Chapter 2 Native Mode Spooler
(Subsystem 236)
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II | |
| E0300 Volume I | |
| E0300 Volume II ♥ | |
| E0300 Volume III | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
Spooler 0 - 7999
- 0
- MESSAGE
END OF FILE (FSERR 0)
- 1
- MESSAGE
Error while purging a terminating spooler process' port during cleanup.
- 2
- MESSAGE
The current state and the expected state of the spooling process do not match.
- 3
- MESSAGE
A warning occured during the cleanup of a spooling process.
- 50
- MESSAGE
A warning occured while getting information about a device.
- 51
- MESSAGE
An error occured during spooling of initially spooled devices.
- 100
- MESSAGE
Spooling of initially spooled devices is complete.
- 101
- MESSAGE
Set-up of Spooling Subsystem is complete.
- 501
- MESSAGE
An unexpected escape from an external routine was encountered.
- 503
- MESSAGE
Failed to lock the Spooler Process Information Table.
- 504
- MESSAGE
Failed to unlock the Spooler Process Information Table.
- 505
- MESSAGE
Failed attempt to retrieve information from a SPIT entry.
- 506
- MESSAGE
Failed attempt to update the SPIT entry of a spooler process.
- 507
- MESSAGE
Failed to delete SPIT entry during cleanup of terminating spooler process.
- 511
- MESSAGE
Failed attempt to use HPERRMSG routines to log an error.
- 512
- MESSAGE
Failed attempt to use GENMSG routine to display a spooler msg.
- 550
- MESSAGE
Failed to create the HPSPOOL account in the system directory.
- 551
- MESSAGE
Failed to create the OUT.HPSPOOL group in the system directory.
- 552
- MESSAGE
Failed to create the IN.HPSPOOL group in the system directory.
- 553
- MESSAGE
An unexpected escape was encountered during startup of the spooling subsystem.
- 554
- MESSAGE
Unable to delimit a device name while initially spooling devices.
- 555
- MESSAGE
Unable to convert ldev to device name while initially spooling devices.
- 556
- MESSAGE
Unable to get information about a device while initially spooling devices.
- 557
- MESSAGE
Critical error during setup of spooling system. Cannot use spooling subsystem until the system is restarted.
- 600
- MESSAGE
Error encountered while sending a system shutdown message to the Spooler Monitor's port.
- 2001
- MESSAGE
A warning occured while starting the Spooler Monitor process.
- 2006
- MESSAGE
The Spooler Monitor received a warning while starting a spooler process.
- 2007
- MESSAGE
The Spooler Monitor received an error while purging a port. This is a non-critical error.
- 2008
- MESSAGE
An escape to the RECOV block occurred after the spooler process was activated. This is a non-critical warn.
- 2051
- MESSAGE
The Spooling system has been shutdown.
- 2501
- MESSAGE
The Spooler Monitor received an unexpected escape during normal execution.
- 2502
- MESSAGE
The Spooler Monitor could not be created.
- 2504
- MESSAGE
Unable to create a spooler process for device \.
- 2505
- MESSAGE
Unable to create a port for the spooler process of device \.
- 2506
- MESSAGE
Unable to give port ownership to spooler process of device \.
- 2507
- MESSAGE
Unable to activate the spooler process created for device \.
- 2508
- MESSAGE
An error occurred while the Spooler Monitor was receiving a message on its port.
- 2509
- MESSAGE
The Spooler Monitor received an invalid message on its port.
- 2510
- MESSAGE
The Spooler Monitor was asked to create an invalid type of spooler process.
- 2511
- MESSAGE
The Spooler Monitor was unable to lock the SPIT table.
- 2512
- MESSAGE
The Spooler Monitor was unable to unlock the SPIT table.
- 2513
- MESSAGE
The Spooler Monitor received an error while retrieving information from the SPIT table.
- 2514
- MESSAGE
The Spooler Monitor received an error while updating an entry in the SPIT table.
- 2515
- MESSAGE
The Spooler Monitor received an error while deleting an entry from the SPIT table.
- 2520
- MESSAGE
The Spooler Monitor received an error during initialization.
- 2521
- MESSAGE
The Spooler Monitor received an error during shutdown of the spooling subsystem.
- 2522
- MESSAGE
The Spooler Monitor returned from shutdown, an event that should never occur.
- 2526
- MESSAGE
You cannot run the Spooler Monitor (SPOOLMOM) as a user program.
- 2523
- MESSAGE
The Spooler Monitor has entered code that should never be executed in normal situations.
- 3501
- MESSAGE
Unexpected error (escape) returned from other subsystems.
- 3502
- MESSAGE
Cannot find the SPIT KSO number.
- 3503
- MESSAGE
Cannot lock the SPIT.
- 3504
- MESSAGE
Cannot unlock the SPIT.
- 3505
- MESSAGE
Cannot allocate new entry in the SPIT.
- 3506
- MESSAGE
Cannot find the entry with the given device name in SPIT.
- 3507
- MESSAGE
Entry with the given device name already exists in SPIT.
- 3508
- MESSAGE
The given keyword is missing from the SPIT get/put interface.
- 3509
- MESSAGE
Keyvalue is not passed to the SPIT get/put interface.
- 3510
- MESSAGE
The given keyword is not a valid keyword for the SPIT get/put interface.
- 3511
- MESSAGE
SPIT get/put interface allows only 20 key pairs, the given key index somehow is out of range.
- 3512
- MESSAGE
Cannot create object for building SPIT.
- 3513
- MESSAGE
Cannot create SPIT because of symbol table management error.
- 3514
- MESSAGE
Cannot delete the given entry from SPIT.
- 3515
- MESSAGE
The kind of process passed to SPIT interface is illegal, it must be either input or output.
- 3516
- MESSAGE
Cannot send an active spoolfile message due to some error condition.
- 3601
- MESSAGE
Cannot start a spooler process for an initially spooled device.
- 3602
- MESSAGE
Cannot create port for the spooler MOM process.
- 3603
- MESSAGE
Cannot initiate the spooler MOM process.
- 3604
- MESSAGE
Cannot initiate the spooling subsystem.
- 3605
- MESSAGE
Cannot create the spoolfile directory.
- 3606
- MESSAGE
Cannot create the HPSPOOL accounting structure.
- 4513
- MESSAGE
Spooler internal error occurred, cannot update device information.
- 4593
- MESSAGE
Invalid 'DISP' specified, "SPSAVE" OR "PURGE".
- 4627
- MESSAGE
Device "\" must be a printer.
- 4628
- MESSAGE
Global queues or queues for device "\" must be open.
- 4629
- MESSAGE
Global queues or queues for a device in class "\" must be open.
- 4630
- MESSAGE
Device "\" must be spoolable for output.
- 4631
- MESSAGE
A device in class "\" must be spoolable for output.
- 4632
- MESSAGE
Device "\" must be spooled for output.
- 4633
- MESSAGE
A device in class "\" must be spooled for output.
- 4658
- MESSAGE
SPSAVED spoolfile "!" cannot be deferred.
- 4793
- MESSAGE
A spoolid wildcard of the form @, I@, OR O@ was expected.
- 4900
- MESSAGE
! warnings occurred.
- 5000
- MESSAGE
No spoolfiles available for this spooler to process.
- 5001
- MESSAGE
Attempted to remove an output spoolfile from a queue when it's not on one.
- 5003
- MESSAGE
During recovery of a file still being CREATED when the system was interrupted, could not recover all data out to the file's limit.
- 5004
- MESSAGE
The creator of the spoolfile did not have access to the target device during a "RAW CREATE". The spoolfile was created, but it was put in the DEFER state.
- 5005
- MESSAGE
The system has finished rebuilding the output spoolfile directory.
- CAUSE
At boot time, the system is allowed to come completely up while the output spool file directory continues to be rebuilt. This message indicates that that process has finished.
- ACTION
None. Informational message.
- 5250
- MESSAGE
Attempted to retrieve an invalid/non-existent spoolfile attribute.
- 5251
- MESSAGE
Attempted to SET an invalid/non-existent spoolfile attribute.
- 5252
- MESSAGE
Internal error sequentially reading spoolfile directory entries. Possible spoolfile directory corruption.
- 5253
- MESSAGE
Cannot specify both spoolfile id and UFID as file selectors.
- 5254
- MESSAGE
Must specify either a spoolfile id or a UFID as a file selector.
- 5255
- MESSAGE
The GETINFO intrinsic reported an error to the process rebuilding the output spoolfile directory.
