Chapter 11 Store/Restore (Native Mode) and TurboSTORE/iX II
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II ♥ | |
| E0300 Volume I | |
| E0300 Volume II | |
| E0300 Volume III | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
Store/Restore (S/R) 707-799
- 707
- MESSAGE
STORE/RESTORE DOES NOT ALLOW MORE THAN TWENTY (20) "volumesetnames" TO BE SPECIFIED FOR THE 'SPLITVS' OPTION (S/R 707)
- CAUSE
You have included more than 20 volumesetnames on the same command line.
- ACTION
Retype the command and make sure not to exceed 20 volumesetnames.
- 708
- MESSAGE
"volumesetname" SPECIFIED DOES NOT EXIST (IS NOT MOUNTED) ON THIS SYSTEM IN SPLIT STATE (S/R 708)
- CAUSE
The specified volumesetname does not exist in the system or it is not mounted.
- ACTION
Retype the command and make sure you typed the volumesetname correctly and it is mounted.
- 709
- MESSAGE
A "volumesetname" IS SPECIFIED FOR ONVS AS WELL AS SPLITVS OPTION (S/R 709)
- CAUSE
A volumesetname included for the ONVS option cannot be specified for the SPLITVS option and vice versa.
- ACTION
Use different volumesetnames and retype the command.
- 710
- MESSAGE
'SPLITVS' OPTION CANNOT BE USED WITH THE 'PURGE' OPTION (S/R 710)
- CAUSE
SPLITVS and PURGE options are not allowed on the same command line.
- ACTION
Delete PURGE option and retype the command.
- 711
- MESSAGE
'SPLITVS' OPTION CANNOT BE USED WITH THE 'PURGE' OPTION (S/R 711)
- CAUSE
SPLITVS and PURGE options are not allowed in the same command line.
- ACTION
Delete either SPLITVS or PURGE option and retype the command.
- 712
- MESSAGE
'SPLITVS' OPTION CANNOT BE USED WITH THE 'ONLINE' OPTION (S/R 712)
- CAUSE
SPLITVS and ONLINE options are not allowed in the same command line.
- ACTION
Delete either SPLITVS or ONLINE option and retype the command.
- 713
- MESSAGE
'SPLITVS' OPTION CANNOT BE USED WITH THE 'DYNAMIC' OPTION (S/R 713)
- CAUSE
SPLITVS and DYNAMIC options are not allowed on the same command line.
- ACTION
Delete either SPLITVS or DYNAMIC option and retype the command.
- 721
- MESSAGE
'MOSET' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv (S/R 721)
- CAUSE
MOSET and TRANSPORT options are not allowed on the same command line.
- ACTION
CMSTORE and V/E caanot handle MOSET option. Delete either MOSET or TRANSPORT option and retype the command.
- 722
- MESSAGE
'MOSET' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 722)
- CAUSE
You specified MOSET option twice.
- ACTION
Delete one of the MOSET options and retype the command.
- 723
- MESSAGE
'MOSET' OPTION MAY NOT BE SPECIFIED IN CONJUNCTION WITH A POSITIONAL DEVICE FILE. Ex. 'STORE ....;*MO; MOSET=(MO1,MO2)' IS INVALID (S/R 723)
- CAUSE
The name of the device in the form of *MO should not be specified when using MOSET option.
- ACTION
Delete *MO from your command line and retype the command.
- 724
- MESSAGE
EXPECTED '=(device[,,..])[,(device[,...])]' AFTER 'MOSET' OPTION WHERE device IS A VALID LDEV NUMBER OR A DEVICE NAME.
SYNTAX
'MOSET=(device[,..])[,(device[,...])]' (S/R 724)
- CAUSE
You did not include a '=' sign after the MOSET option.
- ACTION
Retype the command line and include a '=' sign after the MOSET option.
- 725
- MESSAGE
EXPECTED A '(' TO START A MOSET. Ex. 'MOSET=(MO1,MO2).
SYNTAX
'MOSET=(device[,..])[,(device[,...])]' (S/R 725)
- CAUSE
You did not include a '(' to start a moset after the MOSET option.
- ACTION
Retype the command and include a '(' in your command line.
- 726
- MESSAGE
EXPECTED 'device' FILE SPECIFICATION IN MOSET. Ex. MOSET=(MO1,MO2).
SYNTAX
'MOSET=(device[,..])[,(device[,...])]' (S/R 726)
- CAUSE
Your MOSET includes invalid device names or ldev numbers.
- ACTION
Retype the command and include valid device names or ldev numbers.
- 727
- MESSAGE
MAXIMUM NUMBER OF 'device" SPECIFICATION EXCEEDED FOR A SERIAL MOSET. Ex. MOSET=(MO1,MO2,...MOn) EXCEEDS THE MAXIMUM OF 8 (S/R 727)
- CAUSE
You have included more than 8 devices for MOSET option.
- ACTION
Retype the command and type valid number of devices with MOSET option.
- 728
- MESSAGE
EXPECTED A ')' TO TERMINATE A SERIAL THE 'MOSET' OPTION.
SYNTAX
'MOSET=(device[,..])[,(device[,...])]' (S/R 728)
- CAUSE
You have not included a ')' to terminate your moset list after the MOSET option.
- ACTION
Retype the command and include a ')' to terminate your moset list.
- 729
- MESSAGE
EXPECTED A NAME AS 'device' FILE SPECIFICATION IN MOSET. NAME AND NUMERIC DEVICE SPECIFICATIONS CAN NOT BE SPECIFIED TOGETHER FOR THE MOSET OPTION (S/R 729)
- CAUSE
Mixing device names and ldev numbers are not allowed with MOSET option.
- ACTION
Either use all device names or ldev numbers with the MOSET option.
- 730
- MESSAGE
EXPECTED A NUMBER AS 'device' FILE SPECIFICATION IN MOSET. NAME AND NUMERIC DEVICE SPECIFICATIONS CAN NOT BE SPECIFIED TOGETHER FOR THE MOSET OPTION (S/R 730)
- CAUSE
Mixing device name and ldev numbers with MOSET option is not allowed.
- ACTION
Either use all device names or ldev numbers with the MOSET option.
- 731
- MESSAGE
'MOSET' OPTION NOT ALLOWED IN SYSGEN/STORE. (S/R 731)
- CAUSE
MOSET option is not allowed when STORE command is called inside SYSGEN.
- ACTION
Do not use MOSET option with STORE command from SYSGEN.
- 735
- MESSAGE
'NAME' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 735)
- CAUSE
The NAME option was entered twice.
- ACTION
Delete one of the NAME options and retype the command.
- 736
- MESSAGE
EXPECTED '=fname' AFTER 'NAME' OPTION WHERE fname IS THE NAME OF THE BACKUP YOU WANT TO USE FOR THIS OPERATION.
SYNTAX
'NAME=fname[.gname[.aname]]' (S/R 736).
- CAUSE
You have not included an '=' sign after the NAME option.
- ACTION
Include an '=' sign after the NAME option and retype the command.
- 737
- MESSAGE
EXPECTED 'fname' TO BE SPECIFIED FOR 'NAME' OPTION. A fname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH.
SYNTAX
'NAME=fname[.gname[.aname]]' (S/R 737).
- CAUSE
You have entered an invalid filename for the NAME option.
- ACTION
Retype the command and include a valid filename for NAME option.
- 738
- MESSAGE
EXPECTED '.gname' AFTER 'NAME' OPTION WHERE gname QUALIFIES NAME OF THE BACKUP YOU WANT TO USE FOR THIS OPERATION.
SYNTAX
'NAME=fname[.gname[.aname]]' (S/R 738).
- CAUSE
You have not included a '.' between fname and gname in your command line.
- ACTION
Include a '.' between fname and gname and retype the command.
- 739
- MESSAGE
EXPECTED 'gname' TO BE SPECIFIED FOR 'NAME' OPTION. A gname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH.
SYNTAX
'NAME=fname[.gname[.aname]]' (S/R 739).
- CAUSE
You have entered an invalid gname on your command line.
- ACTION
Retype the command and include a valid gname.
- 740
- MESSAGE
EXPECTED '.aname' AFTER 'NAME' OPTION WHERE aname QUALIFIES NAME OF THE BACKUP YOU WANT TO USE FOR THIS OPERATION.
SYNTAX
'NAME=fname[.gname[.aname]]' (S/R 740).
- CAUSE
You have not included a '.' between gname and aname on your command line.
- ACTION
Retype the command and include a '.' between gname and aname.
- 741
- MESSAGE
EXPECTED 'aname' TO BE SPECIFIED FOR 'NAME' OPTION. A aname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH.
SYNTAX
'NAME=fname[.gname[.aname]]' (S/R 741).
- CAUSE
You have entered an invalid account name with your command line.
- ACTION
Retype the command and include a valid account name.
- 743
- MESSAGE
MOSET OPTION IS REQUIRED WITH NAME OPTION FOR (RE)STORE TO MO. (S/R 743)
- CAUSE
MOSET option is a required parameter when you include NAME option on your command line.
- ACTION
Retype the command and include MOSET option.
- 744
- MESSAGE
NAME OPTION IS REQUIRED WITH MOSET OPTION FOR RESTORE FROM MO. (S/R 744)
- CAUSE
NAME option is a required parameter along with MOSET option during restore from magneto-optical.
- ACTION
Retype the command and include NAME option.
- 745
- MESSAGE
THE BACKUP FILE ON LDEV ! IS TOO SMALL FOR STORE TO MO. (S/R 745)
- CAUSE
The size of a file to be stored is too large for the magneto-optical media, probably because of defective optical media.
- ACTION
Retry with known good media.
- 746
- MESSAGE
INVALID FUNCTION ATTEMPTED ON LDEV ! FOR (RE)STORE TO MO. (S/R 746)
- CAUSE
An invalid function request was specified for the magneto-optical device.
- ACTION
Contact your HP Support Representative.
- 747
- MESSAGE
ATTEMPT TO OPEN THE BACKUP FILE NAMED ! ON LDEV ! ENCOUNTERED ERROR (S/R 747)
- CAUSE
Unable to open the specified backup media due to internal error.
- ACTION
Contact your HP Support representative for further assistance.
- 748
- MESSAGE
STORE/RESTORE ENCOUNTERED ERROR WHILE ATTEMPTING TO GET THE BYTE ADDRESS OF THE BACKUP FILE ON LDEV ! (S/R 748).
- CAUSE
Internal error occurred while storing to a magneto-optical device.
- ACTION
Contact your HP Support representative for further assistance.
- 749
- MESSAGE
THE BACKUP FILE ON LDEV ! CONTAINS MORE THAN 1 EXTENT. STORE CAN NOT HANDLE MULTIPLE EXTENT FILES FOR BACKUP TO DISC (S/R 749).
- CAUSE
A magneto-optical file has more than 1 extent.
- ACTION
Contact your HP Support Representative.
- 750
- MESSAGE
STORE WAS UNABLE TO ALLOCATE SPACE FOR 'MOSET' OPTION BUFFERS AND CONTROL BLOCKS. (S/R 750)
- CAUSE
Internal error occurred while storing to MOSET.
- ACTION
Contact your HP Support representative.
- 753
- MESSAGE
THE NAME OPTION IS NOT ALLOWED WITH THE TRANSPORT OPTION (S/R 753)
- CAUSE
NAME and TRANSPORT options are not allowed on the same command line.
- ACTION
TRANSPORT option is not valid with Magneto-optical devices. Check the syntax and retype your command.
- 760
- MESSAGE
WARNING: 'COPYACD' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 760)
- CAUSE
The COPYACD option was entered more than once.
- ACTION
Information only.
- 761
- MESSAGE
'COPYACD' AND 'NOACD' CANNOT BE USED TOGETHER (S/R 761)
- CAUSE
COPYACD and NOACD are not allowed on the same command line.
- ACTION
Delete either COPYACD or NOACD and retype the command.
- 765
- MESSAGE
WARNING: 'NOACD' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 765)
- CAUSE
The NOACD option was entered more than once.
