Chapter 10 Store/Restore (Native Mode) and TurboSTORE/iX I
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II | |
| E0300 Volume I | |
| E0300 Volume II ♥ | |
| E0300 Volume III | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
Store/Restore Messages 1 - 199
- 1
- MESSAGE
(RE)STORE ENCOUNTERED EXCESSIVE REWIND ERRORS ON LDEV !
- CAUSE
Bad media or drive problem caused too many errors.
- ACTION
Physically dismount bad media and mount new one.
- 6
- MESSAGE
READY TO TRY REWIND FOR (RE)STORE on LDEV ! (Y/N)
- CAUSE
Too many rewind errors on previous try.
- ACTION
Mount good media and reply to console query.
- 11
- MESSAGE
STORE/RESTORE ENCOUNTERED UNKNOWN MEDIA ON LDEV !
- CAUSE
Media type is incompatible with store subsystem.
- ACTION
Mount compatible media type or update store.
- 16
- MESSAGE
LABEL READ FAIL ON LDEV !. USE ANYWAY?(Y/N)
- CAUSE
Media read error while trying to read media label.
- ACTION
Check paper label on media and reply to the console query.
- 17
- MESSAGE
LABEL READ FAIL ON LDEV ! FOR MEDIA !. USE IT?(Y/N)
- CAUSE
Media read error on label read with (re)storeset option.
- ACTION
Check paper label on media and reply to console query.
- 18
- MESSAGE
LABEL READ FAIL ON LDEV ! FOR MEDIA !. USE IT?(Y/N)
- CAUSE
Media read error on label read with (re)storeset option.
- ACTION
Check the paper label and reply to the console query.
- 21
- MESSAGE
MOUNT NEXT MEDIA FOR RESTORE ON LDEV !
- CAUSE
Restore finished the current mounted media.
- ACTION
Mount next media to be restored.
- 22
- MESSAGE
MOUNT MEDIA ! FOR RESTORE ON LDEV !
- CAUSE
Restore with restoreset option finished the currently mounted media.
- ACTION
Mount next media on specified ldev.
- 23
- MESSAGE
MOUNT MEDIA ! OF SET ! FOR RESTORE ON LDEV !
- CAUSE
Restore with restoreset finished a media from parallal set store.
- ACTION
Mount next media of the specified set on requesting ldev.
- 26
- MESSAGE
DISMOUNT CURRENT MEDIA FOR RESTORE ON LDEV !
- CAUSE
A wrong media was mounted for restore on specified ldev.
- ACTION
Dismount wrong media and mount a correct one.
- 27
- MESSAGE
DISMOUNT MEDIA ! FOR RESTORE ON LDEV !
- CAUSE
An out of order media was mounted.
- ACTION
Dismount this media and mount a correct one.
- 28
- MESSAGE
DISMOUNT MEDIA ! OF SET ! FOR RESTORE ON LDEV !
- CAUSE
An out of order media was mounted for restore.
- ACTION
Dismount wrong media and mount the correct one.
- 30
- MESSAGE
MEDIA LEADER TOO SHORT. DISMOUNT CURRENT MEDIA ON LDEV !
- CAUSE
Media error encountered due to insufficient media leader.
- ACTION
Mount media with long enough media leader.
- 31
- MESSAGE
MEDIA ON LDEV ! IS NOT A STORE MEDIA
- CAUSE
A non-store media is mounted for restore.
- ACTION
Only store media can be read by NM restore.
- 36
- MESSAGE
MEDIA ON LDEV ! IS PREVIOUS TO REQUESTED MEDIA
- CAUSE
An out of order media was mounted for restore.
- ACTION
Dismount this media and mount the correct one.
- 37
- MESSAGE
MEDIA ! ON LDEV ! IS PREVIOUS TO REQUESTED MEDIA
- CAUSE
An out of order media was mounted for restore with restoreset option.
- ACTION
Dismount this media and mount the correct one.
- 38
- MESSAGE
MEDIA ! OF SET ! ON LDEV ! IS PREVIOUS TO REQUESTED MEDIA
- CAUSE
An out of order media from a parallel storeset was mounted for restore.
- ACTION
Dismount this media and mount the correct one.
- 41
- MESSAGE
INCORRECT MEDIA DISMOUNTED BY RESTORE ON LDEV !
- CAUSE
An incorrect media was placed offline by restore.
- ACTION
Unload this media and mount the correct one.
- 46
- MESSAGE
MEDIA ON LDEV ! IS NOT FROM THIS STORE SET
- CAUSE
The mounted media is not from the set being restored on this ldev.
- ACTION
Dismount the incorrect media and mount the correct one.
- 47
- MESSAGE
MEDIA ON LDEV ! WAS MOUNTED BUT NEVER WRITTEN
- CAUSE
Although the media on the specified ldev was mounted (most likely for a serial store), no data was written to it.
- ACTION
Do not include this media as part of the backup, since it contains no data.
- 51
- MESSAGE
MEDIA ON LDEV ! WAS NOT REQUESTED. USE IT? (Y/N)
- CAUSE
Media later than requested was mounted on ldev.
- ACTION
Reply Y if you want to skip media otherwise reply n and mount correct media.
- 52
- MESSAGE
MEDIA ! ON LDEV ! WAS NOT REQUESTED. USE IT? (Y/N)
- CAUSE
Media later than requested was mounted along with restoreset option.
- ACTION
Reply Y if want to skip media or else reply N and mount the correct media.
- 53
- MESSAGE
MEDIA ! OF SET ! ON LDEV ! IS WRONG. USE IT? (Y/N)
- CAUSE
Media from later set than requested was mounted.
- ACTION
Reply Y if want to skip media else reply y and mount correct media.
- 56
- MESSAGE
MOUNT NEXT MEDIA FOR STORE ON LDEV !
- CAUSE
Store finished writing the current media .
- ACTION
Unload current media and mount a new one.
- 57
- MESSAGE
MOUNT MEDIA ! FOR STORE ON LDEV !
- CAUSE
Store with storeset option finished writing a media.
- ACTION
Unload the current media and mount a new one.
- 58
- MESSAGE
MOUNT MEDIA ! OF SET ! FOR STORE ON LDEV !
- CAUSE
Store with storeset option finished writing a media.
- ACTION
Unload the current media and mount a new one.
- 61
- MESSAGE
STORE IS STARTING TO WRITE NEXT MEDIA ON LDEV !
- CAUSE
Store accepted the newly mounted media.
- ACTION
None.
- 62
- MESSAGE
STORE IS STARTING TO WRITE MEDIA ! ON LDEV !
- CAUSE
Store with storeset option accepted the newly mounted media.
- ACTION
None.
- 63
- MESSAGE
STORE IS STARTING TO WRITE MEDIA ! OF SET ! ON LDEV !
- CAUSE
Store with storeset option accepted the newly mounted media.
- ACTION
None.
- 66
- MESSAGE
MEDIA ON LDEV ! IS PART OF CURRENT STORE SET
- CAUSE
Media of the current store command was remounted to be overwritten.
- ACTION
Save this media and mount a blank one instead.
- 67
- MESSAGE
MEDIA ! ON LDEV ! IS PART OF CURRENT STORE SET
- CAUSE
Media from current store with storeset option was mounted to be overwritten.
- ACTION
Save this media and mount a blank one.
- 68
- MESSAGE
MEDIA ! OF SET ! ON LDEV ! IS PART OF CURRENT STORE SET
- CAUSE
Media of current store with storeset option was mounted to be overwritten.
- ACTION
Save this media and mount a blank one.
- 71
- MESSAGE
MEDIA ON LDEV ! IS BAD. CONTINUE ANYWAY?(Y/N)
- CAUSE
The media just mounted gave write errors at some time before this.
- ACTION
Reply Y if you want to retry the media or else reply N and mount a good media.
- 76
- MESSAGE
STORE IS MARKING MEDIA BAD ON LDEV !
- CAUSE
Store came accross a write error on this media.
- ACTION
Dismount this media and mount a good one.
- 77
- MESSAGE
STORE IS MARKING MEDIA ! BAD ON LDEV !
- CAUSE
Store with storeset option had a write error on specified ldev.
- ACTION
Dismount bad media and mount a good one.
- 78
- MESSAGE
STORE IS MARKING MEDIA ! OF SET ! BAD ON LDEV !
- CAUSE
Store with storeset option had a write error on the specified ldev.
- ACTION
Dismount bad media and mount a good one.
- 81
- MESSAGE
RESTORE IS ASSUMING THAT NEXT MEDIA IS ON LDEV !
- CAUSE
Media was mounted on ldev out of sequence with restoreset order.
- ACTION
None.
- 82
- MESSAGE
RESTORE IS ASSUMING THAT MEDIA ! IS ON LDEV !
- CAUSE
Media was mounted on an ldev out of sequence from restoreset order.
- ACTION
None.
- 83
- MESSAGE
RESTORE IS ASSUMING THAT MEDIA ! OF SET ! IS ON LDEV !
- CAUSE
Media was mounted on ldev out of sequence with the restoreset option order.
- ACTION
None.
- 86
- MESSAGE
USE DAMAGED TAPE AS NEXT MEDIA ON LDEV !(Y/N)
- CAUSE
The media directory on this media was damaged.
- ACTION
Reply Y if this indeed is the correct media or else reply N and mount the correct one.
- 87
- MESSAGE
USE DAMAGED TAPE AS MEDIA ! ON LDEV !(Y/N)
- CAUSE
The media directory on this media was found to be damaged.
- ACTION
Reply Y to console query if this indeed is the correct media or else reply N.
- 88
- MESSAGE
USE DAMAGED TAPE AS MEDIA ! OF SET ! ON LDEV !(Y/N)
- CAUSE
The media directory on this media was damaged.
- ACTION
Reply Y to the console query if this indeed is the correct media or else reply N.
- 91
- MESSAGE
FILES LOCKED BY ONLINE STORE ARE NOW FREE FOR READ/WRITE/PURGE
- CAUSE
The files specified for an online store have been attached to the logging mechanism.
- ACTION
These files may now been opened for read or write access, or may be purged.
- 92
- MESSAGE
THE MEDIA ON LDEV ! IS ALLOCATED TO SOME OTHER DRIVE
- CAUSE
The media that has been mounted belongs to a parallel restoreset that is already being restored on another device.
- ACTION
Dismount this media and mount a piece of media that does not belong to an already allocated restoreset.
- 93
- MESSAGE
MEDIA ! ON LDEV ! IS ALLOCATED TO SOME OTHER DRIVE
- CAUSE
The media that has been mounted belongs to a parallel restoreset that is already being restored on another device.
- ACTION
Dismount this tape and mount a piece of media that does not belong to an already allocated restoreset.
- 94
- MESSAGE
MEDIA ! OF SET ! ON LDEV ! IS ALLOCATED TO SOME OTHER DRIVE
- CAUSE
The media that has been mounted belongs to a parallel restoreset that is already being restored on another device.
- ACTION
Dismount this tape and mount a piece of media that does not belong to an already allocated restoreset.
- 96
- MESSAGE
FILES OF STORE SET ! WILL BE RESTORED WHEN A DRIVE BECOMES FREE
- CAUSE
There are more parallel restoresets to restore than there are devices, so the specified set will be restored once a backup device becomes available.
- ACTION
Information only. When a drive becomes free, this set can be mounted and restored.
