Clean tape drive and retry. Clean tape drive and remake tape.
Determine cause of incorrect file name on tape and correct.
202
MESSAGE
The procedure failed to initialize the file system directory on
INSTALL.
CAUSE
Error status returned from DRINIT file system initialize
directory.
ACTION
Determine cause of error from DRINIT and correct.
203
MESSAGE
An internal file number error occurred upon trying to get the
disk address of a boot file.
CAUSE
File number error while getting disk address.
(Internal error.)
ACTION
Call your Hewlett-Packard Representative.
204
MESSAGE
An error occurred from file system FFILEINFO getting the disk
address of a boot file.
CAUSE
Error returned from FFILEINFO.
ACTION
Determine cause of error from FFILEINFO and correct.
205
MESSAGE
An error occurred from file system LM_GET_1ST_EXTENT_INFO
getting a disk address of a boot file.
CAUSE
Error returned from LM_GET_1ST_EXTENT_INFO
ACTION
Determine cause of error from LM_GET_1ST_EXTENT_INFO
and correct.
206
MESSAGE
An error occurred from I/O system reading the label for a name
file from tape for RENDEZVOUSIO.
CAUSE
Error returned by RENDEZVOUSIO reading MPEXLDIR file label.
ACTION
Clean tape drive and retry. Clean tape drive, remake tape and retry.
Determine cause of error from RENDEZVOUSIO and correct.
207
MESSAGE
An error occurred from I/O system reading the label for a name
file from the tape from SENDIO.
CAUSE
Error returned by SENDIO reading MPEXLDIR file label.
ACTION
Determine cause of error from SENDIO and correct.
208
MESSAGE
An error occurred reading the label for the name file. Bad tape
or wrong tape position; not enough data read.
CAUSE
Error in length of data reading MPEXLDIR file label.
Tape read expected 256 bytes and got less than 200 bytes.
ACTION
Clean tape drive and retry. Clean tape drive, remake
tape and retry.
209
MESSAGE
An error occurred from I/O system reading the name file from the
tape from RENDEZVOUSIO.
CAUSE
Error returned by RENDEZVOUSIO reading MPEXLDIR file data.
ACTION
Clean tape drive and retry. Clean tape drive, remake tape and retry.
Determine cause of error from RENDEZVOUSIO and correct.
210
MESSAGE
An error occurred from I/O system reading the name file from
the tape from SENDIO.
CAUSE
Error returned by SENDIO reading MPEXLDIR file data.
ACTION
Determine cause of error from SENDIO and correct.
211
MESSAGE
An error occurred reading the name file from the tape; bad
tape or wrong tape position; not enough data read.
CAUSE
Error in length of data reading MPEXLDIR file data. Tape read
expected at least 80 bytes and got less than 80 bytes.
ACTION
Clean tape drive and retry. Clean tape drive, remake
tape and retry.
212
MESSAGE
An error occurred from HPFOPEN to create the name
file.
CAUSE
Error from HPFOPEN for MPEXLDIR file.
ACTION
Determine cause of error from HPFOPEN and correct.
213
MESSAGE
Error from FWRITE on writing name file.
CAUSE
Error from FWRITE for MPEXLDIR file.
ACTION
Determine cause of error from FWRITE and correct.
214
MESSAGE
An error occurred from FCLOSE on the name file.
CAUSE
Error from FCLOSE for MPEXLDIR file.
ACTION
Determine cause of error from FCLOSE and correct.
215
MESSAGE
A failure occurred from INIT_BOOTCMD_AREA.
CAUSE
Error from INIT_BOOTCMD_AREA.
ACTION
Determine cause of error from INIT_BOOTCMD_AREA and correct.
216
MESSAGE
A failure occurred from SAVE_BOOTCMD_TO_DISK.
CAUSE
Error from SAVE_BOOTCMD_TO_DISK.
ACTION
Determine cause of error from SAVE_BOOTCMD_TO_DISK
and correct.
217
MESSAGE
A failure occurred from COMPUTE_FREE_ADDRESS.
CAUSE
Error from COMPUTE_FREE_ADDRESS.