- CAUSE
Progen passes information to the process that rebuilds the output spool file directory. That process retrieves it with the GETINFO intrinsic, but the intrinsic call failed.
- ACTION
To recover existing spool files, STORE (;PURGE) them to tape and RESTORE them. Or SPOOLF @.OUT.HPSPOOL;PRINT them (then delete the original files). Files which were incomplete when the system was taken down may not print correctly.
- 5256
- MESSAGE
Cannot find a spoolfile directory entry which is expected to exist.
- 5257
- MESSAGE
Must specify either the input or output spoolfile directory.
- 5258
- MESSAGE
Cannot specify both the input and output spoolfile directories.
- 5259
- MESSAGE
Cannot lock the GUFD spoolfile management resource while the SPFDIR resource is locked, may cause a deadlock.
- 5260
- MESSAGE
Failure occurred re-inserting an SPFDIR entry whose search key(s) have been altered. May indicate SPFDIR/disc space shortage or corruption.
- 5261
- MESSAGE
Could not add an SPFDIR entry, the directory is full.
- 5262
- MESSAGE
Failure attempting to gain exclusive access to a spoolfile's label and label extensions.
- 5265
- MESSAGE
Could not find a spoolfile directory entry for the given UFID and directory (input or output SPFDIR).
- 5266
- MESSAGE
Failure attempting to lock either the input or the output spoolfile directory.
- 5267
- MESSAGE
Failure attempting to unlock either the input or the output spoolfile directory.
- 5268
- MESSAGE
Unable to obtain the starting address of a spoolfile directory.
- 5271
- MESSAGE
The spoolfile management architected interface routines encountered an unexpected state.
- 5274
- MESSAGE
Could not gain exclusive access to a spoolfile's label and label extensions.
- 5275
- MESSAGE
Could not release a spoolfile's label from exclusive access.
- 5276
- MESSAGE
JOB/SESSION tried to delete a STDIN spoolfile not in the READY state.
- 5277
- MESSAGE
Deletion of a spoolfile directory entry, specified by its search key, failed.
- 5278
- MESSAGE
Tried to delete a STDIN spoolfile using :SPOOLF ;DELETE. Such files can only be deleted with the ABORTJOB command on the file's associated job.
- 5279
- MESSAGE
Duplicate SPFDIR entry, its primary and secondary key values match those of an existing SPFDIR entry.
- 5280
- MESSAGE
No spoolfile exists with the given name or UFID.
- 5281
- MESSAGE
FCLOSE of spoolfile failed.
- 5282
- MESSAGE
Internal error mapping from spoolfile directory entry handle to its address.
- 5283
- MESSAGE
Unmatched ITEM NUMBER or ITEM in call to Spoolfile Management architected interface.
- 5284
- MESSAGE
Spoolfile Management encountered an unexpected escape or trap.
- 5285
- MESSAGE
Could not create a virtual object to hold the input spoolfile directory.
- 5286
- MESSAGE
Could not create a virtual object to hold the output spoolfile directory.
- 5287
- MESSAGE
Could not create input spoolfile directory symbol table.
- 5288
- MESSAGE
Could not create output spoolfile directory symbol table.
- 5289
- MESSAGE
Could not create a virtual object to hold output spoolfile queue entries.
- 5290
- MESSAGE
Could not create output spoolfile queue head symbol table.
- 5291
- MESSAGE
Could not re-open a spoolfile already opened by the current process.
- 5292
- MESSAGE
Could not gain access to the label of a file already opened by the current process.
- 5293
- MESSAGE
FCLOSE of a spoolfile failed.
- 5294
- MESSAGE
Read or write of a spoolfile's label extension failed.
- 5295
- MESSAGE
Spoolfile does not exist on any of the volumes currently mounted.
- 5296
- MESSAGE
Low-level open of spoolfile failed due to file descriptor allocation limitations.
- 5297
- MESSAGE
System error performing low-level open of spoolfile.
- 5298
- MESSAGE
The spoolfile was still in the CREATE state when the system was interrupted. It could not be recovered, and has been deleted.
- 5299
- MESSAGE
Infinite loop corruption detected in output spoolfile directory. Reboot your system to rebuild the directory. If the problem recurs, CONTACT YOUR SE.
- 5300
- MESSAGE
Unknown error performing low-level open of spoolfile.
- 5302
- MESSAGE
Output spoolfile has invalid state.
- 5303
- MESSAGE
Attempt to add a new output spoolfile queue head entry failed due to existence of a queue head for the same output device or class.
- 5304
- MESSAGE
Output spoolfile queue head table overflow. CONTACT YOUR SE.
- 5305
- MESSAGE
Output spoolfile queue corruption detected. Invalid link to a queue's first entry. CONTACT YOUR SE.
- 5306
- MESSAGE
Output spoolfile queue corruption detected. Invalid forward link. CONTACT YOUR SE.
- 5307
- MESSAGE
Output spoolfile queue corruption detected. Invalid backward link. CONTACT YOUR SE.
- 5309
- MESSAGE
Unexpected escape encountered inserting an output spoolfile into a spoolfile queue.
- 5310
- MESSAGE
Could not find the device or class queue head entry matching the target device or class of an output spoolfile.
- 5312
- MESSAGE
Could not remove a spoolfile from the spooling queues.
- 5313
- MESSAGE
Could not retrieve the address of a workarea created for spooling subsystem command execution.
- 5315
- MESSAGE
Could not create a spooling command/AIF work area.
- 5316
- MESSAGE
Could not expand a spooling command/AIF work area.
- 5317
- MESSAGE
Could not deallocate a spooling command/AIF work area.
- 5318
- MESSAGE
Directory error while preparing to retrieve file system directory information for a set of spoolfiles.
- 5319
- MESSAGE
Directory error while retrieving file system directory information for a set of spoolfiles.
- 5320
- MESSAGE
Unknown/invalid spooler process type.
- 5321
- MESSAGE
Encountered transaction management error while updating creator of an output spoolfile in its label and label extension.
- 5322
- MESSAGE
Encountered error writing changes to an output spoolfile's file label extension when changing its creator.
- 5323
- MESSAGE
When changing creator of an output spoolfile in its label and label extension, the changes to these structures were aborted because a user transaction under which these system transactions occurred was aborted.
- 5340
- MESSAGE
SPOOLF ;PRINT encountered an error reading source file.
- 5341
- MESSAGE
SPOOLF ;PRINT encountered an error writing to target file.
- 5342
- MESSAGE
You cannot SPOOLF ;PRINT a Private output spoolfile.
- 5343
- MESSAGE
You cannot SPOOLF ;SPSAVE a Private output spoolfile.
- 5344
- MESSAGE
You cannot SPOOLF ;DEFER a spoolfile in the PROBLEM state unless you also ALTER it to a valid target device/class.
- 5345
- MESSAGE
You cannot SPOOLF ;DEFER an output spoolfile which has already been printed and has moved to the 'SPSAVE' state.
- 5346
- MESSAGE
You cannot alter the output priority of a spoolfile in the SPSAVE state.
- 5347
- MESSAGE
You cannot alter the number of copies of a spoolfile which is either Private or in the SPSAVE state.
- 5348
- MESSAGE
You cannot alter the target device/class of a spoolfile in the SPSAVE state.
- 5349
- MESSAGE
SPOOLF ;ALTER or SPOOLF ;DELETE of more than one spoolfile is disabled until the output spoolfile directory has been rebuilt following a system startup.
- CAUSE
You entered SPOOLF [O]@; ALTER or DELETE while the output spoolfile directory was still being rebuilt. This is not allowed because the command could miss some files which had not yet been inserted into the directory.
- ACTION
This situation only occurs for a few minutes following system startups. Try your command again a few minutes later.
- 5350
- MESSAGE
The specified or defaulted target device/class does not exist, is not output spoolable, or does not have its spooling queues open.
- 5351
- MESSAGE
Unable to obtain file information, the FFILEINFO intrinsic failed.
- 5352
- MESSAGE
The specified file is not a spoolfile.
- 5353
- MESSAGE
You tried to SPOOLF ;PRINT an empty file.
- 5354
- MESSAGE
SPOOLF ;PRINT aborted by BREAK.
- 5355
- MESSAGE
Could not change the STDLIST device in JOB/SESSION tables.
- 5356
- MESSAGE
File does not exist or could not be created.
- 5357
- MESSAGE
SPOOLF ;PRINT -- valid range of copies is 1 to 65535.
- 5358
- MESSAGE
SPOOLF ;PRINT -- valid range of priorities is 0 to 14.
- 5359
- MESSAGE
Cannot open the file for exclusive access because it is already open.
