Level: 1 CLAS0001
CAUSE: RLM's data structures are corrupted.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 3 CLAS0002
CAUSE:Send_msg procedure returned a bad status to the
RLM.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 4 CLAS0002
CAUSE: Link Error occurred in unexpected state.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 5 CLAS0002
CAUSE: RLM could not rendezvous ("bind") with the MCM.
ACTION: Check the LAN hardware on the HP e3000. If no problem is
found, see Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 6 CLAS0001
CAUSE: Internal state mismatch within the RLM module.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 7 CLAS0003
CAUSE: RLM is out of internal resources.
ACTION: The operator may be attempting to bring up more than the
maximum supported DTC links. If not, then see Appendix
A "Submitting a CR" of this manual.
MESSAGE: None
Level: 8 CLAS0002
CAUSE: Either the RLM or code that it invoked encountered
an unexpected trap.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 9 CLAS0002
CAUSE: RLM could not get a buffer to send an outbound
packet (PARM = Status returned by "bmgr_get_buffer").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 10 CLAS0003
CAUSE: RLM could not release some internal resources (PARM
= Status returned by "new_release_table_entry").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 11 CLAS0001
CAUSE: RLM attempted to release a resource that had already
been released.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 12 CLAS0002
CAUSE: RLM received a connect reply message from the link
that it did not recognize.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 13 CLAS0003
CAUSE: The DTC is not responding to the HP e3000's
connection attempts. (i.e., The HP e3000 could not establish an
AFCP link control connection with the DTC.)
ACTION: Check state of DTC and LAN hardware. If no problem can be
found, see Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 14 CLAS0001
CAUSE: RLM's data structures are corrupted.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 15 CLAS0002
CAUSE: RLM could not release internal resources.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 16 CLAS0002
CAUSE: RLM received disconnect reply that did not match
any transaction in progress.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 17 CLAS0001
CAUSE: State mismatch within RLM's data structures.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 18 CLAS0002
CAUSE: RLM received an inbound data packet over a connection
that is down.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 19 CLAS0002
CAUSE: RLM could not write outbound packet to buffer.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 20 CLAS0002
CAUSE: RLM could not read buffer containing inbound packet.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 21 CLAS0001
CAUSE: Mismatch in states between the DTC and the HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 22 CLAS0002
CAUSE: Mismatch in states between DTC and HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 23 CLAS0001
CAUSE: Mismatch in states between the DTC and the HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 24 CLAS0001
CAUSE: Mismatch in states between the DTC and the HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 25 CLAS0003
CAUSE: DTC returned bad status during link shutdown (PARM
= status returned by DTC).
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 26 CLAS0002
CAUSE: Subsystem (NS Transport) specified invalid link.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 27 CLAS0003
CAUSE: Subsystem (NS Transport) attempted to connect X.25
card that was in a bad state.
ACTION: Check status of X.25 protocol on DTC. Possible
causes include bad/disconnected cable between DTC and switch/X.25
network, or the switch/X.25 network is down. When problem is corrected,
HP e3000 will display additional logging messages.
MESSAGE: None
Level: 28 CLAS0002
CAUSE: Disconnect reply received from linkn contained
bad status.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 29 CLAS0002
CAUSE: Subsystem specified a bad parameter in a connect
or disconnect request.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 30 CLAS0001
CAUSE: Control mismatch between DTC and HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 31 CLAS0002
CAUSE: DTC sent bad packet to HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 32 CLAS0002
CAUSE: Could not separate ("unbind") with link.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 33 CLAS0002
CAUSE: RLM attempted to send on a connection that was down.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 34 CLAS0003
CAUSE: Close request received while resources were outstanding.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 35 CLAS0002
CAUSE: Received packet from link on unknown connection.
ACTION: See Appendix A "Submitting a CR"
of this manual.
Level: 39 CLAS0002
CAUSE: State mismatch between DTC and Host.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 40 CLAS0002
CAUSE: DTC sent unknown packet to HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual. (Make sure a dump is taken of both the DTC and the
HP e3000.)
MESSAGE: None
Level: 41 CLAS0001
CAUSE: Data Structure state mismatches detected while
processing a link failure.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 42 CLAS0001
CAUSE: RLM's data structures are corrupted.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 43 CLAS0001
CAUSE: RLM's data structures are corrupted.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 44 CLAS0003
CAUSE: A shutdown occurred with resources outstanding.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 45 CLAS0002
CAUSE: RLM could not release a semaphore.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 46 CLAS0002
CAUSE: RLM data structures are in an invalid state for the event.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 47 CLAS0003
CAUSE: Unexpected status sent by DTC.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 48 CLAS0001
CAUSE: Interface problem between DTC and HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 49 CLAS0002
CAUSE: Link sent a disconnect event for an unknown connection.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 50 CLAS0001
CAUSE: AFCP connection is in an invalid state for the event.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 51 CLAS0002
CAUSE: DTC sent an invalid packet to the HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 52 CLAS0002
CAUSE: The DTC sent an invalid packet to the HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 53 CLAS0003
CAUSE: The DTC sent bad status to HP e3000.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 54 CLAS0002
CAUSE: RLM could not find the expected timer message.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 55 CLAS0002
CAUSE: RLM could not release timer resource.
ACTION: See Appendix A "Submitting a CR"
of this manual.
Level: 60 CLAS0002
CAUSE: Invalid message received for current state.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 61 CLAS0003
CAUSE: Link has gone down.
ACTION: Run appropriate diagnostics. If no error is found, see
Appendix A "Submitting a CR"
of this manual.
