Chapter 6 File System (Native Mode)
(Subsystem 143)
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II | |
| E0300 Volume I ♥ | |
| E0300 Volume II | |
| E0300 Volume III | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
 |
NOTE: This chapter includes KSAM error messages. |
Error (-90) - 199
- -90
- MESSAGE
Problem: The time limit expired before any of the selected for events occurred or before the time limit expired.
- CAUSE
The HPSELECT intrinsic could not select for any of the specified events during the specified time limit.
- ACTION
Increase the time limit, or don't pass it.
- -91
- MESSAGE
Problem: A soft interrupt occurred before any of the selected for events occurred or before the time limit expired.
- CAUSE
A soft interrupt occurred, while the process was blocked on HPSELECT.
- ACTION
None.
- -99
- MESSAGE
The requested information is larger than the return value can express. (FILE SYSTEM ERROR -99)
- CAUSE
A 16 ir 32-bit return value was passed into anintrinsic which needs a larger return value (32 or 64bit) in order to return a correct result.
- ACTION
Call the intrinsic with a new item number that returns the information in a larger return value.
- -342
- MESSAGE
HOP_OPTION_ACD was specified for an HPFOPEN for which this option is not allowed such as for a device or OLD file.
- -353
- MESSAGE
Due to the size of this file, only the LARGE-MAPPED option (87) can be used to open the file for user mapped access. (FILE OPEN ERROR -353)
- -588
- MESSAGE
The ACD option is not valid. The ACD supplied in the HOP_OPTION_ACD keyvalue is invalid or the user does not have access to the buffer.
- -589
- MESSAGE
An error occurred while accessing an ACD. This error is typically returned when the ACD for the file or device being accessed is corrupted.
- -591
- MESSAGE
The creator of a linked spoolfile which was being created "RAW" did not have access to the target device. The spoolfile was created and DEFERred..
- -658
- MESSAGE
Problem: Failure in Creating the File IO State Semaphore Table.
- CAUSE
Procedure FS_INITIALIZE_FILE_SYSTEM failed to create the File IO State Semaphore Table.
- ACTION
Ask your system manager to investigate the problem and reboot the system.
- -659
- MESSAGE
Problem: Failure in initializing The File IO State Semaphore Table.
- CAUSE
Procedure FS_INITIALIZE_FILE_SYSTEM failed to initialize the File IO State Semaphore Table.
- ACTION
Ask your system manager to investigate the problem and reboot the system.
- 1
- MESSAGE
Intrinsic layer; file number is not valid.
- 2
- MESSAGE
Intrinsic layer; the operation could not be completed because caller lacked the proper execution privilege level.
- 3
- MESSAGE
Intrinsic layer; an access violation occurred.
- 4
- MESSAGE
Intrinsic layer; record number is not valid.
- 5
- MESSAGE
Intrinsic layer; number of records is not valid.
- 6
- MESSAGE
Intrinsic layer; the process is out of PLFD's.
- 7
- MESSAGE
Intrinsic layer; the maximum user label size was exceeded.
- 8
- MESSAGE
Intrinsic layer; device type is not valid.
- 9
- MESSAGE
Intrinsic layer; this is an illegal parameter.
- 10
- MESSAGE
Intrinsic layer; this is an unimplemented function.
- 11
- MESSAGE
Intrinsic layer; FLOCK is unable to LOCK file.
- 12
- MESSAGE
Intrinsic layer; the file is not LOCKED.
- 13
- MESSAGE
Intrinsic layer; the file has no user labels.
- 14
- MESSAGE
Intrinsic layer; no WAIT IO pending.
- 15
- MESSAGE
Intrinsic layer; no NOWAIT IO for specific file.
- 16
- MESSAGE
Intrinsic layer; an invalid operation for this device type.
- 17
- MESSAGE
Intrinsic layer; a privilege violation occurred.
- 18
- MESSAGE
Intrinsic layer; a bounds violation occurred.
- 19
- MESSAGE
Intrinsic layer; user does not have multiple RIN capability.
- 20
- MESSAGE
Intrinsic layer; user does not have SAVE capability.
- 21
- MESSAGE
Intrinsic layer; a SECURITY VIOLATION on file occurred.
- 22
- MESSAGE
Intrinsic layer; missing item number or return variable.
- 23
- MESSAGE
Intrinsic layer; a switch failure occurred.
- 24
- MESSAGE
Intrinsic layer; an undefined error occurred.
- 25
- MESSAGE
Intrinsic layer; an OVERFLOW trap occurred.
- 26
- MESSAGE
Intrinsic layer; a CONDITIONAL TRAP occurred.
- 27
- MESSAGE
Intrinsic layer; a FLOATING POINT TRAP occurred.
- 28
- MESSAGE
Intrinsic layer; a data page fault has occurred.
- 29
- MESSAGE
Intrinsic layer; a DATA MEMORY PROTECTION TRAP has occurred.
- 30
- MESSAGE
Intrinsic layer; the reference to this file in this context is not vaild.
- 31
- MESSAGE
Intrinsic layer; the item number passed was out of range.
- 32
- MESSAGE
Intrinsic layer; the operation could not be completed because the file was not opened with exclusive access.
- 33
- MESSAGE
Intrinsic layer; the user of the file must be the creator for this operation.
- 34
- MESSAGE
Intrinsic layer; the operation desired is not consistent with the device type.
- 35
- MESSAGE
Intrinsic layer; RENAME of a file across a volume set was attempted; this is an invalid operation.
- 36
- MESSAGE
Intrinsic layer; the operation was not completed because a nonexistent group was specified.
- 37
- MESSAGE
Intrinsic layer; the operation could not be completed because a nonexistent account was specified.
- 38
- MESSAGE
Intrinsic layer; the operation could not be completed because a nonexistent file was specified.
- 39
- MESSAGE
Intrinsic layer; the operation could not be completed because a nonexistent temporary file was specified.
- 40
- MESSAGE
Intrinsic layer; the operation could not be completed because of insufficient disk space in the group.
- 41
- MESSAGE
Intrinsic layer; the operation could not be completed because of insufficient disk space in the account.
- 42
- MESSAGE
Intrinsic layer; the operation could not be completed because a duplicate permanent file name was specified.
- 43
- MESSAGE
Intrinsic layer; the operation could not be completed because a duplicate temporary file name was specified.
- 44
- MESSAGE
Intrinsic layer; the operation could not be completed because an I/O error occurred in the directory routines.
- 45
- MESSAGE
Intrinsic layer; the operation could not be completed because the file equation used was invalid.
- 46
- MESSAGE
Intrinsic layer; the operation could not be completed because a file equation is required but was not used.
- 47
- MESSAGE
Intrinsic layer; STORGE MANAGEMENT control failed.
- 48
- MESSAGE
The block size of the file is invalid. (FILE SYSTEM ERROR -48)
- CAUSE
The block size specified is not in the range of valid block sizes.
- ACTION
Specify a block size that is valid.
- 49
- MESSAGE
No nowait I/O is outstanding for any file. (FILE SYSTEM ERROR -49)
- CAUSE
A nowait read or write was not initiated against any file prior to calling IOWAIT.
- ACTION
Initiate a nowait I/O prior to calling IOWAIT.
- 50
- MESSAGE
A specified option value was invalid. (FILE SYSTEM ERROR -50)
- CAUSE
An improper value was passed into the intrinsic.
- ACTION
Consult the Intrinsics Manual for valid option values.
- 51
- MESSAGE
The character set number must be between 0 and 31. (FILE SYSTEM ERROR -51)
- CAUSE
An improper character set number was specified.
- ACTION
Specify a valid character set number.
- 52
- MESSAGE
The logical page number must be between 0 and 31. (FILE SYSTEM ERROR -52)
- CAUSE
An improper logical page number was specified.
- ACTION
Specify a valid logical page number.
- 53
- MESSAGE
The number of copies must be between 1 and 32767. (FILE SYSTEM ERROR -53)
- CAUSE
An invalid number of copies was specified.
- ACTION
Specify a valid number of copies.
- 54
- MESSAGE
The page length parm must be between 12 (=3") and 68 (=17"). (FILE SYSTEM ERROR -54)
- CAUSE
An invalid page length was specified.
- ACTION
Specify a valid page length.
- 55
- MESSAGE
The form number must be between 0 and 31. (FILE SYSTEM ERROR -55)
- CAUSE
An invalid form number was specified.
- ACTION
Specify a valid form number.
- 56
- MESSAGE
The number of overlays must be between 1 and 8. (FILE SYSTEM ERROR -56)
- CAUSE
An invalid number of overlays was specified.
- ACTION
Specify a valid number of overlays.
- 57
- MESSAGE
The vertical format number must be between 0 and 31. (FILE SYSTEM ERROR -57)
- CAUSE
An invalid vertical format number was specified.
- ACTION
Specify a valid vertical format number.