- 5360
- MESSAGE
The specified lockword does not match the lockword on the file.
- 5361
- MESSAGE
You cannot UNDEFER a spoolfile in the PROBLM state.
- 5362
- MESSAGE
You cannot UNDEFER a spoolfile in the SPSAVE state.
- 5367
- MESSAGE
You cannot alter the attributes of an input spoolfile.
- 5368
- MESSAGE
You cannot delete an ACTIVE ":DATA" input spoolfile, that is, one currently being submitted via the STREAM command.
- 5369
- MESSAGE
You cannot delete an output spoolfile which is in the CREATE state.
- 5370
- MESSAGE
You cannot delete an input spoolfile which is in the OPEN state.
- 5373
- MESSAGE
Only output spoolfiles can be SPOOLF ;PRINT'ed.
- 5374
- MESSAGE
You cannot SPOOLF :PRINT an input spoolfile.
- 5375
- MESSAGE
The source file for a SPOOLF :PRINT has no target device or class to use as a default, therefore you must specify one with the command.
- 5376
- MESSAGE
The defaulted target device (taken from the source spoolfile of a SPOOLF :PRINT command) is not a valid output spooled device.
- 5377
- MESSAGE
Could not open the source file for a SPOOLF :PRINT command.
- 5378
- MESSAGE
Could not open the target file for a SPOOLF :PRINT command.
- 5379
- MESSAGE
The first character of a file lockword must be a letter.
- 5380
- MESSAGE
Too many characters were specified for the file lockword.
- 5381
- MESSAGE
The file lockword contains a non-alphanumeric character.
- 5382
- MESSAGE
Altering the target device of a Private spoolfile requires SM capability.
- 5383
- MESSAGE
Could not change the target device of an open STDLIST.
- 5384
- MESSAGE
Error encountered checking the target device
- 5385
- MESSAGE
Creator of spoolfile does not have access to the target device.
- 5386
- MESSAGE
If there is not an ACD on the target device, the accessor must have ND (non-sharable device) capability.
- 5387
- MESSAGE
An internal call to JSINFO failed.
- 5388
- MESSAGE
The creator of the spoolfile does not have access to the target device on a SPOOLF;DEV= or SPOOLF;UNDEFER. This error is used when a "Spoolid" insert is desired at the SP_AI level.
- 5389
- MESSAGE
The user does not have access to the device specified in the label extension of the spoolfile. This error is used when a "file name" insert is desired at the SP_AI level.
- 5390
- MESSAGE
The device specified in the label extension of the spoolfile does not have an ACD and the user does not have ND capability. This error is used when a "file name" insert is desired at the SP_AI level.
- 7500
- MESSAGE
An invalid DEV keyvalue was specified in the selection equation.
- 7501
- MESSAGE
Only = and <> are allowed as relational operators for the DEV selection equation keyword.
- 7502
- MESSAGE
An invalid PAGES keyvalue was specified in the selection equation.
- 7503
- MESSAGE
The COPIES keyvalue must be in the range of 1 to 65,535.
- 7504
- MESSAGE
The PRI keyvalue must be in the range of 0 to 14.
- 7505
- MESSAGE
An invalid FILEDES keyvalue was specified in the selection equation.
- 7506
- MESSAGE
Only '=' and <> are allowed as relational operators for the FILEDES selection equation keyword.
- 7507
- MESSAGE
Only = and <> are allowed as relational operators for the JOBNUM selectioni equation keyword.
- 7508
- MESSAGE
An invalid DATE keyvalue was specified in the selection equation.
- 7509
- MESSAGE
In the DATE keyvalue of the selection equation, the month must be in the range of 1 to 12.
- 7510
- MESSAGE
An invalid year was specified in the DATE keyvalue of the selection equation.
- 7511
- MESSAGE
An invalid JOBNUM keyvalue was specified in the selection equation.
- 7512
- MESSAGE
An invalid JOBNAME keyvalue was specified in the selection equation.
- 7513
- MESSAGE
An invalid FORMID keyvalue was specified in the selection equation.
- 7514
- MESSAGE
You must specify an account to use this command.
- 7515
- MESSAGE
A valid user name consists of a letter followed by alphanumeric characters.
- 7516
- MESSAGE
A valid account name consists of a letter followed by alphanumeric characters.
- 7517
- MESSAGE
The user name must contain eight or less characters.
- 7518
- MESSAGE
The account name must contain eight or less characters.
- 7519
- MESSAGE
The RECORDS keyvalue must be a positive integer.
- 7520
- MESSAGE
Only = and <> are allowed as relational operators for the OWNER selection equation keyword.
- 7521
- MESSAGE
Internal error while evaluating selection equation, there was no result to return. If this error persists, contact your SE.
- 7522
- MESSAGE
The DEV keyvalue must contain eight or less characters.
- 7524
- MESSAGE
Valid STATE keyvalues are READY, ACTIVE, OPEN, CREATE, PRINT, PROBLM, DELPND, SPSAVE, DEFER.
- 7525
- MESSAGE
Only = and <> are allowed as relational operators for the STATE selection equation keyword.
- 7526
- MESSAGE
The SPOOLID keyvalue must contain seven or fewer digits, not including the optional #0 or #1.
- 7527
- MESSAGE
The FILEDES keyvalue is too long.
- 7528
- MESSAGE
The JOBNUM keyvalue must be in the range of 1 to 16383.
- 7529
- MESSAGE
The JOBNAME keyvalue must contain eight or less characters.
- 7530
- MESSAGE
The FORMID keyvalue must contain eight or less characters.
- 7531
- MESSAGE
Only = and <> are allowed as relational operators for the JOBNAME selection equation keyword.
- 7532
- MESSAGE
Only = and <> are allowed as relational operators for the FORMID selection equation keyword.
- 7533
- MESSAGE
The SPOOLID keyvalue must be in the range of 1 to 9999999.
- 7534
- MESSAGE
The SPOOLID keyvalue must be numeric.
- 7535
- MESSAGE
Only = and <> are allowed as relational operators for the SPOOLID selection equation keyword.
- 7536
- MESSAGE
The only valid DISP keyvalues are SPSAVE and PURGE.
- 7537
- MESSAGE
Only = and <> are allowed as relational operators for the DISP selection equation keyword.
- 7538
- MESSAGE
If the "." is specified in user.acct, acct must also be specified.
- 7539
- MESSAGE
An internal error occurred while validating selection equation semantics. If the error persists, contact your SE.
- 7540
- MESSAGE
Expected either an 'I' or 'O' after the "#".
- 7541
- MESSAGE
In the DATE keyvalue of the selection equation, the day of the month must be in the range of 1 to maximum date in month.
- 7542
- MESSAGE
The only valid JOBABORT keyvalues are TRUE and FALSE.
- 7543
- MESSAGE
Only = and <> are allowed as relational operators for the JOBABORT selection equation keyword.
Spooler 8000 - 9499
- 8000
- MESSAGE
A stop or shut spooler message was received by the input spooling process.
- 8001
- MESSAGE
A BREAK or cntl-Y key was entered by the user during the STREAM command.
- 8002
- MESSAGE
An EOF was received while reading from the source file being input spooled.
- 8003
- MESSAGE
A record exceeding the maximum record size of 279 characters was read from the source file being input spooled.
- 8004
- MESSAGE
The expanded :JOB or :DATA record exceeded the maximum record size of 279 characters.
- 8005
- MESSAGE
The continuation rec for the job/data cmnd did not begin with the pseudo colon.
- 8006
- MESSAGE
The :JOB or :DATA record failed to logon successfully.
- 8007
- MESSAGE
The processing of the :JOB/:DATA record was interrupted before it could logon.
- 8008
- MESSAGE
The setting of the spoolfile ID for the JOB's STDIN failed. The job will be flushed.
- 8009
- MESSAGE
The scheduling of the JOB failed. The job will be flushed.
- 8010
- MESSAGE
The scheduling of the future JOB failed. The job will be flushed.
- 8011
- MESSAGE
An error occurred while printing the JOB number/DATA spoolfile ID.
- 8050
- MESSAGE
Input spooler, LDEV #\: The spooler did not find a valid :JOB or :DATA command on the current tape volume.
- 8051
- MESSAGE
Input spooler, LDEV #\: Device has reported a power failure or other interruption while input spooling.
- 8052
- MESSAGE
Input spooler, LDEV #\: The spooler detected a non-fatal condition while performing an internal calculation. Please report the warning number to your support engineer. The spooler will continue.
- 8053
- MESSAGE
Input spooler, LDEV #\: The File System reported a warning while acquiring the spooled device. The spooler will continue.