Level: 85 CLAS0002
CAUSE: RLM could not delete semaphore pool.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 88 CLAS0004
CAUSE: Link went down in an error condition.
ACTION: Check the status of the DTC.
MESSAGE: None
Level: 90 CLAS0002
CAUSE: RLM could not release semaphore.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 92 CLAS0005
CAUSE: DTC Link has gone down.
ACTION: Check the DTC X.25 card status.
MESSAGE: None
Level: 93 CLAS0005
CAUSE: X.25 Level3 Protocol on DTC is ready.
ACTION: None.
MESSAGE: None
Level: 94 CLAS0003
CAUSE: X.25 Level3 Protocol on DTC is not ready.
ACTION: Check the status of the DTC.
MESSAGE: None
Level: 95 CLAS0003
CAUSE: Host has lost contact with DTC.
ACTION: Check status of DTC.
MESSAGE: None
Level: 96 CLAS0003
CAUSE: Host has successfully communicated with DTC, but
X.25 level 3 protocol on DTC is not ready.
ACTION: Check status of X.25 protocol on DTC. Possible
causes include bad/disconnected cable between DTC and switch/X.25
network, or the switch/X.25 network is down. When problem is corrected,
HP e3000 will display additional logging messages and the network
will be usable.
MESSAGE: None
Level: 100 CLAS0002
CAUSE: Could not create the RLM's Port Data Area (PARM =
"create_object" status). Available virtual space may have been
exhausted.
ACTION: Contact your Hewlett-Packard representative and/or see
Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 101 CLAS0002
CAUSE: Could not obtain plabel for NL.PUB.SYS procedure
"remote_link_manager." Possible software installation problem
(PARM = status returned by "hpgetsysplabel").
ACTION: Check the status of the DTC.
MESSAGE: None
Level: 102 CLAS0002
CAUSE: Could not create the port for the RLM server (PARM
= status returned from "create_port").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 103 CLAS0002
CAUSE: Could not create the port for the RLM server (PARM
= status returned from "create_port").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 104 CLAS0003
CAUSE: Could not open AFCP protocol module (PARM = status returned
from "mcm_module_config").
ACTION: Check X.25 and DTS Link configuration. If no problem is
found, see Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 105 CLAS0001
CAUSE: Could not send message to the RLM server. (PARM
= status returned from "send_msg").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 106 CLAS0002
CAUSE: Could not obtain information on per process port
(PARM = status returned from "port_info").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 107 CLAS0001
CAUSE: Error encountered while receiving information from
RLM Server (PARM = status returned by "extend_receive").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 108 CLAS0001
CAUSE: Message received on process port if not the expected type.
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 109 CLAS0002
CAUSE: Link buffer size is too small.
ACTION: Check X.25 and DTC Link configuration. If no problems are
found, see Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 110 CLAS0003
CAUSE: Could not open the file NMCONFIG.PUB.SYS
(PARM = status returned by "nmconfopen").
ACTION: Check the nmconfig.pub.sys with the program
"FSCHECK". If no obvious problem is found, see
Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 111 CLAS0003
CAUSE: Could not read the Node Name from NMCONFIG.PUB.SYS
(PARM = status returned by "nmconfgetdata").
ACTION: Add nodename to configuration.
MESSAGE: None
Level: 112 CLAS0003
CAUSE: RLM could not close NMCONFIG.PUB.SYS
(PARM = status returned by "nmconfclose").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 113 CLAS0002
CAUSE: Could not create the RLM's inbound buffer
pool (PARM = status returned from "bmgr_create_pool").
ACTION: Check configuration file for excessive buffer
configuration. Reduce the number of buffers if possible. If no problems are
found, see Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 114 CLAS0002
CAUSE: Could not release the RLM's inbound buffer
pool (PARM = status returned by "bmgr_delete_pool").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 115 CLAS0003
CAUSE: RLM could not deconfigure AFCP protocol module
(PARM = status returned by "mcm_module_config").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 116 CLAS0003
CAUSE: RLM could not release plabel for
"remote_link_manager" (PARM = status returned by
"hprelsysplabel").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 117 CLAS0003
CAUSE: RLM could not delete the RLM's entry from
the CM port dictionary (PARM = status returned by "dict_delete").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 118 CLAS0002
CAUSE: RLM could not create the outbound buffer pool (PARM
= status returned by "bmgr_create_pool").
ACTION: Check configuration file for excessive buffer
configuration. Reduce the number of buffers if possible. If no problems are
found, see Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 119 CLAS0003
CAUSE: RLM could not reset subqueue mask (PARM = status
returned by "change_subqueue").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 120 CLAS0001
CAUSE: RLM could not update port dictionary (PARM = status
returned by "dict_update").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 121 CLAS0001
CAUSE: RLM could not update port dictionary (PARM = status
returned by "dict_update").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 122 CLAS0003
CAUSE: RLM could not delete the outbound buffer pool (PARM
= status returned by "bmgr_delete_pool").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 123 CLAS0003
CAUSE: RLM could purge its port (PARM = status returned
by "purge_port").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 124 CLAS0003
CAUSE: RLM could not release its port data area object
(PARM = status returned by "release_object").
ACTION: See Appendix A "Submitting a CR"
of this manual.
MESSAGE: None
Level: 125 CLAS0004
CAUSE: RLM has been created (PARM = RLM's port ID).
ACTION: None.
MESSAGE: None
Level: 126 CLAS0004
CAUSE: RLM has been shutdown.
ACTION: None.