- 99
- MESSAGE
STARTING TO RESTORE THE FILES OF STORE SET ! ON LDEV !
- CAUSE
The files of the specified store set are now being restored from the specified ldev.
- ACTION
Information only.
- 102
- MESSAGE
LDEV ! SPECIFIED IN THE RESTORESET OPTION IS RELEASED
- CAUSE
There are no files to restore from this device, so it is being closed.
- ACTION
Information only.
- 114
- MESSAGE
LABELED VOLUME MOUNTED FOR UNLABELED STORE ON LDEV !.
- CAUSE
Labeled volumes can not be used for unlabeled stores.
- ACTION
Dismount this volume and mount an unlabeled media.
- 115
- MESSAGE
DISMOUNT VOLUME OF VOLSET ! FOR RESTORE ON LDEV !
- CAUSE
The specified labeled volume is no longer needed by restore.
- ACTION
Dismount the volume from the specified ldev.
- 116
- MESSAGE
DISMOUNT MEDIA ! OF VOLSET ! FOR RESTORE ON LDEV !
- CAUSE
The specifieid lableled volume is no longer needed by restore.
- ACTION
Dismount the volume from the specified ldev.
- 117
- MESSAGE
DISMOUNT VOL ! OF VOLSET ! FOR RESTORE ON LDEV !
- CAUSE
The specifieid lableled volume is no longer needed by restore.
- ACTION
Dismount the volume from the specified ldev.
- 118
- MESSAGE
FILES OF VOLSET ! WILL BE RESTORED WHEN A DRIVE BECOMES FREE
- CAUSE
There are more parallel restoresets to restore than there are devices, so the specified volume set will be restored once a backup device becomes available.
- ACTION
Information only. When a drive becomes free, this set can be mounted and restored.
- 121
- MESSAGE
STARTING TO RESTORE FILES OF VOLSET ! ON LDEV !
- CAUSE
The files of the specified volume set are now being restored from the specified ldev.
- ACTION
Information only.
- 124
- MESSAGE
RESTORE ASSUMES THAT NEXT VOL OF VOLSET ! IS ON LDEV !
- CAUSE
Even though an error was encountered while reading the label of this volume, the user has instructed that it be used anyway, and restore assumes it is the specified volume.
- ACTION
Information only.
- 125
- MESSAGE
RESTORE ASSUMES THAT MEDIA ! OF VOLSET ! IS ON LDEV !
- CAUSE
Even though an error was encountered while reading the label of this volume, the user has instructed that it be used anyway, and restore assumes it is the specified volume.
- ACTION
Information only.
- 126
- MESSAGE
RESTORE ASSUMES THAT VOL ! OF VOLSET ! IS ON LDEV !
- CAUSE
Even though an error was encountered while reading the label of this volume, the user has instructed that it be used anyway, and restore assumes it is the specified volume.
- ACTION
Information only.
- 127
- MESSAGE
USE DAMAGED MEDIA AS NEXT VOLUME OF SET ! ON LDEV ! (Y/N)
- CAUSE
An error was encountered while reading the label of this volume.
- ACTION
Reply Yes to the console request if this volume should be used anyway. Reply No to cause this volume to be dismounted.
- 128
- MESSAGE
USE DAMAGED MEDIA AS MEDIA ! OF SET ! ON LDEV !(Y/N)
- CAUSE
An error was encountered while reading the label of this volume.
- ACTION
Reply Yes to the console request if this volume should be used anyway. Reply No to cause this volume to be dismounted.
- 129
- MESSAGE
USE DAMAGED MEDIA AS VOL ! OF SET ! ON LDEV !(Y/N)
- CAUSE
An error was encountered while reading the label of this volume.
- ACTION
Reply Yes to the console request if this volume should be used anyway. Reply No to cause this volume to be dismounted.
- 130
- MESSAGE
MOUNT NEXT MEMBER OF VOLSET ! FOR RESTORE ON LDEV !
- CAUSE
Restore needs the next member of the specified volume set.
- ACTION
Find and mount the next member of the specified volume set on the specified ldev.
- 131
- MESSAGE
MOUNT MEDIA ! OF VOLSET ! FOR RESTORE ON LDEV !
- CAUSE
Restore needs a specific member of the specified volume set.
- ACTION
Find and mount the requested media on the specified ldev.
- 132
- MESSAGE
MOUNT VOL ! OF VOLSET ! FOR RESTORE ON LDEV !
- CAUSE
Restore needs a specific volume from a specific volume set.
- ACTION
Find and mount the requested volume on the specified ldev.
- 133
- MESSAGE
VOLUME OF SET ! ON LDEV ! INCORRECT. USE IT? (Y/N)
- CAUSE
An unexpected labeled volume was mounted for restore.
- ACTION
Reply Yes to the console message to have restore use this volume. All files that were on unmounted volumes previous to this one will not be restore. Reply No to cause this volume to be dismounted.
- 134
- MESSAGE
MEDIA ! OF SET ! ON LDEV ! INCORRECT. USE IT? (Y/N)
- CAUSE
An unexpected labeled volume was mounted for restore.
- ACTION
Reply Yes to the console message to have restore use this volume. All files that were on unmounted volumes previous to this one will not be restore. Reply No to cause this volume to be dismounted.
- 135
- MESSAGE
VOL ! OF SET ! ON LDEV ! INCORRECT. USE IT? (Y/N)
- CAUSE
An unexpected labeled volume was mounted for restore.
- ACTION
Reply Yes to the console message to have restore use this volume. All files that were on unmounted volumes previous to this one will not be restore. Reply No to cause this volume to be dismounted.
- 136
- MESSAGE
MEMBER OF VOLSET ! ON LDEV ! IS NOT A STORE MEDIA
- CAUSE
A non-store labeled volume was mounted for restore.
- ACTION
Only store media can be read by NM Restore.
- 137
- MESSAGE
MEDIA ! OF VOLSET ! ON LDEV ! IS NOT A STORE MEDIA
- CAUSE
A non-store labeled volume was mounted for restore.
- ACTION
Only store media can be read by NM Restore.
- 138
- MESSAGE
VOL ! OF VOLSET ! ON LDEV ! IS NOT A STORE MEDIA
- CAUSE
A non-store labeled volume was mounted for restore.
- ACTION
Only store media can be read by NM Restore.
- 139
- MESSAGE
VOLUME OF VOLSET ! ON LDEV ! IS ALLOCATED TO ANOTHER DRIVE
- CAUSE
The volume that has been mounted belongs to a parallel restoreset that is already being restored on another device.
- ACTION
Dismount this volume and mount a volume that does not belong to an already allocated restoreset.
- 140
- MESSAGE
MEDIA ! OF VOLSET ! ON LDEV ! IS ALLOCATED TO ANOTHER DRIVE
- CAUSE
The volume that has been mounted belongs to a parallel restoreset that is already being restored on another device.
- ACTION
Dismount this volume and mount a volume that does not belong to an already allocated restoreset.
- 141
- MESSAGE
VOL ! OF VOLSET ! ON LDEV ! IS ALLOCATED TO ANOTHER DRIVE
- CAUSE
The volume that has been mounted belongs to a parallel restoreset that is already being restored on another device.
- ACTION
Dismount this volume and mount a volume that does not belong to an already allocated restoreset.
- 142
- MESSAGE
VOLUME NOT MEMBER OF VOLSET ! ; DISMOUNTED BY RESTORE ON LDEV !
- CAUSE
The wrong labeled volume has been mounted for this restore.
- ACTION
This volume is being dismounted. The next console message will specify which volume should be mounted.
- 143
- MESSAGE
VOLUME NOT MEMBER OF VOLSET ! ; DISMOUNTED BY RESTORE ON LDEV !
- CAUSE
The wrong labeled volume has been mounted for this restore.
- ACTION
This volume is being dismounted. The next console message will specify which volume should be mounted.
- 144
- MESSAGE
VOLUME NOT MEMBER OF VOLSET ! ; DISMOUNTED BY RESTORE ON LDEV !
- CAUSE
The wrong labeled volume has been mounted for this restore.
- ACTION
This volume is being dismounted. The next console message will specify which volume should be mounted.
- 145
- MESSAGE
MEMBER OF VOLSET ! ON LDEV ! IS PRIOR TO THAT REQUESTED
- CAUSE
A volume which has already be restored from, or which is no longer needed, has been mounted.
- ACTION
Dismount this volume and mount the previously requested volume.
- 146
- MESSAGE
MEDIA ! OF VOLSET ! ON LDEV ! IS PRIOR TO THAT REQUESTED
- CAUSE
A volume which has already be restored from, or which is no longer needed, has been mounted.
- ACTION
Dismount this volume and mount the previously requested volume.
- 147
- MESSAGE
VOL ! OF VOLSET ! ON LDEV ! IS PRIOR TO THAT REQUESTED
- CAUSE
A volume which has already be restored from, or which is no longer needed, has been mounted.
- ACTION
Dismount this volume and mount the previously requested volume.
- 148
- MESSAGE
VOL ID GIVEN FOR MEMBER OF VOLSET ! ON LDEV ! IS INVALID
- CAUSE
The volume id of this volume is incorrect.
- ACTION
Dismount this volume and mount a volume from the specified volume set.
- 152
- MESSAGE
LABEL TYPE CLASH BETWEEN VOLSET ! AND VOLUME ON LDEV !
- CAUSE
Either an ANSI labeled volume was mounted when an IBM label was expected, or vice versa.
- ACTION
Mount a type-compatible labeled volume.
- 153
- MESSAGE
LABEL TYPE CLASH BETWEEN VOLSET ! AND VOLUME ON LDEV !
- CAUSE
Either an ANSI labeled volume was mounted when an IBM label was expected, or vice versa.
- ACTION
Mount a type-compatible labeled volume.
- 154
- MESSAGE
LABEL TYPE CLASH BETWEEN VOLSET ! AND VOLUME ON LDEV !
- CAUSE
Either an ANSI labeled volume was mounted when an IBM label was expected, or vice versa.
- ACTION
Mount a type-compatible labeled volume.
- 155
- MESSAGE
REPLY WITH VOL ID FOR MEMBER OF VOLSET !
- CAUSE
A new labeled volume needs a volume id.
- ACTION
Reply to the console message with the new volume id for this volume.
- 156
- MESSAGE
REPLY WITH VOL ID FOR MEDIA ! OF VOLSET !
- CAUSE
A new labeled volume needs a volume id.
- ACTION
Reply to the console message with the new volume id for this volume.
- 157
- MESSAGE
VOLUME OF VOLSET ! ON LDEV ! IS BEING MARKED BAD
- CAUSE
A media error occurred while writing to this volume. The volume will be marked bad to indicate there was an error while writing to it.
- ACTION
After store has marked this volume bad, dismount it and mount a new volume.
- 158
- MESSAGE
MEDIA ! OF VOLSET ! ON LDEV ! IS BEING MARKED BAD
- CAUSE
A media error occurred while writing to this volume. The volume will be marked bad to indicate there was an error while writing to it.
- ACTION
After store has marked this volume bad, dismount it and mount a new volume.
- 159
- MESSAGE
VOL ! OF VOLSET ! ON LDEV ! IS BEING MARKED BAD
- CAUSE
A media error occurred while writing to this volume. The volume will be marked bad to indicate there was an error while writing to it.
- ACTION
After store has marked this volume bad, dismount it and mount a new volume.