- 58
- MESSAGE
The picture number must be between 0 and 31. (FILE SYSTEM ERROR -58)
- CAUSE
An invalid picture nubmer was specified.
- ACTION
Specify a valid picture number.
- 59
- MESSAGE
The extended capability parm must be 0 (off) or 1 (on). (FILE SYSTEM ERROR -59)
- CAUSE
An invalid value for the extended capability parm was specified.
- ACTION
Specify a valid value for the extended capability parm.
- 60
- MESSAGE
The caller lacks sufficient capability to perform the requested operation. (FILE SYSTEM ERROR -60)
- CAUSE
A request was made to perform a privileged operation from an process lacking the necessary capabilities.
- ACTION
Acquire the necessary capabilities prior to calling the function.
- 61
- MESSAGE
A matching UFID could not be found among the opened files for this process. (FILE SYSTEM ERROR -61)
- CAUSE
The target UFID file is not opened by the process.
- ACTION
No action is necessary.
- 62
- MESSAGE
The specified file resides on a read-only volume. (FILE SYSTEM ERROR -62)
- CAUSE
An attempt was made to modify a file on a read-only volume.
- ACTION
Do not attempt to modify a file on a read-only volume.
- 63
- MESSAGE
The filename cannot be expressed using the specified syntax. (FILE SYSTEM ERROR -63)
- CAUSE
The syntax requested to return the filename cannot name the file.
- ACTION
Request the filename in a different syntax.
- 64
- MESSAGE
Renaming a file of the given file type is not supported. (FILE SYSTEM ERROR -64)
- CAUSE
An attempt was made to rename a file type that cannot be renamed.
- ACTION
Do not attempt to rename this file.
- 65
- MESSAGE
The UID/GID database could not be found. (FILE SYSTEM ERROR -65)
- CAUSE
The files HPUID.PUB.SYS and HPGID.PUB.SYS do not exist.
- ACTION
Run PXUTIL.PUB.SYS to create the UID/GID database.
- 66
- MESSAGE
User information was not found in the UID database. (FILE SYSTEM ERROR -66)
- CAUSE
There was no entry for this user in the UID database.
- ACTION
Run PXUTIL.PUB.SYS, or add the user to the database.
- 67
- MESSAGE
File group information was not found in the GID database. (FILE SYSTEM ERROR -67)
- CAUSE
There was no entry for the file group in the GID database.
- ACTION
Run PXUTIL.PUB.SYS, or add the file group to the database.
- 68
- MESSAGE
The caller lacks RACD capability. (FILE SYSTEM ERROR -68)
- CAUSE
The caller has not been granted RACD access to the file.
- ACTION
Have RACD access granted to the user.
- 69
- MESSAGE
A component in the specified pathname is not a directory. (FILE SYSTEM ERROR -69)
- CAUSE
One of the intermediate components of a pathname is not a directory.
- ACTION
Supply a valid pathname.
- 74
- MESSAGE
IS_END_OF_FILE: An instrinsic operation was attempted when the EOF was encountered.
- CAUSE
An instrinsic was called when the data pointer was pointing to the EOF.
- ACTION
Reposition the file data pointer to a valid record.
- 80
- MESSAGE
An internal error occurred. (FILE SYSTEM ERROR -80)
- CAUSE
Something that can not happen did.
- ACTION
File an SR or contact an HP representative.
- 81
- MESSAGE
The operation failed due to a lack of system resources. (FILE SYSTEM ERROR -81)
- CAUSE
One or more system resources were exhausted.
- ACTION
File an SR or contact an HP representative.
- 82
- MESSAGE
FOPTIONs cannot express the physical attributes of this file. (FILE SYSTEM ERROR -82)
- CAUSE
One or more of the physical attributes of the file cannot be represented in the fields of the FOPTIONs.
- ACTION
Retrieve information about each of the file attributes with separate items.
- 83
- MESSAGE
The operation cannot be completed due to the privilege level of the file. (FILE SYSTEM ERROR -83)
- CAUSE
An attempt has been made to create a file with a privilege level other than 3 outside of an MPE group.
- ACTION
Do not attempt this operation with a privileged file.
- 84
- MESSAGE
The operation cannot be completed because the file is write protected. (FILE SYSTEM ERROR -84)
- CAUSE
This file has been protected from write access.
- ACTION
Do not attempt to alter this file.
- 85
- MESSAGE
The operation cannot be completed because the file has a privileged file code. (FILE SYSTEM ERROR -85)
- CAUSE
An attempt has been made to create a file with a privileged file code outside of an MPE group.
- ACTION
Do not attempt this operation with a privileged file code file.
- 86
- MESSAGE
The user lacks traverse access to one of the directory components in the path. (FILE SYSTEM ERROR -86)
- CAUSE
The security attributes of one of the directory components does not allow this user the ability to traverse through the directory.
- ACTION
Have the system or account manager allow the user TD access to the directory.
- 87
- MESSAGE
The record type of this file is not recognized by the system. (FILE SYSTEM ERROR -87)
- CAUSE
A file has somehow been placed on the system that the system does not recognize.
- ACTION
Unlink the file to remove it.
- 88
- MESSAGE
The file type of this file is not recognized by the system. (FILE SYSTEM ERROR -88)
- CAUSE
A file has somehow been placed on the system that the system does not recognize.
- ACTION
Unlink the file to remove it.
- 89
- MESSAGE
The name of this file cannot be expressed in the requested syntax. (FILE SYSTEM ERROR -89)
- CAUSE
The name of this file is not expressable in the syntax requested.
- ACTION
Request the name in a different syntax.
- 90
- MESSAGE
The operation completed due to a time-out. (FILE SYSTEM ERROR -90)
- CAUSE
The operation timed-out before it could be otherwise completed.
- ACTION
If necessary, retry the operation.
- 91
- MESSAGE
The operation was halted due to an interrupt. (FILE SYSTEM ERROR -91)
- CAUSE
An interrupt occurred before the operation could complete.
- ACTION
If necessary, retry the operation.
- 92
- MESSAGE
Files of this file type must reside in the MPE namespace. (FILE SYSTEM ERROR -92)
- CAUSE
An attempt was made to move this file outside the MPE namespace.
- ACTION
Do not attempt to move this file outside the MPE namespace.
- 93
- MESSAGE
A component of the pathname specified does not exist. (FILE SYSTEM ERROR -93)
- CAUSE
One of the components of the path name does not exist.
- ACTION
Check the spelling of each component of the path.
- 94
- MESSAGE
The user lacks create access (CD) to the directory in which a, file is to be created. (FILE SYSTEM ERROR -94)
- CAUSE
The security attributes of the directory node do not allow the user to create an object in the directory.
- ACTION
Have the appropriate person allow CD access to this user.
- 95
- MESSAGE
The user lacks delete access (DD) to the directory in which a file is to be removed. (FILE SYSTEM ERROR -95)
- CAUSE
The security attributes of the directory node do not allow the user to delete an object from the directory.
- ACTION
Have the appropriate person allow DD access to this user.
- 96
- MESSAGE
The Storage Management Subsystem could not open this file. (FILE SYSTEM ERROR -96)
- CAUSE
The directory UFID entry for this file is probably invalid.
- ACTION
Run FSCHECK on the system.
- 97
- MESSAGE
Files in the specified file domain must remain in the MPE namespace. (FILE SYSTEM ERROR -97)
- CAUSE
An attempt was made to place a file outside the MPE namespace in a file domain that only supports the MPE namespace.
- ACTION
Do not attempt to give this file a name outside the MPE namespace.
- 100
- MESSAGE
The name syntax that was specified is invalid. (FILE SYSTEM ERROR -100)
- CAUSE
An invalid name syntax was specified.
- ACTION
Consult the Intrinsics Manual for valid syntax values.
- 101
- MESSAGE
A system file name was specified that was not known to the system. (FILE SYSTEM ERROR -101)
- CAUSE
An invalid $xxxx name was specified.
- ACTION
Consult the Intrinsics Manual for valid system file names.
- 102
- MESSAGE
An invalid character was found in an MPE syntax name. (FILE SYSTEM ERROR -102)
- CAUSE
An invalid MPE name was specified.
- ACTION
Make sure that the name contains only alphanumerics, . , /, and :.
- 103
- MESSAGE
A wildcard character was found in the name, and it was not allowed. (FILE SYSTEM ERROR -103)
- CAUSE
A wildcard character was present in the name when it was not allowed.
- ACTION
Remove wildcard characters from the name.
- 104
- MESSAGE
A back-referenced file specification is not allowed here. (FILE SYSTEM ERROR -104)
- CAUSE
A leading * was found in the name when it was not allowed.
- ACTION
Do not attempt to backreference the file to a file equation.
- 105
- MESSAGE
System files are not allowed to be specified here. (FILE SYSTEM ERROR -105)
- CAUSE
A system file was specified when it was not allowed.
