unintelligible
sequence was received from remote. This is normally caused by
a noisy line.
ACTION Contact your HP representative to test the quality of the line
and modems.
---------------------------------------------------------------------------------------
207,3 MESSAGE CS ERROR 207,3
CAUSE Transmission retry count was exhausted. Block check character
error. This is normally caused by a noisy line. A text block
sequence sent by the remote station was garbled on the line and
the local station responded with a NAK for the specified number
of retries before giving up.
ACTION Contact your HP representative to test the quality of the line
and modems.
---------------------------------------------------------------------------------------
207,4 MESSAGE CS ERROR 207,4
CAUSE Transmission retry count was exhausted. Remote did not respond
to text. The local station times out and sends an ENQ
requesting a response from remote. If this happens retry
times, the local will give up and report this error.
ACTION Contact your HP representative to test the quality of the line
and modems.
---------------------------------------------------------------------------------------
207,7 MESSAGE CS ERROR 207,7
CAUSE Transmission retry count was exhausted. Remote did not respond
to linebid. If level one connection is established and the
remote is not responding to local's bid, this usually means the
remote is not seeing the linebid possibly because of a bad
cable connection.
ACTION Contact your HP representative to test the quality of the line
and modems. Check all cable connections.
---------------------------------------------------------------------------------------
207,10 MESSAGE CS ERROR 207,10
CAUSE Transmission retry count was exhausted. The remote sent an ENQ
to request a retransmission of the local's last response.
ACTION Take a CS trace of the problem. Contact your HP representative
to test the quality of the line and modems. Check all cable
connections.
---------------------------------------------------------------------------------------
207,11 MESSAGE CS ERROR 207,11
CAUSE Transmission retry count was exhausted. The text sent by the
local station was garbled during transmission and the remote
station requested a resend.
ACTION Contact your HP representative to test the quality of the line
and modems. Check all cable connections.
---------------------------------------------------------------------------------------
209 MESSAGE CS ERROR 209
CAUSE The text block timer (PSI) expired while waiting for text from
the remote station. This usually means the remote system could
not respond in time, or the system is no longer communicating
with your system.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation.
---------------------------------------------------------------------------------------
210 MESSAGE CS ERROR 210
CAUSE Remote sent unexpected EOT; probably due to an irrecoverable
error.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation. If protocol problems with the remote or INP are
indicated, contact your HP representative.
---------------------------------------------------------------------------------------
217 MESSAGE CS ERROR 217
CAUSE No line bid was received from remote stations; local station
timed out.
ACTION An #RJCONTINUE procedure can be used to recover from this
situation.
---------------------------------------------------------------------------------------