- ACTION
Information only.
- 767
- MESSAGE
WARNING: 'LDEV' OPTION HAS BEEN REDUNDANTLY SPECIFIED. SYSGEN/STORE INTERFACE ERROR. (S/R 767)
- CAUSE
The LDEV option was entered more than once.
- ACTION
Information only.
- 768
- MESSAGE
'LDEV' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv. SYSGEN/STORE INTERFACE ERROR. (S/R 768)
- CAUSE
LDEV and TRANSPORT options are not allowed on the same command line.
- ACTION
TRANSPORT is not a valid option with STORE command from SYSGEN. Check your syntax and retype the command.
- 769
- MESSAGE
EXPECTED '=ldev' AFTER 'LDEV' OPTION.SYSGEN/STORE INTERFACE ERROR. (S/R 769)
- CAUSE
You did not enter a '=' sign after the LDEV option in your command line.
- ACTION
Retype the command and include '=' sign after the LDEV option.
- 770
- MESSAGE
EXPECTED 'LDEV=ldev' WHERE ldev IS A POSITIVE INTEGER. SYSGEN/STORE INTERFACE ERROR. (S/R 770)
- CAUSE
You have not entered a ldev number for LDEV option in your command.
- ACTION
Retype the command and include a ldev number.
- 771
- MESSAGE
EXPECTED 'ldev TO BE WITHIN THE RANGE OF A POSITIVE INTEGER. SYSGEN/STORE INTERFACE ERROR. (S/R 771)
- CAUSE
You have entered an invalid number for LDEV option.
- ACTION
Retype the command and include a valid ldev number.
- 773
- MESSAGE
WARNING: 'REELNUM' OPTION HAS BEEN REDUNDANTLY SPECIFIED. SYSGEN/STORE INTERFACE ERROR. (S/R 773)
- CAUSE
The REELNUM option was entered more than once.
- ACTION
Information only.
- 774
- MESSAGE
'REELNUM' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv. SYSGEN/STORE INTERFACE ERROR. (S/R 774)
- CAUSE
REELNUM and TRANSPORT options are not allowed with the same command line.
- ACTION
TRANSPORT option is not valid with STORE command from SYSGEN. Check the syntax and retype the command.
- 775
- MESSAGE
EXPECTED '=reelnum' AFTER 'REELNUM' OPTION. SYSGEN/STORE INTERFACE ERROR. (S/R 775)
- CAUSE
You have not entered a '=' sign after the REELNUM option in your command.
- ACTION
Retype the command and include '=' sign with your command.
- 776
- MESSAGE
EXPECTED 'REELNUM=reelnum' WHERE reelnum IS A POSITIVE INTEGER. SYSGEN/STORE INTERFACE ERROR. (S/R 776)
- CAUSE
You have not entered any value for REELNUM option in your command.
- ACTION
Retype the command and include a number for REELNUM option.
- 777
- MESSAGE
EXPECTED reelnum TO BE WITHIN THE RANGE OF A POSITIVE INTEGER. SYSGEN/STORE INTERFACE ERROR. (S/R 777)
- CAUSE
You have entered an invalid number for REELNUM option in your comma nd.
- ACTION
Retype the command and include a valid number for REELNUM option.
- 779
- MESSAGE
WARNING: 'SLTDATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. SYSGEN/STORE INTERFACE ERROR. (S/R 779)
- CAUSE
The SLTDATE option was entered more than once.
- ACTION
Information only.
- 780
- MESSAGE
'SLTDATE' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv. SYSGEN/STORE INTERFACE ERROR. (S/R 780)
- CAUSE
SLTDATE and TRANSPORT options are not allowed on the same command line.
- ACTION
TRANSPORT option is invalid when a combined SLT/Store set is created. Delete the TRANSPORT option from your command line.
- 781
- MESSAGE
EXPECTED '=date' AFTER 'SLTDATE' OPTION. SYSGEN/STORE INTERFACE ERROR. (S/R 781)
- CAUSE
You did not include a '=' sign for SLTDATE option.
- ACTION
Retype the command and include a '=' sign for SLTDATE option.
- 782
- MESSAGE
EXPECTED 'SLTDATE=date' WHERE date IS A POSITIVE INTEGER. SYSGEN/STORE INTERFACE ERROR. (S/R 782)
- CAUSE
You did not include a valid number for SLTDATE option.
- ACTION
Check the syntax and include a valid number for SLTDATE opion.
- 783
- MESSAGE
EXPECTED date TO BE WITHIN THE RANGE OF A POSITIVE INTEGER. SYSGEN/STORE INTERFACE ERROR. (S/R 783)
- CAUSE
You did not include a valid number for DATE option.
- ACTION
Check the syntax and include a valid number for DATE option.
- 785
- MESSAGE
WARNING: 'TIME' OPTION HAS BEEN REDUNDANTLY SPECIFIED. SYSGEN/STORE INTERFACE ERROR. (S/R 785)
- CAUSE
The TIME option was entered more than once.
- ACTION
Information only.
- 786
- MESSAGE
'TIME' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv. SYSGEN/STORE INTERFACE ERROR. (S/R 786)
- CAUSE
TIME and TRANSPORT options are not allowed on the same command line.
- ACTION
TRANSPORT option is invalid when combined SLT/Store Set is created. Check your syntax and retype the command.
- 787
- MESSAGE
EXPECTED '=time' AFTER 'TIME' OPTION. SYSGEN/STORE INTERFACE ERROR. (S/R 787)
- CAUSE
You did not include a '=' sign after the TIME option in your command line.
- ACTION
Retype the command and include '=' sign after the TIME option.
- 788
- MESSAGE
EXPECTED 'TIME=time' WHERE time IS A POSITIVE INTEGER. SYSGEN/STORE INTERFACE ERROR. (S/R 788)
- CAUSE
You have not entered a valid number for TIME parameter.
- ACTION
Retype the command and include a valid number for TIME parameter.
- 789
- MESSAGE
EXPECTED time TO BE WITHIN THE RANGE OF A POSITIVE INTEGER. SYSGEN/STORE INTERFACE ERROR. (S/R 789)
- CAUSE
You did not include a valid number for the TIME option.
- ACTION
Check the syntax and enter a valid number for TIME option.
- 791
- MESSAGE
WARNING: 'SYNTAX' OPTION HAS BEEN REDUNDANTLY SPECIFIED. SYSGEN/STORE INTERFACE ERROR. (S/R 791)
- CAUSE
The SYNTAX option was entered more than once.
- ACTION
Information only.
- 792
- MESSAGE
'SYNTAX' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv. SYSGEN/STORE INTERFACE ERROR. (S/R 792)
- CAUSE
SYNTAX and TRANSPORT options are not allowed on the same command line.
- ACTION
TRANSPORT is not valid when creating combined SLT/Store Set tape. Delete TRANSPORT option and retype the command.
- 793
- MESSAGE
WARNING: 'NOLOCK' OPTION HAS BEEN REDUNDANTLY SPECIFIED. SYSGEN/STORE INTERFACE ERROR. (S/R 793)
- CAUSE
The NOLOCK option was entered more than once.
- ACTION
Information only, no action required.
- 794
- MESSAGE
'NOLOCK' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv. SYSGEN/STORE INTERFACE ERROR. (S/R 794)
- CAUSE
NOLOCK and TRANSPORT options are not allowed on the same command line.
- ACTION
Delete either NOLOCK or TRANSPORT option and retype the command.
- 795
- MESSAGE
'NOLOCK' OPTION CANNOT BE USED WITH THE 'ONLINE' OPTION. SYSGEN/STORE INTERFACE ERROR. (S/R 795)
- CAUSE
NOLOCK and ONLINE options are not allowed on the same command line.
- ACTION
Delete either NOLOCK or ONLINE option and retype the command.
- 796
- MESSAGE
'NOLOCK' OPTION CANNOT BE USED WITH THE 'SPLITVS' OPTION. SYSGEN/STORE INTERFACE ERROR. (S/R 796)
- CAUSE
NOLOCK and SPLITVS options are not allowed on the same command line.
- ACTION
Delete either NOLOCK or SPLITVS option and retype the command.
- 797
- MESSAGE
WARNING: 'RENAME' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 797)
- CAUSE
The RENAME option was entered more than once.
- ACTION
Information only.
- 798
- MESSAGE
'RENAME' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 798)
- CAUSE
Specification of RENAME;TRANSPORT; as options to STORE.
- ACTION
Do not use TRANSPORT with RENAME or vice versa. RENAME is only supported on MPE/iX.
- 799
- MESSAGE
'RENAME' OPTION CANNOT BE USED WITH THE 'SPLITVS' OPTION. (S/R 799)
- CAUSE
Specification of RENAME;SPLITVS as options to STORE.
- ACTION
Do not use them together. RENAME is not supported for SPLITVS.
Store/Restore (S/R) 800-899
- 800
- MESSAGE
'RENAME' OPTION CANNOT BE USED WITH THE 'PURGE' OPTION. (S/R 800)
- CAUSE
RENAME and PURGE options are not allowed on the same command line.
- ACTION
Delete either RENAME or PURGE option and retype the command.
- 801
- MESSAGE
SPECIFIED FUNCTION (OPTION) IS NOT IMPLEMENTED ON THIS RELEASE. (S/R 801)
- CAUSE
Same as message content.
- ACTION
Check the syntax and retype the command.
- 802
- MESSAGE
MAXIMUM ALLOWABLE NUMBER OF DEVICE FILE EQUATIONS HAS BEEN EXCEEDED. (S/R 802)
- CAUSE
You specified too many device file equations.
- ACTION
Check the syntax and retype the command.
- 803
- MESSAGE
DEVICE FILE EQUATION NAME EXCEEDS THE MAXIMUM ALLOWED LENGTH. (S/R 803)
- CAUSE
Same as the message content.
- ACTION
Check the syntax and retype the command.
- 804
- MESSAGE
EXPECTED ONE OF: SHOW, ONERROR, LOCAL, GROUP, ACCOUNT, CREATE, CREATOR, GID, KEEP, NOKEEP, OLDDATE, NEWDATE, LISTDIR, DIRECTORY, FCRANGE, FILES, DEV, VOL, VOLCLASS, VOLSET, COPYACD, NOACD, TREE, NOTREE. TURBOSTORE ONLY OPTIONS: RESTORESET, MOSET, NAME. (S/R 804)
- CAUSE
You did not enter a valid option.
- ACTION
Retype the command with valid options.
- 805
- MESSAGE
EXPECTED ONE OF: SHOW, ONERROR, DATES, PURGE, PROGRESS, DIRECTORY, FILES, TRANSPORT, COPYACD, NOACD, MAXTAPEBUF, FCRANGE, NOTIFY, ONVS, SPLITVS, RENAME, TREE, NOTREE. TURBOSTORE ONLY OPTIONS: INTER, ONLINE, STORESET, COMPRESS, MOSET, NAME. (S/R 805)
- CAUSE
You did not enter a valid option.
- ACTION
Retype the command with valid options.
- 806
- MESSAGE
EXPECTED A SEMICOLON ";" TO SEPARATE OPTIONS. (S/R 806)
- CAUSE
You did not include a semicolon in-between the options.
- ACTION
Check the syntax and retype the command.
- 807
- MESSAGE
EXPECTED A SEMICOLON ";" TO SEPARATE THE DEVICE FILE EQUATION (restorefile) AND THE filesetlist.
SYNTAX
'RESTORE [restorefile] [;[filesetlist] [;option[;..]]]' (S/R 807)
- CAUSE
You did not include a semicolon in-between device file equations.
- ACTION
Check the syntax and retype the command.
- 808
- MESSAGE
EXPECTED DEVICE FILE EQUATION (restorefile) TO FOLLOW RESTORE COMMAND WHERE THE DEVICE FILE EQUATION SPECIFIES THE SOURCE DEVICE FROM WHICH THE FILES WILL BE RESTORED.