ACTION
Determine cause of error from COMPUTE_FREE_ADDRESS
and correct.
218
MESSAGE
This is an invalid free space map address from
COMPUTE_FREE_ADDRESS; conditional debug compile option.
CAUSE
Incorrect free space bit map address from COMPUTE_FREE_ADDRESS.
Debug code not released.
ACTION
Call your Hewlett-Packard Representative.
219
MESSAGE
A failure occurred from SM_CREATE_HASH_TBL.
CAUSE
Error from SM_CREATE_HASH_TBL. Internal storage management
routine.
ACTION
Determine cause of error from SM_CREATE_HASH_TBL and
correct.
220
MESSAGE
A failure occurred from INSTALL_VOLUME_MGT.
CAUSE
Error from INSTALL_VOLUME_MGT while initializing a volume.
ACTION
Determine cause of error from INSTALL_VOLUME_MGT and
correct.
221
MESSAGE
A failure occurred from local routine LOAD_POST writing to
sector 0,1 of disk.
CAUSE
Error from LOAD_POST writing to sector zero and one
of LDEV 1.
ACTION
Determine cause of error from LOAD_POST and correct.
222
MESSAGE
A failure occurred from local routine LOAD_POST writing to
sector 0,1 of disk.
CAUSE
Error from LOAD_POST writing to sector zero and
one of LDEV 1.
ACTION
Determine cause of error from LOAD_POST and correct.
223
MESSAGE
A failure occurred from file system
FS_INITIALIZE_FILE_SYSTEM.
CAUSE
Error from FS_INITIALIZE_FILE_SYSTEM.
ACTION
Determine cause of error from FS_INITIALIZE_FILE_SYSTEM
and correct.
224
MESSAGE
A failure occurred from file system FS_PROC_INIT.
CAUSE
Error from FS_PROC_INIT, file system initialize routine.
ACTION
Determine cause of error from FS_PROC_INIT and correct.
225
MESSAGE
A failure occurred from file system directory
FAKE_LOGON.
CAUSE
Error from FAKE_LOGON, file system directory routine.
ACTION
Determine cause of error from FAKE_LOGON and correct.
226
MESSAGE
A failure occurred from file system FS_TDIRC_INIT.
CAUSE
Error from FS_TDIRC_INIT, file system routine.
ACTION
Determine cause of error from FS_TDIRC_INIT and correct.
227
MESSAGE
A failure occurred from local routine LOAD_POST writing to
sector 0,1 of disk.
CAUSE
Error from LOAD_POST writing to sector zero and one
of LDEV 1.
ACTION
Determine cause of error from LOAD_POST and correct.
228
MESSAGE
A fatal option error occurred (file name wrong); INSTALL
renamed UPDATE.
CAUSE
A copy of the PME INSTALL has been given control
from the option routine with the indication that the command used
to call the PME was not INSTALL. Probably was UPDATE. Probably a
copy of INSTALL was renamed UPDATE.
ACTION
Use a correct copy of INSTALL.
229
MESSAGE
Disk sparing failed on LDEV 1.
CAUSE
Error returned from disk sparing of LDEV 1.
ACTION
Determine cause of error from sparing and correct.
230
MESSAGE
REBOOT_CPU returned control.
CAUSE
The routine REBOOT_CPU has returned control to the caller.
The CPU was probably not rebooted.
ACTION
Determine why control was returned from REBOOT_CPU and
correct. Reboot the CPU and continue.
231
MESSAGE
Hard loop failed, probably due to compiler or hardware error,
or START/NO START error.
CAUSE
The compiler generated loop to stop the CPU on a
nostart option has exited. Generated code or hardware error.
ACTION
Determine why the code exited and correct. Reboot
the CPU and continue.
232
MESSAGE
An error occurred upon getting the size of the
disk.
CAUSE
Error from GET_HPE_DISC_SIZE_PAGE. Internal routine
to compute the number of pages on the disk.
ACTION
Determine cause of error from GET_HPE_DISC_SIZE_PAGE
and correct.
233
MESSAGE
An error occurred from SM_CREATE_HASH_TBL.