- 160
- MESSAGE
MOUNT NEXT MEMBER FOR VOLSET ! FOR STORE ON LDEV !
- CAUSE
Store has finished writing to the current volume and needs the next volume.
- ACTION
Dismount the current volume and mount the next volume for the volume set on the specified ldev.
- 161
- MESSAGE
MOUNT MEDIA ! FOR VOLSET ! FOR STORE ON LDEV !
- CAUSE
Store has finished writing to the current volume and needs the next volume.
- ACTION
Dismount the current volume and mount the next media for the volume set on the specified ldev.
- 162
- MESSAGE
MOUNT VOL ! FOR VOLSET ! FOR STORE ON LDEV !
- CAUSE
Store has finished writing to the current volume and needs the next volume.
- ACTION
Dismount the current volume and mount the specified volume for the volume set on the specified ldev.
- 163
- MESSAGE
STARTING TO WRITE TO MEMBER OF VOLSET ! ON LDEV !
- CAUSE
Store is being to write to a member of the specified volume set.
- ACTION
Information only.
- 164
- MESSAGE
STARTING TO WRITE TO MEDIA ! OF VOLSET ! ON LDEV !
- CAUSE
Store is being to write to a member of the specified volume set.
- ACTION
Information only.
- 165
- MESSAGE
STARTING TO WRITE TO VOL ! OF VOLSET ! ON LDEV !
- CAUSE
Store is being to write to a member of the specified volume set.
- ACTION
Information only.
- 166
- MESSAGE
MEMBER OF VOLSET ! ON LDEV ! IS PART OF CURRENT STORE SET
- CAUSE
A volume that has already been written to as part of this backup was re-mounted.
- ACTION
Dismount this volume and mount a volume that has not yet been written to as part of this store.
- 167
- MESSAGE
MEDIA ! OF VOLSET ! ON LDEV ! IS PART OF CURRENT STORE SET
- CAUSE
A volume that has already been written to as part of this backup was re-mounted.
- ACTION
Dismount this volume and mount a volume that has not yet been written to as part of this store.
- 168
- MESSAGE
VOL ! OF VOLSET ! ON LDEV ! IS PART OF CURRENT STORE SET
- CAUSE
A volume that has already been written to as part of this backup was re-mounted.
- ACTION
Dismount this volume and mount a volume that has not yet been written to as part of this store.
- 169
- MESSAGE
OK TO RE-LABEL EXPIRED VOLUME ! (Y/N)
- CAUSE
An expired volume with a different volume set id has been mounted for a store.
- ACTION
Reply Yes if it is ok to relabel this volume. Reply No if this volume should not be overwritten.
- 170
- MESSAGE
OK TO RE-LABEL EXPIRED VOLUME ! AS ! (Y/N)
- CAUSE
An expired volume with a different volume set id has been mounted for a store.
- ACTION
Reply Yes if it is ok to relabel this volume. Reply No if this volume should not be overwritten.
- 171
- MESSAGE
OK TO RE-LABEL EXPIRED VOLUME ! AS ! (Y/N)
- CAUSE
An expired volume with a different volume set id has been mounted for a store.
- ACTION
Reply Yes if it is ok to relabel this volume. Reply No if this volume should not be overwritten.
- 172
- MESSAGE
STORE CANNOT OVERWRITE UNEXPIRED VOLUME ! ON LDEV# \
- CAUSE
An unexpired volume was mounted for a store.
- ACTION
Dismount this volume and mount a volume that has expired.
- 173
- MESSAGE
STORE CANNOT OVERWRITE UNEXPIRED VOLUME ! ON LDEV# \
- CAUSE
An unexpired volume was mounted for a store.
- ACTION
Dismount this volume and mount a volume that has expired.
- 174
- MESSAGE
STORE CANNOT OVERWRITE UNEXPIRED VOLUME ! ON LDEV# \
- CAUSE
An unexpired volume was mounted for a store.
- ACTION
Dismount this volume and mount a volume that has expired.
- 175
- MESSAGE
MEMBER OF VOLSET ! ON LDEV ! HAS INCORRECT HDR LABELS
- CAUSE
A volume mounted for restore has incorrect HDR1 labels.
- ACTION
Mount a valid volume of the specified volume set.
- 176
- MESSAGE
MEDIA ! OF VOLSET ! ON LDEV ! HAS INCORRECT HDR LABELS
- CAUSE
A volume mounted for restore has incorrect HDR1 labels.
- ACTION
Mount a valid volume of the specified volume set.
- 177
- MESSAGE
VOL ! OF VOLSET ! ON LDEV ! HAS INCORRECT HDR LABELS
- CAUSE
An unexpired volume was mounted for a store.
- ACTION
Dismount this volume and mount a volume that has expired.
- 185
- MESSAGE
MAKE UNLABELED MEDIA ON LDEV ! PART OF LABELED SET (Y/N)
- CAUSE
An unlabeled media has been mounted for a labeled store.
- ACTION
Reply Yes to the console request if this unlabeled media should be converted to a labeled volume.
- 186
- MESSAGE
MAKE UNLABELED MEDIA ON LDEV ! PART OF LABELED SET (Y/N)
- CAUSE
An unlabeled media has been mounted for a labeled store.
- ACTION
Reply Yes to the console request if this unlabeled media should be converted to a labeled volume.
- 187
- MESSAGE
MAKE UNLABELED MEDIA ON LDEV ! PART OF LABELED SET (Y/N)
- CAUSE
An unlabeled media has been mounted for a labeled store.
- ACTION
Reply Yes to the console request if this unlabeled media should be converted to a labeled volume.
- 188
- MESSAGE
VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED
- CAUSE
A different labeled volume than the one requested was mounted for a store.
- ACTION
Dismount this volume and mount the requested volume.
- 189
- MESSAGE
VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED
- CAUSE
A different labeled volume than the one requested was mounted for a store.
- ACTION
Dismount this volume and mount the requested volume.
- 190
- MESSAGE
VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED
- CAUSE
A different labeled volume than the one requested was mounted for a store.
- ACTION
Dismount this volume and mount the requested volume.
- 191
- MESSAGE
RESTORE SKIPPING SLT IN PROGRESS ON LDEV !
- CAUSE
Restore is skipping over the SLT portion of combined SLT/Store.
- ACTION
Information only.
- 198
- MESSAGE
OK TO RESTORE FILES OF SET ! ON LDEV ! (Y/N)
- CAUSE
Restore needs verification that the specified restoreset should be restored from the MO at the specified ldev.
- ACTION
Reply "Yes" to the console message if this is the set that should be restored. Reply "No" otherwise.
Store/Restore Messages 200 - 399
- 203
- MESSAGE
ARE ALL FILES AND DATABASES QUIESCED FOR ONLINE BACKUP #! ? (Y/N)
- CAUSE
You have specified the ASK parameter to the ONLINE option, requesting that TurboSTORE notify via a console request when the True-Online sync point is about to occur.
- ACTION
Make sure that all non-HP databases and other files are ready for the sync point. Then, reply Y to this request if you want the sync point to occur. If you want to cancel this backup, reply N.
- 206
- MESSAGE
DO YOU WANT TO ABORT THE BACKUP? (Y/N)
- CAUSE
You have replied "N" to the ASK request during a True-Online backup.
- ACTION
If you reply "Y" to this message, the backup will abort and will be invalid. If you reply "N" to this message, you will be asked if all files and databases are quiesced for an online backup.
- 209
- MESSAGE
ONLINE BACKUP SYNC POINT STARTING
- CAUSE
TurboSTORE is starting to quiesce all databases specified for a True-Online backup.
- ACTION
None required, information only. You may notice a pause in database access during the online sync point for all databases being stored by a 7x24 online backup.
- 212
- MESSAGE
ONLINE BACKUP SYNC POINT FINISHED
- CAUSE
TurboSTORE has completed the 7x24 online sync point and has unquiesced all databases.
- ACTION
None required, information only. Users should be able to access quiesced databases now.
- 215
- MESSAGE
ALL NON-STANDARD DATABASES CAN BE UNQUIESCED NOW
- CAUSE
The 7x24 online sync point has completed.
- ACTION
If you had to manually quiesce any non-HP databases, they can now be unquiesced.
- 218
- MESSAGE
MOUNT LAST MEDIA FOR RESTORE ON LDEV \
- CAUSE
RESTORE needs to read the final media directory from the last media of the backup.
- ACTION
Mount the last media of the backup.
- 221
- MESSAGE
MOUNT LAST MEMBER OF VOLSET ! FOR RESTORE ON LDEV \
- CAUSE
RESTORE needs to read the final media directory from the last media of the backup.
- ACTION
Mount the last volume of the specified volume set.
- 224
- MESSAGE
STORE/RESTORE ENCOUNTERED A POWERFAIL ON LDEV !
- CAUSE
A powerfail or bus reset occurred on the specified LDEV
- ACTION
If this was reported from STORE, STORE will automatically rewind the current media and rewrite the data. If this is reported by RESTORE, the RESTORE will abort, since RESTORE cannot recover from a device powerfail.
- 225
- MESSAGE
STORE/RESTORE ENCOUNTERED A POWERFAIL ON REMOTE DEVICE FILE "!"
- CAUSE
A powerfail or bus reset occurred on the specified remove device
- ACTION
If this was reported from STORE, STORE will automatically rewind the current media and rewrite the data. If this is reported by RESTORE, the RESTORE will abort, since RESTORE cannot recover from a device powerfail.
- 227
- MESSAGE
STORE/RESTORE LOST TAPE TENSION ON LDEV !
- CAUSE
While accessing a device, a tape tension lost condition was reported.
- ACTION
STORE try to recover from this situation by rewinding the current media and rewriting the reel. RESTORE cannot recover from such a situation and will abort. Make sure your tape devices are clean.
- 228
- MESSAGE
STORE/RESTORE LOST TAPE TENSION ON REMOTE DEVICE FILE "!"
- CAUSE
While accessing a remote device, a tape tension lost condition was reported.
- ACTION
STORE try to recover from this situation by rewinding the current media and rewriting the reel. RESTORE cannot recover from such a situation and will abort. Make sure your tape devices are clean.
- 301
- MESSAGE
WARNING: 'FILES' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 301)
- CAUSE
The FILES option was entered more than once.
- ACTION
Information only.
- 302
- MESSAGE
EXPECTED '={maxfiles}' AFTER 'FILES' OPTION.
SYNTAX 'FILES={maxfiles}' (S/R 302)- CAUSE
You did not type the files parameter correctly.
- ACTION
Check the syntax and retype the command.
- 303
- MESSAGE
SPECIFIED MAXFILES VALUE FOR 'FILES={maxfiles}' EXCEEDS THE MAXIMUM ALLOWED. (S/R 303)
- CAUSE
The maximum files limit of the files parameter has been exceeded.
- ACTION
Information only.
- 304
- MESSAGE
EXPECTED 'FILES={maxfiles}' WHERE {maxfiles} IS A POSITIVE INTEGER. (S/R 304)
- CAUSE
You have specified a negative 'maxfiles' number.
- ACTION
Information only.
- 305
- MESSAGE
'FILES' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 305)
- CAUSE
The files and listdir options are not allowed on the same command line.
- ACTION
Delete either the files or the listdir options.
- 311
- MESSAGE
'RESTORESET' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 311)
- CAUSE
You entered RESTORESET twice in the command.
- ACTION
Remove one of the RESTORESET options and retype the command.