SYNTAX
'RESTORE [restorefile] [;[filesetlist] [;option[;..]]]' (S/R 808)
- CAUSE
You did not specify device file equation.
- ACTION
Check the syntax and retype the command.
- 809
- MESSAGE
EXPECTED A SEMICOLON ";" TO SEPARATE THE filesetlist FROM THE DEVICE FILE EQUATION (storefile).
SYNTAX
'STORE [filesetlist] [;[storefile] [;option[;..]]]' (S/R 809)
- CAUSE
You did not include a semicolon in between filesetlists.
- ACTION
Check the syntax and retype the command.
- 810
- MESSAGE
EXPECTED A SEMICOLON ";" TO SEPARATE THE DEVICE FILE EQUATION (storefile) FROM THE STORE OPTIONS.
SYNTAX
'STORE [filesetlist] [;[storefile] [;option[;..]]]' (S/R 810)
- CAUSE
You did not include a semicolon in between device file equations.
- ACTION
Check the syntax and retype the command.
- 811
- MESSAGE
EXPECTED DEVICE FILE EQUATION (storefile) TO FOLLOW filesetlist SPECIFICATION, WHERE THE DEVICE FILE EQUATION SPECIFIES THE DESTINATION DEVICE ONTO WHICH THE FILES WILL BE STORED.
SYNTAX
'STORE [filesetlist] [;[storefile] [;option[;..]]]' (S/R 811)
- CAUSE
You did not include a device file equation.
- ACTION
Check the syntax and retype the command.
- 812
- MESSAGE
EXPECTED 'STORE' 'VSTORE' OR 'RESTORE' COMMAND TO BE SPECIFIED.
SYNTAX
'STORE [filesetlist] [;storefile] [;option [; ]]]'
SYNTAX
'RESTORE [restorefile] [;[filesetlist] [;option[;..]]]'
SYNTAX
'VSTORE [vstorefile] [;[filesetlist] [;option[;..]]]'
(S/R 812)- CAUSE
You did not type a valid command.
- ACTION
Retype the command.
- 813
- MESSAGE
ERROR PARSING INDIRECT FILE "!" AT LINE #! (S/R 813)
- CAUSE
Same as message content.
- ACTION
Check you indirect file.
- 814
- MESSAGE
'GROUP' PARAMETER OF THE 'CREATE' OPTION REQUIRES (SM) AND/OR (CV) CAPABILITY TO CREATE GROUPS ON USER VOLUMES. (S/R 814)
- CAUSE
You do not have SM or CV capability.
- ACTION
Log on to an account with either SM or CV capability.
- 815
- MESSAGE
'LDEV' OPTION CANNOT BE USED IN AN INDIRECT FILE. SYSGEN/STORE INTERFACE ERROR. (S/R 815)
- CAUSE
LDEV option is not allowed with STORE command from SYSGEN in an indirect file.
- ACTION
Check the syntax and retype the command.
- 816
- MESSAGE
'REELNUM' OPTION CANNOT BE USED IN AN INDIRECT FILE. SYSGEN/STORE INTERFACE ERROR. (S/R 816)
- CAUSE
REELNUM option is not allowed with the STORE command from SYSGEN in an indirect file.
- ACTION
Check the syntax and retype the command.
- 817
- MESSAGE
'SLTDATE' OPTION CANNOT BE USED IN AN INDIRECT FILE. SYSGEN/STORE INTERFACE ERROR. (S/R 817)
- CAUSE
SLTDATE with STORE command from sysgen in an indirect file.
- ACTION
Check the syntax and retype the command.
- 818
- MESSAGE
'TIME' OPTION CANNOT BE USED IN AN INDIRECT FILE. SYSGEN/STORE INTERFACE ERROR. (S/R 818)
- CAUSE
The option TIME is not allowed with the store command from sysgen in an indirect file.
- ACTION
Check the syntax and retype the command.
- 819
- MESSAGE
'SYNTAX' OPTION CANNOT BE USED IN AN INDIRECT FILE. SYSGEN/STORE INTERFACE ERROR. (S/R 819)
- CAUSE
SYNTAX option is not allowed with store command from SYSGEN in an indirect file.
- ACTION
Check the syntax and retype the command.
- 820
- MESSAGE
SYSGEN OPTIONS NOT ALL SPECIFIED. SYSGEN/STORE INTERFACE ERROR. (S/R 820)
- CAUSE
The options passed by SYSGEN to store command are incomplete.
- ACTION
Internal error.
- 821
- MESSAGE
MAXIMUM NUMBER OF PARALLEL SETS EXCEEDED FOR 'STORESET' OPTION. Ex., 'STORESET =(*ta),(*tb)' IS TWO PARALLEL SETS (S/R 821)
- CAUSE
You have exceeded the maximum number of parallel set allowed for STORESET option, which is 16.
- ACTION
Retype the command and make sure not to exceed 16 parallel sets.
- 822
- MESSAGE
STORING TO A DISK FILE IS NOT AVAILABLE ON YOUR VERSION OF STORE.
- CAUSE
Storing to disc is not available on this version of STORE.
- ACTION
You must purchase TurboSTORE/iX 7x24 True-Online Backup to get this functionality.
Store/Restore (S/R) 900-999
- 901
- MESSAGE
WARNING: 'ONLINE' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 901)
- CAUSE
The ONLINE option was entered more than once.
- ACTION
Information only.
- 902
- MESSAGE
'ONLINE' OPTION CANNOT BE USED WITH THE 'SPLITVS' OPTION (S/R 902)
- CAUSE
ONLINE and SPLITVS options are not allowed on the same command line.
- ACTION
Delete either ONLINE or SPLITVS option and retype the command.
- 903
- MESSAGE
'ONLINE' OPTION CANNOT BE USED WITH THE 'DYNAMIC' OPTION (S/R 903)
- CAUSE
ONLINE and DYNAMIC options are not allowed on the same command line.
- ACTION
Delete either ONLINE or DYNAMIC option and retype the command.
- 904
- MESSAGE
'ONLINE' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv (S/R 904)
- CAUSE
ONLINE and TRANSPORT options are not allowed on the same command line.
- ACTION
CMSTORE and V/E cannot handle ONLINE option. Delete either ONLINE or TRANSPORT option and retype the command.
- 905
- MESSAGE
SHADOW SUBSYSTEM ERROR: TOO MANY ENVIRONMENTS (S/R 905)
- CAUSE
You have exceeded the maximum ONLINE store operation allowed per system which is 16.
- ACTION
Do not run more than 16 store operations with ONLINE option.
- 906
- MESSAGE
SHADOW SUBSYSTEM ERROR: OUT OF DISC SPACE FOR LOG (S/R 906)
- CAUSE
There is not enough disk space to create log files for ONLINE store operation.
- ACTION
Delete some unwanted files in the system and restart the store operation.
- 907
- MESSAGE
SHADOW SUBSYSTEM ERROR: UNEXPECTED ENVIRONMENT ERROR (S/R 907)
- CAUSE
Internal error from ONLINE STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 908
- MESSAGE
SHADOW SUBSYSTEM ERROR: UNEXPECTED TRAP ON ENVIRONMENT (S/R 908)
- CAUSE
Internal error from ONLINE STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 909
- MESSAGE
SHADOW SUBSYSTEM ERROR: OUT OF TRANSIENT DISC SPACE (S/R 909)
- CAUSE
Internal error occurred due to system running out of transient disc space.
- ACTION
Reconfigure the transient disc space using VOLUTIL and retype the command.
- 910
- MESSAGE
SHADOW SUBSYSTEM ERROR: COULD NOT FIND ENVIRONMENT (S/R 910)
- CAUSE
Internal error from ONLINE STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 911
- MESSAGE
SHADOW SUBSYSTEM ERROR: UNKNOWN ERROR ENCOUNTERED (S/R 911)
- CAUSE
Internal error from ONLINE STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 912
- MESSAGE
! NOT STORED: TOO MANY FILES ATTACHED TO SHADOW
- CAUSE
There are too many files attached to this environment. Maximum allowed is 431250.
- ACTION
Delete some files from the list and retype the command.
- 913
- MESSAGE
! NOT STORED: FILE OPEN FOR WRITE AT ATTACH
- CAUSE
This particular file is not stored because it is open for write during store operation.
- ACTION
Close the file and restart the store operation.
- 914
- MESSAGE
! NOT STORED: OPEN AT ATTACH TIME FAILED
- CAUSE
Internal error from online STORE.
- ACTION
Contact your HP Support representative for further information.
- 915
- MESSAGE
! NOT STORED: FILE ALREADY ATTACHED BY A STORE
- CAUSE
This file was not stored because it was already attached by another shadow environment.
- ACTION
Retry the command at a later time.
- 916
- MESSAGE
! NOT STORED: UNEXPECTED SHADOW TRAP ON FILE
- CAUSE
Internal error from online STORE.
- ACTION
Contact your HP Support representative for further information.
- 917
- MESSAGE
! NOT STORED: SHADOW OUT OF DISC LOG SPACE
- CAUSE
This file is not stored because the system did not have enough disc space when logging for this file.
- ACTION
Purge some unwanted files and retype the command again.
- 918
- MESSAGE
! NOT STORED: UNEXPECTED SHADOW ERROR ON FILE
- CAUSE
Internal error from online STORE.
- ACTION
Contact your HP Support representative for further information.
- 919
- MESSAGE
! NOT STORED: OUT OF TRANSIENT DISC SPACE
- CAUSE
This particular file was not stored because the system ran out of transient disc space.
- ACTION
Reconfigure the transient space using VOLUTIL and retype the command.
- 920
- MESSAGE
! NOT STORED: UNEXPECTED TRAP ON ENVIRONMENT
- CAUSE
Internal error during online STORE operation.
- ACTION
Contact your HP Support representative for further assistance.
- 921
- MESSAGE
! NOT STORED: CANT LOCATE SHADOW ENVIRONMENT
- CAUSE
Internal error during online STORE operation.
- ACTION
Contact your HP Support representative for further assistance.
- 922
- MESSAGE
! NOT STORED: UNEXPECTED ERROR ON ENVIRONMENT
- CAUSE
Internal error occured during onlone STORE of this particular file.
- ACTION
Contact your HP Support representative for further information.
- 923
- MESSAGE
! NOT STORED: UNKNOWN SHADOW ERROR ENCOUNTERED
- CAUSE
Internal error occured during online STORE of this particular file.
- ACTION
Contact your HP Support representative for further information.
- 924
- MESSAGE
SHADOW ATTACH ROUTINE ENCOUNTERED ERROR (S/R 924)
- CAUSE
Internal error from online STORE operation.
- ACTION
Contact your HP Support representative for further assistance.
- 925
- MESSAGE
SHADOW DETACH ROUTINE ENCOUNTERED ERROR (S/R 925)
- CAUSE
Internal error occured during online STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 926
- MESSAGE
SHADOW CREATE ROUTINE ENCOUNTERED ERROR (S/R 926)
- CAUSE
Internal error occured during online STORE operation.
- ACTION
Contact your HP Support representative for further assistance.
- 927
- MESSAGE
SHADOW RELEASE ROUTINE ENCOUNTERED ERROR (S/R 927)
- CAUSE
Internal error occurred during online STORE operation.
- ACTION
Contact your HP Support representative for further assistance.
- 928
- MESSAGE
SHADOW GET FILE INFO ROUTINE ENCOUNTERED ERROR (S/R 928)
- CAUSE
Internal error occurred during online STORE opertion.
- ACTION
Contact your HP Support representative for further assistance.
- 929
- MESSAGE
SHADOW GET FILE LOG INFO ROUTINE ENCOUNTERED ERROR (S/R 929)
- CAUSE
Internal error occurred during online STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 930
- MESSAGE
SHADOW GET LOG BLOCK INFO ROUTINE ENCOUNTERED ERROR (S/R 930)
- CAUSE
Internal error occurred during online STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 931
- MESSAGE
SHADOW GET CHANGED UFID ROUTINE ENCOUNTERED ERROR (S/R 931)
- CAUSE
Internal error occurred during online STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 932
- MESSAGE
SHADOW LINKED TO SPOOLING QUEUE ROUTINE ENCOUNTERED ERROR (S/R 932)
- CAUSE
Internal error occurred during online STORE.