- ACTION
Do not attempt to specify a system file.
- 106
- MESSAGE
A remote environment specification is not allowed here. (FILE SYSTEM ERROR -106)
- CAUSE
A remote environment was specified when it was not allowed.
- ACTION
Do not attempt to specify a remote environment.
- 107
- MESSAGE
An invalid usage of a character class was attempted. (FILE SYSTEM ERROR -107)
- CAUSE
A character class specification was done improperly.
- ACTION
Refer to either the Intrinsics Manual or the Commands Reference Manual for information on properly specifying a character class.
- 108
- MESSAGE
The name specified is missing the file name component. (FILE SYSTEM ERROR -108)
- CAUSE
The file name component of a name was not specified.
- ACTION
Make sure to specify the file name of the file.
- 109
- MESSAGE
The file name did not start with an alphabetic character. (FILE SYSTEM ERROR -109)
- CAUSE
An illegal file name was specified.
- ACTION
Make sure the name specified conforms to the specified syntax rules.
- 110
- MESSAGE
The file name specified is exceeds the maximum legal length. (FILE SYSTEM ERROR -110)
- CAUSE
The file name is too long.
- ACTION
Make sure the name conforms to the specified syntax rules.
- 111
- MESSAGE
The lockword in the backreferenced file name is illegal. (FILE SYSTEM ERROR -111)
- CAUSE
The lockword in the backreferenced file name is illegal.
- ACTION
Specify a legal lockword.
- 112
- MESSAGE
Specifying a lockword in a wildcarded file name is illegal. (FILE SYSTEM -112)
- CAUSE
Specifying a lockword in a wildcarded file name is illegal.
- ACTION
Do not specify a lockword in a wildcarded file name.
- 113
- MESSAGE
The lockword specification is missing. (FILE SYSTEM ERROR -113)
- CAUSE
The lockword specification is missing.
- ACTION
Supply a lockword.
- 114
- MESSAGE
The lockword specified did not start with an alphabetic character. (FILE SYSTEM ERROR -114)
- CAUSE
An illegal lockword was specified.
- ACTION
Specify a legal lockword.
- 115
- MESSAGE
The lockword specified exceeds the maximum legal length. (FILE SYSTEM ERROR -115)
- CAUSE
The lockword is too long.
- ACTION
Specify a legal lockword.
- 116
- MESSAGE
The group name is missing. (FILE SYSTEM ERROR -116)
- CAUSE
The group name is missing from the specified name.
- ACTION
Supply a group name, or remove the trailing period.
- 117
- MESSAGE
The group name provided did not start with an alphabetic character. (FILE SYSTEM ERROR -117)
- CAUSE
An illegal group name was specified.
- ACTION
Supply a legal group name.
- 118
- MESSAGE
The group name specified exceeds the maximum legal length. (FILE SYSTEM ERROR -118)
- CAUSE
The group name is too long.
- ACTION
Supply a legal group name.
- 119
- MESSAGE
The account name is missing. (FILE SYSTEM ERROR -119)
- CAUSE
The account name is missing.
- ACTION
Supply an account name, or remove the trailing period.
- 120
- MESSAGE
The account name specified did not start with an alphabetic character. (FILE SYSTEM ERROR -120)
- CAUSE
An illegal account name was specified.
- ACTION
Supply a legal account name.
- 121
- MESSAGE
The account name specified exceeds the maximum legal length. (FILE SYSTEM ERROR -121)
- CAUSE
An illegal account name was specified.
- ACTION
Supply a legal account name.
- 122
- MESSAGE
The remote environment specification is invalid. (FILE SYSTEM ERROR -122)
- CAUSE
The remote environment specification is invalid.
- ACTION
Supply a legal remote environment.
- 123
- MESSAGE
NS3000 is not present on the system. (FILE SYSTEM ERROR -123)
- CAUSE
NS3000 has not been installed on the system.
- ACTION
Install NS3000, or do not attempt a remote file specification.
- 124
- MESSAGE
The remote environment specification is missing. (FILE SYSTEM ERROR -124)
- CAUSE
The remote environment specification is missing.
- ACTION
Supply a remote environment, or remove the trailing colon.
- 125
- MESSAGE
The remote environment exceeded the maximum legal length. (FILE SYSTEM ERROR -125)
- CAUSE
The remote environment specification was too long.
- ACTION
Supply a legal remote envirionment.
- 126
- MESSAGE
A component of an HFS path exceeds the maximum legal length. (FILE SYSTEM ERROR -126)
- CAUSE
A HFS path component is too long.
- ACTION
Supply legal names in each component of the HFS pathname.
- 127
- MESSAGE
The HFS path specification exceeds the maximum legal length. (FILE SYSTEM ERROR (-127)
- CAUSE
The HFS path name is too long.
- ACTION
Change the CWD to a lower point in the path name and use relative naming to specify the path name.
- 128
- MESSAGE
The HFS path name exceeded the number of levels supported. (FILE SYSTEM ERROR -128)
- CAUSE
There are too many directory levels in the path name.
- ACTION
File an SR.
- 129
- MESSAGE
A component of the HFS path name started with a hyphen (-). (FILE SYSTEM ERROR -129)
- CAUSE
An invalid HFS component name was specified.
- ACTION
Supply legal HFS component names.
- 130
- MESSAGE
The HFS path name specified began with two slashes (//). (FILE SYSTEM ERROR -130)
- CAUSE
The path name began with two slashes.
- ACTION
Use only one leading slash.
- 131
- MESSAGE
Lower case characters were detected and are not allowed. (FILE SYSTEM ERROR -131)
- CAUSE
While parsing the name, the system was not allowing lower case characters in this case and it found some.
- ACTION
Upshift the lowercase characters.
- 132
- MESSAGE
The wildcarded name provided may match an incorrect syntax. (FILE SYSTEM WARNING 132)
- CAUSE
Wildcard character expansion may match names not in the specified syntax.
- ACTION
No action necessary.
- 133
- MESSAGE
The syntax of the specified name cannot be determined. (FILE SYSTEM ERROR -133)
- CAUSE
The system could not determine the syntax of the name specified.
- ACTION
Specify a syntax parameter value, or express the name more clearly.
- 134
- MESSAGE
A lockword specification was attempted, but it is not allowed. (FILE SYSTEM ERROR -134)
- CAUSE
A lockword was present, but the system does not allow them in this case.
- ACTION
Remove the lockword specification.
- 135
- MESSAGE
An illegal attempt was made to escape to HFS syntax from an MPE only syntax name. (FILE SYSTEM ERROR -135)
- CAUSE
The name illegally started with either a dot (.) or a slash (/).
- ACTION
Use either MPE escaped syntax, or HFS syntax.
- 136
- MESSAGE
An illegal character was found in the HFS path name. (FILE SYSTEM ERROR -136)
- CAUSE
An invalid character was in the HFS path name.
- ACTION
Remove the invalid character from the path name.
- 137
- MESSAGE
Incompatible version of the file.
- CAUSE
An error occurred while trying to access afile label extension.
- ACTION
Call your HP Support Representative.
- 140
- MESSAGE
Internal ACD corruption (equivalent to HOP_INTERNAL_ACD_ERROR.)
- 165
- MESSAGE
Inserting a directory entry failed due to the system's directory limit.
- CAUSE
Inserting a directory entry failed because the directory size would exceed the system's limit for directory files.
- ACTION
Delete/purge some entries from the current directory or increase thedirectory limit.
- 173
- MESSAGE
The caller lacks sufficient privilege to specify this read format option. (FILE SYSTEM ERROR -173)
- CAUSE
The caller is not privileged enough to be granted the requested read format option.
- ACTION
Do not request this option, or become sufficiently privileged.
- 174
- MESSAGE
The Multiple Build Environment Facility has encountered an internal error. (FILE SYSTEM ERROR -174)
- CAUSE
An internal error was encountered by the MBE code.
- ACTION
Contact the appropriate HP personnel.
- 175
- MESSAGE
A component of the path name specified is not a directory. (FILE SYSTEM ERROR -175)
- CAUSE
One of the intermediate path name components is not a directory.
- ACTION
Correct the invalid path name component.
- 176
- MESSAGE
A name in the MPE namespace is required. (FILE SYSTEM ERROR -176)
- CAUSE
The name specified lies outside of the MPE namespace.
- ACTION
Make sure that the name provided is within the MPE namespace.
- 177
- MESSAGE
The maximum number of hard links to the file has been exceeded. (FILE SYSTEM ERROR -177)
- CAUSE
There are too many pre-existing links to this file.
- ACTION
Remove some of the existing links, or use a different file.
- 178
- MESSAGE
The user lacks the ability to purge this object. (FILE SYSTEM ERROR -178)
- CAUSE
The system security will not allow this user to purge the object.
- ACTION
Have the system manager grant the user the necessary access rights.