CAUSE
Error from SM_CREATE_HASH_TBL, storage management routine.
ACTION
Determine cause of error from SM_CREATE_HASH_TBL and
correct.
234
MESSAGE
An error occurred from START_VOLUME_MGT.
CAUSE
Error from START_VOLUME_MGT, volume management routine.
ACTION
Determine cause of error from START_VOLUME_MGT and
correct.
235
MESSAGE
An error occurred from file system
FS_INITIALIZE_FILE_SYSTEM.
CAUSE
Error FS_INITIALIZE_FILE_SYSTEM.
ACTION
Determine cause of error from FS_INITIALIZE_FILE_SYSTEM
and correct.
236
MESSAGE
An error occurred from file system FS_PROC_INIT.
CAUSE
Error from FS_PROC_INIT, file system routine.
ACTION
Determine cause of error from FS_PROC_INIT and correct.
237
MESSAGE
An error occurred from file system directory
FAKE_LOGON.
CAUSE
Error from FAKE_LOGON, file system directory logon.
ACTION
Determine cause of error from FAKE_LOGON and correct.
238
MESSAGE
An error occurred from file system FS_TDIRC_INIT.
CAUSE
Error from FS_TDIRC_INIT, file system routine.
ACTION
Determine cause of error from FS_TDIRC_INIT and correct.
239
MESSAGE
This is a fatal option error (filename wrong);
UPDATE renamed INSTALL.
CAUSE
A copy of the PME UPDATE has been given control
from the option routine with the indication that the command used
to call the PME was not UPDATE. Probably was INSTALL. Probably a
copy of UPDATE was renamed INSTALL.
ACTION
Use a correct copy of UPDATE.
240
MESSAGE
Disk sparing failed on LDEV 1.
CAUSE
Error returned from disk sparing of LDEV 1.
ACTION
Determine cause of error from sparing and correct.
241
MESSAGE
REBOOT_CPU returned control.
CAUSE
The routine REBOOT_CPU has returned control to the caller.
The CPU was probably not rebooted.
ACTION
Determine why control was returned from REBOOT_CPU and
correct. Reboot the CPU and continue.
242
MESSAGE
Hard loop failed, probably due to compiler or hardware error,
or START/NO START option error.
CAUSE
The compiler generated loop to stop the CPU on a
nostart option has exited. Generated code or hardware error.
ACTION
Determine why the code exited and correct. Reboot
the CPU and continue.
243
MESSAGE
Failure from SAVE_BOOT_CMD_TO_DISC.
CAUSE
Error from SAVE_BOOT_CMD_TO_DISC.
ACTION
Determine cause of error from SAVE_BOOT_CMD_TO_DISC
and correct.
244
MESSAGE
An error was returned by CONFIGURE_DEVICE configuring the tape
drive.
CAUSE
Error from CONFIGURE_DEVICE for tape control.
ACTION
Determine cause of error from CONFIGURE_DEVICE and
correct.
245
MESSAGE
The procedure found a second IPL on tape; bad tape.
CAUSE
Found second IPL file on the tape. Invalid tape format.
ACTION
Determine cause of the second IPL on the tape and
correct. Remake the tape and redo the UPDATE or INSTALL.
246
MESSAGE
An error was returned by ADD_DUMP_FILE.
CAUSE
Error returned from ADD_DUMP_FILE. Internal routine to
add the dump file to the disk and the LIF directory.
ACTION
Determine cause of error from ADD_DUMP_FILE and correct.
247
MESSAGE
An error was received from LOAD_POST writing label sector 0,1 to
LDEV 1.
CAUSE
Error from LOAD_POST writing to sector zero and
one of LDEV 1.
ACTION
Determine cause of error from LOAD_POST and correct.
248
MESSAGE
No IPL from the tape; disk will not boot.
CAUSE
No IPL file was found on the tape. Invalid tape format.
ACTION
Determine the cause of missing IPL file and correct. Remake
the tape and redo the UPDATE or INSTALL.
249
MESSAGE
No NL.PUB.SYS from the tape; disk will not start.