- ACTION
Contact your HP Support representative for further assistnace.
- 933
- MESSAGE
SHADOW GET FLABX LENGTH ROUTINE ENCOUNTERED ERROR (S/R 933)
- CAUSE
Internal error occurred during online STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 934
- MESSAGE
SHADOW FLABX READ ROUTINE ENCOUNTERED ERROR (S/R 934)
- CAUSE
Internal error occurred during online STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 935
- MESSAGE
SHADOW UNKNOWN ROUTINE ENCOUNTERED ERROR (S/R 935)
- CAUSE
Internal error occurred during online STORE.
- ACTION
Contact your HP Support representative for further assistance.
- 936
- MESSAGE
SHADOW RETURNED BAD STATUS FROM SUBSYSTEM !, ERROR ! (S/R 936)
- CAUSE
Internal error occurred during online Store.
- ACTION
Contact your HP Support representative.
- 938
- MESSAGE
SQL ONLINE STORE ABORTED BECAUSE OF A REJECTED FILE (S/R 938)
- CAUSE
STORE determined that some of the files specified for the SQL online store would not be able to be stored.
- ACTION
Check the input fileset specification to SQL online store and retype the STORE command.
- 939
- MESSAGE
SQL ONLINE STORE ABORTED BECAUSE OF A FAILED FILE (S/R 939)
- CAUSE
Internal error occurred during SQL Online Store.
- ACTION
Contact your HP Support Representative further assistance.
- 940
- MESSAGE
SQL ONLINE STORE ENCOUNTERED SENDMAIL ERROR ! (S/R 940)
- CAUSE
Internal error occurred during the SQL Online Store.
- ACTION
Contact your HP Support Representative for further assistance.
- 941
- MESSAGE
SHADOW LOG SPACE SUMMARY ROUTINE ENCOUNTERED ERROR (S/R 941)
- CAUSE
Unable to display shadow summary information of the log space due to internal error.
- ACTION
Call your HP Support representative for further assistance.
- 942
- MESSAGE
ONLINE BACKUP UTILIZED DISC SPACE FOR LOG ON THE FOLLOWING VOLSETS:
- CAUSE
Displays the disc space utilized by log file during online backup.
- ACTION
Information only.
- 951
- MESSAGE
'TREE' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv. (S/R 951)
- CAUSE
The 'TREE' and TRANSPORT' options were specfied for a single STORE command. CMSTORE and MPE V cannot handle HFS directories.
- ACTION
Remove either the 'TREE' option or the 'TRANSPORT' option from theSTORE command.
- 952
- MESSAGE
WARNING: 'TREE' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 952)
- CAUSE
The TREE option was entered more than once.
- ACTION
Information only.
- 953
- MESSAGE
'NOTREE' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv. (S/R 953)
- CAUSE
NOTREE and TRANSPORT options are not allowed on the same command line.
- ACTION
CMSTORE and MPE V/E cannot handle HFS directories. Delete NOTREE or TRANSPORT option and retype the command
- 954
- MESSAGE
WARNING: 'NOTREE' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 954)
- CAUSE
The NOTREE option was entered more than once.
- ACTION
Information only.
- 955
- MESSAGE
'TREE' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'NOTREE' OPTION (S/R 955)
- CAUSE
TREE and NOTREE options are not allowed on the same command line.
- ACTION
Delete either TREE or NOTREE option and retype the command.
- 957
- MESSAGE
'NOTIFY' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 957)
- CAUSE
The NOTIFY option cannot be used when creating an MPE/V compatible tape.
- ACTION
Remove either NOTIFY or TRANSPORT from the Store command line and retype your command.
- 958
- MESSAGE
WARNING: 'NOTIFY' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 958)
- CAUSE
You have specified the NOTIFY option more than once on the Store command line.
- ACTION
Information only, but you should remove the extra occurances of the option.
- 961
- MESSAGE
'PARTIALDB' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 961)
- CAUSE
The PARTIALDB option cannot be used to create MPEv media.
- ACTION
Delete one of the two options and re-run the command.
- 962
- MESSAGE
'PARTIALDB' OPTION CANNOT BE USED WITH 'LISTDIR' OPTION (S/R 962)
- CAUSE
The PARTIALDB and the LISTDIR option cannot be specified for the same RESTORE.
- ACTION
Delete one of the two options from the RESTORE command line.
- 963
- MESSAGE
WARNING: 'PARTIALDB' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 963)
- CAUSE
The PARTIALDB command was specified more than once on the command line.
- ACTION
Information only.
- 964
- MESSAGE
WARNING: 'NOSTOREDIRECTORY' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 964)
- CAUSE
The NOSTOREDIRECTORY command was specified more than once on the command line.
- ACTION
Information only.
- 965
- MESSAGE
'GID' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 965)
- CAUSE
The GID option was entered more than once.
- ACTION
Information only.
- 966
- MESSAGE
EXPECTED '=fgroup' AFTER 'GID' OPTION WHERE fgroup IS THE NAME OF "FILE GROUP" WHICH SHARES THIS FILE. THE FILES WILL BE RESTORED SUCH THAT THE SPECIFIED FILE GROUP WILL BE THE NEW FILE SHARING ATTRIBUTE OF THE FILES.
SYNTAX
'GID[=fgroup]' WHERE 'GID' WITH NO "=fgroup" SPECIFIED DEFAULTS TO PRESERVING THE ORIGNAL GID OF THE FILE (S/R 966)
- CAUSE
You have not included a '=' sign after GID option in your command line.
- ACTION
Retype the command and include a '=' sign after the GID option.
- 967
- MESSAGE
EXPECTED 'fgroup' TO BE SPECIFIED FOR 'GID' OPTION. A fgroup NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH.
SYNTAX
'GID[=fgroup]' WHERE 'GID' WITH NO "=fgroup" SPECIFIED DEFAULTS TO PRESERVING THE ORIGNAL GID OF THE FILE (S/R 967)
- CAUSE
You have specified an invalid 'fgroup' for GID option in your command line.
- ACTION
Retype the command and include a valid 'fgroup' name for GID option.
- 968
- MESSAGE
'GID' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 968)
- CAUSE
GID and LISTDIR options are not allowed on the same command line.
- ACTION
Delete either LISTDIR or GID option and retype the command.
- 969
- MESSAGE
WARNING: 'HFSWARN' OPTION IS NO LONGER SUPPORTED. PLEASE REMOVE THIS OPTION FROM BACKUP PROCEDURES. OPTION IGNORED. (S/R 969)
- CAUSE
You are specifying the HFSWARN option to store. This option is no longer supported or needed.
- ACTION
Remove the HFSWARN option from any STORE job streams.
- 970
- MESSAGE
WARNING: 'NOHFSWARN' OPTION IS NO LONGER SUPPORTED. PLEASE REMOVE THIS OPTION FROM BACKUP PROCEDURES. OPTION IGNORED. (S/R 970)
- CAUSE
You are specifying the NOHFSWARN option to store. This option is no longer supported or needed.
- ACTION
Remove the NOHFSWARN option from any STORE job streams.
- 971
- MESSAGE
'TRANSPORT' OPTION CANNOT BE USED WITH THE 'TRANSPORT=MPEXL' OPTION. (S/R 971)
- CAUSE
TRANSPORT and TRANSPORT=MPEXL options are not allowed on the same command line.
- ACTION
Delete one of the options and retype the command.
- 972
- MESSAGE
'TRANSPORT=MPEXL' OPTION CANNOT BE USED WITH THE 'TRANSPORT' OPTION. (S/R 972)
- CAUSE
TRANSPORT=MPEXL and TRANSPORT options are not allowed on the same command line.
- ACTION
Delete one of the options and retype the command.
- 973
- MESSAGE
WARNING: 'TRANSPORT=MPEXL' OPTION HAS BEEN REDUNDANDLY SPECIFIED (S/R 973)
- CAUSE
You have entered TRANSPORT=MPEXL twice.
- ACTION
Information only, no action required.
- 974
- MESSAGE
'NOHFSWARN' OPTION CANNOT BE USED WITH THE 'HFSWARN' OPTION (S/R 974)
- CAUSE
The NOHFSWARN and HFSWARN options cannot be used together. However, neither option is supported any more.
- ACTION
Remove any NOHFSWARN or HFSWARN options from your STORE commands.
- 976
- MESSAGE
EXPECTED 'onlineparm[,onlineparm..]' AFTER 'ONLINE=' option where ''onlineparm IS 'START' OR 'END', OPTIONALLY BE FOLLOWED BY time (hh:mm:ss) or A SK (S/R 976)''
- CAUSE
'ONLINE =' option must be followed by START or END options.
- ACTION
Check your command line and specify START or END for 'ONLINE=' option.
- 977
- MESSAGE
'ONLINE=END' OPTION CANNOT BE USED WITH 'ONLINE' OPTION (S/R 977)
- CAUSE
You cannot specify both ONLINE and ONLINE=END.
- ACTION
Decide what type of online backup you want to perform, then specify either ONLINE or ONLINE=END.
- 978
- MESSAGE
'ONLINE=END' OPTION CANNOT BE USED WITH 'ONLINE=START' OPTION (S/R 978)
- CAUSE
You cannot specify both START and END sync points.
- ACTION
Remove one of the ONLINE options and re-run the command.
- 979
- MESSAGE
WARNING: 'ONLINE=END' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R979)
- CAUSE
You have specified the ONLINE=END option more than once.
- ACTION
Information only.
- 980
- MESSAGE
'ONLINE=START' OPTION CANNOT BE USED WITH 'ONLINE' OPTION (S/R 980)
- CAUSE
You cannot use the ONLINE option with the ONLINE=START option.
- ACTION
Remove one of the ONLINE options and re-run the command.
- 981
- MESSAGE
WARNING: 'ONLINE=START' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 981)
- CAUSE
You have specified the ONLINE=START option more than once.
- ACTION
Information only.
- 982
- MESSAGE
SYNC TIME MUST BE USED WITH 'START' OR 'END' PARAMETERS (S/R 982)
- CAUSE
You must specify ONLINE=START or ONLINE=END if you specify a time parameter to ONLINE.
- ACTION
Either remove the time specification or add START or END to the ONLINE option.
- 983
- MESSAGE
'ONLINE=time' OPTION CANNOT BE USED WITH 'ONLINE' OPTION (S/R 983)
- CAUSE
You cannot specify ONLINE=time and ONLINE in the same command.
- ACTION
Remove one of the ONLINE options and re-run the command.
- 984
- MESSAGE
MULTIPLE SYNC TIMES CAN NOT BE SPECIFIED (S/R 984)
- CAUSE
Only one time can be specified for the online sync point.
- ACTION
Remove all but one of the times and re-run the command.
- 985
- MESSAGE
INVALID TIME SPECIFIED, MUST BE SPECIFIED AS HH:MM[:SS] (e.g. 14:30:30) (S/R 985)
- CAUSE
You specified the online sync time incorrectly.
- ACTION
Specify the time as HH:MM[:SS] and re-run the command.
- 986
- MESSAGE
'STOREDIRECTORY' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 986)
- CAUSE
The STOREDIRECTORY option cannot be used to create MPEv media.
- ACTION
Delete one of the two options and re-run the command.
- 987
- MESSAGE
'STOREDIRECTORY' OPTION CANNOT BE USED WITH 'NOSTOREDIRECTORY' OPTION (S/R 987)
- CAUSE
You cannot specify both STOREDIRECTORY and NOSTOREDIRECTORY.
- ACTION
Remove one of the options and re-run the command.
- 988
- MESSAGE
WARNING: 'STOREDIRECTORY' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 988)
- CAUSE
You have specified the STOREDIRECTORY option more than once.
- ACTION
Information only.