- 179
- MESSAGE
The user lacks the ability to create an object. (FILE SYSTEM ERROR -179)
- CAUSE
The system security will not allow this user to create the object.
- ACTION
Have the system manager grant the user the necessary access rights.
- 180
- MESSAGE
The user lacks the ability to traverse through a directory in the specified path. (FILE SYSTEM ERROR -180)
- CAUSE
The system security will not allow this user to traverse through a directory in the path.
- ACTION
Have the system manager grant the user the necessary access rights.
- 181
- MESSAGE
The read format option contained an illegal value. (FILE SYSTEM ERROR -181)
- CAUSE
The value passed in with the read format option was not in the valid range.
- ACTION
Consult the Intrinsics Manual for valid values for this item.
- 182
- MESSAGE
The length of the collating sequence table is too long. (FILE SYSTEM ERROR -182)
- CAUSE
The length of the collating sequence table is too long.
- ACTION
Reduce the size of the collating sequence table.
- 183
- MESSAGE
HOP_KSM_MISSING_KSAMPARAM: There was no ksamparam array passed in for the creation of the KSAM file. Therefore, the open of the KSAM file failed.
- CAUSE
No ksamparam array was passed in.
- ACTION
Specify the ksamparam array when openning a new KSAM file.
- 184
- MESSAGE
HOP_KSM_INVALID_KEY_LOC: An invalid key location was specified in the ksamparam array. Therefore, the open of the KSAM file failed.
- CAUSE
Either the key location specified is less than one or another key starts at the same location.
- ACTION
Change the key location so it is greater than zero and does not start at the same location as another key.
- 185
- MESSAGE
HOP_KSM_INVALID_KEY_LEN: An invalid key length was specified in the ksamparam array. Therefore, the open of the KSAM file failed.
- CAUSE
Either the key length specified is invalid for the key type or the key length combined with the starting key location would extend the particular key beyond the record length.
- ACTION
Change the key length so it is valid for the key type or reduce the key length so that the particular key does not extend beyond the record length.
- 186
- MESSAGE
HOP_KSM_INVALID_KEY_TYPE: An invalid key type was specified in the ksamparam array. Therefore, the open of the KSAM file failed.
- CAUSE
An invalid key type was specified in the ksamparam array.
- ACTION
Change the key type so that it is valid.
- 187
- MESSAGE
HOP_KSM_OUT_OF_INDEX_SPACE: The space reserved for the index area in the file is full and has reached the start of the data area.
- CAUSE
This error should never occur during the open of a file. If this error occurs, then there is some internal error in the operating system.
- ACTION
Record the parameter values passed to FOPEN or HPFOPEN. Call your HP Support Representative.
- 188
- MESSAGE
HOP_KSM_INVALID_KEY_COUNT: An invalid key count was passed in the ksamparam array. Therefore, the open of the KSAM file failed.
- CAUSE
The key count specified in the ksamparam array was not between 1 and 16.
- ACTION
Change the key count to be between 1 and 16.
- 189
- MESSAGE
HOP_KSM_ATTACH_FAILED: The call to Transaction Management (XM) to attach a file for logging failed. Therefore, the open of the KSAM file failed.
- CAUSE
An internal MPE/iX error occurred.
- ACTION
Take a memory dump and call your HP Support Representative.
- 190
- MESSAGE
HOP_KSM_UNSUPPORTED_LANGUAGE: An invalid language id was specified in the ksamparam array. Therefore, the open of the KSAM file failed.
- CAUSE
The language specified in the ksamparam array is not supported on MPE/iX.
- ACTION
Change the language to a supported language.
- 191
- MESSAGE
HOP_KSM_NLS_ERROR: NLS detected an error while verifying that the language specified in the ksamparam is supported. Therefore, the open of the KSAM file failed.
- CAUSE
An internal NLS error occurred.
- ACTION
Record the parameter values passed to FOPEN and HPFOPEN. Call your HP Support Representative.
- 192
- MESSAGE
HOP_KSM_XM_START_TRAN_FAILED: Transaction Management (XM) detected an error while starting a transaction. Therefore, the open of the KSAM file failed.
- CAUSE
An internal error occurred in MPE/iX.
- ACTION
Record the parameter values passed to FOPEN and HPFOPEN. Call your HP Support Representative.
- 193
- MESSAGE
HOP_KSM_XM_END_TRAN_FAILED: Transaction Management (XM) detected an error while ending a transaction.
- CAUSE
An internal error occurred in MPE/iX.
- ACTION
Record the parameter values passed to FOPEN and HPFOPEN. Call your HP Support Representative.
- 194
- MESSAGE
HOP_KSM_XM_TRAVERSE_TREE_ERROR: There was an error in the index pages detected while searching for the lowest primary key. Therefore, the open of the KSAM file failed.
- CAUSE
The KSAM file is corrupted.
- ACTION
Close the KSAM file, store it to tape, and call your HP Support Representative.
- 195
- MESSAGE
HOP_KSM_INDEX_ERROR: There was an error in the index header for the index blocks. Therefore, the open of the KSAM file failed.
- CAUSE
The KSAM file is corrupted.
- ACTION
Close the KSAM file, store it to tape, and call your HP Support Representative.
- 196
- MESSAGE
HOP_KSM_INVALID_DATA_PTR_CALCULATED: The calculation of the pointed to, lowest primary key, resulted in an invalid offset into the file. Therefore, the open of the KSAM file failed.
- CAUSE
The KSAM file is corrupted.
- ACTION
Close the KSAM file, store it to tape, and call your HP Support Representative.
- 198
- MESSAGE
An item is present in the parameters passed to HPFOPEN, but the associated item number is missing; the item was ignored. (FILE OPEN WARNING 198)
- CAUSE
An item number is missing in the parameters passed to HPFOPEN. Usually, this is caused by two commas in a row ",,".
- ACTION
Always specify an item number when passing an item to HPFOPEN.
- 199
- MESSAGE
An ITEMNUMBER is present in the parameters passed to HPFOPEN, but the associated item is missing; the ITEMNUMBER was ignored. (FILE OPEN WARNING 199)
- CAUSE
The item associated with an item number was not passed to HPFOPEN. The usual cause is two commas in a row ",,"."
- ACTION
Except for item number zero, you must specify an item with all item numbers.
CIERR 200 - 399
- 200
- MESSAGE
The DOMAIN OPTION (item# 3) does not match the DOMAIN of the file, or two specified options conflict regarding the file's DOMAIN. (FILE OPEN WARNING 200).
- CAUSE
Usually, this is caused by specifing a NEW domain for a non-sharable device or by specifying two conflicting domains at the same time.
- ACTION
In general, this warning can be ignored. It's purpose is to indicate that HPFOPEN had to override one or more domain specifications.
- 201
- MESSAGE
Two or more ITEMNUMS conflict. (FILE OPEN WARNING 201)
- CAUSE
This is usually caused by specifying a device name or device class and a volume name or volume class. Or, by specifying the same item number more than once.
- ACTION
Do not specify the same item number more than once. For the options that can be specified by more that one item number use only of the item numbers.
- 202
- MESSAGE
The FORMALDESIGNATOR OPTION (item# 2) is invalid, or a bounds violation occurred on this option. (FILE OPEN ERROR 202)
- CAUSE
The formal designator contains invalid characters or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the formal designator correctly.
- 203
- MESSAGE
The FILE DOMAIN OPTION (item# 3) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 203)
- CAUSE
The domain is not one of the valid domain values or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the domain correctly.
- 204
- MESSAGE
The ASCII/BINARY OPTION (item# 53) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 204)
- CAUSE
The data type is not one of the valid data types or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the data type correctly.
- 205
- MESSAGE
The RECORD FORMAT OPTION (item# 6) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 205)
- CAUSE
The record format is not one of the valid record formats or the variable passed to the file is not accessible by the caller.
- ACTION
Specify the record format correctly.
- 206
- MESSAGE
The CARRIAGE CONTROL OPTION (item# 7) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 206)
- CAUSE
The carriage control is not a valid carriage control or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the carriage control correctly.
- 207
- MESSAGE
The LABELED TAPE LABEL OPTION (item# 8) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 207)
- CAUSE
The tape label is not specified correctly or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the tape label correctly.
- 208
- MESSAGE
The DISALLOW FILE EQUATION OPTION (item# 9) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 208)
- CAUSE
The DISALLOW FILE EQUATION OPTION is not specified correctly or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the DISALLOW FILE EQUATION OPTION correctly.
- 209
- MESSAGE
The FILE TYPE OPTION (item# 10) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 209)
- CAUSE
The file type is not one of the valid file types or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the file type correctly.
- 210
- MESSAGE
The ACCESS TYPE OPTION (item# 11) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 210)
- CAUSE
The access type is not one of the valid access types or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the access type correctly.