CAUSE
No NL.PUB.SYS file was found on the tape. Invalid tape format. File
is identified by start number in tape file header.
ACTION
Determine the cause of missing NL.PUB.SYS file and correct.
Remake the tape and redo the UPDATE or INSTALL.
250
MESSAGE
An error was received from CREATE_OBJECT for global
area.
CAUSE
Error returned from CREATE_OBJECT for global area.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
251
MESSAGE
An error was received from CREATE_OBJECT for
page 1 buffer.
CAUSE
Error returned from CREATE_OBJECT for page 1 buffer.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
253
MESSAGE
Bad sector table index error.
CAUSE
An internal error occurred in the disk sparing routine change
sector state. Bad sector table index error.
ACTION
Retry the function (INSTALL or UPDATE or START or mount
volume). Write over sector zero to bypass sparing on this volume
and initialize it again. Consult a Hewlett-Packard System Engineer
for help.
254
MESSAGE
Error on read of TRACK TABLE from RENDEZVOUSIO.
CAUSE
Error returned from RENDEZVOUSIO for sparing read track
table.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
255
MESSAGE
Error on read of TRACK TABLE from SENDIO.
CAUSE
Error returned from SENDIO for sparing read track table.
ACTION
Determine cause of error from SENDIO and correct.
256
MESSAGE
Error on write of TRACK TABLE from RENDEZVOUSIO.
CAUSE
Error returned from RENDEZVOUSIO for sparing write track
table.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
257
MESSAGE
Error on write of TRACK TABLE from SENDIO.
CAUSE
Error returned from SENDIO for sparing write track table.
ACTION
Determine cause of error from SENDIO and correct.
258
MESSAGE
An error was received from SENDIO reading bad sector.
CAUSE
Error returned from SENDIO for sparing read sector
save sector.
ACTION
Determine cause of error from SENDIO and correct.
259
MESSAGE
An error was received from SENDIO writing sector.
CAUSE
Error returned from SENDIO for sparing write sector
save sector.
ACTION
Determine cause of error from SENDIO and correct.
260
MESSAGE
An error was received from SENDIO reading sector from
save area.
CAUSE
Error returned from SENDIO for sparing read sector
for restore sector.
ACTION
Determine cause of error from SENDIO and correct.
261
MESSAGE
An error was received from RENDEZVOUSIO writing sector to
new home.
CAUSE
Error returned from RENDEZVOUSIO for sparing write sector
for restore.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
262
MESSAGE
An error was received from SENDIO writing sector to
new home.
CAUSE
Error returned from SENDIO for sparing write sector
for restore sector.
ACTION
Determine cause of error from SENDIO and correct.
263
MESSAGE
An error was received from SENDIO reading sector from
track.
CAUSE
Error returned from SENDIO for sparing read sector
save track.
ACTION
Determine cause of error from SENDIO and correct.
264
MESSAGE
An error was received from SENDIO writing sector to
save area.
CAUSE
Error returned from SENDIO for sparing write sector
save track.
ACTION
Determine cause of error from SENDIO and correct.
265
MESSAGE
An error was received from SENDIO reading sector from track
save area.
CAUSE
Error returned from SENDIO for sparing read sector
for restore track.
ACTION
Determine cause of error from SENDIO and correct.
266
MESSAGE
An error was received from RENDEZVOUSIO writing sector to
new home.
CAUSE
Error returned from RENDEZVOUSIO for sparing write sector
for restore track.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
267
MESSAGE
An error was received from SENDIO writing sector to
new home.
CAUSE
Error returned from SENDIO for sparing write sector
for restore track.
ACTION
Determine cause of error from SENDIO and correct.
268
MESSAGE
This is a bad SECTOR TABLE index error.
CAUSE
Internal error. Error in sector state in bad sector
table.
ACTION
Retry the function (INSTALL, UPDATE, START or mount volume).
Write over sector zero to bypass sparing on this volume and initialize
it again. Call your Hewlett-Packard Representative.
269
MESSAGE
An error was received from SENDIO running sector
test.
CAUSE
Error returned from SENDIO for sparing run sector test.