- 989
- MESSAGE
EXPECTED '=directoryname' AFTER 'STOREDIRECTORY' OPTION.
SYNTAX
'STOREDIR[ECTORY]=directoryname' (S/R 989)
- CAUSE
No filename was specified after the STOREDIRECTORY option.
- ACTION
Specify a valid MPE or HFS-style file name of the file that contains the store disk directory for this backup and re-run the command.
- 990
- MESSAGE
INVALID FILENAME FOR STOREDIRECTORY (S/R 990)
- CAUSE
An invalid name was specified for the STOREDIRECTORY option.
- ACTION
Specify a valid MPE or HFS filename.
- 991
- MESSAGE
'LOGVOLSET' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R991)
- CAUSE
The LOGVOLSET option cannot be used to create MPEv media.
- ACTION
Remove one of the options and re-run the command.
- 992
- MESSAGE
WARNING: 'LOGVOLSET' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 992)
- CAUSE
The LOGVOLSET option was specified more than once.
- ACTION
Information only.
- 993
- MESSAGE
EXPECTED '=volumesetname' AFTER 'LOGVOLSET' OPTION.
SYNTAX
'LOGVOLSET=volumesetname' (S/R 993)
- CAUSE
The name of a valid volume set was not specified after the LOGVOLSET option.
- ACTION
Check your command line and specify a valid volume set for the LOGVOLSET option.
- 994
- MESSAGE
'NOSTOREDIRECTORY' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 994)
- CAUSE
The NOSTOREDIRECTORY option cannot be used to create MPEv media.
- ACTION
Remove one of the options and re-run the command.
- 998
- MESSAGE
STORE DIRECTORY FILENAMES MAY NOT BE HFS DIRECTORIES (S/R 998)
- CAUSE
The file specified for the STOREDIRECTORY option was an HFS directory.
- ACTION
Specify a non-HFS directory filename for the STOREDIRECTORY option.
- 999
- MESSAGE
INDIRECT FILENAMES MAY NOT BE HFS DIRECTORIES (S/R 999)
- CAUSE
An HFS directory was specified as an indirect file.
- ACTION
Specify a non-HFS directory file for a STORE indirect file.
Store/Restore (S/R) 1000-1199
- 1000
- MESSAGE
STORE DIRECTORY FILENAMES MAY NOT BE WILDCARDED (S/R 1000)
- CAUSE
A wildcard was specified as an indirect file.
- ACTION
Specify one indirect file at a time on the STORE command line.
- 1001
- MESSAGE
INDIRECT FILENAMES MAY NOT BE WILDCARDED. (S/R 1001)
- CAUSE
You cannot include wildcard characters in the indirect filename.
- ACTION
Retype the command and enter a valid filename.
- 1002
- MESSAGE
FILE NAME PART LENGTH TOO LONG. A WILDCARDED NAME PART CANNOT EXCEED 8 LOGICAL CHARACTERS, WHERE A LOGICAL CHARACTER IS ONE OF @, #, ?, a-z, 0-9, OR A CHARACTER SET '[]' (S/R 1002)
- CAUSE
You included an invalid filename.
- ACTION
Retype the command and enter a valid filename.
- 1003
- MESSAGE
FILE NAME PART LENGTH TOO LONG. A NAME PART CANNOT EXCEED 8 CHARACTERS IN LENGTH (S/R 1003)
- CAUSE
Same as message content.
- ACTION
Retype the command and include a valid file name.
- 1004
- MESSAGE
EXPECTED A ',' OR ';' TO DELIMIT A FILESET. FILESET NAMES MAY BE COMPOSED OF A MAXIMUM OF THREE PARTS, FILENAME.GROUPNAME.ACCOUNTNAME. (S/R 1004)
- CAUSE
You did not include a comma or semicolon.
- ACTION
Check the syntax and retype the command.
- 1005
- MESSAGE
NEGATIVE FILESETS (FILE EXCLUSION) CANNOT BE USED WITH INDIRECT FILES. (S/R 1005)
- CAUSE
Same as message content.
- ACTION
Retype the command with valid files.
- 1007
- MESSAGE
IF NEGATIVE (EXCLUSION) FILESETS ARE BEING USED, THE FIRST (PRIMARY) FILESET MUST BE WILDCARDED OR RECURSIVE. (S/R 1007)
- CAUSE
You must include a wildcard character in your file set to exclude afile set.
- ACTION
Retype the command using a wildcard character in your file set.
- 1008
- MESSAGE
SLASH "/" TO SPECIFY A LOCKWORD MAY ONLY BE SUPPLIED AFTER THE FILE NAME PART OF A FILESET NAME.
SYNTAX
'FNAME/LOCKWORD[.GNAME[.ANAME]]' (S/R 1008)
- CAUSE
You did not type the lockword correctly.
- ACTION
Check the syntax and retype the command.
- 1009
- MESSAGE
INVALID CHARACTER(S) IN LOCKWORD. LOCKWORD MUST BE ALPHANUMERIC BEGINNING WITH 'A-Z' AND BE NO MORE THAN 8 CHARACTERS IN LENGTH. (S/R 1009)
- CAUSE
You did not enter a valid lockword.
- ACTION
Retype the command with a valid lockword.
- 1010
- MESSAGE
UNMATCHED OPEN BRACKET '[' ENCOUNTERED IN WILDCARED FILE NAME. BRACKETS ARE USED FOR CHARACTER SET WILDCARDING. THEY MAY NOT BE NESTED. (S/R 1010)
- CAUSE
You entered the bracket incorrectly.
- ACTION
Check the syntax and retype the command.
- 1011
- MESSAGE
UNMATCHED CLOSED BRACKET ']' ENCOUNTERED IN WILDCARED FILE NAME. BRACKETS ARE USED FOR CHARACTER SET WILDCARDING. THEY MAY NOT BE NESTED. (S/R 1011)
- CAUSE
You entered the bracket incorrectly.
- ACTION
Check the syntax and retype the command.
- 1012
- MESSAGE
EXPECTED A '.', '/', ',', OR ';' TO FOLLOW THE FILE NAME PART OF A FILESET. '.' SPECIFIES A GROUP NAME PART IS TO FOLLOW, '/' SPECIFIES A LOCKWORD IS TO FOLLOW, ',' SEPARATES THIS FILESET FROM THE NEXT, AND ';' SPECIFIES THE END OF THE FILESETLIST.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1012)
- CAUSE
You entered the file name syntax incorrectly.
- ACTION
Check the syntax and retype the command.
- 1013
- MESSAGE
EXPECTED A '.', ',', OR ';' TO FOLLOW THE GROUP NAME PART OF A FILESET. '.' SPECIFIES A GROUP NAME PART IS TO FOLLOW, ',' SEPARATES THIS FILESET FROM THE NEXT, AND ';' SPECIFIES THE END OF THE FILESETLIST.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1013)
- CAUSE
You did not include a '.', ',', or ';' after the group name.
- ACTION
Check the syntax and retype the command.
- 1014
- MESSAGE
EXPECTED A ',', OR ';' TO FOLLOW THE ACCOUNT NAME PART OF A FILESET. ',' SEPARATES THIS FILESET FROM THE NEXT, AND ';' SPECIFIES THE END OF THE FILESETLIST.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1014)
- CAUSE
You did not include a ',', or ';' after account name.
- ACTION
Check the syntax and retype the command.
- 1015
- MESSAGE
EXPECTED A FILE NAME PART NOT A "-". A "-" IS USED TO SPECIFY NEGATIVE (EXCLUSION) FILESETS.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1015)
- CAUSE
You did not type the file name.
- ACTION
Enter a valid file name.
- 1016
- MESSAGE
EXPECTED A GROUP NAME PART TO FOLLOW 'fname[/lockword].' INSTEAD OF A "-". A "-" IS USED TO SPECIFY NEGATIVE (EXCLUSION) FILESETS.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1016)
- CAUSE
You did not type the group name.
- ACTION
Enter a valid group name.
- 1017
- MESSAGE
EXPECTED AN ACCOUNT NAME PART TO FOLLOW 'fname[/lockword].gname.', NOT A "-". A "-" IS USED TO SPECIFY NEGATIVE (EXCLUSION) FILESETS.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1017)
- CAUSE
You did not type the account name.
- ACTION
Enter a valid account name.
- 1018
- MESSAGE
EXPECTED A FILE NAME PART NOT A "/". A "/" IS USED TO SPECIFY A LOCKWORD AFTER THE FILE NAME PART.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1018)
- CAUSE
You did not type the file name.
- ACTION
Enter a valid file name.
- 1019
- MESSAGE
EXPECTED A GROUP NAME PART TO FOLLOW 'fname[/lockword].' NOT A "/". A "/" IS USED TO SPECIFY A LOCKWORD AFTER THE FILE NAME PART.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1019)
- CAUSE
You did not type the group name.
- ACTION
Enter a valid group name.
- 1020
- MESSAGE
EXPECTED AN ACCOUNT NAME PART TO FOLLOW 'fname[/lockword].gname', NOT A "/". A "/" IS USED TO SPECIFY A LOCKWORD AFTER THE FILE NAME PART.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1020)
- CAUSE
You did not type the account name.
- ACTION
Enter a valid account name.
- 1021
- MESSAGE
EXPECTED A '.', ',', OR ';' TO FOLLOW THE LOCKWORD PART OF A FILESET. '.' SPECIFIES A GROUP NAME PART IS TO FOLLOW, ',' SEPARATES THIS FILESET FROM THE NEXT, AND ';' SPECIFIES THE END OF THE FILESETLIST.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1021)
- CAUSE
You did not include a '.', ',', or ';' after lockword.
- ACTION
Check the syntax and retype the command.
- 1022
- MESSAGE
LOCKWORDS ARE NOT ALLOWED IN NEGATIVE (EXCLUSION) FILESETS.
SYNTAX
'fname[.gname[.aname]]' (S/R 1022)
- CAUSE
Same as message content.
- ACTION
Do not use lockwords with negative filesets.
- 1023
- MESSAGE
SPECIFIED LOCKWORD IS TOO LONG. THE MAXIMUM LENGTH OF A LOCKWORD IS 8 CHARACTERS.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1023)
- CAUSE
The maximum lockword length has been exceeded.
- ACTION
Enter a lockword with 8 characters or less.
- 1024
- MESSAGE
INDIRECT FILES MAY NOT BE USED IN NEGATIVE (EXCLUSION) FILESETS.
SYNTAX
'fname[/lockword][.gname[.aname]][-fname[.gname[.aname]]...' (S/R 1024)
- CAUSE
Same as message content.
- ACTION
Check the syntax and retype the command.
- 1025
- MESSAGE
EXPECTED A FILENAME OF AN INDIRECT FILE TO FOLLOW A '^' OR '!', NOT ANOTHER '^' OR '!'.
NOTE: THE CI USES '!' FOR VARIABLE SUBSITUTION SO USE OF '!' SHOULD BE AVOIDED IN FAVOR OF '^'.SYNTAX
'[^]fname[.gname[.aname]]' (S/R 1025)
- CAUSE
You did not type the indirect file name correctly.
- ACTION
Check the syntax and retype the command.
- 1026
- MESSAGE
EXPECTED A GROUP NAME PART TO FOLLOW 'fname[/lockword].', NOT A '^' OR '!'. A '^' OR '!' IS USED TO SPECIFY AN INDIRECT FILE.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1026)
- CAUSE
'^' or '!' is not accepted after filename.
- ACTION
Check the syntax and retype the command.
- 1027
- MESSAGE
EXPECTED AN ACCOUNT NAME PART TO FOLLOW 'fname[/lockword].gname.', NOT A '^' OR '!'. A '^' OR '!' IS USED TO SPECIFY AN INDIRECT FILE.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1027)
- CAUSE
'^' Or '!' is not accepted after filename.groupname.
- ACTION
Check the syntax and retype the command.
- 1028
- MESSAGE
EXPECTED A FILESET NAME. EMPTY FILESET NAMES ARE NOT ALLOWED UNLESS THEY ARE USED SINGLY TO REQUEST THE DEFAULT FILESET. Ex. 'STORE ;*t;SHOW'.