- 211
- MESSAGE
The DYNAMIC LOCKING OPTION (item# 12) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 211)
- CAUSE
An INVALID DYNAMIC LOCKING option was specified or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the DYNAMIC LOCKING OPTION correctly.
- 212
- MESSAGE
The EXCLUSIVE OPTION (item# 13) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 212)
- CAUSE
The EXCLUSIVE OPTION specified is not a valid exclusive option or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the EXCLUSIVE OPTION correctly.
- 213
- MESSAGE
The MULTIRECORD OPTION (item# 15) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 213)
- CAUSE
The MULTI-RECORD OPTION was not specified correctly or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the MULTI-RECORD OPTION correctly.
- 214
- MESSAGE
The MULTIACCESS OPTION (item# 14) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 214)
- CAUSE
The MULTI-ACCESS OPTION was not specified correctly or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the MULTI-ACCESS OPTION correctly.
- 215
- MESSAGE
The NOWAIT I/O OPTION (item# 16) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 215)
- CAUSE
The NOWAIT I/O OPTION was not specified correctly or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the NOWAIT I/O OPTION correctly.
- 216
- MESSAGE
The COPY MODE OPTION (item# 17) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 216)
- CAUSE
The COPY MODE OPTION was not specified correctly or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the COPY MODE OPTION correctly.
- 217
- MESSAGE
The DESIGNATOR OPTION (item# 5) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 217)
- CAUSE
The specified designator is not one of the valid designator types or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify a valid designator.
- 218
- MESSAGE
Bounds violation occurred on either the SHORT MAPPED OPTION (item# 18), or on the LONG MAPPED OPTION (item# 21). (FILE OPEN ERROR 218)
- CAUSE
The pointer variable passed to HPFOPEN is not accessible by the caller.
- ACTION
Use only program-local variables when calling HPFOPEN.
- 219
- MESSAGE
The RECORD SIZE OPTION (item# 19) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 219)
- CAUSE
The specified record size is not correct or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify a valid record size.
- 220
- MESSAGE
The DEVICE NAME OPTION (item# 20) is not valid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 220)
- CAUSE
The specified device name contains one of the following errors: invalid characters, missing delimiters, invalid length, or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify a valid device name using valid delimiters.
- 221
- MESSAGE
The VOLUME CLASS OPTION (item# 22) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 221)
- CAUSE
The specified volume class name contains one or the following errors: invalid characters, missing delimiters, invalid length, or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify a valid volume class name using valid delimiters.
- 222
- MESSAGE
The VOLUME NAME OPTION (item# 23) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 222)
- CAUSE
The specified volume name contains one of the following errors: invalid characters, missing delimiters, invalid length or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify a valid volume name using valid delimiters.
- 223
- MESSAGE
The TAPE DENSITY OPTION (item# 24) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 223)
- CAUSE
The specified tape density is not a valid density or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify the tape density correctly.
- 224
- MESSAGE
The PRINTER ENVIRONMENT OPTION (item# 25) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 224)
- CAUSE
The specified environment file name contains one of the following errors: invalid characters, missing delimiters, invalid length or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify a valid environment file name using valid delimiters.
- 225
- MESSAGE
The REMOTE ENVIRONMENT OPTION (item# 26) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 225)
- CAUSE
The specified remote environment name contains one of the following errors: invalid characters, missing delimiters, invalid length of the variable passed to the file system is not accessible by the caller.
- ACTION
Specify a valid remote environment name using valid delimiters.
- 226
- MESSAGE
The OUTPUT PRIORITY OPTION (item# 27) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 226)
- CAUSE
The specified printer priority is not a valid priority or the variable passed to the file system is not accessible by the caller.
- ACTION
Specify a valid printer priority.
- 227
- MESSAGE
The SPOOLED MESSAGE OPTION (item# 28) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 227)
- 229
- MESSAGE
The LABELED TAPE TYPE OPTION (item# 30) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 229)
- 230
- MESSAGE
The LABELED TAPE EXPIRATION OPTION (item# 31) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 230)
- 231
- MESSAGE
The LABELED TAPE SEQUENCE OPTION (item# 32) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 231)
- 232
- MESSAGE
The USER LABELS OPTION (item# 33) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 232)
- 233
- MESSAGE
The SPOOLER COPIES OPTION (item# 34) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 233)
- 234
- MESSAGE
The FILESIZE OPTION (item# 35) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 234)
- 235
- MESSAGE
The INITIAL ALLOCATION OPTION (item# 36) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 235)
- 236
- MESSAGE
The FILECODE OPTION (item# 37) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 236)
- 238
- MESSAGE
The WILL-ACCESS OPTION (item# 39) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 238)
- 239
- MESSAGE
The BLOCK FACTOR OPTION (item# 40) is not valid, or a bounds violation occurred on the option. (FILE OPEN ERROR 239)
- 240
- MESSAGE
The FILE NAME SYNTAX OPTION (item# 41) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 240)
- 241
- MESSAGE
The DEVICE CLASS OPTION (item# 42) is either invalid, missing delimiters, or a bounds violation occurred on this option. (FILE OPEN ERROR 241)
- 242
- MESSAGE
A file equation is required, but a file equation for the file does not exist. (FILE OPEN ERROR 242)
- 243
- MESSAGE
An invalid (unsupported) ITEMNUMBER was passed to HPFOPEN. (FILE OPEN ERROR 243)
- 244
- MESSAGE
A bounds violation occurred on the pointer passed with the LONG MAPPED OPTION (item# 21). (FILE OPEN ERROR 244)
- 245
- MESSAGE
The FORMALDESIGNATOR OPTION (item# 2) does not represent a valid MPE/iX file name. (FILE OPEN ERROR 245)
- 246
- MESSAGE
Specifying REMOTE ACCESS with these options is not allowed. (FILE OPEN ERROR 246)
- 247
- MESSAGE
The file does not exist in specified domain; the file was not found. (FILE OPEN ERROR 247)
- 248
- MESSAGE
Access to this file is denied for the specified file access; a security violation occurred. (FILE OPEN ERROR 248)
- 249
- MESSAGE
This file may not be opened with these options and the current user's privilege level; a priveleged file violation occurred. (FILE OPEN ERROR 249)
- 250
- MESSAGE
The number of files opened for this process exceeds the maximum available. (FILE OPEN ERROR 250)
- 251
- MESSAGE
An error occurred in FDEVICECONTROL while processing the specified printer environment file. (FILE SYSTEM ERROR -251)
- CAUSE
A failure in the FDEVICECONTROL intrinsic.
- ACTION
File an SR.
- 252
- MESSAGE
The file may not be opened exclusively, because the file is already open. (FILE OPEN ERROR 252)
- 253
- MESSAGE
The requested functionality is not currently implemented. (FILE OPEN ERROR 253)
- 254
- MESSAGE
The file name is missing from the formal designator specification. (FILE OPEN ERROR 254)
- 255
- MESSAGE
The file name starts with a nonalphabetic character. (FILE OPEN ERROR 255)
- 256
- MESSAGE
The file name exceeds eight characters. (FILE OPEN ERROR 256)
- 257
- MESSAGE
The file name contains a nonalphanumeric character. (FILE OPEN ERROR 257)
- 258
- MESSAGE
The lockword starts with a nonalphabetic character. (FILE OPEN ERROR 258)
- 259
- MESSAGE
The lockword exceeds eight characters. (FILE OPEN ERROR 259)
- 260
- MESSAGE
The lockword contains a nonalphanumeric character. (FILE OPEN ERROR 260)
- 261
- MESSAGE
The group name is missing from formal designator specification. (FILE OPEN ERROR 261)
- 262
- MESSAGE
The group name starts with a nonalphabetic character. (FILE OPEN ERROR 262)
- 263
- MESSAGE
The group name exceeds eight characters. (FILE OPEN ERROR 263)
- 264
- MESSAGE
The group name contains a nonalphanumeric character. (FILE OPEN ERROR 264)
- 265
- MESSAGE
The account name is missing from the formal designator specification. (FILE OPEN ERROR 265)
- 266
- MESSAGE
The account name starts with a nonalphabetic character. (FILE OPEN ERROR 266)
- 267
- MESSAGE
The account name exceeds eight characters. (FILE OPEN ERROR 267)
- 268
- MESSAGE
The account name contains a nonalphanumeric character. (FILE OPEN ERROR 268)
- 269
- MESSAGE
The remote environment or node name specified within a formal designator is null. (FILE OPEN ERROR 269)
- 270
- MESSAGE
The node name or remote environment specification in the formal designator exceeds 80 characters. (FILE OPEN ERROR 270)
- 271
- MESSAGE
The volume name specified on an existing file does not match the volume restrictions for that file. (HPFOPEN ERROR 271)
- 272
- MESSAGE
The volume class specified does not match the volume restrictions for the existing file. (FILE OPEN ERROR 272)
- 273
- MESSAGE
The creation of a file failed because of a duplicate permanent file. (FILE OPEN ERROR 273)
- 274
- MESSAGE
The volume class does not reside in the volume set attached to the group in which the file is being opened. (FILE OPEN ERROR 274)
- 275
- MESSAGE
The volume name does not reside in the volume class specified. (FILE OPEN ERROR 275)
- 276
- MESSAGE
The volume name specified does not reside in the volume set attached to the group in which the file is being opened. (FILE OPEN ERROR 276)
- 277
- MESSAGE
The procedure failed to allocate a new GDPD; there are too many multi-access files opened on the system. (FILE OPEN ERROR 277)
- 278
- MESSAGE
The base of the option can not specify the option list.