- 8054
- MESSAGE
Input spooler, LDEV #\: The Device Allocation subsystem reported a warning while the spooler was retrieving device configuration information. The spooler will continue.
- 8055
- MESSAGE
Input spooler, LDEV #\: The Device Allocation subsystem reported a warning while the spooler was updating device configuration information. The spooler will continue.
- 8056
- MESSAGE
Input spooler, LDEV #\: A warning occurred while converting the LDEV number to a device name.
- 8100
- MESSAGE
Input spooler, LDEV #\: Started.
- 8101
- MESSAGE
Input spooler, LDEV #\: Stopped.
- 8102
- MESSAGE
Input spooler, LDEV #\: Please mount the first tape volume to be input spooled.
- 8103
- MESSAGE
Input spooler, LDEV #\: Please mount the next tape volume to be input spooled.
- 8500
- MESSAGE
Input spooling code received an unexpected escape during normal execution.
- 8501
- MESSAGE
You cannot run the input spooler as a user program.
- 8502
- MESSAGE
Encountered error while using HPFOPEN to open the source file.
- 8503
- MESSAGE
The input spooling code received an I/O error while reading from the source file being input spooled.
- 8504
- MESSAGE
HPFOPEN to open a new input spoolfile failed.
- 8505
- MESSAGE
FCLOSE to close a new input spoolfile failed.
- 8506
- MESSAGE
The record read from the source file has more than 279 characters.
- 8507
- MESSAGE
I/O error during FWRITE to input spoolfile.
- 8508
- MESSAGE
Attempt to deallocate the JMAT entry of a JOB failed.
- 8509
- MESSAGE
An undefined state was encountered during the input spooling process.
- 8510
- MESSAGE
An undefined record kind was received from the source file.
- 8511
- MESSAGE
The source file to be input spooled is not an ASCII data file.
- 8512
- MESSAGE
The call to SP_FM_SET reported an error while updating the SPFDIR entry for the input spoolfile.
- 8513
- MESSAGE
The FFILEINFO intrinsic reported an error while retrieving information about the input spoolfile.
- 8514
- MESSAGE
The GETINFO intrinsic reported an error while retrieving information about the spooled device.
- 8515
- MESSAGE
The conversion of the source file ldev to device name failed.
- 8516
- MESSAGE
An error occurred while retrieving information about the source device.
- 8517
- MESSAGE
An error occurred while delimiting the source device's LDEV name.
- 8518
- MESSAGE
An error occurred while writing a log record to the system log file for the new input spoolfile.
- 8519
- MESSAGE
An error occurred while locking the spoolfile's GUFD.
- 8520
- MESSAGE
An error occurred while locking the input SPFDIR.
- 8521
- MESSAGE
An error occurred while looking for the spoolfile's entry in the SPFDIR.
- 8522
- MESSAGE
An error occurred while updating the owner and creator names in the spoolfile's file label and FLABX.
- 8523
- MESSAGE
An error occurred while unlocking the input SPFDIR.
- 8524
- MESSAGE
An error occurred while unlocking the input spoolfile's GUFD.
- 8550
- MESSAGE
Input spooler, LDEV #\: The spooler detected a fatal condition while performing an internal calculation. Please report the spooling subsystem error to your support engineer.
- 8551
- MESSAGE
Input spooler, Device Name !: Cannot retrieve LDEV# or other configuration info.
- 8552
- MESSAGE
Input spooler, LDEV #: Cannot update device configuration tables.
- 8553
- MESSAGE
Input spooler, LDEV #: Cannot open physical device.
- 8554
- MESSAGE
Input spooler, LDEV #: HPFOPEN of a new input spoolfile failed.
- 8555
- MESSAGE
Input spooler, LDEV #: FCLOSE of a new input spoolfile failed.
- 8556
- MESSAGE
Input spooler, LDEV #: I/O error during FWRITE to input spoolfile.
- 8557
- MESSAGE
Input spooler, LDEV #: Cannot update the input spoolfile's entry in the Spoolfile Directory.
- 8558
- MESSAGE
An error occurred when receiving message from the spooler port.
- 8559
- MESSAGE
Input spooler, LDEV #: An invalid msg type was received by the input spooling process.
- 8560
- MESSAGE
Input spooler, LDEV #: The input spooled device no longer accepts :JOB or :DATA. Spooling will be stopped.
- 8561
- MESSAGE
Input spooler, LDEV #: Failed to rewind and unload current tape volume. Must be done manually. Spooling will be stopped.
- 8562
- MESSAGE
Input spooler, LDEV #: Spooler internal error, RECOVER invoked, spooler terminating.
- 8563
- MESSAGE
Input spooler, LDEV #: A fatal error was encountered by the input spooling process. Spooling will be stopped.
- 8564
- MESSAGE
Input spooler, LDEV #: A fatal error was encountered while converting the LDEV number to a device name. Spooling will be stopped.
- 9001
- MESSAGE
Output spooler, LDEV #: Started.
- 9002
- MESSAGE
Output Spooler, LDEV #: Stopped.
- 9003
- MESSAGE
Output spooler, LDEV #: Suspended.
- 9004
- MESSAGE
Output spooler, LDEV #: Resumed.
- 9005
- MESSAGE
Output spooler, LDEV #: File released successfully.
- 9006
- MESSAGE
Output spooler, LDEV #: Spoolfile EOF detected. NOTE: This message is never displayed.
- 9007
- MESSAGE
Output spooler, LDEV #: The File System reported a warning while acquiring the spooled device. The spooler will continue.
- 9008
- MESSAGE
Output spooler, LDEV #: The spooler detected a non-fatal condition while initializing its device. The spooler will continue.
- 9010
- MESSAGE
Output spooler, LDEV #: The Directory subsystem reported a warning while trying to create the checkpoint file group. The spooler will continue.
- 9011
- MESSAGE
Output spooler, LDEV #: The Device Allocation subsystem reported a warning while the spooler was retrieving device configuration information. The spooler will continue.
- 9012
- MESSAGE
Output spooler, LDEV #: The Device Allocation subsystem reported a warning while the spooler was updating device configuration information. The spooler will continue.
- 9013
- MESSAGE
Output spooler, LDEV #: The spooler detected a non-fatal condition while trying to ;RELEASE a file. The file is released and the spooler will continue.
- 9014
- MESSAGE
Output spooler, LDEV #: The spooler detected a non-fatal condition while determining its next task. The spooler will continue.
- 9015
- MESSAGE
Output spooler, LDEV #: The spooler detected a non-fatal condition while performing an internal calculation. Please report the warning number to your support engineer. The spooler will continue.
- 9016
- MESSAGE
Output spooler, LDEV #/: The spooler detected a non-fatal condition while retrieving information from the Spooling Process Information Table (SPIT). The spooler will continue.
- 9017
- MESSAGE
Output spooler, LDEV #: The spooler detected a non-fatal condition while updating the Spooling Process Information Table (SPIT). The spooler will continue.
- 9018
- MESSAGE
Output spooler, LDEV #: The spooler was unable to save the page number to resume at. It will continue to use the previous value of this page.
- 9019
- MESSAGE
Output spooler, LDEV #: The restart page specified is before the beginning of the spoolfile. The spooler will restart at the beginning.
- 9020
- MESSAGE
Output spooler, LDEV #: There is no file to output at this time. (NOTE: This message is never displayed.)
- 9021
- MESSAGE
Output spooler, LDEV #: Received a command while outputting a file.
- CAUSE
An operator command, such as SPOOLER <ldev>;STOP was received by the spooler process for <ldev> while the process was printing user data.
- ACTION
No action is required. The message is to reassure the operator that the spooler got the command, because the printer may continue to print for some time afterward due to the large amount of buffered data in the file system path.
- 9022
- MESSAGE
Output spooler, LDEV #: The device has reported a power failure or other interruption while outputting SPOOLID #0!. The spooler will attempt recovery.
- CAUSE
The spooled device lost power while printing user data, causing it to lose track of where it was printing on the page. When power is restored, the the device reports the power loss to the spooler.
- ACTION
No user action is required. The spooler will try to recover to the beginning of the page which was partially printed at the time the device lost power.
- 9023
- MESSAGE
Output spooler, LDEV #: Device status is available. (NOTE: This message is never displayed.)
- 9024
- MESSAGE
Output spooler, LDEV #: "Actual device status" cannot be requested in this context. "Buffered status" will be used.
- 9025
- MESSAGE
Output spooler, LDEV #: The device was still in silent-run mode when the spooler detected the end of SPOOLID #0!.