SYNTAX
'fname[.gname[.aname]]' (S/R 1028)
- CAUSE
You did not type the fileset name correctly.
- ACTION
Check the syntax and retype the command.
- 1029
- MESSAGE
EXPECTED A GROUP NAME PART TO FOLLOW 'fname[/lockword].' INSTEAD OF A ",", ";" OR END OF DATA.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1029)
- CAUSE
You did not type a valid group name after file name.
- ACTION
Check the syntax and retype the command.
- 1030
- MESSAGE
EXPECTED AN ACCOUNT NAME PART TO FOLLOW 'fname[/lockword].gname,', NOT A ",", ";" OR END OF DATA.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1030)
- CAUSE
You did not type a valid account after the group name.
- ACTION
Check the syntax and retype the command.
- 1031
- MESSAGE
A FILESET NAME PART MUST START WITH A-Z OR ANY WILDCARD THAT SPECIFIES A SUBSET OF A-Z ('?', '@', OR A CHARACTER SET). THE REST OF THE CHARACTERS MUST BE ALPHANUMERIC OR WILDCARDS.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1031)
- CAUSE
You probably mistyped the file name.
- ACTION
Retype the command.
- 1032
- MESSAGE
EXPECTED A FILE NAME PART NOT A ".". A "." IS USED TO SEPARATE PARTS OF A FILENAME.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1032)
- CAUSE
You did not type the file name correctly.
- ACTION
Check the syntax and retype the command.
- 1033
- MESSAGE
EXPECTED A GROUP NAME PART TO FOLLOW 'fname[/lockword].' NOT A ".". A "." IS USED TO SEPARATE PARTS OF A FILENAME.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1033)
- CAUSE
You did not type the group name correctly.
- ACTION
Retype the command with a valid group name.
- 1034
- MESSAGE
EXPECTED AN ACCOUNT NAME PART TO FOLLOW 'fname[/lockword].gname', NOT A ".". A "." IS USED TO SEPARATE PARTS OF A FILENAME.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1034)
- CAUSE
You did not type the account name correctly.
- ACTION
Retype the command with a valid account name.
- 1035
- MESSAGE
INVALID CHARACTER IN FILESET NAME PART. A FILESET NAME PART MUST START WITH A-Z OR ANY WILDCARD THAT SPECIFIES A SUBSET OF A-Z ('?', '@', OR A CHARACTER SET). THE REST OF THE CHARACTERS MUST BE ALPHANUMERIC OR WILDCARDS.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1035)
- CAUSE
You probably mistyped the name of the file set.
- ACTION
Retype the command.
- 1036
- MESSAGE
USER EXCEEDED MAXIMUM INDIRECT FILE NESTING LEVEL. (S/R 1036)
- CAUSE
Same as the message content.
- ACTION
Reduce the indirect file nesting level.
- 1037
- MESSAGE
STORE/RESTORE WAS UNABLE TO OPEN INDIRECT FILE. (S/R 1037)
- CAUSE
Various problems an causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1038
- MESSAGE
INDIRECT FILE RECORD SIZE IS INVALID. IT MUST BE BETWEEN 8 AND 1024 BYTES. (S/R 1038)
- CAUSE
Same as the message content.
- ACTION
Rebuild the indirect file.
- 1039
- MESSAGE
STORE/RESTORE COULD NOT OBTAIN READ ACCESS TO INDIRECT FILE. (S/R 1039)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1040
- MESSAGE
STORE/RESTORE ENCOUNTERED ERROR REWINDING INDIRECT FILE. (S/R 1040)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1041
- MESSAGE
STORE/RESTORE ENCOUNTERED ERROR READING INDIRECT FILE. (S/R 1041)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1042
- MESSAGE
STORE/RESTORE WAS UNABLE TO CLOSE INDIRECT FILE (S/R 1042)
- CAUSE
Various problems and causes.
- ACTION
Call your support representative.
- 1043
- MESSAGE
! NOT STORED: FILE NOT FOUND IN DIRECTORY
- CAUSE
The file does not exist on the system.
- ACTION
Specify another file.
- 1044
- MESSAGE
! NOT STORED: DIRECTORY NODE IN PATH SUFFERED MAP IN FAILURE. NODE PROBABLY HAS EXTENTS ON UNMOUNTED VOLUME
- CAUSE
Various problems and causes.
- ACTION
Call your support representative.
- 1045
- MESSAGE
! NOT STORED: VOLUMESET SPECIFIED IN DIRECTORY PATH DOES NOT EXIST ON THIS SYSTEM
- CAUSE
Same as the message content.
- ACTION
Specify another volumeset.
- 1046
- MESSAGE
! NOT STORED: SPECIFIED ACCOUNT DOES NOT EXIST
- CAUSE
Same as the message content.
- ACTION
Specify another account.
- 1047
- MESSAGE
! NOT STORED: SPECIFIED GROUP DOES NOT EXIST
- CAUSE
Same as the message content.
- ACTION
Specify another group.
- 1048
- MESSAGE
! NOT STORED: SPECIFIED FILE DOES NOT EXIST
- CAUSE
Same as the message content.
- ACTION
Specify another file.
- 1049
- MESSAGE
! NOT STORED: ACCOUNT DOES NOT EXIST ON VOLUMESET SPECIFIED IN DIRECTORY PATH
- CAUSE
Same as the message content.
- ACTION
Specify another account.
- 1050
- MESSAGE
! NOT STORED: GROUP DOES NOT EXIST ON VOLUMESET SPECIFIED IN DIRECTORY PATH
- CAUSE
Same as the message content.
- ACTION
Specify another group.
- 1051
- MESSAGE
! NOT STORED: ERROR IN DIRECTORY SEARCH (FIND) ROUTINE.
- CAUSE
Various problems and causes.
- ACTION
Call your support representative.
- 1052
- MESSAGE
CATASTROPHIC DIRECTORY ERROR. ROOT NODE OPEN FAILURE. (S/R 1052)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1053
- MESSAGE
! SEARCH PATH ENCOUNTERED A DIRECTORY NODE THAT SUFFERED MAP IN FAILURE. SOME FILES WILL NOT BE STORED. NODE PROBABLY HAS EXTENTS ON UNMOUNTED VOLUME. (S/R 1053)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1054
- MESSAGE
! SEARCH PATH ENCOUNTERED A DIRECTORY NODE THAT SUFFERED INTERNAL ACCESS ERROR. SOME FILES WILL NOT BE STORED. (S/R 1054)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1055
- MESSAGE
! NOT STORED: NO MATCHING FILES FOUND
- CAUSE
The files do not exist on the system.
- ACTION
Specify other files.
- 1056
- MESSAGE
! NOT RESTORED: FILE NOT FOUND ON MEDIA
- CAUSE
The files do not exist on the tape.
- ACTION
Specify other files.
- 1057
- MESSAGE
! NOT RESTORED: NO MATCHING FILES FOUND ON MEDIA
- CAUSE
The files do not exist on the tape.
- ACTION
Specify other files.
- 1059
- MESSAGE
SPECIFIED DATA BASE ROOT FILE NAME IS TOO LONG. IT MUST BE SIX CHARACTERS OR LESS TO BE A VALID ROOT FILE NAME. (S/R 1059)
- CAUSE
You specified a data base root file name that was more than six characters.
- ACTION
Enter a data base root file name that has six characters or less.
- 1060
- MESSAGE
INVALID SYNTAX IN CHARACTER SET WILDCARDING. (S/R 1060)
- CAUSE
You included some invalid character.
- ACTION
Retype the command.
- 1061
- MESSAGE
EXCLUSION FILESETS MAY NOT BE USED AS PARTS OF REDIRECTION FILESETS. EXCLUSION CAN ONLY BE PART OF THE ORIGINAL FILESET.
SYNTAX
'fname[/lockword][.gname[.aname][-..][=fname[..][:creator]]' (S/R 1061)
- CAUSE
You cannot use exclusion filesets as parts of your target filesets in RENAME option.
- ACTION
Put exclusion fileset before redirection file name and retype the command.
- 1062
- MESSAGE
INDIRECT FILES MAY NOT BE USED AS (REDIRECTION) FILESETS.
SYNTAX
'fname[/lockword][.gname[.aname][=fname[..][:creator]]' (S/R 1062)
- CAUSE
INdirect files are not allowed in target fileset name in RENAME option.
- ACTION
Check the syntax and retype the command.
- 1063
- MESSAGE
EXPECTED A FILE NAME PART NOT A "=". A "=" IS USED TO INDICATE NAME REDIRECTION.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1063)
- CAUSE
You have not entered a filename before the '=' sign for RENAME option.
- ACTION
Retype the command and include a filename.
- 1064
- MESSAGE
EXPECTED A GROUP NAME PART TO FOLLOW 'fname[/lockword].' NOT A "=". A "=" IS USED TO INDICATE NAME REDIRECTION.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1064)
- CAUSE
You have not entered a group name after the 'fname.' for RENAME option.
- ACTION
Retype the command and enter a group name after 'fname.'.
- 1065
- MESSAGE
EXPECTED AN ACCOUNT NAME PART TO FOLLOW 'fname[/lkwd].gname.' "=". A "=" IS USED TO INDICATE NAME REDIRECTION.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1065)
- CAUSE
You have not entered an account name after 'gname.' for RENAME option.
- ACTION
Retype the command and include a account name after 'gname.'.
- 1066
- MESSAGE
REDIRECTION FILESETS (NAME REDIRECTION) CANNOT BE USED WITH INDIRECT FILES (S/R 1066)
- CAUSE
Target fileset cannot be used with indircet files for RENAME option.
- ACTION
Check the syntax and retype the command.
- 1067
- MESSAGE
ONLY ONE REDIRECTION CAN BE SPECIFIED PER FILESET. (S/R 1067)
- CAUSE
You have specified more than one new filename specification for a file, using the = syntax and the RENAME option.
- ACTION
Check the syntax of your command, only specifying one target name per fileset, and redo the store command.
- 1068
- MESSAGE
EXPECTED A FILE NAME PART NOT A ":". A ":" IS USED TO INDICATE CREATOR NAME REDIRECTION.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1068)
- CAUSE
You have not entered a filename for RENAME option.
- ACTION
Check the syntax and retype the command.
- 1069
- MESSAGE
EXPECTED A GROUP NAME PART TO FOLLOW 'fname[/lockword].' NOT A ":". A ":" IS USED TO INDICATE CREATOR NAME REDIRECTION.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1069)
- CAUSE
You have not entered a group name after 'fname.' for RENAME option.
- ACTION
Check the syntax and retype the command.
- 1070
- MESSAGE
EXPECTED AN ACCOUNT NAME PART TO FOLLOW 'fname[/lkwd].gname.' ":". A ":" IS USED TO INDICATE CREATOR NAME REDIRECTION.
SYNTAX
'fname[/lockword][.gname[.aname]]' (S/R 1070)
- CAUSE
You have not entered an account name after 'gname.'
- ACTION
Check the syntax and retype the command.
- 1071
- MESSAGE
A ':' IS USED TO INDICATE CREATOR NAME REDIRECTION AND CAN ONLY BE USED IN CONJUNCTION WITH FILE '=' REDIRECTION.
SYNTAX
'fname[/lockword][.gname[.aname][=fname[..][:creator]]
- CAUSE
Misuse of colon.
- ACTION
Only use colon with RENAME to specify a new creator.
- 1072
- MESSAGE
EXPECTED A ',', OR ';' TO FOLLOW THE CREATOR NAME PART OF A FILESET. ',' SEPARATES THIS FILESET FROM THE NEXT, AND ';' SPECIFIES THE END OF THE FILESETLIST.
SYNTAX
'fname[/lockword][.gname[.aname][=fname[..][:creator]] (S/R 1072)
- CAUSE
Invalid character as a seperator following creator name.
- ACTION
Check the syntax and retype the command.
