Sysmain
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II | |
| E0300 Volume I | |
| E0300 Volume II | |
| E0300 Volume III ♥ | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
- 1
- MESSAGE
CAN'T ABORT I/O ON A VIRTUAL LOGICAL DEVICE. (sys 1)
- 2
- MESSAGE
CAN'T ABORT I/O ON A DISC LOGICAL DEVICE. (sys 2)
- 3
- MESSAGE
NOT A VALID LOGICAL DEVICE. (sys 3)
- 4
- MESSAGE
CAN'T ABORT I/O ON A SPOOLER LOGICAL DEVICE. (sys 4)
- 5
- MESSAGE
LOGICAL DEVICE IS NOT CONFIGURED. (sys 5)
- 6
- MESSAGE
CAN'T ABORT THIS JOB/SESSION. (sys 6)
- 7
- MESSAGE
INVALID JOB IDENTIFIER. (sys 7)
- 8
- MESSAGE
ALREADY IN SINGLE USER MODE. (sys 8)
- 9
- MESSAGE
CAN'T FORCE LOGOFF. (sys 9)
- 10
- MESSAGE
CURRENTLY IN LOGOFF MODE. (sys 10)
- 11
- MESSAGE
MISSING JOB/SESSION # SPECIFIER. (sys 11)
- 12
- MESSAGE
ALREADY IN MULTI-USER MODE. (sys 12)
- 13
- MESSAGE
LOGON NOT PERMITTED BY DIAGNOSTICS. (sys 13)
- 14
- MESSAGE
CAN'T FORCE LOGON. (sys 14)
- 15
- MESSAGE
NO REQUESTS PENDING. (sys 15)
- 16
- MESSAGE
INVALID RID TYPE. (sys 16)
- 17
- MESSAGE
MISSING PARAMETER. (sys 17)
- 18
- MESSAGE
MISSING PARAMETER LENGTH. (sys 18)
- 19
- MESSAGE
INVALID REPLY IDENTIFIER. (sys 19)
- 20
- MESSAGE
REPLY IS TOO LONG. (sys 20)
- 21
- MESSAGE
PARAMETER IS TOO LONG. (sys 21)
- 22
- MESSAGE
COMMAND NAME IS TOO LONG. (sys 22)
- 23
- MESSAGE
INVALID COMMAND NAME. (sys 23)
- 24
- MESSAGE
CAN'T CREATE THE SYSTEM PORT. (sys 24)
- 25
- MESSAGE
CAN'T CREATE THE REPLY INFORMATION TABLE. (sys 25)
- 26
- MESSAGE
CAN'T GET A COMMAND. (sys 26)
- 27
- MESSAGE
CAN'T RESTORE ORIGINAL STATE OF CONSOLE. (sys 27)
- 28
- MESSAGE
CAN'T CREATE A STATUS REPLY PORT. (sys 28)
- 29
- MESSAGE
CAN'T RECEIVE STATUS. (sys 29)
- 30
- MESSAGE
CAN'T PURGE STATUS REPLY PORT. (sys 30)
- 31
- MESSAGE
MUST HAVE DI CAPABILITY. (sys 31)
- 32
- MESSAGE
CAN'T ENABLE/DISABLE CONSOLE MODE. (sys 32)
- 33
- MESSAGE
CAN'T SHUT DOWN. (sys 33)
- 34
- MESSAGE
CURRENTLY SHUTTING DOWN. (sys 34)
- 35
- MESSAGE
NO I/O TO ABORT FOR DEVICE !. (sys 35)
- 36
- MESSAGE
HLIO INTERNAL ERROR. COMMAND CANNOT BE EXECUTED. (sys 36)
- 37
- MESSAGE
THIS JOB/SESSION DOES NOT EXIST. (sys 37)
- 38
- MESSAGE
TOO MANY PARAMETERS WERE GIVEN. (sys 38)
- 39
- MESSAGE
EXPECTED USER NAME IN USERNAME.ACCTNAME PARAMETER. (sys 39)
- 40
- MESSAGE
MISSING USER NAME IN USERNAME.ACCTNAME. (sys 40)
- 41
- MESSAGE
PARAMETER EXCEEDS THE LENGTH OF USER/JOB/ACCT NAMES. (sys 41)
- 42
- MESSAGE
EXPECTED [JOBNAME,]USERNAME.ACCTNAME. (sys 42)
- 43
- MESSAGE
MISSING ACCT NAME IN USERNAME.ACCTNAME PARAMETER. (sys 43)
- 44
- MESSAGE
INVALID CHARACTER WAS FOUND. (sys 44)
- 47
- MESSAGE
SYSTEM CURRENTLY IN AN UNKNOWN MODE. (sys 47)
- 100
- MESSAGE
UNRECOGNIZED SUBSYSTEM #!, INFO = !. (sys 100)
- 200
- MESSAGE
System State: Initializing Mode. (sys 200)
- 201
- MESSAGE
System State: Multiuser Mode. (sys 201)
- 202
- MESSAGE
System State: Single User Mode. (sys 202)
- 203
- MESSAGE
System State: Single User - No Logon Mode. (sys 203)
- 204
- MESSAGE
System State: No User Mode. (sys 204)
- 205
- MESSAGE
System State: Terminating Mode. (sys 205)
- 210
- MESSAGE
Reply Information Table has been initialized! (sys 210)
|
Symbolic Debugger |
System Disk Load (Subsystem 148) |