- 279
- MESSAGE
This message is reserved.
- 280
- MESSAGE
Specifying the FORMALDESIGNATOR OPTION (item# 2) for this file type is invalid. (FILE OPEN ERROR 280)
- 281
- MESSAGE
Specifying the DOMAIN OPTION (item# 3) for this file type is invalid. (FILE OPEN ERROR 281)
- 282
- MESSAGE
To be provided.
- 283
- MESSAGE
Specifying the DESIGNATOR OPTION (item# 5) for this file type is invalid. (FILE OPEN ERROR 283)
- 284
- MESSAGE
Specifying the RECORD FORMAT OPTION (item# 6) for this file type is invalid. (FILE OPEN ERROR 284)
- 285
- MESSAGE
Specifying the CARRIAGE CONTROL OPTION (item# 7) for this file type is invalid. (FILE OPEN ERROR 285)
- 286
- MESSAGE
Specifying the LABELED TAPE LABEL OPTION (item# 8) for this file type is invalid. (FILE OPEN ERROR 286)
- 287
- MESSAGE
Specifying the DISALLOW FILE EQUATION OPTION (item# 9) for this file type is invalid. (FILE OPEN ERROR 287)
- 288
- MESSAGE
Specifying the FILE TYPE OPTION (item# 10) for this type of file is invalid; contact your SE. (FILE OPEN ERROR 288)
- 289
- MESSAGE
Specifying the ACCESS TYPE OPTION (item# 11) for this file type is invalid. (FILE OPEN ERROR 289)
- 290
- MESSAGE
Specifying the DYNAMIC LOCKING OPTION (item#12) for this file type is not valid. (FILE OPEN ERROR 290)
- 291
- MESSAGE
Specifying the EXCLUSIVE OPTION (item# 13) for this file type is invalid. (FILE OPEN ERROR 291)
- 292
- MESSAGE
Specifying the MULTIACCESS OPTION (item# 14) for this file type is invalid. (FILE OPEN ERROR 292)
- 293
- MESSAGE
Specifying the MULTIRECORD OPTION (item# 15) for this file type is not valid. (FILE OPEN ERROR 293)
- 294
- MESSAGE
Specifying the NOWAIT I/O OPTION (item# 16) for this file type is not valid. (FILE OPEN ERROR 294)
- 295
- MESSAGE
Specifying the COPY MODE OPTION (item# 1) for this file type is not valid. (FILE OPEN ERROR 295)
- 296
- MESSAGE
Specifying the SHORT MAPPED OPTION (item# 18) for this file type is not valid. (FILE OPEN ERROR 296)
- 297
- MESSAGE
Specifying the RECORD SIZE OPTION (item# 19) for this file type is invalid. (FILE OPEN ERROR 297)
- 298
- MESSAGE
Specifying the DEVICE NAME OPTION (item# 20) for this file type is invalid. (FILE OPEN ERROR 298)
- 299
- MESSAGE
Specifying the LONG MAPPED OPTION (item# 21) for this file type is invalid. (FILE OPEN ERROR 299)
- 300
- MESSAGE
Specifying the VOLUME CLASS OPTION (item# 22) for this file type is invalid. (FILE OPEN ERROR 300)
- 301
- MESSAGE
Specifying the VOLUME NAME OPTION (item# 23) for this file type is invalid. (FILE OPEN ERROR 301)
- 302
- MESSAGE
Specifying the DENSITY OPTION (item# 24) for this file type is invalid. (FILE OPEN ERROR 302)
- 303
- MESSAGE
Specifying the PRINTER ENVIRONMENT OPTION (item# 25) for this file type is invalid. (FILE OPEN ERROR 303)
- 304
- MESSAGE
Specifying the REMOTE ENVIRONMENT OPTION (item# 26) for this file type is invalid. (FILE OPEN ERROR 304)
- 305
- MESSAGE
Specifying the OUTPUT PRIORITY OPTION (item# 27) for this file type is invalid. (FILE OPEN ERROR 305)
- 306
- MESSAGE
Specifying the SPOOLED MESSAGE OPTION (item# 28) for this file type is invalid. (FILE OPEN ERROR 306)
- 307
- MESSAGE
Specifying the PRIVILEGED ACCESS OPTION (item# 29) for this file type is invalid. (FILE OPEN ERROR 307)
- 308
- MESSAGE
Specifying the LABELED TAPE TYPE OPTION (item# 30) for this file type is invalid. (FILE OPEN ERROR 308)
- 309
- MESSAGE
Specifying the LABELED TAPE EXPIRATION OPTION (item# 31) for this file is invalid. (FILE OPEN ERROR 309)
- 310
- MESSAGE
Specifying the LABELED TAPE SEQUENCE OPTION (item# 32) for this file type is invalid. (FILE OPEN ERROR 310)
- 311
- MESSAGE
Specifying the USER LABELS OPTION (item# 33) for this file type is invalid. (FILE OPEN ERROR 311)
- 312
- MESSAGE
Specifying the SPOOLER COPIES OPTION (item# 34) for this file type is invalid. (FILE OPEN ERROR 312)
- 313
- MESSAGE
Specifying the FILESIZE OPTION (item# 35) for this file type is invalid. (FILE OPEN ERROR 313)
- 314
- MESSAGE
Specifying the INITIAL ALLOCATION OPTION (item# 36) for this file type is invalid. (FILE OPEN ERROR 314)
- 315
- MESSAGE
Specifying the FILECODE OPTION (item# 37) for this file type is invalid. (FILE OPEN ERROR 315)
- 316
- MESSAGE
Specifying the FILE PRIVILEGE OPTION (item# 38) for this file type is invalid. (FILE OPEN ERROR 316)
- 317
- MESSAGE
Specifying the WILL ACCESS OPTION (item# 39) for this file type is invalid. (FILE OPEN ERROR 317)
- 318
- MESSAGE
Specifying the BLOCK FACTOR OPTION (item# 40) for this file type is invalid. (FILE OPEN ERROR 318)
- 319
- MESSAGE
Specifying the NAME SYNTAX OPTION (item# 41) for this file type is invalid. (FILE OPEN ERROR 319)
- 320
- MESSAGE
Specifying the DEVICE CLASS OPTION (item# 42) for this file type is invalid. (FILE OPEN ERROR 320)
- 321
- MESSAGE
Specifying the UFID OPTION (item# 43) for this file type is invalid. (FILE OPEN ERROR 321)
- 322
- MESSAGE
Specifying the NUMBUFFERS OPTION (item# 44) for this file type is invalid. (FILE OPEN ERROR 322)
- 323
- MESSAGE
Specifying the FILL CHARACTER OPTION (item# 45) for this file type is invalid. (FILE OPEN ERROR 323)
- 324
- MESSAGE
Specifying the INHIBIT BUFFERING OPTION (item# 46) for this file type is invalid. (FILE OPEN ERROR 324)
- 325
- MESSAGE
Specifying the NUMEXTENTS OPTION (item# 47) for this file type is invalid. (FILE OPEN ERROR 325)
- 326
- MESSAGE
Specifying the REVERSE VT OPTION (item# 48) for this file type is invalid. (FILE OPEN ERROR 326)
- 327
- MESSAGE
Specifying the PIN OPTION (item# 49) for this file type is invalid. (FILE OPEN ERROR 327)
- 328
- MESSAGE
Specifying the FINAL DISPOSITION OPTION (item# 50) for this file type is invalid. (FILE OPEN ERROR 328)
- 329
- MESSAGE
Specifying the PASCAL XL STRING OPTION (item# 51) for this file type is invalid. (FILE OPEN ERROR 329)
- 330
- MESSAGE
Specifying the FILE EQUATION STRING OPTION (item# 52) for this file type is invalid. (FILE OPEN ERROR 330)
- 331
- MESSAGE
Specifying the ASCII/BINARY OPTION (item# 53) for this file type is invalid. (FILE OPEN ERROR 331)
- 332
- MESSAGE
Specifying the KSAM PARMS OPTION (item# 54) for this file type is invalid. (FILE OPEN ERROR 332)
- 333
- MESSAGE
Specifying the RAW OPTION (item# 55) for this file type is invalid. (FILE OPEN ERROR 333)
- 334
- MESSAGE
Specifying the OBJECT CLASS OPTION (item# 56) for this file type is invalid. (FILE OPEN ERROR 334)
- 335
- MESSAGE
Specifying the VARIABLE ACCESS RIGHTS OPTION (item# 57) for this file type is invalid. (FILE OPEN ERROR 335)
- 336
- MESSAGE
Specifying the UNPROTECTED OPTION (item# 58) for this file type is invalid. (FILE OPEN ERROR 336)
- 337
- MESSAGE
Specifying the SYSTEM OBJECT CLASS OPTION (item# 59) for this file type is invalid. (FILE OPEN ERROR 337)
- 338
- MESSAGE
Specifying the FILE PID OPTION (item# 60) for this file type is invalid. (FILE OPEN ERROR 338)
- 339
- MESSAGE
Specifying the ACCESS RIGHTS OPTION (item# 61) for this file type is invalid. (FILE OPEN ERROR 339)
- 340
- MESSAGE
Lockword on file being referenced cannot be specified.