- 1073
- MESSAGE
INVALID CHARACTER(S) IN CREATOR NAME. CREATOR NAME MUST BE ALPHANUMERIC BEGINNING WITH 'A-Z' AND BE NO MORE THAN 8 CHARACTERS IN LENGTH (S/R 1073)
- CAUSE
You have entered an invalid creator name.
- ACTION
Check the syntax and retype the command.
- 1074
- MESSAGE
SPECIFIED CREATOR NAME IS TOO LONG. THE MAXIMUM LENGTH OF A CREATOR NAME IS 8 CHARACTERS.
SYNTAX
'fname[/lockword][.gname[.aname][=fname[..][:creator]] (S/R 1074)
- CAUSE
You have entered an invalid creator name.
- ACTION
Check the syntax and retype the command.
- 1075
- MESSAGE
THE ONLY VALID WILDCARD NAME FOR A REDIRECTION FILE NAME PART IS '@'. E.G. A@.B.C=@.D (S/R 1075)
- CAUSE
Trying to use regular store wildcarding.
- ACTION
RENAME does not allow the mixing of wild cards and alphanumeric characters in a target file name.
- 1076
- MESSAGE
REDIRECTION FILE NAMES CAN NOT CONTAIN LOCKWORDS.
SYNTAX
'fname[/lockword][..]=fname[.gname[.accname][:creator]] (S/R 1076)
- CAUSE
Lockwords are not allowed with the redirection file when a RENAME option is specified.
- ACTION
Delete the lockwork and retype the command.
- 1079
- MESSAGE
A REDIRECTION FILE NAME MAY END IN A SLASH OR HAVE WILDCARDS BUT NOT BOTH E.G. /A/G/F@=/D/E/F/ OR /A/G/F@=/D/@/@ (S/R 1079)
- CAUSE
The redirection file name specified a directory with trailing slash. Directories cannot be wildcarded.
- ACTION
Either remove trailing slash or all wildcards.
- 1080
- MESSAGE
THE ONLY VALID WILDCARD NAME FOR A REDIRECTION CREATOR NAME PART IS '@'. E.G. A@.B.C=@.D:U.@ OR A@.B.C=@.D:@.A (S/R 1080)
- CAUSE
Invalid wildcard specification in creator name.
- ACTION
Use a single '@' in creator name and/or creator account name.
- 1081
- MESSAGE
! NOT STORED: FILE NOT FOUND
- CAUSE
A file that was specified to be stored was not found on the system.
- ACTION
Check your input fileset and retype the STORE command.
Store/Restore (S/R) 1200-1399
- 1201
- MESSAGE
VOLUMESET "!" SPECIFIED IN THE 'VOLSET' OPTION DOES NOT EXIST ON THE SYSTEM. (S/R 1201)
- CAUSE
Same as the message content.
- ACTION
Specify another volumeset.
- 1202
- MESSAGE
VOLUME CLASS "!" SPECIFIED IN THE 'VOLCLASS' OPTION DOES NOT EXIST ON THE SPECIFIED VOLUMESET. "MPEXL_SYSTEM_VOLUME_SET" IS THE DEFAULT VOLUME_SET IF NONE WAS SPECIFIED (S/R 1202)
- CAUSE
Same as the message content.
- ACTION
Specify another volume class.
- 1203
- MESSAGE
VOLUME "!" SPECIFIED IN THE 'VOL' OPTION DOES NOT EXIST ON THE SPECIFIED VOLUME_SET. "MPEXL_SYSTEM_VOLUME_SET" IS THE DEFAULT VOLUME_SET IF NONE WAS SPECIFIED. (S/R 1203)
- CAUSE
Same as the message content.
- ACTION
Specify another volume.
- 1204
- MESSAGE
SPECIFIED LDEV IS NOT MOUNTED AT THIS TIME (S/R 1204)
- CAUSE
You specified a device that is not mounted.
- ACTION
Specify a mounted device.
- 1205
- MESSAGE
VOLUME CLASS "!" SPECIFIED IN THE 'VOLCLASS' OPTION DOES NOT CURRENTLY HAVE ANY MEMBER VOLUMES MOUNTED ON THE SYSTEM. FOR MORE INFORMATION USE THE "DSTAT" COMMAND. (S/R 1205)
- CAUSE
You specified an empty volclass.
- ACTION
Specify a volclass with volume mounted.
- 1206
- MESSAGE
VOLUME "!" SPECIFIED IN THE 'VOL' OPTION IS IN THE PROCESS OF MOUNTING. RESCHEDULE RESTORE WHEN THE MOUNTING IS COMPLETE (S/R 1206)
- CAUSE
Volume is being mount now.
- ACTION
Retype the restore command after volume is mounted.
- 1207
- MESSAGE
RESTORE RECEIVED UNEXPECTED STATUS FROM VOLUME MANAGEMENT. THIS WAS PROBABLY DUE TO HAVING SPECIFIED 'VOL', 'DEV', 'VOLCLASS', OR 'VOLSET OPTIONS WITH CONFLICTING NAMES. VLM ERROR: !. (S/R 1207)
- CAUSE
Various problems and causes.
- ACTION
Check the syntax and try again or call your Hewlett-Packard Support Representative.
- 1251
- MESSAGE
RESTORE ENCOUNTERED MEDIA READ ERROR ON LDEV !. (S/R 1251)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1252
- MESSAGE
RESTORE ENCOUNTERED MEDIA READ ERROR ON REMOTE DEVICE FILE "!". (S/R 1252)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1253
- MESSAGE
RESTORE ENCOUNTERED MEDIA READ ERROR ON FILE "!". (S/R 1253)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1254
- MESSAGE
RESTORE ENCOUNTERED ERROR POSITIONING PAST DIRECTORY ON LDEV !. (S/R 1254)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1255
- MESSAGE
RESTORE ENCOUNTERED ERROR POSITIONING PAST DIRECTORY ON REMOTE DEVICE FILE "!". (S/R 1255)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1256
- MESSAGE
RESTORE ENCOUNTERED ERROR POSITIONING PAST DIRECTORY ON FILE "!". (S/R 1256)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1257
- MESSAGE
RESTORE ENCOUNTERED UNKNOWN MEDIA ON LDEV ! (S/R 1257)
- CAUSE
The media is not recognized by store process.
- ACTION
Mount another media.
- 1258
- MESSAGE
RESTORE ENCOUNTERED UNKNOWN MEDIA ON REMOTE DEVICE FILE "!". (S/R 1258)
- CAUSE
The media is not recognized by store process.
- ACTION
Mount another media.
- 1259
- MESSAGE
RESTORE ENCOUNTERED UNKNOWN MEDIA ON FILE "!". (S/R 1259)
- CAUSE
The media is not recognized by store process.
- ACTION
Mount another media.
- 1260
- MESSAGE
RESTORE ENCOUNTERED ERROR READING STORE LABEL ON LDEV !. (S/R 1260)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1261
- MESSAGE
RESTORE ENCOUNTERED ERROR READING STORE LABEL ON REMOTE DEVICE FILE "!". (S/R 1261)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1262
- MESSAGE
RESTORE ENCOUNTERED ERROR READING STORE LABEL ON FILE "!". (S/R 1262)
- CAUSE
Various problems and causes.
- ACTION
Call your Hewlett-Packard Support Representative.
- 1263
- MESSAGE
ATTEMPTING RESTORE OF MEDIA WITH DAMAGED DIRECTORY ON LDEV !
- CAUSE
Same as the message content.
- ACTION
Information only.
- 1264
- MESSAGE
ATTEMPTING RESTORE OF MEDIA WITH DAMAGED DIRECTORY ON REMOTE DEVICE FILE "!"
- CAUSE
Same as the message content.
- ACTION
Information only.
- 1265
- MESSAGE
ATTEMPTING RESTORE OF MEDIA WITH DAMAGED DIRECTORY ON FILE "!"
- CAUSE
Same as the message content.
- ACTION
Information only.
- 1266
- MESSAGE
ATTEMPTING RESTORE OF MEDIA WITH DAMAGED LABEL ON LDEV !
- CAUSE
Same as the message content.
- ACTION
Information only.
- 1267
- MESSAGE
ATTEMPTING RESTORE OF MEDIA WITH DAMAGED LABEL ON REMOTE DEVICE FILE "!"
- CAUSE
Same as the message content.
- ACTION
Information only.
- 1268
- MESSAGE
ATTEMPTING RESTORE OF MEDIA WITH DAMAGED LABEL ON FILE "!"
- CAUSE
Read error on media label.
- ACTION
Use duplicate store tape.
- 1269
- MESSAGE
RESTORE ENCOUNTERED MEDIA DATA SEQUENCE ERROR ON LDEV !
- CAUSE
Some data blocks on media are missing or corrupted.
- ACTION
Call your support representative.
- 1270
- MESSAGE
RESTORE ENCOUNTERED MEDIA DATA SEQUENCE ERROR ON REMOTE DEVICE FILE "!"
- CAUSE
Some data blocks on media are missing or corrupted.
- ACTION
Call your support representative.
- 1271
- MESSAGE
RESTORE ENCOUNTERED MEDIA DATA SEQUENCE ERROR ON FILE "!"
- CAUSE
Some data blocks on media are missing or corrupted.
- ACTION
Call your support representative.
- 1272
- MESSAGE
RESTORE ENCOUNTERED INCOMPATIBLE MEDIA VERSION ON LDEV !. (S/R 1272)
- CAUSE
Your store subsystem is prior to the tape media version.
- ACTION
Update store subsystem to new media version.
- 1273
- MESSAGE
RESTORE ENCOUNTERED INCOMPATIBLE MEDIA VERSION ON REMOTE DEVICE FILE "!". (S/R 1273)
- CAUSE
Your store subsystem is prior to the tape media version.
- ACTION
Update store subsystem to new media version.
- 1274
- MESSAGE
RESTORE ENCOUNTERED INCOMPATIBLE MEDIA VERSION ON FILE "!". (S/R 1274)
- CAUSE
Your store subsystem is prior to the tape media version.
- ACTION
Update store subsystem to new media version.
- 1275
- MESSAGE
RESTORE RECOVERING MEDIA WITH DAMAGED (UNREADABLE) MEDIA LABEL ON LDEV !
- CAUSE
Media error was encountered while reading the label.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1276
- MESSAGE
RESTORE RECOVERING MEDIA WITH DAMAGED (UNREADABLE) MEDIA LABEL ON REMOTE DEVICE FILE "!"
- CAUSE
Media error was encountered while reading the label.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1277
- MESSAGE
RESTORE RECOVERING MEDIA WITH DAMAGED (UNREADABLE) MEDIA LABEL ON FILE "!"
- CAUSE
Media error was encountered while reading the label.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1278
- MESSAGE
RESTORE ENCOUNTERED ERROR READING MEDIA LABEL ON LDEV !. (S/R 1278)
- CAUSE
Media error was encountered while reading the label.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1279
- MESSAGE
RESTORE ENCOUNTERED ERROR READING MEDIA LABEL ON REMOTE DEVICE FILE "!". (S/R 1279)
- CAUSE
Media error was encountered while reading the label.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1280
- MESSAGE
RESTORE ENCOUNTERED ERROR READING MEDIA LABEL ON FILE "!". (S/R 1280)
- CAUSE
Media error was encountered while reading the label.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1281
- MESSAGE
RESTORE ENCOUNTERED ERROR READING MEDIA DIRECTORY ON LDEV !. (S/R 1281)
- CAUSE
Media error encountered while reading the store set directory.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1282
- MESSAGE
RESTORE ENCOUNTERED ERROR READING MEDIA DIRECTORY ON REMOTE DEVICE FILE "!". (S/R 1282)
- CAUSE
Media error encountered while reading the store set directory.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1283
- MESSAGE
RESTORE ENCOUNTERED ERROR READING MEDIA DIRECTORY ON FILE "!". (S/R 1283)
- CAUSE
Media error encountered while reading the store set directory.
- ACTION
To ensure complete data retrieval use duplicate store tapes.