- CAUSE
Silent-run is a recovery mechanism in which the device interprets, but does not print, data until it reaches the page at which printing should resume. If the spooler detects the end of the spoolfile first, it defers the file.
- ACTION
Enter SPOOLF <spoolid>;UNDEFER to print the file from the beginning. Once the file is printing, use SPOOLER ...;SUSPEND and ;RESUME with OFFSET= if you want to print from a different location.
- 9026
- MESSAGE
Output spooler, LDEV #: The device reported a ribbon malfunction. The spooler will suspend. Enter a command to resume operation or to stop.
- 9027
- MESSAGE
Output spooler, LDEV #: A request to mount special forms for SPOOLID #0! was refused by the device attender.
- CAUSE
During the forms message dialog, the operator REPLYed N to the question: SP#<pin>/IS #<spoolid>; <filename> ON LDEV#<ldev> (Y/N)?
- ACTION
If the file should be printed on another device, enter SPOOLF <spoolid>; DEV= <new device>;UNDEFER. If it should be printed on this device but at a later time, enter SPOOLF <spoolid>; UNDEFER at that time.
- 9028
- MESSAGE
Output spooler, LDEV #: The restart page specified is greater than 2^32-1, the maximum value allowed. The spooler will use the maximum value.
- 9029
- MESSAGE
Output spooler, LDEV #: Device has reported a power failure or other interruption while outputting the header for SPOOLID #O!. The spooler will reprint the header.
- CAUSE
The spooled device lost power while printing the header, causing it to lose track of where it was printing on the page. When power is restored, the device reports the power loss to the spooler.
- ACTION
No user action is required. The spooler automatically reprints the header.
- 9030
- MESSAGE
Output spooler, LDEV #: Device has reported a power failure or other interruption while outputting the trailer for SPOOLID #O!. The spooler will reprint the trailer.
- CAUSE
The spooled device lost power while printing the trailer, causing it to lose track of where it was printing on the page. When power is restored, the device reports the power loss to the spooler.
- ACTION
No user action is required. The spooler automatically reprints the trailer.
- 9031
- MESSAGE
Output spooler, LDEV #: Device has reported a power failure or other interruption while outputting the error trailer for SPOOLID #O!. The spooler will reprint the error trailer.
- CAUSE
The spooled device lost power while printing the error trailer, causing it to lose track of where it was printing on the page. When power is restored, the device reports the power loss to the spooler.
- ACTION
No user action is required. The spooler automatically reprints the error trailer.
- 9032
- MESSAGE
Output spooler, LDEV # \ Unable to connect to printer socket after waiting ! seconds, the maximum configured for this printer. The spooler will continue trying to connect to the printer.
- 9033
- MESSAGE
Output spooler, LDEV #\: The file name in the following message has been truncated to ! characters, the maximum length allowed in the message.
- 9034
- MESSAGE
Output spooler, LDEV #\: FLABELINFO reported the following file system error while accessing NPCONFIG setup file !.
- 9035
- MESSAGE
Output spooler, LDEV #\: Expected fixed, variable, undefined, or bytestream records for NPCONFIG setup file !.
- 9036
- MESSAGE
Output spooler, LDEV #\: HPFOPEN error while opening NPCONFIG setup file !.
- 9037
- MESSAGE
Output spooler, LDEV #\: File system error while FREADing NPCONFIG setup file !.
- 9038
- MESSAGE
Output spooler, LDEV #\: Device does not support page level recovery. Any interrupted document will be entirely reprinted.
- 9039
- MESSAGE
Output spooler, LDEV #\: Socket tracing for spoolfile !, copy ! enabled to file !
- 9040
- MESSAGE
Output spooler, LDEV #\: Socket and transport tracing for spoolfile !, copy ! enabled to file !
- 9041
- MESSAGE
Output spooler, LDEV #\: Check NPCONFIG. The valid range of item "!" is ! to !. The spooler will use the default value, !.
- 9042
- MESSAGE
Output spooler, LDEV #\: Check NPCONFIG. Valid values of item "!" are ! and !. The spooler will use the default value, !.
- 9401
- MESSAGE
Output spooler, LDEV #: Spoolfile error. There is an FCLOSE record which does not have a matching FOPEN record.
- 9402
- MESSAGE
Output spooler, LDEV #: The spooler process is temporarily out of heapspace. This checkpoint file cannot be processed properly.
- 9403
- MESSAGE
Output spooler, LDEV #: The spooler encountered an attempt to read the checkpoint file outside of its size.
- 9404
- MESSAGE
Output spooler, LDEV #: The spooler encountered a logical error in interpreting the contents of a checkpoint file.
- 9405
- MESSAGE
Output spooler, LDEV #: The spooler retrieved an entry of unknown type from the checkpoint file queues.
- 9406
- MESSAGE
Output spooler, LDEV #: The spooler received a bad status from an FPOINT call while trying to set the EOF for the checkpoint file.
- 9407
- MESSAGE
Output spooler, LDEV #: The spooler received a bad status from an FCONTROL call while trying to set the EOF for the checkpoint file.
- 9408
- MESSAGE
Output spooler, LDEV #: The spooler was asked to purge checkpoint files for a spoolfile which is not an output spoolfile.
- 9409
- MESSAGE
Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an HPDIRECSETUP error.
- 9410
- MESSAGE
Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an HPDIRECREAD error.
- 9411
- MESSAGE
Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an HPFOPEN error.
- 9412
- MESSAGE
Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an FCLOSE error.
- 9413
- MESSAGE
Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an FCLOSE error.
- 9414
- MESSAGE
Output spooler, LDEV #: The spooler could not close the checkpoint files due to an FCLOSE error.
- 9415
- MESSAGE
Output spooler, LDEV #: The spooler could not open the checkpoint file to use while printing a spoolfile.
- 9416
- MESSAGE
Output spooler, LDEV #: The spooler encountered a trap while attempting a mapped file write to the checkpoint file.
- 9417
- MESSAGE
Output spooler, LDEV #: The spooler encountered an unknown trap in the checkpoint file write procedure.
- 9418
- MESSAGE
Output spooler, LDEV #: The spooler encountered an unknown trap in the checkpoint file read procedure.
- 9419
- MESSAGE
Output spooler, LDEV #: The spooler encountered an unknown escape while purging checkpoint files for the spoolfile file manager.
Spooler 9500 - 32767
- 9501
- MESSAGE
Output spooler, LDEV #: Cannot create the checkpoint file group.
- 9502
- MESSAGE
Output spooler, Device Name !: Cannot retrieve LDEV # or other configuration information.
- 9503
- MESSAGE
Output spooler, LDEV #: Cannot update device configuration tables.
- 9504
- MESSAGE
Output spooler, LDEV #: Could not save special forms information in device configuration tables.
- 9505
- MESSAGE
Output spooler, LDEV #: Cannot open physical device.
- 9506
- MESSAGE
Output spooler, LDEV #: The file system reported an error when the spooler tried to enable the device's reporting status. The spooler cannot continue.
- 9507
- MESSAGE
Output spooler, LDEV #: The file system reported an error when the spooler tried to disable the device's reporting status. The spooler cannot continue.
- 9508
- MESSAGE
Output spooler, LDEV #: Spooler internal error, RECOVER invoked, spooler terminating.
- 9509
- MESSAGE
Output spooler, LDEV #: NM message system error. NOTE: This error is never displayed.
- 9510
- MESSAGE
Output spooler, LDEV #: CM message system error. NOTE: This error is never displayed.
- 9511
- MESSAGE
Output spooler, LDEV #: The spooler could not complete output of file !.
- 9512
- MESSAGE
Output spooler, LDEV #: Spoolfile directory error while deferring file !.
- 9513
- MESSAGE
Output spooler, LDEV #: Spoolfile directory error while saving last page number of file ! to be output.
- 9514
- MESSAGE
Output spooler, LDEV #: Unknown directory service error.
- 9515
- MESSAGE
You cannot run the output spooler as a user program.
- 9516
- MESSAGE
Output spooler: The GETINFO intrinsic reported an error while retrieving information about the spooled device. The spooler process cannot continue.
- 9517
- MESSAGE
Output spooler, LDEV #: The FFILEINFO intrinsic reported an error while retrieving a spoolfile name. The spooler process continues without it.
- 9518
- MESSAGE
Output spooler, LDEV #: Error while trying to set spooler state to STOP. The spooler will terminate anyway.
- 9519
- MESSAGE
Output spooler, LDEV #: Error while trying to set spooler state to ACTIVE.