- CAUSE
Specifying a lockword for a file accessed as a raw or referencing a file with a lockword using POSIX name syntax is prohibited.
- ACTION
In the case of raw mode access to a file, don't specify a lockword. In the case of name syntax, use only MPE or MPE Escaped name syntax when referencing a file with a lockword.
- 343
- MESSAGE
It is illegal to specify the file close privilege option in this context. (FILE SYSTEM ERROR -343)
- CAUSE
The file close privilege option was specified in an illegal context.
- ACTION
Do not specify the file close privilege option.
- 344
- MESSAGE
It is illegal to specify the raw open option in this context. (FILE SYSTEM ERROR -344)
- CAUSE
The raw open option was specified in an illegal context.
- ACTION
Do not specify the raw open option.
- 345
- MESSAGE
The caller lacks the necessary privilege level to call the raw open option. (FILE SYSTEM ERROR -345)
- CAUSE
The caller is not privileged enough to call the raw open option.
- ACTION
Acquire the necessary privileges before calling with this option.
- 346
- MESSAGE
The value passed in with the raw open option is not valid. (FILE SYSTEM ERROR -346)
- CAUSE
A bad file label image was passed to HPFOPEN.
- ACTION
Ensure only valid file labels are passed to HPFOPEN.
- 350
- MESSAGE
The VIRTUAL ADDRESS is nil.
- 360
- MESSAGE
The GUFD PTR is nil.
- 361
- MESSAGE
Both the LONG (item# 21) and SHORT MAPPED (item# 18) OPTIONS were specified; this is a conflict. (FILE OPEN ERROR 361)
- 362
- MESSAGE
The UFID OPTION (item# 43) is invalid, or a bounds violation occurred on this option. (FILE OPEN ERROR 362)
- 363
- MESSAGE
The file could not be found because insufficient options were specified. (FILE OPEN ERROR 363)
- 364
- MESSAGE
Opening a user-mapped, variable length file for write access is not allowed. (FILE OPEN ERROR 364)
- 365
- MESSAGE
An internal inconsistency was found within the file system data structures; contact your HP Service Representative. (FILE OPEN ERROR 365)
- 366
- MESSAGE
The options specified can not be supplied to the COMPATIBILITY MODE FILE SYSTEM. (FILE OPEN ERROR 366)
- 367
- MESSAGE
A bounds violation occurred on the formal designator. (FILE OPEN ERROR 367)
- 368
- MESSAGE
The FILE TYPE OPTION in the options is not valid. (FILE OPEN ERROR 368)
- 369
- MESSAGE
The record format in the AOPTIONS is not valid. (FILE OPEN ERROR 369)
- 370
- MESSAGE
The DOMAIN is not valid. (FILE OPEN ERROR 370)
- 371
- MESSAGE
The MULTIACCESS OPTION in the AOPTIONS is not valid. (FILE OPEN ERROR 371)
- 372
- MESSAGE
The EXCLUSIVE OPTION in the AOPTIONS is not valid. (FILE OPEN ERROR 372)
- 373
- MESSAGE
The ACCESS OPTION in the AOPTIONS is not valid. (FILE OPEN ERROR 373)
- 374
- MESSAGE
The RECORD SIZE PARAMETER is not valid. (FILE OPEN ERROR 374)
- 375
- MESSAGE
A bounds violation occurred on the DEVICE parameter. (FILE OPEN ERROR 375)
- 376
- MESSAGE
A bounds violation occurred on the FORMS MESSAGE parameter. (FILE OPEN ERROR 376)
- 377
- MESSAGE
The number of USER LABELS specified is invalid. (FILE OPEN ERROR 377)
- 378
- MESSAGE
The BLOCKFACTOR parameter is out of range. (FILE OPEN ERROR 378)
- 379
- MESSAGE
The PRICOPBUFS parameter is invalid. (FILE OPEN ERROR 379)
- 380
- MESSAGE
The FILE SIZE parameter is invalid. (FILE OPEN ERROR 380)
- 381
- MESSAGE
The EXTENT parameter is invalid. (FILE OPEN ERROR 381)
- 382
- MESSAGE
The FILECODE parameter is invalid. (FILE OPEN ERROR 382)
- 383
- MESSAGE
The DEVICE NAME parameter is invalid. (FILE OPEN ERROR 383)
- 384
- MESSAGE
Missing delimiter in DEVICE STRING after device options. (FILE OPEN ERROR 384)
- 385
- MESSAGE
The LDEV is ZERO; this is not valid. (FILE OPEN ERROR 385)
- 386
- MESSAGE
The DEVICE CLASS is invalid. (FILE OPEN ERROR 386)
- 387
- MESSAGE
The DEVICE CLASS NAME exceeds eight characters in length. (FILE OPEN ERROR 387)
- 388
- MESSAGE
The DEVICE OPTIONS after the device name are invalid. (FILE OPEN ERROR 388)
- 389
- MESSAGE
The FORMS LENGTH is too large. (FILE OPEN ERROR 389)
- 390
- MESSAGE
The TAPE LABEL exceeds 16 characters. (FILE OPEN ERROR 390)
- 391
- MESSAGE
The EXPIRATION DATE for LABELED TAPES exceeds the maximum length for dates. (FILE OPEN ERROR 391)
- 392
- MESSAGE
The LABELED TAPE SEQUENCE parameter is too long. (FILE OPEN ERROR 392)
- 393
- MESSAGE
The TAPE TYPE is not one of IBM or ANS. (FILE OPEN ERROR 393)
- 394
- MESSAGE
The DELIMITER is missing in the FORMS message (after the labelled tape information). (FILE OPEN ERROR 394)
- 395
- MESSAGE
There is a comma missing in the DEVICE specification. (FILE OPEN ERROR 395)
- 396
- MESSAGE
The DENSITY OPTION is not valid. (FILE OPEN ERROR 396)
- 397
- MESSAGE
The number of buffers specified is invalid. (FILE OPEN ERROR 397)
- 398
- MESSAGE
The FILL CHARACTER OPTION (item# 45) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 398)
- 399
- MESSAGE
The INHIBIT BUFFERING OPTION (item# 46) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 399)
CIERR 400 - 699
- 400
- MESSAGE
The NUMEXTENTS OPTION (item# 47) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 400)
- 401
- MESSAGE
New files may not be opened using the UFID OPTION (item# 43) if the file has not been saved as a permanent file. (FILE OPEN ERROR 401)
- 402
- MESSAGE
File creation failed during directory insertion due to security violations. (FILE OPEN ERROR 402)
- 403
- MESSAGE
The PIN OPTION (item# 49) was specified by a caller executing at an incorrect PRIVILEGE level. (FILE OPEN ERROR 403)
- 404
- MESSAGE
The PIN parameter is invalid. (FILE OPEN ERROR 404)
- 405
- MESSAGE
The maximum BLOCK SIZE was exceeded for a file with variable length records. (FILE OPEN ERROR 405)
- 406
- MESSAGE
The file type specified in the FILE TYPE OPTION (item# 10) is not supported. (FILE OPEN ERROR 406)
- 407
- MESSAGE
No file exists at the PIN and file number specified. (FILE BESTOW ERROR 407)
- 408
- MESSAGE
Can not bestow a nonNATIVE MODE FILE. (FILE BESTOW ERROR 408)
- 409
- MESSAGE
The FROM file does not exist (is not opened). (FILE BESTOW ERROR 409)
- 410
- MESSAGE
Opening of a DIRECTORY file failed because allocation of a PLFD failed. (PROCESS CREATION ERROR 410)
- 411
- MESSAGE
The PLFD TABLE has been corrupted; contact your SE. (PROCESS CREATION ERROR 411)
- 412
- MESSAGE
Opening of a directory file failed. (PROCESS CREATION ERROR 412)
- 413
- MESSAGE
Redirection of STDIN and STDLIST is not supported. (PROCESS CREATION ERROR 413)
- 414
- MESSAGE
FCLOSE of a reserved file failed. (PROCESS CREATION ERROR 414)
- 415
- MESSAGE
Opening of $STDIN failed. (PROCESS CREATION ERROR 415)
- 416
- MESSAGE
Opening of $STDLIST failed. (PROCESS CREATION ERROR 416)
- 417
- MESSAGE
Opening of $STDERR failed. (PROCESS CREATION ERROR 417)
- 418
- MESSAGE
Opening of $PROGRAM failed. (PROCESS CREATION ERROR 418)
- 419
- MESSAGE
The file system failed to locate the FATHER'S ROOT GUFD. (PROCESS CREATION ERROR 419)
- 420
- MESSAGE