- 1284
- MESSAGE
RESTORE ENCOUNTERED INCOMPLETE BACKUP ON LDEV ! (S/R 1284)
- CAUSE
RESTORE encountered the end of the media on the specified device before all files were restored.
- ACTION
It is possible that the backup was aborted before it was completely stored. Check to see if there are other reels in the backup.
- 1285
- MESSAGE
RESTORE ENCOUNTERED INCOMPLETE BACKUP ON REMOTE LDEV ! (S/R 1285)
- CAUSE
RESTORE encountered the end of the media on the specified remote device before all files were restored.
- ACTION
It is possible that the backup was aborted before it was completely stored. Check to see if there are other reels in the backup.
- 1286
- MESSAGE
RESTORE ENCOUNTERED INCOMPLETE BACKUP ON FILE "!" (S/R 1286)
- CAUSE
RESTORE encountered the end of the media on the specified disk file before all files were restored.
- ACTION
It is possible that the backup was aborted before it was completely stored. Check to see if there are other reels in the backup.
- 1287
- MESSAGE
RESTORE ENCOUNTERED MISSING TAPE MARK AFTER SSM ON LDEV ! (S/R 1287)
- CAUSE
A RESTORE internal sequencing error occurred on the specified drive.
- ACTION
Contact your HP Support Representative.
- 1288
- MESSAGE
RESTORE ENCOUNTERED MISSING TAPE MARK AFTER SSM ON REMOTE LDEV ! (S/R 1288)
- CAUSE
A RESTORE internal sequencing error occurred on the specified remote drive.
- ACTION
Contact your HP Support Representative.
- 1290
- MESSAGE
RESTORE WAS UNABLE TO SKIP TO THE FINAL MEDIA DIRECTORY ON LDEV ! (S/R 1290)
- CAUSE
RESTORE encountered an error while trying to read in the final media directory for a backup created with ONLINE=END on the specified device.
- ACTION
Make sure the correct media were mounted. If the error persists, contact your HP Support Representative.
- 1291
- MESSAGE
RESTORE WAS UNABLE TO SKIP TO THE FINAL MEDIA DIRECTORY ON REMOVE LDEV ! (S/R 1291)
- CAUSE
RESTORE encountered an error while trying to read in the final media directory for a backup created with ONLINE=END on the specified remote device.
- ACTION
Make sure the correct media were mounted. If the error persists, contact your HP Support Representative.
- 1292
- MESSAGE
RESTORE WAS UNABLE TO SKIP TO THE FINAL MEDIA DIRECTORY ON FILE "!" (S/R 1292)
- CAUSE
RESTORE encountered an error while trying to read in the final media directory for a backup created with ONLINE=END on the specified disk file.
- ACTION
Make sure the correct media were mounted. If the error persists, contact your HP Support Representative.
- 1293
- MESSAGE
RESTORE IS UNABLE TO SKIP TO THE NEXT FILE TO BE RESTORED ON LDEV ! DUE TO A BAD SAVE SET MARK SKIP COUNT (S/R 1293)
- CAUSE
RESTORE needed to skip more than the maximum number of save set marks allowed on one DDS tape.
- ACTION
If ONERR=SKIP was specified, then this is just a warning. RESTORE will prompt you to mount the next tape. However, if ONERR=QUIT was specified, then RESTORE will abort. Retry the restore with ONERR=SKIP.
- 1301
- MESSAGE
LABELED VOLUME FREAD OF STORE LABEL FAILED ON LDEV ! (S/R 1301)
- CAUSE
Internal error occurred trying to read the store label from the first reel.
- ACTION
To ensure complete data retrieval use duplicate store tapes and contact your HP Support Representative further assistance.
- 1304
- MESSAGE
LDEV ! DOES NOT APPEAR TO BE A STORE BACKUP (S/R 1304)
- CAUSE
The disk file specified for the restore does not contain a Store label.
- ACTION
Check you file equations. Make sure they point to a valid store disk backup. Re-run the command.
- 1305
- MESSAGE
REMOTE LDEV ! DOES NOT APPEAR TO BE A STORE BACKUP (S/R 1305)
- CAUSE
The disk file specified for the restore does not contain a Store label.
- ACTION
Check you file equations. Make sure they point to a valid store disk backup. Re-run the command.
- 1306
- MESSAGE
FILE "!" DOES NOT APPEAR TO BE A STORE BACKUP (S/R 1306)
- CAUSE
The disk file specified for the restore does not contain a Store label.
- ACTION
Check you file equations. Make sure they point to a valid store disk backup. Re-run the command.
- 1307
- MESSAGE
RESTORE ENCOUNTERED UNEXPECTED IO ERROR ON LDEV ! (S/R 1307)
- CAUSE
An unexpected error from the I/O system was encountered by RESTORE on the specified device.
- ACTION
Report the error received to your HP Support Representative.
- 1308
- MESSAGE
RESTORE ENCOUNTERED UNEXPECTED IO ERROR ON REMOTE DEVICE FILE "!" (S/R 1308)
- CAUSE
An unexpected error from the I/O system was encountered by RESTORE on the specified remote device.
- ACTION
Report the error received to your HP Support Representative.
Store/Restore (S/R) 1400-1609
- 1401
- MESSAGE
RESTORE ENCOUNTERED IO ERROR: LDEV ! DOES NOT SUPPORT READ TRANSFER LENGTH OF ! BYTES (S/R 1401)
- CAUSE
Media record length can not be handled by current ldev.
- ACTION
Use device which can handle the media record size.
- 1451
- MESSAGE
STORE ENCOUNTERED MEDIA TOO SMALL TO WRITE DIRECTORY ON LDEV ! (S/R 1451)
- CAUSE
The is too short for directory to fit.
- ACTION
Use longer media.
- 1452
- MESSAGE
STORE ENCOUNTERED MEDIA TOO SMALL TO WRITE DIRECTORY ON REMOTE DEVICE FILE "!" (S/R 1452)
- CAUSE
The is too short for directory to fit.
- ACTION
Use longer media.
- 1453
- MESSAGE
STORE ENCOUNTERED MEDIA TOO SMALL TO WRITE DIRECTORY ON FILE "!". (S/R 1453)
- CAUSE
The is too short for directory to fit.
- ACTION
Use longer media.
- 1454
- MESSAGE
STORE ENCOUNTERED MEDIA WRITE ERROR ON LDEV !. (S/R 1454)
- CAUSE
Bad media was encountered on the store device.
- ACTION
Remount a good media.
- 1455
- MESSAGE
STORE ENCOUNTERED MEDIA WRITE ERROR ON REMOTE DEVICE FILE "!". (S/R 1455)
- CAUSE
Bad media was encountered on the store device.
- ACTION
Remount a good media.
- 1456
- MESSAGE
STORE ENCOUNTERED MEDIA WRITE ERROR ON FILE "!". (S/R 1456)
- CAUSE
Bad media was encountered on the store device.
- ACTION
Remount a good media.
- 1457
- MESSAGE
FWRITE TO LABELED VOLUME FAILED ON LDEV ! (S/R 1457)
- CAUSE
Internal error occurred while writing the tape label.
- ACTION
Contact your HP Support representative for further assistance.
- 1460
- MESSAGE
STORE ENCOUNTERED UNEXPECTED IO ERROR ON LDEV ! (S/R 1460)
- CAUSE
An unexpected error from the I/O system was encountered by STORE on the specified device.
- ACTION
Report the error received to your HP Support Representative.
- 1461
- MESSAGE
STORE ENCOUNTERED UNEXPECTED IO ERROR ON REMOTE DEVICE FILE "!" (S/R 1461)
- CAUSE
An unexpected error from the I/O system was encountered by STORE on the specified device.
- ACTION
Report the error received to your HP Support Representative.
- 1551
- MESSAGE
STORE ENCOUNTERED IO ERROR: LDEV ! DOES NOT SUPPORT SPECIFIED DENSITY OF ! BPI. (S/R 1551)
- CAUSE
The default density or one set by a file equation is not valid.
- ACTION
Set correct density by a file equation (option den= ).
- 1552
- MESSAGE
STORE ENCOUNTERED IO ERROR: EXCESSIVE WRITE RETRIES ON LDEV !. PLEASE CLEAN DRIVE HEADS OR MOUNT NEW MEDIA. (S/R 1552)
- CAUSE
Dirty drive write heads or bad media.
- ACTION
Clean drive heads and use new media.
- 1553
- MESSAGE
STORE ENCOUNTERED IO ERROR: LDEV ! DOES NOT SUPPORT SPECIFIED RECORD SIZE OF ! BYTES. (S/R 1553)
- CAUSE
The default record size or one set by a file equation is not valid.
- ACTION
Set correct record size by a file equation (option rec= ).
- 1554
- MESSAGE
SPECIFICALLY, RESTORE RECEIVED ERROR ! FROM SUBSYS ! (S/R 1554)
- CAUSE
RESTORE experienced an unexpected error while doing I/O.
- ACTION
The error and subsystem shown here should be reported to your HP Support representative.
- 1555
- MESSAGE
SPECIFICALLY, RESTORE RECEIVED ERROR ! FROM THE IO SYSTEM (S/R 1555)
- CAUSE
RESTORE experienced an unexpected I/O system error.
- ACTION
The error shown here should be reported to your HP Support representative.
- 1556
- MESSAGE
SPECIFICALLY, STORE RECEIVED ERROR ! FROM SUBSYS ! (S/R 1556)
- CAUSE
STORE experienced an unexpected error while doing I/O.
- ACTION
The error and subsystem shown here should be reported to your HP Support representative.
- 1557
- MESSAGE
SPECIFICALLY, STORE RECEIVED ERROR ! FROM THE IO SYSTEM (S/R 1557)
- CAUSE
STORE experienced an unexpected I/O system error.
- ACTION
The error shown here should be reported to your HP Support representative.
- 1601
- MESSAGE
! NOT STORED: FILE IS NOT IN SPECIFIED VOLUME SET LIST "ONVS"
- CAUSE
The file does not exist on the volume sets specified by ONVS.
- ACTION
Check the file name and the volume set list for errors.
- 1602
- MESSAGE
! WARNING: THIS FILE IS ALREADY LOCKED BY A STORE PROCESS
- CAUSE
Some other user is storing the file or the file name is repeated in the store command.
- ACTION
Check the store command for repeated names or wait until the file is freed by the other user.
- 1603
- MESSAGE
! NOT STORED: FILE IS OPEN FOR WRITING
- CAUSE
File is open for write and hence can not be stored.
- ACTION
Retry when file is not open for write.
- 1604
- MESSAGE
! NOT STORED: LABEL MANAGEMENT ENCOUNTERED ERROR ACCESSING FILE LABEL
- CAUSE
Store could not get the file label.
- ACTION
Call your support representative.
- 1605
- MESSAGE
! NOT STORED: FILE IS NOT IN SPECIFIED FILE CODE RANGE LIST
- CAUSE
The file code is not within the range specified.
- ACTION
Check the file's name, code and the FCRANGE list.
- 1606
- MESSAGE
! NOT STORED: MODIFICATION DATE IS !
- CAUSE
The file did not satisfy the date>= criteria.
- ACTION
Check the file's modify date and date option date.
- 1607
- MESSAGE
! NOT STORED: ACCESS DATE IS !
- CAUSE
The file did not satisfy the data<= criteria.
- ACTION
Check the file's access date and date option date.
- 1608
- MESSAGE
! NOT STORED: READ ACCESS REQUIRES (UV) CAPABILITY
- CAUSE
The user lacks UV capabilty to access the file.
- ACTION
Ask the account/system manager to store the file.
- 1609
- MESSAGE
! NOT STORED: READ ACCESS REQUIRES USER TO BE FILE'S CREATOR
- CAUSE
Only AM/SM have read access to the file besides its creator.
- ACTION
Ask the account/system manager to store the file.
|
Chapter 10 Store/Restore (Native Mode) and TurboSTORE/iX I |
Chapter 12 Store/Restore (Native Mode) and TurboSTORE/iX III |