- 312
- MESSAGE
'RESTORESET' OPTION MAY NOT BE SPECIFIED IN CONJUNCTION WITH A POSITIONAL DEVICE FILE. Ex. 'RESTORE *t;....;RESTORESET=(*t1,*t2)' IS INVALID. (S/R 312)
- CAUSE
Restoreset and device file options are not allowed on the same command line.
- ACTION
Delete either restoresest or device file options and retype the command.
- 313
- MESSAGE
EXPECTED '=(device[,,..])[,(device[,...])]' AFTER 'RESTORESET' OPTION.
SYNTAX 'RESTORESET=(device[,..])[,(device[,...])]'.
(S/R 313)- CAUSE
You did not type the restoreset parameter correctly.
- ACTION
Check the syntax and retype the command.
- 314
- MESSAGE
EXPECTED A '(' TO START A RESTORESET. Ex. 'RESTORESET=(*ta,*tb).
SYNTAX 'RESTORE-SET=(device[,...])[device[,...])]' (S/R 314)- CAUSE
You did not include a left parenthesis.
- ACTION
Check the syntax and retype the command.
- 315
- MESSAGE
MAXIMUM NUMBER OF PARALLEL SETS EXCEEDED FOR 'RESTORESET' OPTION. Ex, 'RESTORESET=(*ta),(*tb)' IS TWO PARALLEL SETS. (S/R 315)
- CAUSE
You specified too many parallel sets. The maximum is 8.
- ACTION
Specify 8 or fewer parallel sets.
- 316
- MESSAGE
EXPECTED 'device' FILE EQUATION IN RESTORESET. Ex. RESTORESET=(*t)
SYNTAX 'RESTORESET=(device[,..])[,(device[,...])]'. (S/R 316)- CAUSE
You did not include a file equation to name the backup device.
- ACTION
Specify a file equation.
- 317
- MESSAGE
MAXIMUM NUMBER OF 'device" FILE EQUATIONS EXCEEDED FOR A SERIAL SET. Ex. RESTORESET = (*t1, *t2,..., *tn) EXCEEDS THE MAXIMUM OF 8. (S/R 317)
- CAUSE
You specified too many serial file equations. The maximum is 8.
- ACTION
Specify 8 or fewer serial file equation.
- 318
- MESSAGE
EXPECTED A ')' TO TERMINATE A SERIAL THE 'RESTORESET' OPTION.
SYNTAX 'RESTORESET=(device[,...])[device[,...])]' (S/R 318)- CAUSE
You did not include a right parenthesis.
- ACTION
Check the syntax and retype the command.
- 319
- MESSAGE
'RESTORESET' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 319)
- CAUSE
Restoreset and listdir options are not allowed on the same command line.
- ACTION
Delete either restoreset or listdir option and retype the command.
- 320
- MESSAGE
'RESTORESET' OPTION NOT ALLOWED FOR A SLT/STORE SET (S/R 320)
- CAUSE
The restoreset option cannot be used with a combined SLT/ store set tape.
- ACTION
Redo the restore command, using only one backup device, and not specifying the restoreset option.
- 321
- MESSAGE
WARNING: 'PROGRESS' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 321)
- CAUSE
The PROGRESS option was entered more than once.
- ACTION
Information only.
- 322
- MESSAGE
EXPECTED {#minutes} BETWEEN 1 AND 60.
SYNTAX PROGRESS[={#minutes}] (S/R 322)- CAUSE
You did not specify a number within the range.
- ACTION
Specify a number between 1 and 60.
- 323
- MESSAGE
EXPECTED 'PROGRESS={#minutes}' WHERE {#minutes} IS A POSITIVE INTEGER. (S/R 323)
- CAUSE
The progress parameter must be greater than zero.
- ACTION
Check your syntax and retype the command.
- 324
- MESSAGE
EXPTECTED '={#minutes}' AFTER 'PROGRESS' OPTION. (S/R 324)
- CAUSE
You did not type the progress parameter correctly.
- ACTION
Check the syntax and retype the command.
- 331
- MESSAGE
'STORESET' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 331)
- CAUSE
You cannot specify the storeset and transport parameters on the same command line.
- ACTION
Delete either the storeset or the transport parameter from the command line.
- 332
- MESSAGE
'STORESET' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 332)
- CAUSE
You entered STORESET twice in the command.
- ACTION
Delete one of the STORESET options and retype the command.
- 333
- MESSAGE
'STORESET' OPTION MAY NOT BE SPECIFIED IN CONJUNCTION WITH A POSITIONAL DEVICE FILE. EG 'STORE...;*t;STORESET=(*t1,*t2)' IS VALID. (S/R 333)
- CAUSE
You mistyped the storeset parameter.
- ACTION
Check the syntax of the storeset parameter and retype the command.
- 334
- MESSAGE
EXPECTED '=(device[,,..])[,(device[,...])]' AFTER 'STORESET' OPTION.
SYNTAX 'STORESET=(device[,..])[,(device[,...])]' (S/R 334)- CAUSE
You did not type the storeset parameter correctly.
- ACTION
Check the syntax and retype the command.
- 335
- MESSAGE
EXPECTED A '(' TO START A STORESET. Ex. 'STORESET=(*ta,*tb).
SYNTAX 'STORESET=(device[,...])[,(device[,...])]' (S/R 336)- CAUSE
You did not include the left parenthesis in your command.
- ACTION
Check the syntax and retype the command.
- 336
- MESSAGE
EXPECTED 'device' FILE EQUATION IN STORESET. Ex. STORESET=(*ta,*tb
SYNTAX 'STORESET=(device[,..])[,(device[,...])]' (S/R 336)- CAUSE
You did not specify a file equation to name the backup device.
- ACTION
Specify the file equation.
- 337
- MESSAGE
MAXIMUM NUMBER OF 'device' FILE EQUATIONS EXCEEDED FOR A SERIAL SET. Ex. STORESET=(*t1,*t2,...*tn) EXCEEDS THE MAXIMUM OF 8. (S/R 337)
- CAUSE
You specify too many serial file equations. the maximum is 8.
- ACTION
Specify 8 or fewer serial file equations.
- 338
- MESSAGE
EXPECTED A ')' TO TERMINATE A SERIAL THE 'STORESET' OPTION.
SYNTAX 'STORESET=(device[,...])[(device[,...])]' (S/R 338)- CAUSE
You did not include a right parenthesis.
- ACTION
Check the syntax and retype the command.
- 339
- MESSAGE
'STORESET' OPTION NOT ALLOWED IN SYSGEN/STORE. (S/R 339)
- CAUSE
A combined SLT/store set cannot be created by sysgen with the storeset option.
- ACTION
Retype the command without the storeset option, specifying only one backup device.
- 351
- MESSAGE
WARNING: 'TRANSPORT' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 351)
- CAUSE
The TRANSPORT option was entered more than once.
- ACTION
Information only.
- 352
- MESSAGE
'TRANSPORT' OPTION NOT ALLOWED IN SYSGEN/STORE. (S/R 352)
- CAUSE
Sysgen cannot created a CMStore format tape.
- ACTION
Remove the transport option from the store options and redo the command.
- 354
- MESSAGE
INVALID TARGET SYSTEM ID FOR 'TRANSPORT' KEYWORD. ONLY ID CURRENTLY VALID IS "MPEXL". IF NO TARGET ID IS SPECIFIED THEN THE TARGET SYSTEM DEFAULTS TO MPEv. SYNTAX: TRANSPORT[=MPEXL] (S/R 354)
- CAUSE
An invalid transport id was specified.
- ACTION
Specify a legel transport option and redo the command.
- 361
- MESSAGE
WARNING: 'DIRECTORY' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 361)
- CAUSE
The DIRECTORY option was entered more than once.
- ACTION
Information only.
- 362
- MESSAGE
'DIRECTORY' OPTION CANNOT BE USED WITH THE 'TRANSPORT' OPTION. (S/R 362)
- CAUSE
Directory and transport options are not allowed on the same command line.
- ACTION
Delete either directory or transport option and retype the command.
- 363
- MESSAGE
USE OF THE 'DIRECTORY' OPTION REQUIRES (SM) OR (OP) CAPABILITY. (S/R 363)
- CAUSE
You do not have system manager (SM) capability or system operator (OP) capability.
- ACTION
Log on to an account with SM or AM, or have your system manager perform the tasks.
- 371
- MESSAGE
'ONVS' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 371)
- CAUSE
ONVS and TRANSPORT options are not allowed on the same command line.
- ACTION
Delete either the ONVS or TRANSPORT option and retype the command.
- 372
- MESSAGE
WARNING: 'ONVS' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 372)
- CAUSE
The ONVS option was entered more than once.
- ACTION
Information only.
- 373
- MESSAGE
EXPECTED '=volumesetname[,volumesetname...]' AFTER 'ONVS' OPTION. (S/R 373)
- CAUSE
You did not type the onvs parameter correctly.
- ACTION
Check the syntax and retype the command.
- 374
- MESSAGE
INVALID VOLUMESET NAME SPECIFIED FOR 'ONVS' OPTION. VOLUMESET NAME MUST START WITH AN ALPHA "A - Z' AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", "_" AND "."
SYNTAX 'ONVS=volumesetname[,volumesetname...]'. (S/R 374)- CAUSE
Volumeset name mispelled or not recognized on the system.
- ACTION
Enter a system recognized volumeset name.
- 375
- MESSAGE
VOLUMESET NAME SPECIFIED FOR 'ONVS' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 32 CHARACTERS.
SYNTAX 'ONVS=volumesetname[,volumesetname...]'. (S/R 375)- CAUSE
You entered a volumeset name that was more than 32 characters.
- ACTION
Enter a volumeset name that has 32 characters or less.
- 376
- MESSAGE
EXPECTED 'volumesetname[,volumesetname...]' AFTER 'ONVS=' WHERE volumesetname IS THE NAME OF THE VOLUME SET THAT IS CURRENTLY ON YOUR SYSTEM.
SYNTAX 'ONVS=volumesetname[,volumesetname...]'. (S/R 376)- CAUSE
You did not type onvs parameter correctly.
- ACTION
Check the syntax and retype the command.
- 377
- MESSAGE
STORE/RESTORE DOES NOT ALLOW MORE THAN TWENTY (20) "volumesetnames" TO BE SPECIFIED FOR THE 'ONVS' OPTION. (S/R 377)
- CAUSE
You specify too many volumeset name with the onvs option. the maximum is 20.
- ACTION
Specify 20 or fewer volumesets.
- 378
- MESSAGE
"volumesetname" SPECIFIED DOES NOT EXIST (IS NOT MOUNTED) ON THIS SYSTEM. (S/R 378)
- CAUSE
You entered a volumeset name which is not on the system.
- ACTION
Enter a correct volumeset name.
- 381
- MESSAGE
'VOLSET' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 381)
- CAUSE
The VOLSET option was entered more than once.
- ACTION
Information only.
- 382
- MESSAGE
'VOLSET' OPTION CANNOT BE USED WITH THE 'DEV' OPTION. (S/R 382)
- CAUSE
Volset and dev options are not allowed on the same command line.
- ACTION
Delete either volset or dev option and retype the command.
- 383
- MESSAGE
EXPECTED '=volumesetname' AFTER 'VOLSET' OPTION.
SYNTAX 'VOLSET=volumesetname'. (S/R 383)- CAUSE
You did not enter the volset parameter correctly.