- 9520
- MESSAGE
Output spooler, LDEV #: Error while trying to set spooler state to SUSPEND.
- 9521
- MESSAGE
Output spooler, LDEV #: Error while trying to set spooler state to IDLE.
- 9522
- MESSAGE
Output spooler, LDEV #: Error while trying to set spooler state to START.
- 9523
- MESSAGE
Output spooler, LDEV #: The spooler entered the INIT state, illegal once the process has started. Please contact your Hewlett-Packard support representative.
- 9524
- MESSAGE
Output spooler, LDEV #: The spooler entered an unknown and illegal state. Please contact your Hewlett-Packard support representative.
- 9525
- MESSAGE
Output spooler, LDEV #: Unable to determine next command.
- 9526
- MESSAGE
Output spooler, LDEV #: The spooler failed to open an output spoolfile. The spooler will go idle until another file becomes ready or until you enter a command which affects the spooling process.
- 9527
- MESSAGE
Output spooler, LDEV #: Internal error while deferring file !, illegal reason for deferral. Please report the spooling subsystem number to your support engineer.
- CAUSE
When the spooler defers a file, it is for one of four causes (each described elsewhere in this document). In this case, the spooler has detected some other cause. This should never happen.
- ACTION
This message indicates a serious error in the code or the system as a whole. Report its number to your HP support representative.
- 9528
- MESSAGE
Output spooler, LDEV #: The spooler failed to close spoolfile !.
- 9529
- MESSAGE
Output spooler, LDEV #: The spooler detected an error opening or accessing checkpoint file ! for spoolfile !. Operation continues without it.
- 9530
- MESSAGE
Output spooler, LDEV #: A spoolfile directory error occurred while selecting a file to print.
- 9531
- MESSAGE
Output spooler, LDEV #: A spoolfile directory error occurred while preparing the Header.
- 9532
- MESSAGE
Output spooler, LDEV #: A spoolfile directory error occurred while preparing the Trailer.
- 9533
- MESSAGE
Output spooler, LDEV #: A spoolfile directory error occurred while getting the user's file designator for forms message processing.
- 9534
- MESSAGE
Output spooler, LDEV #: A spoolfile directory error occurred while updating print job statistics during End of Job.
- 9535
- MESSAGE
Output spooler, LDEV #: A spoolfile directory error occurred while obtaining print job information for the system log file.
- 9536
- MESSAGE
Output spooler, LDEV #: A devicefile information error occurred while obtaining print job information for the system log file.
- 9537
- MESSAGE
Output spooler, LDEV #: The system logging subsystem reported an error while obtaining print job information for the system log file.
- 9538
- MESSAGE
Output spooler, LDEV #: The file system reported a device error during Start of Job processing.
- 9539
- MESSAGE
Output spooler, LDEV #: The file system reported a device error during Header processing.
- 9540
- MESSAGE
Output spooler, LDEV #: The file system reported a device error while outputting data.
- 9541
- MESSAGE
Output spooler, LDEV #: The file system reported a device error while retrieving device status.
- 9542
- MESSAGE
Output spooler, LDEV #: The file system reported a device error during spooler forms message processing.
- 9543
- MESSAGE
Output spooler, LDEV #: The file system reported a device error while printing the error trailer.
- 9544
- MESSAGE
Output spooler, LDEV #: The file system reported a device error during Trailer processing.
- 9545
- MESSAGE
Output spooler, LDEV #: The file system reported a device error during the End of Job processing.
- 9546
- MESSAGE
Output spooler, LDEV #: FCONTROL error.
- 9547
- MESSAGE
Output spooler, LDEV #: FDEVICECONTROL error.
- 9548
- MESSAGE
Output spooler, LDEV #: FREAD error.
- 9549
- MESSAGE
Output spooler, LDEV #: FWRITE error.
- 9550
- MESSAGE
Output spooler, LDEV #: The spooler received an error while waiting for nowait I/O completion.
- 9551
- MESSAGE
Output spooler, LDEV #: The spooler was unable to ;RELEASE the specified file. It remains in KEEP.
- 9552
- MESSAGE
Output spooler, LDEV #: Error while RESUMEing. The spooler will attempt to continue.
- 9553
- MESSAGE
Output spooler, LDEV #: Error while SUSPENDing. The spooler will attempt to continue.
- 9554
- MESSAGE
Output spooler, LDEV #: The spooler received a port read error.
- 9555
- MESSAGE
Output spooler, LDEV #: The spooler received an invalid message type on its port.
- 9556
- MESSAGE
Output spooler, LDEV #: The spooler received an unexpected escape during normal processing.
- 9557
- MESSAGE
Output spooler, LDEV #: The spooler detected a fatal condition while performing an internal calculation. Please report the spooling subsystem error number to your support engineer.
- 9558
- MESSAGE
Output spooler, LDEV #: The spooler could not access the Spooling Process Information Table (SPIT).
- 9559
- MESSAGE
Output spooler, LDEV #: The spooler failed to update the Spooling Process Information Table (SPIT).
- 9560
- MESSAGE
Output spooler, LDEV #: Spoolfile internal format error, attempted to access beyond file bounds. The file will be deferred.
- 9561
- MESSAGE
Output spooler, LDEV #: Unsupported internal function code "!". Legal values are 1-4 and 64-255.
- 9562
- MESSAGE
Output spooler, LDEV #: The device storage manager reported an invalid device status type "!". Please report the type and the spooling subsystem error number to your support engineer.
- 9563
- MESSAGE
Output spooler, LDEV #: The device reported a parity or self-test error.
- 9564
- MESSAGE
Output spooler, LDEV #: The device has insufficient memory to process data in this file.
- 9565
- MESSAGE
Output spooler, LDEV #: The device has reported 100 protocol errors while processing this file.
- 9566
- MESSAGE
Output spooler, LDEV #: The device has reported 100 instances of data overrun while processing this file.
- 9567
- MESSAGE
Output spooler, LDEV#\: The required HPSPOOL account is missing. The spooler cannot continue.
- 9568
- MESSAGE
Output spooler, LDEV #: The spooler could not open CATALOG.PUB.SYS to format the error trailer for SPOOLID #O!. The spooler will continue without printing the error trailer.
- CAUSE
The spooler could not FOPEN CATALOG.PUB.SYS. The reason for this failure is displayed following this message.
- ACTION
Correct the problem with CATALOG.PUB.SYS. This allows the spooler to print future error trailers, however the spooler will not print any error trailers until the problem is corrected.
- 9569
- MESSAGE
Output spooler, LDEV #: The GENMESSAGE intrinsic reported error ! while formatting the error trailer for SPOOLID #O!. The spooler will continue without printing the error trailer.
- CAUSE
Self-explanatory.
- ACTION
Determine the cause of the GENMESSAGE error and correct it. This allows the spooler to print future error trailers, however the spooler will not print any error trailers until the problem is corrected.
- 9570
- MESSAGE
Output spooler, LDEV #: The spooler detected a non-fatal condition while performing an internal calculation to print the error trailer for SPOOLID #O!. The spooler will continue without finishing the error trailer.
- CAUSE
Corruption in the list of messages which make up the error trailer. The index into the list exceeded the maximum number of possible elements in the list without detection of the end-of-list mark.
- ACTION
Report the message number to your support engineer.
- 9571
- MESSAGE
Output spooler, LDEV #: Could not set (clear) serial printer transparent mode.
- 9572
- MESSAGE
Output spooler, LDEV #\: Spoolfile ! deferred due to a user command.
- CAUSE
A user entered a SPOOLF <spoolid set>;DEFER or ALTSPOOLFILE <spoolid -or- ldev> ; DEFER which referenced the file currently being printed by this device's spooler.
- ACTION
This message is informational. No action is required.
- 9573
- MESSAGE
Output spooler, LDEV #\: Spoolfile ! deferred due to a file error or abnormal condition.
- CAUSE
The file system reported an error while accessing the spoolfile.
The spooler detected internal spoolfile format corruption.
- ACTION
Either of the above reasons generates an appropriate error message. Correct the situation if possible, then SPOOLF...;UNDEFER the file to try to reprint the file.
- 9574
- MESSAGE
Output spooler, LDEV #\: The spooler was unable to send a message to its port.
- CAUSE
The MPE/iX Ports Facility returned an error status to the spooler. The spooler process will terminate.
- ACTION
This should never happen. If it does, record all displayed messages, restart the spooler process and contact your Hewlett-Packard representative.
- 9575
- MESSAGE
Output spooler, LDEV #\: Error while trying to set spooler state to SUSPEND PENDING.