ACTION
Determine cause of error from SENDIO and correct.
270
MESSAGE
This is an internal error; error in track start
address.
CAUSE
Internal debug error. Not released. Invalid sector
number from caller for run track test.
ACTION
Call your Hewlett-Packard Representative.
271
MESSAGE
An error was received from SENDIO running track
test.
CAUSE
Error returned from SENDIO for sparing run track test.
ACTION
Determine cause of error from SENDIO and correct.
272
MESSAGE
An error was received from SENDIO running R.O. track
test.
CAUSE
Error returned from SENDIO for sparing run R.O. track test.
ACTION
Determine cause of error from SENDIO and correct.
273
MESSAGE
An error was received from SENDIO running controller
test.
CAUSE
Error returned from SENDIO for sparing run controller test.
ACTION
Call your Hewlett-Packard Representative.
274
MESSAGE
This is an invalid sector address.
CAUSE
Internal debug error. Not released. Invalid sector
number from caller for run track test.
ACTION
Call your Hewlett-Packard Representative.
275
MESSAGE
An error was received from RENDEZVOUSIO sparing a
sector.
CAUSE
Error returned from RENDEZVOUSIO for sparing spare sector.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
276
MESSAGE
An error was received from SENDIO sparing a sector.
CAUSE
Error returned from SENDIO for sparing spare sector.
ACTION
Determine cause of error from SENDIO and correct.
277
MESSAGE
This is an internal error in sector state.
CAUSE
Internal error. Error in sector state in bad sector table.
ACTION
Retry the function (INSTALL, UPDATE, START or mount volume).
Write over sector zero to bypass sparing on this volume and initialize
it again. Call your Hewlett-Packard Representative.
278
MESSAGE
An error was received from SENDIO sparing a track.
CAUSE
Error returned from SENDIO for sparing spare track.
ACTION
Determine cause of error from SENDIO and correct.
282
MESSAGE
A failure occurred from RENDEZVOUSIO skipping forward a tape
file.
CAUSE
Error returned from RENDEZVOUSIO for skip tape file.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
283
MESSAGE
A failure occurred from SENDIO skipping forward a tape
file.
CAUSE
Error returned from SENDIO for skip tape file.
ACTION
Determine cause of error from SENDIO and correct.
284
MESSAGE
A failure occurred from RENDEZVOUSIO rewinding
tape.
CAUSE
Error returned from RENDEZVOUSIO for rewind tape.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
285
MESSAGE
A failure occurred from SENDIO rewinding tape.
CAUSE
Error returned from SENDIO for rewind tape.
ACTION
Determine cause of error from SENDIO and correct.
286
MESSAGE
A failure occurred from RENDEZVOUSIO unloading a
tape.
CAUSE
Error returned from RENDEZVOUSIO for unload tape.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
287
MESSAGE
A failure occurred from SENDIO unloading a tape.
CAUSE
Error returned from SENDIO for unload tape.
ACTION
Determine cause of error from SENDIO and correct.
288
MESSAGE
A failure occurred from RENDEZVOUSIO reading file label
from tape.
CAUSE
Error returned from RENDEZVOUSIO for read tape file label.
Possible tape read error.
ACTION
Determine cause of error from RENDEZVOUSIO and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
289
MESSAGE
A failure occurred from SENDIO reading file label from
tape.
CAUSE
Error returned from SENDIO for read tape file label.
ACTION
Determine cause of error from SENDIO and correct.
290
MESSAGE
Not enough data was read from tape reading the file
label.
CAUSE
Tape read expected 256 bytes and got less than 200
bytes. Possible tape read error or tape position error.
ACTION
Clean tape drive and retry. Clean tape drive, remake
tape and retry.
291
MESSAGE
A failure was received from RENDEZVOUSIO skipping backwards
on tape.
CAUSE
Error returned from RENDEZVOUSIO for skip record back.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
292
MESSAGE
A failure was received from SENDIO skipping backwards on
tape.
CAUSE
Error returned from SENDIO for skip record back.
ACTION
Determine cause of error from SENDIO and correct.