- ACTION
Check the syntax and retype the command.
- 384
- MESSAGE
INVALID VOLUMESET NAME SPECIFIED FOR 'VOLSET' OPTION. VOLUMESET NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", "_" OR "."
SYNTAX 'VOLSET=volumesetname'. (S/R 384)- CAUSE
Volumeset name mispelled or not recognized on the system.
- ACTION
Enter a system recognized volumeset name.
- 385
- MESSAGE
VOLUMESET NAME SPECIFIED FOR 'VOLSET' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 32 CHARACTERS.
SYNTAX 'VOLSET=volumesetname' (S/R 385)- CAUSE
You entered a volumeset name that was more than 32 characters.
- ACTION
Enter a volumeset name that has 32 characters or less.
- 386
- MESSAGE
EXPECTED 'volumesetname' AFTER 'VOLSET=' WHERE volumesetname IS THE NAME OF A VOLUME SET THAT IS CURRENTLY MOUNTED ON YOUR SYSTEM.
SYNTAX 'VOLSET=volumesetname' (S/R 386)- CAUSE
You did not type the volset parameter correctly.
- ACTION
Check the syntax and retype the command.
- 387
- MESSAGE
'VOLSET' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 387)
- CAUSE
Volset and listdir options are not allowed on the same command line.
- ACTION
Delete either volset or listdir option and retype the command.
- 391
- MESSAGE
'VOLCLASS' OPTION CANNOT BE USED WITH THE 'VOL' OPTION. (S/R 391)
- CAUSE
Volclass and vol options are not allowed on the same command line.
- ACTION
Delete either volclass or vol option and retype the command.
- 392
- MESSAGE
'VOLCLASS' OPTION CANNOT BE USED WITH THE 'DEV' OPTION. (S/R 392)
- CAUSE
Volclass and dev options are not allowed on the same command line.
- ACTION
Delete either volclass or dev option and retype the command.
- 393
- MESSAGE
'VOLCLASS' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 393)
- CAUSE
The VOLCLASS option was entered more than once.
- ACTION
Information only.
- 394
- MESSAGE
EXPECTED '=volumeclassname' AFTER 'VOLCLASS' OPTION.
SYNTAX 'VOLCLASS=volumeclassname' (S/R 394)- CAUSE
You did not type the volclass parameter correctly.
- ACTION
Check the syntax and retype the command.
- 395
- MESSAGE
INVALID VOLUMECLASS NAME SPECIFIED FOR 'VOLCLASS' OPTION. VOLUMECLASS NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_".
SYNTAX 'VOLCLASS=volumeclassname'. (S/R 395)- CAUSE
Volumeclass name mispelled or not recognized on the system.
- ACTION
Enter a system recognized volumeclass name.
- 396
- MESSAGE
VOLUMECLASS NAME SPECIFIED FOR 'VOLCLASS' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 16 CHARACTERS.
SYNTAX 'VOLCLASS=volumeclassname' (S/R 396)- CAUSE
You entered a volumeclass name that was more than 16 characters.
- ACTION
Enter a volumeclass name that has 16 characters or less.
- 397
- MESSAGE
EXPECTED 'volumeclassname' AFTER 'VOLCLASS=' WHERE volumeclassname IS THE NAME OF A VOLUME CLASS THAT IS ON A VOLUME SET CURRENTLY MOUNTED ON YOUR SYSTEM.
SYNTAX 'VOLCLASS=volumeclassname' (S/R 397)- CAUSE
You did not specify a volumeclass name.
- ACTION
Check the syntax and retype the command.
- 398
- MESSAGE
'VOLCLASS' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 398)
- CAUSE
Volclass and listdir options are not allowed on the same command line.
- ACTION
Delete either volclass or listdir option and retype the command.
Store/Restore Messages 400 - 599
- 401
- MESSAGE
'VOL' OPTION CANNOT BE USED WITH THE 'VOLCLASS' OPTION (S/R 401)
- CAUSE
Vol and volclass options are not allowed on the same command line.
- ACTION
Delete either vol or volclass option and retype the command.
- 402
- MESSAGE
'VOL' OPTION CANNOT BE USED WITH THE 'DEV' OPTION (S/R 402)
- CAUSE
Vol and dev options are not allowed on the same command line.
- ACTION
Delete either vol or dev option and retype the command.
- 403
- MESSAGE
'VOL' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 403)
- CAUSE
The VOL option was entered more than once.
- ACTION
Information only.
- 404
- MESSAGE
EXPECTED '=volumename' AFTER 'VOL' OPTION.
SYNTAX 'VOL=volumename' (S/R 404)- CAUSE
You did not type vol parameter correctly.
- ACTION
Check the syntax and retype the command.
- 405
- MESSAGE
INVALID VOLUME NAME SPECIFIED FOR 'VOL' OPTION. VOLUME NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_".
SYNTAX 'VOL=volumename' (S/R 405)- CAUSE
Volume name misspelled or unrecognizable volume name was entered.
- ACTION
Enter the correct volume name.
- 406
- MESSAGE
VOLUME NAME SPECIFIED FOR 'VOL' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 16 CHARACTERS.
SYNTAX 'VOL=volumename' (S/R 406)- CAUSE
The volume name you specified is too long. The maximum number of chharacters is 16.
- ACTION
Specify a volume name with 16 or fewer characters.
- 407
- MESSAGE
EXPECTED 'volumename' AFTER 'VOL=' WHERE volumename IS THE NAME OF A VOLUME (DISC) THAT IS CURRENTLY MOUNTED ON YOUR SYSTEM.
SYNTAX 'VOLSET=volumesetname' (S/R 407)- CAUSE
You did not enter the volumename.
- ACTION
Check the syntax and retype the command.
- 408
- MESSAGE
'VOL' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 408)
- CAUSE
Vol and listdir options are not allowed on the same command line.
- ACTION
Delete either vol or listdir option and retype the command.
- 411
- MESSAGE
WARNING: 'HIGH' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 411)
- CAUSE
The HIGH option was entered more than once.
- ACTION
Information only.
- 412
- MESSAGE
EXPECTED '={datasetnumber}' AFTER 'HIGH' OPTION.
SYNTAX 'HIGH={datasetnumber}' (S/R 412)- CAUSE
You did not specify datasetnumber.
- ACTION
Check the syntax and retype the command.
- 413
- MESSAGE
EXPECTED 'HIGH={datasetnumber}' WHERE {datasetnumber} IS A POSITIVE INTEGER DENOTING A DATA SET BETWEEN 0 AND 199.
SYNTAX 'HIGH={datasetnumber}' (S/R 413)- CAUSE
You did not type the high parameter correctly.
- ACTION
Check the syntax and retype the command.
- 414
- MESSAGE
EXPECTED {datasetnumber} BETWEEN 0 AND 199.
SYNTAX 'HIGH={datasetnumber}' (S/R 414)- CAUSE
You did not specify a number within the range.
- ACTION
Specify a number between 1 and 199.
- 415
- MESSAGE
{datasetnumber} SPECIFIED FOR 'HIGH' OPTION MUST BE GREATER THAN OR EQUAL TO THE VALUE SPECIFIED FOR THE 'LOW' OPTION.
SYNTAX 'HIGH={datasetnumber}' (S/R 415)- CAUSE
The high parameter is too small.
- ACTION
Specify a larger number for the high parameter.
- 421
- MESSAGE
WARNING: 'LOW' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 421)
- CAUSE
The LOW option was entered more than once.
- ACTION
Information only.
- 422
- MESSAGE
EXPECTED '={datasetnumber}' AFTER 'LOW' OPTION.
SYNTAX 'LOW={datasetnumber}' (S/R 422)- CAUSE
You did not specify datasetnumber.
- ACTION
Check the syntax and retype the command.
- 423
- MESSAGE
EXPECTED 'LOW={datasetnumber}' WHERE {datasetnumber} IS A POSITIVE INTEGER DENOTING A DATA SET BETWEEN 0 AND 199.
SYNTAX 'LOW={datasetnumber}' (S/R 423)- CAUSE
You did not specify a number within the range.
- ACTION
Specify a number between 1 and 199.
- 424
- MESSAGE
{datasetnumber} SPECIFIED FOR 'LOW' OPTION MUST BE LESS THAN OR EQUAL TO THE VALUE SPECIFIED FOR THE 'HIGH' OPTION.
SYNTAX 'LOW={datasetnumber}' (S/R 424)- CAUSE
The low parameter is too large.
- ACTION
Specify a smaller number for low parameter.
- 425
- MESSAGE
EXPECTED {datasetnumber} BETWEEN 0 AND 199.
SYNTAX 'LOW={datasetnumber}' (S/R 425)- CAUSE
You did not specify a number within the range.
- ACTION
Specify a number between 1 and 199.
- 431
- MESSAGE
'FCRANGE' OPTION CANNOT BE USED WITH 'TRANSPORT' to MPEv (S/R 431)
- CAUSE
Fcrange and transport options are not allowed on the same command line.
- ACTION
Delete either fcrange or transport option and retype the command.
- 432
- MESSAGE
WARNING: 'FCRANGE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 432)
- CAUSE
The FCRANGE option was entered more than once.
- ACTION
Information only.
- 433
- MESSAGE
EXPECTED '=filecode/filecode[,filecode/filecode...]' AFTER 'FCRANGE' OPTION.
SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 433)- CAUSE
You typed the fcrange parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 434
- MESSAGE
EXPECTED filecode IN FIRST PART OF filecode/filecode OF 'FCRANGE' OPTION TO BE AN INTEGER BETWEEN -32768 AND 32767.
SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 434)- CAUSE
You typed the fcrange parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 435
- MESSAGE
SPECIFIED filecode OF 'FCRANGE' OPTION MUST BE AN INTEGER BETWEEN -32768 AND 32767.
SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 435)- CAUSE
You did not enter a valid file code range.
- ACTION
Enter a valid file code range.
- 436
- MESSAGE
EXPECTED A "/" TO SEPARATE filecode RANGES FOR THE 'FCRANGE' OPTION.
SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 436)- CAUSE
You typed the fcrange parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 437
- MESSAGE
EXPECTED filecode IN SECOND HALF OF filecode/filecode OF 'FCRANGE OPTION TO BE AN INTEGER BETWEEN -32768 AND 32767.
SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 437)- CAUSE
You typed the fcrange parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 438
- MESSAGE
SECOND filecode OF A filecode/filecode PAIR IN THE 'FCRANGE' OPTION MUST BE GREATER THAN THE FIRST, Ex. 'FCRANGE=1030/1061'.
SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 438)- CAUSE
The second file code that you specified was lower than the first.
- ACTION
Retype the command so that the second file code is higher than the first.
- 439
- MESSAGE
MAXIMUM NUMBER OF filecode RANGES (8) EXCEEDED FOR THE FCRANGE OPTION (S/R 439)
- CAUSE
You specified too many file code ranges. The maximum number is 8.
- ACTION
Specify 8 or fewer file code ranges.
- 440
- MESSAGE
'FCRANGE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 440)
- CAUSE
Fcrange and listdir options are not allowed on the same command line. .
- ACTION
Delete either fcrange or listdir option and retype the command.
- 441
- MESSAGE
WARNING: 'ONERROR' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 441)
- CAUSE
The ONERROR option was entered more than once.
- ACTION
Information only.