- CAUSE
An internal routine which modifies the running state of the spooler process reported an error status to the spooler. The spooler process will terminate.
- ACTION
This should never happen. If it does, record all displayed messages, restart the spooler process and contact your Hewlett-Packard representative.
- 9576
- MESSAGE
Output spooler, LDEV #\: The spooler was unable to flush its data to the printer due to a closed connection socket.
- 9578
- MESSAGE
Output spooler, LDEV #\: Error while performing the TCP graceful release handshake on the printer connection.
- 9579
- MESSAGE
Output spooler, LDEV #\: Error while waiting for the printer to flush its buffered data.
- 9580
- MESSAGE
Output spooler, LDEV #\: Unable to complete ABORTIO request to the printer connection socket.
- 9581
- MESSAGE
Output spooler, LDEV #\: IPC error while trying to close the printer connection socket. IPCSHUTDOWN error !:
- 9582
- MESSAGE
Output spooler, LDEV #\: IPC error while trying to open a printer connection socket. ADDOPT error !:
- 9583
- MESSAGE
Output spooler, LDEV #\: IPC error while trying to open a printer connection socket. IPCDEST error !:
- 9584
- MESSAGE
Output spooler, LDEV #\: IPC error while trying to write to the printer connection socket. IPCSEND error !:
- 9585
- MESSAGE
Output spooler, LDEV #\: IPC error while trying to open a printer connection socket. IPCCONNECT error !:
- 9586
- MESSAGE
Output spooler, LDEV #\: IOWAIT message destination error, sent to (spooler) port !, intended for port !.
- 9587
- MESSAGE
Output spooler, LDEV #\: IPC error while initializing a printer connection socket. IPCRECV error !:
- 9588
- MESSAGE
Output spooler, LDEV #\: IPC error while enabling or aborting a nowait I/O socket request. IPCCONTROL error !:!!
- 9589
- MESSAGE
Output spooler, LDEV #\: Could not identify a network address for this printer. The spooler will terminate. Check NPCONFIG.PUB.SYS.
- 9590
- MESSAGE
Output spooler, LDEV #\: The IOWAIT intrinsic reported a printer socket error, or an ABORTIO request was received.
- 9591
- MESSAGE
Output spooler, LDEV #\: Internal error, buffer not available as expected.
- 9592
- MESSAGE
Output spooler, LDEV #\: Failed to send buffered data to printer socket.
- 9593
- MESSAGE
Output spooler, LDEV #\: I/O aborted by user command.
- 9594
- MESSAGE
Output spooler, LDEV #\: The IOWAIT intrinsic reported condition code !.
- 9595
- MESSAGE
Output spooler, LDEV #\: Internal error, the IOWAIT intrinsic completed a request with a 0 file descriptor.
- 9596
- MESSAGE
Output spooler, LDEV #\: IPC error while reading printer status. IPCRECV error !:!!
- 9597
- MESSAGE
Output spooler, LDEV #\: The IOWAIT intrinsic reported I/O completion on file descriptor !, expected IOWAIT file descriptor ! or printer socket file descriptor !.
- 9598
- MESSAGE
Output spooler, LDEV #\: Failed to write PJL JOB command to printer. Check other error messages.
- 9599
- MESSAGE
Output spooler, LDEV #\: During spooler initialization, failed to get PLFD entry for use by IOWAIT port. The spooler will terminate.
- 9600
- MESSAGE
Output spooler, LDEV #\: During spooler initialization, failed to create OWAIT port. The spooler will terminate.
- 9601
- MESSAGE
Output spooler, LDEV #\: Network printer internal message identifier mismatch, ID was '!', expected '!'.
- 9602
- MESSAGE
Output spooler, LDEV #\: Internal IOWAIT message type "!" is not valid in this context.
- 9603
- MESSAGE
Output spooler, LDEV #\: Invalid IOWAIT message type.
- 9604
- MESSAGE
Output spooler, LDEV #\: Failed to obtain a system timer entry.
- 9605
- MESSAGE
Output spooler, LDEV #\: The IOWAIT intrinsic reported I/O completion on file descriptor !, expected IOWAIT file descriptor !.''
- 9606
- MESSAGE
Output spooler, LDEV #\: Failed to abort a timer request.
- 9607
- MESSAGE
Output spooler, LDEV #\: During spooler initialization, failed to locate IOWAIT completion routine. The spooler will terminate.
- 9608
- MESSAGE
Output spooler, LDEV #\: Unable to flush ! pending completions from IOWAIT port ! prior to spooler shutdown.
- 9609
- MESSAGE
Output spooler, LDEV #\: Failed to write PJL USTATUS command to printer. Check other error messages.
- 9610
- MESSAGE
Output spooler, LDEV #\: Unable to flush all data to printer at end of spool file.
- 9611
- MESSAGE
Output spooler, LDEV #\: During spooler initialization, could not notify the LDEV's logical device manager. The spooler will terminate.
- 9612
- MESSAGE
Output spooler, LDEV #\: During spooler termination, could not notify the LDEV's logical device manager.
- 9613
- MESSAGE
Output spooler, LDEV #\: Sequence error, buffered data remains to be printed after the printer connection has been released.
- 9614
- MESSAGE
Output spooler, LDEV #\: Unable to close printer socket. The spooler will try to continue with the present connection.
- 9615
- MESSAGE
Output spooler, LDEV #\: Error while waiting for internal timed event to end.
- 9616
- MESSAGE
Output spooler, LDEV #\: Received an error at line ! of NPCONFIG.PUB.SYS while retrieving configuration information.
- 9617
- MESSAGE
Output spooler, LDEV #\: Failed to release timer entry !.
- 9618
- MESSAGE
Output spooler, LDEV #\: Could not write ending PJL commands to printer.
- 9619
- MESSAGE
Output spooler, LDEV #\: File system error: !!
- 9620
- MESSAGE
Output spooler, LDEV #\: The ! bytes of PJL printer status exceed the ! bytes available to hold it.
- 9621
- MESSAGE
Output spooler, LDEV #\: The PJL information returned from the printer contains a syntax error. The first ! (max) bytes are shown: !
- 9622
- MESSAGE
Output spooler, LDEV #\: Unable to deallocate heap space used while processing NPCONFIG items. The spooler will continue.
- 9623
- MESSAGE
Output spooler, LDEV #\: Unable to open network printer configuration file NPCONFIG.PUB.SYS.
- 9624
- MESSAGE
Output spooler, LDEV #\: Internal error, NPCONFIG processing routines detected an LDEV number outside the range of 1 to 10000000.
- 9625
- MESSAGE
Output spooler, LDEV #\: No entry for this LDEV in NPCONFIG.PUB.SYS.
- 9626
- MESSAGE
Output spooler, LDEV #\: Syntax error in NPCONFIG.PUB.SYS, missing LDEV specification.
- 9627
- MESSAGE
Output spooler, LDEV #\: Syntax error in NPCONFIG.PUB.SYS, missing closing parenthesis.
- 9628
- MESSAGE
Output spooler, LDEV #\: Syntax error in NPCONFIG.PUB.SYS, missing opening parenthesis.
- 9629
- MESSAGE
Output spooler, LDEV #\: Syntax error in NPCONFIG.PUB.SYS, unexpected opening parenthesis.
- 9630
- MESSAGE
Output spooler, LDEV #\: Syntax error in NPCONFIG.PUB.SYS, unexpected closing parenthesis.
- 9631
- MESSAGE
Output spooler, LDEV #\: Syntax error in NPCONFIG.PUB.SYS, missing equal sign (=).
- 9632
- MESSAGE
Output spooler, LDEV #\: Syntax error in NPCONFIG.PUB.SYS, unexpected equal sign (=).
- 9633
- MESSAGE
Output spooler, LDEV #\: Syntax error in NPCONFIG.PUB.SYS.
- 9634
- MESSAGE
Output spooler, LDEV #\: Internal error in NPCONFIG parser, parser stack overflow.
- 9635
- MESSAGE
Output spooler, LDEV #\: Internal error in NPCONFIG parser.
- 9636
- MESSAGE
Output spooler, LDEV #\: Error while switching the printer into its PCL personality.
- 9637
- MESSAGE
Output spooler, LDEV #\: Could not flush buffered data to printer at end-of-job.
- 9638
- MESSAGE
Output spooler, LDEV #\: Error while waiting for printer to process all data during end-of-job.
- 9639
- MESSAGE
Output spooler, LDEV #\: The spooler was unable to write its data to the printer due to a closed connection socket.
- 9640
- MESSAGE
Output spooler, LDEV #\: The spooler detected an unexpected open connection socket. The spooler will close the socket and continue.