293
MESSAGE
A second NL.PUB.SYS was found on the boot tape.
CAUSE
A second NL.PUB.SYS file was found on the tape. Invalid tape format.
File is identified by start number in tape file header.
ACTION
Determine the cause of the extra NL.PUB.SYS file and correct.
Remake the tape and redo the UPDATE or INSTALL.
294
MESSAGE
Can not purge NL.PUB.SYS from disk.
CAUSE
Error returned from HPOPEN for create of NL.PUB.SYS. File
is identified by start number in tape file header.
ACTION
Determine cause of error from HPOPEN and correct.
296
MESSAGE
A failure occurred from RENDEZVOUSIO reading user label
block.
CAUSE
Error returned from RENDEZVOUSIO for read user label block
of a system file.
ACTION
Determine cause of error from RENDEZVOUSIO and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
297
MESSAGE
Length error reading user label block.
CAUSE
EOF read from tape while reading user label data. Invalid tape.
Possible tape read error or tape position error.
ACTION
Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
298
MESSAGE
A failure occurred from SENDIO reading user label
block.
CAUSE
Error returned from SENDIO for read user label block.
ACTION
Determine cause of error from SENDIO and correct.
299
MESSAGE
An error occurred from FWRITELABEL writing user
label.
CAUSE
Condition code error returned by FWRITE for user
label block.
ACTION
Determine cause of error from FWRITE and correct.
Messages 300 - 350
300
MESSAGE
A failure occurred from RENDEZVOUSIO reading system file block
from tape.
CAUSE
Error returned from RENDEZVOUSIO for read file block. Possible
tape read error or tape position error.
ACTION
Determine cause of error from RENDEZVOUSIO and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
301
MESSAGE
This is a premature EOF on tape reading the system file
block.
CAUSE
An EOF was read from the tape before expected while reading
system file data. Invalid tape. Possible tape read error or tape
position error.
ACTION
Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
302
MESSAGE
A failure was received from SENDIO reading system file
block.
CAUSE
Error returned from SENDIO for system file block.
ACTION
Determine cause of error from SENDIO and correct.
303
MESSAGE
An error occurred from FWRITE on system file block.
CAUSE
Condition code error returned by FWRITE for file
data block.
ACTION
Determine cause of error from FWRITE and correct.
304
MESSAGE
An error occurred from FCLOSE on system file.
CAUSE
Error from FCLOSE for system file.
ACTION
Determine cause of error from FCLOSE and correct.
305
MESSAGE
There is an error in the number of blocks on tape for system
file; file length error.
CAUSE
Record count error from tape while reading system file data. Invalid
tape. Possible tape read error or tape position error.
ACTION
Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
306
MESSAGE
HPOPEN error occurred for DUMPAREA.
CAUSE
Error returned from HPOPEN for create of DUMPAREA.MPEXL.SYS.
ACTION
Determine cause of error from HPOPEN and correct.
307
MESSAGE
An error was received from FWRITE for DUMPAREA.
CAUSE
Condition code error returned by FWRITE for
DUMPAREA.MPEXL.SYS.
ACTION
Determine cause of error from FCLOSE and correct.
308
MESSAGE
Error from FCLOSE for DUMPAREA.
CAUSE
Error from FCLOSE for DUMPAREA.MPEXL.SYS file.
ACTION
Determine cause of error from FCLOSE and correct.
310
MESSAGE
An error was received from HPOPEN for creating boot
file.
CAUSE
Error returned from HPOPEN for create of a boot file.
ACTION
Determine cause of error from HPOPEN and correct.
311
MESSAGE
An error occurred on reading the tape boot file
block.
CAUSE
Error returned from SENDIO for read file block from tape.
ACTION
Determine cause of error from SENDIO and correct.
312
MESSAGE
There was an error in the number of blocks on the tape for the
boot file; file length error.
CAUSE
User label numbers in tape file label are incorrect. Invalid tape
format. User labels are invalid for a boot file.
ACTION
Determine cause of incorrect numbers and correct. Remake
tape and retry the UPDATE or INSTALL.