- 442
- MESSAGE
EXPECTED '={error-parm}' AFTER 'ONERROR' OPTION WHERE error-parm IS ONE OF 'QUIT' OR 'SKIP'.
SYNTAX 'ONERR[OR]={QUIT} OR {SKIP}' (S/R 442)- CAUSE
You typed the onerror parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 443
- MESSAGE
THE 'FULL' PARAMETER OF THE 'ONERROR' OPTION REQUIRES (PM) CAPABILITY (S/R 443)
- CAUSE
You do not have PM capability.
- ACTION
Log on to an account with PM capability.
- 444
- MESSAGE
UNKNOWN PARAMETER SPECIFIED FOR THE 'ONERROR' OPTION. EXPECTED ONE OF 'QUIT' OR 'SKIP'.
SYNTAX 'ONERR[OR]={QUIT} OR {SKIP}' (S/R 444)- CAUSE
You did not specify a valid onerror option.
- ACTION
Retype the command and specify a valid onerror option.
- 445
- MESSAGE
EXPECTED recovery type FOR THE 'ONERROR' OPTION. EXPECTED ONE OF 'QUIT' OR 'SKIPFULL'. SYNTAX 'ONERR[OR]={QUIT} OR {SKIP}' (S/R 445)
- CAUSE
You typed the onerror parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 446
- MESSAGE
'ONERROR' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 446)
- CAUSE
Onerror and listdir options are not allowed on the same command line.
- ACTION
Delete either onerror or listdir option and retype the command.
- 447
- MESSAGE
'ONERROR=FULL' FUNCTION NOT IMPLEMENTED (S/R 447)
- CAUSE
Onerror=full will be supported in the future release.
- ACTION
Information only.
- 451
- MESSAGE
WARNING: 'SHOW' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 451)
- CAUSE
The SHOW option was entered more than once.
- ACTION
Information only.
- 452
- MESSAGE
EXPECTED '=showparm[,showparm..]' AFTER 'SHOW' OPTION WHERE showparm IS ONE OF 'SHORT', 'LONG', 'DATES', 'OFFLINE', OR 'SECURITY'.
SYNTAX 'SHOW=showparm[,showparm....]' (S/R 452)- CAUSE
You typed the show parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 453
- MESSAGE
'SHORT' AND 'LONG' PARAMETERS OF THE 'SHOW' OPTION HAVE BEEN MERGED. THE FIRST SPECIFIED (LONG) WILL BE USED (S/R 453)
- CAUSE
Show=long will be used.
- ACTION
Information only.
- 454
- MESSAGE
'SHORT' AND 'LONG' PARAMETERS OF THE 'SHOW' OPTION HAVE BEEN MERGED. THE FIRST SPECIFIED (SHORT) WILL BE USED (S/R 454)
- CAUSE
Show=short will be used.
- ACTION
Information only.
- 455
- MESSAGE
UNKNOWN PARAMETER SPECIFIED FOR THE 'SHOW' OPTION. EXPECTED ONE OF 'SHORT', 'LONG', 'DATES', 'OFFLINE', 'PATH', OR 'SECURITY'.
SYNTAX 'SHOW=showparm[,showparm....]' (S/R 455)- CAUSE
You did not type a valid show parameters.
- ACTION
Check the syntax and retype the command.
- 456
- MESSAGE
EXPECTED showparm FOR THE 'SHOW' OPTION. EXPECTED ONE OF 'SHORT', 'LONG', 'DATES', 'OFFLINE', 'PATH', OR 'SECURITY'.
SYNTAX 'SHOW=showparm[,showparm....]' (S/R 456)- CAUSE
You type the show parameters incorrectly.
- ACTION
Check the syntax and retype the command.
- 457
- MESSAGE
'SHOW' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 457)
- CAUSE
Show and listdir options are not allowed on the same command line.
- ACTION
Delete either show or listdir option and retype the command.
- 458
- MESSAGE
'SHORT' OPTION CANNOT BE USED WITH THE 'NAMESONLY' OPTION (S/R 458)
- CAUSE
The namesonly and short suboptions to SHOW cannot be used together.
- ACTION
Retype the command, specifying only one of short or namesonly.
- 459
- MESSAGE
'LONG' OPTION CANNOT BE USED WITH THE 'NAMESONLY' OPTION (S/R 459)
- CAUSE
The namesonly and long suboptions to SHOW cannot be used together.
- ACTION
Retype the command, specifying only one of long or namesonly.
- 461
- MESSAGE
WARNING: 'DEV' OPTION HAS BEEN REDUNDANTLY SPECIFIED. LAST SPECIFIED 'DEV' WILL BE USED. (S/R 461)
- CAUSE
The DEV option was entered more than once.
- ACTION
Information only.
- 462
- MESSAGE
'DEV' OPTION CANNOT BE USED WITH THE 'VOL' OPTION. (S/R 462)
- CAUSE
Dev and vol options are not allowed on the same command line.
- ACTION
Delete either dev or vol option and retype the command.
- 463
- MESSAGE
'DEV' OPTION CANNOT BE USED WITH THE 'VOLCLASS' OPTION. (S/R 463)
- CAUSE
Dev and volclass options are not allowed on the same command line.
- ACTION
Delete either dev or volclass option and retype the command.
- 464
- MESSAGE
'DEV' OPTION CANNOT BE USED WITH THE 'VOLSET' OPTION. (S/R 464)
- CAUSE
Dev and volset options are not allowed on the same command line.
- ACTION
Delete either dev or volset option and retype the command.
- 465
- MESSAGE
EXPECTED '=ldn' OR '=deviceclass' AFTER 'DEV' OPTION, WHERE ldn IS A LOGICAL DEVICE NUMBER OF A MOUNTED DISC VOLUME AND deviceclass IS THE NAME OF A VOLUME CLASS THAT IS ON A VOLUME SET CURRENTLY MOUNTED ON YOUR SYSTEM.
SYNTAX 'DEV=device' WHERE device IS AN ldn OR A deviceclass. (S/R 465)- CAUSE
You did not include a ldn or deviceclass after the dev option.
- ACTION
Retype the command and include ldn or deviceclass.
- 466
- MESSAGE
THE SPECIFIED ldn (LOGICAL DEVICE NUMBER) DOES NOT CORRESPOND TO THE DISC VOLUME THAT IS CURRENTLY MOUNTED ON THE SYSTEM. TO BE MOUNTED, THE VOLUME MUST BE A MEMBER OF AN "OPENED" VOLUME SET (S/R 466)
- CAUSE
The system does not recognize ldev number specified.
- ACTION
Enter the correct ldev number and try again.
- 467
- MESSAGE
INVALID DEVICECLASS NAME SPECIFIED FOR 'DEV' OPTION. A DEVICECLASS NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_".
SYNTAX 'DEV=device' WHERE device IS AN ldn OR A deviceclass (S/R 467)- CAUSE
The deviceclass name is misspelled or not recognized by the system.
- ACTION
Retype the command using a valid name.
- 468
- MESSAGE
DEVICECLASS NAME SPECIFIED FOR 'DEV' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 16 CHARACTERS.
SYNTAX 'DEV=device' WHERE device IS AN ldn OR A deviceclass. (S/R 468)- CAUSE
You entered deviceclass name that was more than 16 characters.
- ACTION
Enter a deviceclass name that has 16 characters or less.
- 469
- MESSAGE
EXPECTED 'ldn' OR 'deviceclass' AFTER 'DEV=' IN 'DEV' OPTION. WHERE ldn is A LOGICAL DEVICE NUMBER OF A MOUNTED DISC VOLUME AND deviceclass IS THE NAME OF A VOLUME CLASS THAT IS ON A VOLUME SET CURRENTLY MOUNTED ON YOUR SYSTEM. A DEVICECLASS NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_".
SYNTAX 'DEV=device' WHERE device IS AN ldn OR A deviceclass (S/R 469)- CAUSE
You type the dev parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 470
- MESSAGE
'DEV' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 470)
- CAUSE
Dev and listdir options are not allowed on the same command line.
- ACTION
Delete either dev or listdir option and retype the command.
- 471
- MESSAGE
'GROUP' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 471)
- CAUSE
The GROUP option was entered more than once.
- ACTION
Information only.
- 472
- MESSAGE
'GROUP' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'LOCAL' OPTION (S/R 472)
- CAUSE
Group and local options are not allowed on the same command line.
- ACTION
Delete either group or local option and retype the command.
- 473
- MESSAGE
EXPECTED '=groupname' AFTER 'GROUP' OPTION WHERE groupname IS THE NAME OF "GROUP" WHERE THE SPECIFIED SET OF FILES IS TO BE RESTORED.
SYNTAX 'GROUP=groupname' (S/R 473)- CAUSE
You typed the group parameter incorrectly.
- ACTION
Check the syntax and retype the command.
- 474
- MESSAGE
EXPECTED 'groupname' TO BE SPECIFIED FOR 'GROUP' OPTION. A groupname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH.
SYNTAX 'GROUP=groupname' (S/R 474)- CAUSE
You did not include the groupname for group option.
- ACTION
Check the syntax and retype the command.
- 475
- MESSAGE
'GROUP' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 475)
- CAUSE
Group and listdir options are not allowed on the same command line.
- ACTION
Delete either group or listdir option and retype the command.
- 481
- MESSAGE
'ACCOUNT' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 481)
- CAUSE
The ACCOUNT option was entered more than once.
- ACTION
Information only.
- 482
- MESSAGE
'ACCOUNT' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'LOCAL' & OPTION (S/R 482)
- CAUSE
Account and local options are not allowed on the same command line.
- ACTION
Delete either account or local option and retype the command.
- 483
- MESSAGE
EXPECTED '=accountname' AFTER 'ACCOUNT' OPTION WHERE accountname IS THE NAME OF "ACCOUNT" WHERE THE SPECIFIED SET OF FILES IS TO BE RESTORED.
SYNTAX 'ACC[OUN]T=accountname' (S/R 483)- CAUSE
You did not type the account parameter correctly.
- ACTION
Check the syntax and retype the command.
- 484
- MESSAGE
EXPECTED 'accountname' TO BE SPECIFIED FOR 'ACCOUNT' OPTION. A accountname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH.
SYNTAX 'ACC[OUN]T=accountname' (S/R 484)- CAUSE
You did not include the accountname for account option.
- ACTION
Check the syntax and retype the command.
- 485
- MESSAGE
'ACCOUNT' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 485)
- CAUSE
Account and listdir options are not allowed on the same command line.
- ACTION
Delete either account or listdir option and retype the command.
- 501
- MESSAGE
WARNING: 'CREATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 501)
- CAUSE
The CREATE option was entered more than once.
- ACTION
Information only.
- 502
- MESSAGE
'CREATE' OPTION DEFAULTING TO 'CREATE=ACCOUNT,GROUP,CREATOR' BASED ON YOUR CAPABILITIES. (S/R 502)
- CAUSE
Default parameters are used.
- ACTION
Information only.
- 503
- MESSAGE
'CREATE' OPTION DEFAULTING TO 'CREATE=GROUP,CREATOR' BASED ON YOUR CAPABILITIES. NOTE: ONLY GROUPS AND USERS IN YOUR ACCOUNT WILL BE CREATED. (S/R 503)
- CAUSE
Create only creating groups and users in your account.
- ACTION
Information only.