- 9641
- MESSAGE
Output spooler, LDEV #\: The spooler detected unprinted data in its internal buffers. Some output may have been lost.
- 9642
- MESSAGE
Output spooler, LDEV #\: Failed to open the debug log file. The spooler will continue, but will not log any events.
- 9643
- MESSAGE
Output spooler, LDEV #\: Failed while writing to the debug log file. The spooler will continue, but will not log any more events.
- 9644
- MESSAGE
Output spooler, LDEV #\: Failed to close the debug log file.
- 9645
- MESSAGE
Output spooler, LDEV #\: Failed to reset the printer at start of either header, data, or trailer.
- 9646
- MESSAGE
Output spooler, LDEV #\: The IPCRECV intrinsic reported error ! while waiting for a generic event completion. The error text is: !!
- 9647
- MESSAGE
Output spooler, LDEV #\: Unable to reconnect to printer socket after an abnormal disconnection.
- 9648
- MESSAGE
Output spooler, LDEV #\: Failed to setup internal data structures for printer SNMP requests due to previous error(s).
- 9649
- MESSAGE
Output spooler, LDEV #\: Failed to close the UDP socket used for printer status requests.
- 9650
- MESSAGE
Output spooler, LDEV #\: Error while writing to printer display panel.
- 9651
- MESSAGE
Output spooler, LDEV #\: Network error or write error while downloading NPCONFIG setup file !.
- 9652
- MESSAGE
Output spooler, LDEV #\: Non-spooling subsystem error while processing NPCONFIG setup file !.
- 9653
- MESSAGE
Output spooler, LDEV #\: Internal error while downloading setup file, CREATE_OBJECT call failed. Please report the spooling subsystem error number to your support engineer.
- 9654
- MESSAGE
Output spooler, LDEV #\: Internal error while downloading setup file, RELEASE_OBJECT call failed. Please report the spooling subsystem error number to your support engineer.
- 9655
- MESSAGE
Output spooler, LDEV #\: Spool file ! deferred due to a setup file error or abnormal condition.
- 9656
- MESSAGE
Output spooler, LDEV #\: SNMP error ! reported while retrieving printer status.
- 9657
- MESSAGE
Output spooler, LDEV #\: Failed to write PJL ECHO command to printer. Check other error messages.
- 9658
- MESSAGE
Output spooler, LDEV #\: Operator intervention required. Printer reports the following device status: !!!
- 9659
- MESSAGE
Output spooler, LDEV #\: SNMP query returned a status word with known_state bit not set. Device status cannot be processed.
- 9660
- MESSAGE
Output spooler, LDEV #\: Printer device is not responding. Either the device is not operational or possible network problem.
- 9661
- MESSAGE
Output spooler, LDEV #\: Network transport must be started for network printers to work. Socket error ! reported by IPCCREATE intrinsic: !!
- 9662
- MESSAGE
Output spooler, LDEV #\: Cannot communicate with network printer. Check network xport config, NPONFIG.PUB.SYS, xport and links started status, intermediate network, and printer status.
- 9663
- MESSAGE
Output spooler, LDEV #\: Failed to create a call socket bound to TCP-protocol.
- 9664
- MESSAGE
Output spooler, LDEV #\: Failed to enable socket tracing. Sockets status !, Node Management Services status NMERR !.
- 9665
- MESSAGE
Output spooler, LDEV #\: Domain name resolver return status nodename is unknown (HOST_NOT_FOUND). Printer nodename lookup failed.
- 9666
- MESSAGE
Output spooler, LDEV #\: Domain name resolver return status nameserver not responding (TRY_AGAIN). Printer nodename lookup failed.
- 9667
- MESSAGE
Output spooler, LDEV #\: Some unexpected domain name resolver error was encountered (NO_RECOVERY). Printer nodename lookup failed.
- 9668
- MESSAGE
Output spooler, LDEV #\: Domain name resolver return status incomplete data for requested node (NO_DATA). Printer nodename lookup failed.
- 9669
- MESSAGE
Output spooler, LDEV #\: Unknown domain name resolver error was encountered. Printer nodename lookup failed.
- 9670
- MESSAGE
Output spooler, LDEV #\: The program_file item of NPCONFIG.PUB.SYS must be either OUTSPTJ.PUB.SYS or /SYS/PUB/OUTSPTJ (case sensitive).
- 9671
- MESSAGE
Output spooler, LDEV #\: The run_priority item of NPCONFIG.PUB.SYS must be one of BS, CS, DS, or ES. The spooler will use the default value (CS).
- 9901
- MESSAGE
Output spooler, LDEV #: I/O error, the FCONTROL intrinsic failed while creating the checkpoint file group.
- 9902
- MESSAGE
Output spooler, LDEV #: I/O error, the FDEVICECONTROL intrinsic failed.
- 9903
- MESSAGE
Output spooler, LDEV #: The spooler encountered an unexpected escape while processing an FOPEN or FCLOSE. The escape code is pushed on the stack.
- 9904
- MESSAGE
Output spooler, LDEV #: The spooler encountered an unexpected escape while processing an FCLOSE. The escape code is pushed on the stack.
- 10750
- MESSAGE
Command string contains an invalid PURGE option.
- CAUSE
The PURGE option on the OUTPUT command of the SPFXFER utility was incorrectly specified.
- ACTION
Check and correct the spelling and/or syntax of the OUTPUT command.
- 10751
- MESSAGE
File specifier too long in command string.
- 10752
- MESSAGE
Invalid command name.
- 10753
- MESSAGE
Invalid tape filename in command string.
- 10754
- MESSAGE
Invalid user name in command string.
- 10755
- MESSAGE
Invalid command syntax.
- 10756
- MESSAGE
Invalid delimiter in command string.
- 10757
- MESSAGE
Keyword missing in command string.
- 10758
- MESSAGE
Invalid parameters in command string.
- 10759
- MESSAGE
Command is too long.
- 10760
- MESSAGE
An error has been returned by MYCOMMAND.
- 10761
- MESSAGE
Terminal I/O error.
- 10762
- MESSAGE
No files were found under the specified USER.ACCOUNT.
- 10763
- MESSAGE
Unable to open tape device.
- 10764
- MESSAGE
Cannot open spoolfile on disc.
- 10765
- MESSAGE
Invalid tape format.
- 10766
- MESSAGE
Error while reading tape.
- 10773
- MESSAGE
EOF mark not found.
- 10774
- MESSAGE
Wrong reel - incorrect tape label.
- 10775
- MESSAGE
Wrong real - incorrect reel number.
- 10776
- MESSAGE
Wrong reel - incorrect SPOOK version.
- 10777
- MESSAGE
Unable to close tape device.
- 10778
- MESSAGE
Error while reading file.
- 10779
- MESSAGE
Error while writing file.
- 10780
- MESSAGE
Error while writing to tape.
- 10781
- MESSAGE
File not found.
- 10782
- MESSAGE
Invalid file ID.
- 10785
- MESSAGE
Insufficient capability.
- 10786
- MESSAGE
Unexpected end of tape encountered.
- 10787
- MESSAGE
Wrong reel has been mounted.
- 10788
- MESSAGE
Multi reel abort.
- 10789
- MESSAGE
Error occurred while accessing Native Mode device files.
- 10790
- MESSAGE
Error in SPOOK tape Device Class Directory.
- 10791
- MESSAGE
Invalid spoolfile block format.
- 10792
- MESSAGE
Error while delimiting device name.
- 10793
- MESSAGE
Cannot get UFID.
- 10794
- MESSAGE
Cannot get spoolfile ID.
- 10795
- MESSAGE
Error returned by FCONTROL.
- 10796
- MESSAGE
Error returned by FFILEINFO.
- 10797
- MESSAGE
Cannot open spoolfile on system disc.
- 10798
- MESSAGE
Cannot close spoolfile on system disc.
- 10799
- MESSAGE
Error returned by SP_FM_SET.
- 10800
- MESSAGE
Invalid target device.
- 10801
- MESSAGE
SPOOKTAPE Device Directory overflow.
- 10802
- MESSAGE
Error returned by FCHECK.
- 10803
- MESSAGE
Error returned by SP_FM_INFO.
- 10804
- MESSAGE
Cannot open STDLIST.
- 10805
- MESSAGE
Error returned by Job/Session Procedures.
- 32765
- MESSAGE
Native Mode Spooler message !.
- 32766
- MESSAGE
Native Mode Spooler message !.
|
Loader, Native Mode (Subsystem 104) |
Chapter 3 |