313
MESSAGE
An error was received from FWRITE on the boot file.
CAUSE
EOF read from tape before expected while reading boot file data.
Invalid tape. Possible tape read error or tape position error.
ACTION
Determine cause of error and correct. Clean tape drive and retry.
Clean tape drive, remake tape and retry.
314
MESSAGE
Failure posting page 1 to disk.
CAUSE
Error from LOAD_POST writing to sector zero and
one of LDEV 1.
ACTION
Determine cause of error from LOAD_POST and correct.
315
MESSAGE
An error was received from FCLOSE of boot file.
CAUSE
Error from FCLOSE for a boot file.
ACTION
Determine cause of error from FCLOSE and correct.
316
MESSAGE
The procedure failed to add boot file to the LIF
directory.
CAUSE
Error returned from ADD_NEXT_DIR_ENTRY for a boot file
while attempting to add an entry to the LIF directory.
ACTION
Determine cause of error from ADD_NEXT_DIR_ENTRY and
correct.
317
MESSAGE
There was an error in the number of blocks on tape for the boot
file; file length error.
CAUSE
Record count error from tape while reading boot file data. Invalid
tape. Possible tape read error or tape position error.
ACTION
Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
318
MESSAGE
An error was received from RENDEZVOUSIO reading first label
from tape.
CAUSE
Error returned from RENDEZVOUSIO for read labels. First read from
the tape. Possible tape read error or tape position error.
ACTION
Determine cause of error from RENDEZVOUSIO and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
319
MESSAGE
An error was received from SENDIO reading the first label from
the tape.
CAUSE
Error returned from SENDIO for read labels. First
read from the tape.
ACTION
Determine cause of error from SENDIO and correct.
320
MESSAGE
An error occurred on the first read; not enough data
read.
CAUSE
Tape read expected 256 bytes and got less than 200 bytes. Possible
tape read error or tape position error. First read from
the tape. Reading labels.
ACTION
Clean tape drive and retry. Clean tape drive, remake
tape and retry.
321
MESSAGE
An error was received from RENDEZVOUSIO reading the second
label from the tape.
CAUSE
Error returned from RENDEZVOUSIO for read labels. Second read from
the tape. Possible tape read error or tape position error.
ACTION
Determine cause of error from RENDEZVOUSIO and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
322
MESSAGE
An error was received from SENDIO reading the second label from
the tape.
CAUSE
Error returned from SENDIO for read labels. Second
read from the tape.
ACTION
Determine cause of error from SENDIO and correct.
323
MESSAGE
An error occurred on the second read; not enough data
read.
CAUSE
Tape read expected 256 bytes and got less than 200 bytes. Possible
tape read error or tape position error. Second read from
the tape. Reading labels.
ACTION
Clean tape drive and retry. Clean tape drive, remake
tape and retry.
324
MESSAGE
An error was received from RENDEZVOUSIO reading the LIF
directory from the tape.
CAUSE
Error returned from RENDEZVOUSIO for read labels. Third read from
the tape. Possible tape read error or tape position error.
ACTION
Determine cause of error from RENDEZVOUSIO and correct. Clean tape
drive and retry. Clean tape drive, remake tape and retry.
325
MESSAGE
An error was received from SENDIO reading the LIF directory
from the tape.
CAUSE
Error returned from SENDIO for read labels. Third
read from the tape.
ACTION
Determine cause of error from SENDIO and correct.
326
MESSAGE
An error occurred reading the LIF directory from the tape;
not enough data.
CAUSE
Tape read expected 256 bytes and got less than 200 bytes. Possible
tape read error or tape position error. Third read from
the tape. Reading labels.
ACTION
Clean tape drive and retry. Clean tape drive, remake
tape and retry.
327
MESSAGE
This is not an MPE/iX boot tape; LIF label bad.
CAUSE
LIF label check failed. Not a valid boot tape.
ACTION
Retry with a valid boot tape.
328
MESSAGE
This is not an MPE/iX boot tape; MPE/iX label bad.
CAUSE
MPE/iX label check failed. Not a valid boot tape.
ACTION
Retry with a valid boot tape.