- 504
- MESSAGE
'CREATE' OPTION REQUIRES (SM) CAPABILITY FOR 'ACCOUNT' PARAMETER AND (SM) AND/OR (AM) CAPABILITY FOR 'GROUP' AND 'CREATOR' PARAMETERS. (S/R 504)
- CAUSE
You do not have system manager (SM) capability.
- ACTION
Log on to an account with SM or have your system manager perform the tasks.
- 505
- MESSAGE
'GROUP' PARAMETER OF THE 'CREATE' OPTION REQUIRES (SM) AND/OR (AM) CAPABILITY. NOTE: (AM) CAPABILITY WILL ONLY ALLOW YOU TO CREATE GROUPS IN YOUR HOME ACCOUNT (S/R 505)
- CAUSE
You do not have system manager (SM) capability or account manager (AM) capabilities for this account.
- ACTION
Log on to an account with system manager (SM) capability or have your system manager perform the tasks.
- 506
- MESSAGE
NOTE: WITH (AM) CAPABILITY 'GROUP' PARAMETER OF THE 'CREATE' OPTION WILL ONLY ALLOW YOU TO CREATE GROUPS IN YOUR HOME ACCOUNT. (S/R 506)
- CAUSE
You may only create groups in your home account.
- ACTION
Information only.
- 507
- MESSAGE
'USER' PARAMETER OF THE 'CREATE' OPTION REQUIRES (SM) AND/OR (AM) CAPABILITY. NOTE: (AM) CAPABILITY WILL ONLY ALLOW YOU TO CREATE USERS IN YOUR HOME ACCOUNT (S/R 507)
- CAUSE
You do not have system manager capability or account manager capability.
- ACTION
Log on to an account with SM or have your system manager perform the tasks.
- 508
- MESSAGE
'ACCOUNT' PARAMETER OF THE 'CREATE' OPTION REQUIRES (SM) CAPABILITY (S/R 508)
- CAUSE
Same as message content.
- ACTION
Include account parameter for the create option.
- 509
- MESSAGE
NOTE: WITH (AM) CAPABILITY 'USER' PARAMETER OF THE 'CREATE' OPTION WILL ONLY ALLOW YOU TO CREATE USER IN YOUR HOME ACCOUNT (S/R 509)
- CAUSE
You may only create users in your home account.
- ACTION
Information only.
- 510
- MESSAGE
UNKNOWN PARAMETER SPECIFIED FOR THE 'CREATE' OPTION. EXPECTED ONE OF 'ACCOUNT', 'GROUP', OR 'CREATOR'.
SYNTAX 'CREATE[=createparm[,createparm....]]' WHERE createparm IS ONE OF 'ACCOUNT', 'GROUP', OR 'CREATOR' (S/R 510)- CAUSE
You did not specify a valid create parameter.
- ACTION
Retype the command and include a valid create parameter.
- 511
- MESSAGE
EXPECTED createparm FOR THE 'CREATE' OPTION. EXPECTED ONE OF 'ACCOUNT', 'GROUP', OR 'CREATOR'.
SYNTAX 'CREATE[=createparm[,createparm....]]' WHERE createparm IS ONE OF 'ACCOUNT', 'GROUP', OR 'CREATOR'. (S/R 511)- CAUSE
You did not include the create parameter.
- ACTION
Retype the command and include a create parameter.
- 512
- MESSAGE
'CREATE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 512)
- CAUSE
Create and listdir options are not allowed on the same command line.
- ACTION
Delete either create or listdir option and retype the command.
- 513
- MESSAGE
'CREATE' OPTION DEFAULTING TO 'CREATE=PATH' BASED ON YOUR CAPABILITIES. NOTE: ONLY PATHS ALLOWED BY SECURITY RULES WILL BE CREATED (S/R 513)
- CAUSE
Since no suboptions were given to CREATE, the default suboption is PATH, based on the user's capabilities.
- ACTION
Information only.
- 521
- MESSAGE
'CREATOR' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 521)
- CAUSE
The CREATOR option was entered more than once.
- ACTION
Information only.
- 522
- MESSAGE
EXPECTED '=username' AFTER 'CREATOR' OPTION WHERE username IS THE NAME OF "USER" WHO EXISTS IN THE ACCOUNT WHERE THE SPECIFIED SET OF FILES IS TO BE RESTORED SUCH THAT THE SPECIFIED USER IS TO BE THE NEW "CREATOR" OF THE FILES.
SYNTAX 'CREATOR[=username]' WHERE 'CREATOR' WITH NO "username" SPECIFIED DEFAULTS TO THE ORIGNAL CREATOR OF THE FILE. (S/R 522)- CAUSE
You did not specify a valid creator parameter.
- ACTION
Check the syntax and retype the command.
- 523
- MESSAGE
EXPECTED 'username' TO BE SPECIFIED FOR 'CREATOR' OPTION. A username NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH.
SYNTAX 'CREATOR[=username]' WHERE 'CREATOR' WITH NO "username" SPECIFIED DEFAULTS TO THE ORIGNAL CREATOR OF THE FILE. (S/R 523)- CAUSE
You did not specify the username for the creator option.
- ACTION
Retype the command and include the username.
- 524
- MESSAGE
'CREATOR' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 524)
- CAUSE
Creator and listdir options are not allowed on the same command line.
- ACTION
Delete either creator or listdir option and retype the command.
- 525
- MESSAGE
! NOT RESTORED: FILE CREATOR REQUIRES (ND) CAPABILITY (S/R 525)
- CAUSE
You can not restore this file becuase you need to have non-sharable device capability.
- ACTION
As the system manager or operator to restore this file for you.
- 526
- MESSAGE
EXPECTED 'acctname' TO BE SPECIFIED FOR 'CREATOR' OPTION. AN acctname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH. SYNTAX 'CREATOR[=username[.acctname]]' WHERE 'CREATOR' WITH NO "username" AND "acctname" SPECIFIED DEFAULTS TO THE ORIGNAL CREATOR OF THE FILE (S/R 526)
- CAUSE
The acctname suboption was missing from the creator option.
- ACTION
Check the syntax of the creator option and retype the command.
- 527
- MESSAGE
EXPECTED '.' TO BE SPECIFIED AFTER username FOR 'CREATOR' OPTION.
SYNTAX 'CREATOR[=username[.acctname]]' WHERE 'CREATOR' WITH NO "username" AND "acctname" SPECIFIED DEFAULTS TO THE ORIGNAL CREATOR OF THE FILE (S/R 527)- CAUSE
The acctname part of the creator option was not specified correctly.
- ACTION
Check the syntax of the acctname part of creator and retype the command.
- 531
- MESSAGE
WARNING: 'LOCAL' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 531)
- CAUSE
The LOCAL option was entered more than once.
- ACTION
Information only.
- 532
- MESSAGE
'LOCAL' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'GROUP' OPTION (S/R 532)
- CAUSE
Local and group options are not allowed on the same command line.
- ACTION
Delete either local or group option and retype the command.
- 533
- MESSAGE
'LOCAL' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'ACCOUNT' OPTION (S/R 533)
- CAUSE
Local and account options are not allowed on the same command line.
- ACTION
Delete either local or account option and retype the command.
- 534
- MESSAGE
'LOCAL' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 534)
- CAUSE
Local and listdir options are not allowed on the same command line.
- ACTION
Delete either local or listdir option and retype the command.
- 541
- MESSAGE
WARNING: 'KEEP' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 541)
- CAUSE
The KEEP option was entered more than once.
- ACTION
Information only.
- 542
- MESSAGE
'KEEP' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'NOKEEP' OPTION. (S/R 542)
- CAUSE
Keep and nokeep options are not allowed on the same command line.
- ACTION
Delete either keep or nokeep option and retype the command.
- 543
- MESSAGE
'KEEP' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 543)
- CAUSE
Keep and listdir options are not allowed on the same command line.
- ACTION
Delete either keep or listdir option and retype the command.
- 551
- MESSAGE
WARNING: 'NOKEEP' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 551)
- CAUSE
The NOKEEP option was entered more than once.
- ACTION
Information only.
- 552
- MESSAGE
'NOKEEP' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'KEEP' OPTION. (S/R 552)
- CAUSE
Nokeep and keep options are not allowed on the same command line.
- ACTION
Delete either nokeep or keep option and retype the command.
- 553
- MESSAGE
'NOKEEP' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 553)
- CAUSE
Nokeep and listdir options are not allowed on the same command line.
- ACTION
Delete either nokeep or listdir option and retype the command.
- 561
- MESSAGE
WARNING: 'OLDDATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 561)
- CAUSE
The OLDDATE option was entered more than once.
- ACTION
Information only.
- 562
- MESSAGE
'OLDDATE' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'NEWDATE' OPTION. (S/R 562)
- CAUSE
Olddate and newdate options are not allowed on the same command line.
- ACTION
Delete either olddate or newdate option and retype the command.
- 563
- MESSAGE
'OLDDATE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 563)
- CAUSE
Olddate and listdir options are not allowed on the same command line.
- ACTION
Delete either olddate or listdir option and retype the command.
- 571
- MESSAGE
WARNING: 'NEWDATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 571)
- CAUSE
The NEWDATE option was entered more than once.
- ACTION
Information only.
- 572
- MESSAGE
'NEWDATE' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'OLDDATE' OPTION. (S/R 572)
- CAUSE
Newdate and olddate options are not allowed on the same command line. .
- ACTION
Delete either newdate or olddate option and retype the command.
- 573
- MESSAGE
'NEWDATE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 573)
- CAUSE
Newdate and listdir options are not allowed on the same command line. .
- ACTION
Delete either newdate or listdir option and retype the command.
- 581
- MESSAGE
'LISTDIR' OPTION CANNOT BE USED IN CONJUNCTION WITH ANY OTHER OPTION ASIDE FROM THE 'DIRECTORY' OPTION. (S/R 581)
- CAUSE
Same as the message content.
- ACTION
Information only.
- 591
- MESSAGE
WARNING: 'DATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 591)
- CAUSE
The DATE option was entered more than once.
- ACTION
Information only.
- 592
- MESSAGE
EXPECTED '<=accdate' OR '>=moddate' AFTER 'DATE' OPTION WHERE '<= PRIOR TO OR THE SAME AS THAT DATE WILL BE SELECTED FOR STORE, AND '>=moddate' SPECIFIES A DATE SUCH THAT FILES MODIFIED AFTER OR ON THAT DATE WILL BE SELECTED FOR STORE.
SYNTAX 'DATE>=moddate' OR 'DATE<=accdate'. (S/R 592)- CAUSE
You did not type the date parameter correctly.
- ACTION
Check the syntax and retype the command.
- 593
- MESSAGE
THE MONTH PORTION OF SPECIFIED DATE MUST BE BETWEEN 1 AND 12.
DATE SYNTAX 'mm/dd/yy[yy]' (S/R 593)- CAUSE
You did not specify a valid number for the month parameter.
- ACTION
Check the syntax and enter a valid number.
- 594
- MESSAGE
A SLASH "/" WAS EXPECTED TO SEPARATE THE MONTH (mm) FROM THE DAY (dd) IN THE SPECIFIED DATE.
SYNTAX 'mm/dd/yy[yy]' (S/R 594)- CAUSE
You did not include a slash.
- ACTION
Check the syntax and retype the command.
- 595
- MESSAGE
DAY PORTION OF DATE IS INVALID. IT MUST BE BETWEEN 1 AND 28, 29, 30, OR 31 BASED ON THE SPECIFIED DATE.
