High Level I/O (Subsystem 111)
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II | |
| E0300 Volume I | |
| E0300 Volume II | |
| E0300 Volume III ♥ | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
- 1
- MESSAGE
The I/O request was aborted.
- CAUSE
Many possible causes.
- ACTION
This is a warning message and not a standard error condition. Therefore, no additional action is required.
- 2
- MESSAGE
The I/O request is currently active.
- CAUSE
Same as message content.
- ACTION
This is a warning message and not a standard error condition. Therefore, no additional action is required.
- 3
- MESSAGE
The request is currently queued in the manager's input queue.
- CAUSE
Same as message content.
- ACTION
This is a warning message and not a standard error condition. Therefore, no additional action is required.
- 4
- MESSAGE
The LDEV specified was invalid.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 5
- MESSAGE
The LDEV specified was not configured.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 6
- MESSAGE
A bad virtual address or nil pointer was specified.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 7
- MESSAGE
The length specified was negative, or the total length in the user data chain did not add up to length.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 8
- MESSAGE
The sector specified was zero.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 9
- MESSAGE
The function specified was invalid for this device.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 10
- MESSAGE
The message was not found in the input queue.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 11
- MESSAGE
The subqueue specified is used by the I/O system.
- CAUSE
Same as for message Content.
- ACTION
Call your Hewlett-Packard Representative.
- 13
- MESSAGE
The I/O completion port must be ICS-sendable.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 14
- MESSAGE
The I/O completion port must be able to handle the largest HLIO message.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 15
- MESSAGE
The I/O completion port must have 32 subqueues.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 17
- MESSAGE
The procedure can not be called from the ICS.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 18
- MESSAGE
The device is in a disabled state, and I/O may not be performed to it.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 19
- MESSAGE
The data chain passed to SENDIO had unaligned data.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 20
- MESSAGE
The I/O request has generated more than the maximum of 32 data chains.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 21
- MESSAGE
The I/O request index supplied was outside the range of the table.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 22
- MESSAGE
The RENDEZVOUS for the I/O request has already been done.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 24
- MESSAGE
A message was received by the LDM that was not understood.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 25
- MESSAGE
A request to release the device was issued while the device was still allocated.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 26
- MESSAGE
A die request was sent to the LDM, but the LDM is still bound to DM.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 27
- MESSAGE
A request to release the device was issued while I/O was still active.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 28
- MESSAGE
The LDM is bound to a different DM than specified in the LDM_DO_UNBIND_MSG.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 29
- MESSAGE
The request failed because we were out of resources.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 30
- MESSAGE
The function requested is not implemented.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 31
- MESSAGE
There are currently no outstanding requests for the device.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 32
- MESSAGE
The device class is invalid.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 33
- MESSAGE
The COMPATIBILITY MODE I/O queue index is invalid.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 34
- MESSAGE
There is a flow control problem in the LDM.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 35
- MESSAGE
There is a flow control problem in the LDM.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 36
- MESSAGE
The procedure failed to make the user's buffer present.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 37
- MESSAGE
The request to abort a MIB chain has found an already aborted MIB.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
- 38
- MESSAGE
An HLIO internal error was detected.
- CAUSE
Internal error.
- ACTION
Call your Hewlett-Packard Representative.
|
Floating Point Conversion (Subsystem 193) |
HPIB Adapter Manager (Subsystem 116) |