330
MESSAGE
An error was received from SENDIO writing disk
page 1.
CAUSE
Error from LOAD_POST writing to sector zero and one of LDEV 1.
First write to sector zero and one of LDEV 1.
ACTION
Determine cause of error from LOAD_POST and correct.
331
MESSAGE
An error was received from CREATE_OBJECT for first tape I/O
buffer.
CAUSE
Error returned from CREATE_OBJECT for tape I/O buffer 1.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
332
MESSAGE
An error was received from CREATE_OBJECT for a second tape
I/O buffer.
CAUSE
Error returned from CREATE_OBJECT for tape I/O buffer 2.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
333
MESSAGE
An error was received from CREATE_OBJECT for the tape LIF
directory buffer.
CAUSE
Error returned from CREATE_OBJECT for tape LIF directory
buffer.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
334
MESSAGE
An error was received from CREATE_OBJECT for the disk LIF
directory buffer.
CAUSE
Error returned from CREATE_OBJECT for disk LIF directory
buffer.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
335
MESSAGE
An error was received from CREATE_OBJECT for the tape LIF
label buffer.
CAUSE
Error returned from CREATE_OBJECT for tape LIF label buffer.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
336
MESSAGE
An error was received from CREATE_OBJECT for the tape
MPE/iX label.
CAUSE
Error returned from CREATE_OBJECT for tape MPE/iX label
buffer.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
337
MESSAGE
An error was received from HPOPEN for creating LIF
directory.
CAUSE
Error from HPOPEN for LIFDIREC file.
ACTION
Determine cause of error from HPOPEN and correct.
338
MESSAGE
An error was received from FWRITE for the LIF
directory.
CAUSE
Error from FWRITE for LIFDIREC file.
ACTION
Determine cause of error from FWRITE and correct.
339
MESSAGE
An error was received from FCLOSE, closing the LIF
directory.
CAUSE
Error from FCLOSE for LIFDIREC file.
ACTION
Determine cause of error from FCLOSE and correct.
340
MESSAGE
An error occurred writing page 1 of the disk.
CAUSE
Error from LOAD_POST writing sector zero and one of LDEV 1.
ACTION
Determine cause of error from LOAD_POST and correct.
341
MESSAGE
An error was received from RENDEZVOUSIO reading the disk
labels.
CAUSE
Error returned from RENDEZVOUSIO for read disk page 1,
sector zero and one.
ACTION
Determine cause of error from RENDEZVOUSIO and correct.
342
MESSAGE
An error was received from SENDIO reading the disk
labels.
CAUSE
Error returned from SENDIO for read disk page 1,
sector zero and one.
ACTION
Determine cause of error from SENDIO and correct.
343
MESSAGE
This is not an MPE XL disk. UPDATE failed; INSTALL
required.
CAUSE
Disk LDEV 1 is not a valid MPE/iX system master volume.
ACTION
Replace with a valid MPE/iX system master and retry. Volume
cannot be updated, INSTALL is required.
345
MESSAGE
System Abort 345
CAUSE
Internal error. Invalid spare state. Debug code
not released.
ACTION
Call your Hewlett-Packard Representative.
346
MESSAGE
A failure was received from CREATE_OBJECT for a semaphore to
use to interlock the label.
CAUSE
Error returned from CREATE_OBJECT for volume label
semaphore.
ACTION
Determine cause of error from CREATE_OBJECT and correct.
347
MESSAGE
A failure was received from
CREATE_BAD_SECTOR_TABLE.
CAUSE
Error returned from CREATE_BAD_SECTOR_TABLE.
ACTION
Determine cause of error from CREATE_BAD_SECTOR_TABLE
and correct.
348
MESSAGE
A failure was received from XM_INITXM.
CAUSE
Error from STARTGOLDENXID, transaction management routine.
ACTION
Determine cause of error from STARTGOLDENXID and correct.
349
MESSAGE
A failure was received from XM_INITXM.
CAUSE
Error from ENDGOLDENXID, transaction management routine.
ACTION
Determine cause of error from ENDGOLDENXID and correct.