SYNTAX 'mm/dd/yy[yy]' (S/R 595)- CAUSE
You did not include a valid number for day parameter.
- ACTION
Check the syntax and enter a valid number for day parameter.
- 596
- MESSAGE
A SLASH "/" WAS EXPECTED TO SEPARATE THE MONTH (dd) FROM THE YEAR (yy[yy]) IN THE SPECIFIED DATE.
SYNTAX 'mm/dd/yy[yy]' (S/R 596)- CAUSE
You did not include a slash.
- ACTION
Check the syntax and retype the command.
- 597
- MESSAGE
YEAR PORTION OF DATE IS INVALID. IT MUST BE GREATER THAN 1970 (70) AND LESS THAN 2127 OR 99 FOR 1999.
DATE SYNTAX 'mm/dd/yy[yy]' (S/R 597)- CAUSE
You did not include a valid number for the year parameter.
- ACTION
Check the syntax and enter a valid number for the year parameter.
- 598
- MESSAGE
EXPECTED MONTH (mm) PORTION OF DATE. SPECIFIED MONTH VALUE MUST BE BETWEEN 1 AND 12.
DATE SYNTAX 'mm/dd/yy[yy]' (S/R 598)- CAUSE
You did not include month parameter for date option.
- ACTION
Check the syntax and retype the command.
- 599
- MESSAGE
EXPECTED DAY (dd) PORTION OF DATE. SPECIFIED DAY VALUE MUST BE BE BETWEEN 1 AND 28, 29, 30, OR 31 BASED ON THE SPECIFIED MONTH.
DATE SYNTAX 'mm/dd/yy[yy]' (S/R 599)- CAUSE
You did not include day parameter for date option.
- ACTION
Check the syntax and retype the command.
Store/Restore Messages 600 - 706
- 600
- MESSAGE
EXPECTED YEAR (yy[yy]) PORTION OF DATE. SPECIFIED YEAR VALUE MUST BE GREATER THAN 1970 (70) AND LESS THAN 2127 OR 99 FOR 1999.
DATE SYNTAX 'mm/dd/yy[yy]' (S/R 600)- CAUSE
You did not include year parameter for date option.
- ACTION
Check the syntax and retype the command.
- 601
- MESSAGE
'DATE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 601)
- CAUSE
Date and listdir options are not allowed on the same command line.
- ACTION
Delete either date or listdir option and retype the command.
- 611
- MESSAGE
WARNING: 'PURGE' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 611)
- CAUSE
The PURGE option was entered more than once.
- ACTION
Information only.
- 631
- MESSAGE
WARNING: 'ONERROR' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 631)
- CAUSE
The ONERROR option was entered more than once.
- ACTION
Information only.
- 632
- MESSAGE
EXPECTED '=error-parm' AFTER 'ONERROR' OPTION WHERE error-parm IS EITHER 'QUIT' OR 'REDO'.
SYNTAX 'ONERR[OR]={QUIT}, OR {REDO} (S/R 632)- CAUSE
You did not type the onerror parameter correctly.
- ACTION
Check the syntax and retype the command.
- 633
- MESSAGE
UNKNOWN PARAMETER SPECIFIED FOR THE 'ONERROR' OPTION. EXPECTED EITHER 'QUIT' OR 'REDO'.
SYNTAX 'ONERR[OR]={QUIT}, OR {REDO} (S/R 633)- CAUSE
You typed a invalid onerror parameter.
- ACTION
Retype the command and include a valid onerror parameter.
- 641
- MESSAGE
EXPECTED '=(read cnt),(queued writes),(outstanding writes)' AFTER 'TUNE' OPTION.
SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 641)- CAUSE
You did not type the tune parameter correctly.
- ACTION
Check the syntax and retype the command.
- 642
- MESSAGE
EXPECTED '(read cnt),(queued writes),(outstanding writes)' AFTER 'TUNE=' IN 'TUNE' OPTION.
SYNTAX 'TUNE=(read cnt), (queued writes), (outstanding writes)' (S/R 642)- CAUSE
You did not specify a valid tune parameter.
- ACTION
Check the syntax and retype the command.
- 643
- MESSAGE
EXPECTED (read cnt) OF 'TUNE' OPTION TO BE BETWEEN 1 and 12.
SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 642)- CAUSE
The read cnt parameter is not in the correct range.
- ACTION
Retype the command and include a valid number.
- 644
- MESSAGE
EXPECTED '(queued writes),(outstanding writes)' AFTER 'TUNE=(read cnt)' IN 'TUNE' OPTION.
SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 644)- CAUSE
You did not type the tune parameter correctly.
- ACTION
Check the syntax and retype the command.
- 645
- MESSAGE
EXPECTED (queued writes) OF 'TUNE' OPTION TO BE BETWEEN 1 and 16.
SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 645)- CAUSE
The queued writes parameter is not in the range.
- ACTION
Retype the command and include a valid number.
- 646
- MESSAGE
EXPECTED ',' TO SEPARATE PARAMETERS FOR THE 'TUNE' OPTION.
SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 646)- CAUSE
You did not include a comma.
- ACTION
Check the syntax and retype the command.
- 647
- MESSAGE
EXPECTED '(outstanding writes)' AFTER 'TUNE=(read cnt), (queued writes)' IN 'TUNE' OPTION.
SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 647)- CAUSE
You did not type the tune parameter correctly.
- ACTION
Check the syntax and retype the command.
- 648
- MESSAGE
EXPECTED (outstanding writes) OF 'TUNE' OPTION TO BE BETWEEN 1 and 4.
SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 648)- CAUSE
The outstanding writes parameter is not in the range.
- ACTION
Retype the command and include a valid number.
- 670
- MESSAGE
WARNING: 'LISTDIR' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 670)
- CAUSE
The LISTDIR option was entered more than once.
- ACTION
Information only.
- 675
- MESSAGE
'MAXTAPEBUF' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 675)
- CAUSE
The MAXTAPEBUF option was entered more than once.
- ACTION
Information only.
- 676
- MESSAGE
'MAXTAPEBUF' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 676)
- CAUSE
Maxtapebuf and transport options are not allowed on the same command line.
- ACTION
Delete either maxtapebuf or transport option and retype the command.
- 681
- MESSAGE
'INTER' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 681)
- CAUSE
Inter and transport options are not allowed on the same command line.
- ACTION
Delete either inter or transport option and retype the command.
- 682
- MESSAGE
WARNING: 'INTER' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 682)
- CAUSE
The INTER option was entered more than once.
- ACTION
Information only.
- 691
- MESSAGE
'COMPRESS' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 691)
- CAUSE
COMPRESS and TRANSPORT options are not allowed on the same command line.
- ACTION
CMSTORE and V/E cannot handle COMPRESS. Delete either COMPRESS or TRANSPORT option and retype the command.
- 692
- MESSAGE
'COMPRESS' OPTION REDUNDANTLY SPECIFIED (S/R 692)
- CAUSE
COMPRESS was entered twice on the same command line.
- ACTION
Delete one of the COMPRESS options and retype the command.
- 693
- MESSAGE
EXPECTED '=compressionparm[,compressionparm..]' AFTER 'COMPRESS' OPTION WHERE compressionparm IS ONE OF 'HIGH' OR 'LOW'. SYNTAX 'COMPRESS=compressionparm[,compressionparm....]' (S/R 693)
- CAUSE
You left out the '=' sign after the COMPRESS option.
- ACTION
Retype the command and include the '=' sign after the COMPRESS option.
- 694
- MESSAGE
EXPECTED 'compressionparm[,compressionparm..]' AFTER 'COMPRESS=' OPTION WHERE compressionparm IS ONE OF 'HIGH' OR 'LOW'. SYNTAX 'COMPRESS=compressionparm[,compressionparm....]' (S/R 694)
- CAUSE
You typed an invalid parameter for COMPRESS option.
- ACTION
Retype the command and include a valid parameter for COMPRESS option.
- 695
- MESSAGE
'HIGH' AND 'LOW' PARAMETERS OF THE 'COMPRESS' OPTION CANNOT BE SPECIFIED TOGETHER (S/R 695)
- CAUSE
HIGH and LOW parameters are not allowed on the same command line.
- ACTION
Delete either LOW or HIGH parameter and retype the command.
- 696
- MESSAGE
'LOW' PARAMETER OF 'COMPRESS' OPTION CANNOT BE REDUNDANTLY SPECIFIED (S/R 696)
- CAUSE
The parameter LOW was specified twice.
- ACTION
Delete one of the LOW parameters and retype the command.
- 697
- MESSAGE
'HIGH' PARAMETER OF 'COMPRESS' OPTION CANNOT BE REDUNDANTLY SPECIFIED (S/R 697)
- CAUSE
The parameter HIGH was specified twice.
- ACTION
Delete one of the HIGH parameters and retype the command.
- 699
- MESSAGE
COMPRESSION OPTION IS NOT AVAILABLE ON YOUR VERSION OF STORE (S/R 699)
- CAUSE
This option is available only if TurboSTORE XL is installed on you system.
- ACTION
TurboSTORE XL is not part of the fundamental operating system but may be purchased separately.
- 701
- MESSAGE
'SPLITVS' OPTION CANNOT BE USED WITH THE 'TRANSPORT' TO MPEv (S/R 701)
- CAUSE
SPLITVS and TRANSPORT options are not allowed on the same command line.
- ACTION
Delete SPLITVS or TRANSPORT option and retype the command.
- 702
- MESSAGE
WARNING: 'SPLITVS' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 702)
- CAUSE
The SPLITVS option was entered more than once.
- ACTION
Information only.
- 703
- MESSAGE
EXPECTED '=volumesetname[,volumesetname...]' AFTER 'SPLITVS' OPTION SYNTAX 'SPLITVS=volumesetname[,volumesetname...]' (S/R 703)
- CAUSE
The '=' sign was left out after the SPLITVS option.
- ACTION
Retype the command and include the '=' sign after the SPLITVS opti on.
- 704
- MESSAGE
INVALID VOLUMESET NAME SPECIFIED FOR 'SPLITVS' OPTION. VOLUMESET NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", "_" AND "." SYNTAX 'SPLITVS=volumesetname [,volumesetname...]' (S/R 704)
- CAUSE
The volumeset name specified for SPLITVS is invalid.
- ACTION
Retype the command and include a valid volumeset name.
- 705
- MESSAGE
VOLUMESET NAME SPECIFIED FOR 'SPLITVS' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 32 CHARACTERS.
SYNTAX 'SPLITVS=volumesetname[,volumesetname...]' (S/R 705)- CAUSE
The volumeset name specified for SPLITVS option includes more than 32 characters.
- ACTION
Retype the command and make sure the volumeset name includes 32 characters or less.
- 706
- MESSAGE
EXPECTED 'volumesetname[,volumesetname...]' AFTER 'SPLITVS=' WHERE volumesetname IS THE NAME OF A VOLUME SET THAT IS CURRENTLY MOUNTED IN A SPLIT STATE ON YOUR SYSTEM.
SYNTAX 'SPLITVS=volumesetname[,volumesetname...]' (S/R 706)- CAUSE
You have not entered a mounted volumesetname for SPLITVS option.
- ACTION
Retype the command and include a mounted volumesetname with your command.
|
Chapter 9 "Nonclass" Errors |
Chapter 11 Store/Restore (Native Mode) and TurboSTORE/iX II |