Opening the ROOT DIRECTORY file failed. (PROCESS CREATION ERROR 420)
- 421
- MESSAGE
The file system failed to locate the FATHER'S ACCOUNT directory GUFD. (PROCESS CREATION ERROR 421)
- 422
- MESSAGE
Opening of the ACCOUNT directory failed. (PROCESS CREATION ERROR 422)
- 423
- MESSAGE
The file system failed to locate the FATHER'S GROUP directory GUFD. (PROCESS CREATION ERROR 423)
- 424
- MESSAGE
Opening of the GROUP directory failed. (PROCESS CREATION ERROR 424)
- 425
- MESSAGE
The file system failed to locate the FATHER'S TEMPORARY directory GUFD. (PROCESS CREATION ERROR 425)
- 426
- MESSAGE
Opening of the TEMPORARY directory failed. (PROCESS CREATION ERROR 426)
- 427
- MESSAGE
Upon closing a reserved file and reopening the system file, the file number returned from the OPEN operation does not match the reserved file number. (PROCESS CREATION ERROR 427)
- 428
- MESSAGE
The FATHER'S directory file is not a NATIVE MODE file. (PROCESS CREATION ERROR 428)
- 429
- MESSAGE
Dynamic LOCKING was specified, yet the previous OPEN of the file did not specify dynamic LOCKING. (FILE OPEN ERROR 429)
- 430
- MESSAGE
Dynamic LOCKING was specified on a previous OPEN of this file, and dynamic LOCKING was not specified on this call to HPFOPEN. (FILE OPEN ERROR 430)
- 431
- MESSAGE
The FINAL DISPOSITION OPTION (item# 50) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 431)
- 432
- MESSAGE
The file name specified begins with a dollar sign ('$') and is not a valid standard file name. (FILE OPEN ERROR 432)
- 433
- MESSAGE
A back-referenced file equation does not exist. (FILE OPEN ERROR 433)
- 434
- MESSAGE
The specified syntax option is not currently implemented. (FILE OPEN ERROR 434)
- 435
- MESSAGE
The switch to COMPATIBILITY MODE FOPEN failed; contact your SE. (FILE OPEN ERROR 435)
- 436
- MESSAGE
There is an invalid character in the device string. (FILE OPEN ERROR 436)
- 437
- MESSAGE
$OLDPASS was not passed in for a file. (FILE OPEN ERROR 437)
- 438
- MESSAGE
The COMPATIBILITY MODE AFT index does not match the NATIVE MODE PLFD index, implying the use of an AFT without going through the standard file open mechanism. (FILE OPEN ERROR 438)
- 439
- MESSAGE
The record format specified is not compatible with the device type or file type specified. (FILE OPEN ERROR 439)
- 440
- MESSAGE
The entry point specified is not valid. (FILE OPEN ERROR 440)
- 441
- MESSAGE
The creation of the COMPATIBILITY MODE disk file failed. (FILE OPEN ERROR 441)
- 442
- MESSAGE
The file type field of the FOPTIONS does not contain a valid file type. (FILE OPEN ERROR 442)
- 443
- MESSAGE
The file system is unable to obtain the COMPATIBILITY MODE information for a COMPATIBILITY MODE file type. (FILE OPEN ERROR 443)
- 444
- MESSAGE
A file access rights entry does not exist for the specified file. (FILE ACCESS RIGHTS ERROR 444)
- 445
- MESSAGE
No more file entries can be added to the FILE ACCESS RIGHTS TABLE. (FILE ACCESS RIGHTS ERROR 445)
- 446
- MESSAGE
The creation of the FILE ACCESS RIGHTS TABLE failed. (FILE ACCESS RIGHTS ERROR 446)
- 447
- MESSAGE
The FILE EQUATION STRING OPTION (item# 52) contains an invalid character. (FILE OPEN ERROR 447)
- 448
- MESSAGE
The FILE EQUATION STRING OPTION (item# 52) is either inaccessible at the caller's privilege level (bounds violation) or is missing a delimiter. (FILE OPEN ERROR 448)
- 449
- MESSAGE
The FILE EQUATION STRING option (item# 52) is not in a valid file equation form. (FILE OPEN ERROR 449)
- 450
- MESSAGE
There is an invalid character in FILE EQUATION STRING OPTION (item# 52). (FILE OPEN ERROR 450)
- 451
- MESSAGE
The TEMPORARY FILE specified does not exist; the file was not found. (FILE OPEN ERROR 451)
- 452
- MESSAGE
Both READ and WRITE must be specified as either NOWAIT or WAIT for this type of file. (FILE OPEN ERROR 452)
- 453
- MESSAGE
The group specified does not exist in the account; the group was not found. FILE OPEN ERROR 453)
- 454
- MESSAGE
The account specified does not exist on the system; the account was not found. (FILE OPEN ERROR 454)
- 455
- MESSAGE
The PASCAL XL STRING OPTION (item# 51) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 455)
- 456
- MESSAGE
The file could not be opened because the file is being restored or stored, the file is already open, or write access is not allowed because the file is already open in a way which does not allow subsequent writers. (FILE OPEN ERROR 456)
- 457
- MESSAGE
An unknown error was returned from STORAGE MANAGEMENT. (FILE OPEN ERROR 457)
- 458
- MESSAGE
There is no more disk space left on the device; out of disk space. (FILE OPEN ERROR 458)
- 459
- MESSAGE
The specified extent size is not valid. (FILE OPEN ERROR 459)
- 460
- MESSAGE
A system error has occurred and was backed out with no system damage. (FILE OPEN ERROR 460)
- CAUSE
An ABORTIO occurred while trying to FOPEN a configured, but non-existent device.
- ACTION
Either add the device or use another.
- 461
- MESSAGE
The maximum number of files for the operating system has been exceeded. (FILE OPEN ERROR 461)
- 462
- MESSAGE
The MAPPING OPTIONS for the file are not correct. (FILE OPEN ERROR 462)
- 463
- MESSAGE
A privileged file code violation occurred. (FILE OPEN ERROR 463)
- 464
- MESSAGE
The file's privilege level exceeds the caller's access privilege level. (FILE OPEN ERROR 464)
- 465
- MESSAGE
The access privilege level exceeds the caller's privilege level. (FILE OPEN ERROR 465)
- 466
- MESSAGE
EXECUTE access was specified by a nonprivileged caller. (FILE OPEN ERROR 466)
- 467
- MESSAGE
NOWAIT I/O was requested by a nonprivileged caller. (FILE OPEN ERROR 467)
- 468
- MESSAGE
The file size exceeds the maximum file size for this type of file. Current limits are 128GB for STD fixed and KSAM64 files, 2GB for byte stream files, and 4GB for all other files. (FILE OPEN ERROR 468)
- 469
- MESSAGE
The specified LOCKWORD does not match the LOCKWORD associated with the file; this is a LOCKWORD violation. (FILE OPEN ERROR 469)
- 470
- MESSAGE
PRIVILEGE violation occurred. (FILE OPEN ERROR 470)
- 471
- MESSAGE
A BOUNDS violation occurred on the status parameter. (FILE OPEN ERROR 471)
- 472
- MESSAGE
A BOUNDS violation occurred on the file number parameter. (FILE OPEN ERROR 472)
- 473
- MESSAGE
The file number for "GET THE PLABEL" for a message file is invalid.
- 474
- MESSAGE
No PLABEL was found; contact your HP Service Representative.
- 475
- MESSAGE
The RAW OPTION (item# 55) was specified, but the caller was not executing at the required PRIVILEGE level to use this privileged feature. (FILE OPEN ERROR 475)
- 476
- MESSAGE
A BOUNDS violation occurred on the RAW OPTION (item# 55). (FILE OPEN ERROR 476)
- 477
- MESSAGE
The version number in the file label passed with the RAW OPTION (item# 55) is not correct for this version of the fsle System. (FILE OPEN ERROR 477)
- 478
- MESSAGE
The file label passed with the RAW OPTION (item# 55) is not a valid file label. (FILE OPEN ERROR 478)
- 479
- MESSAGE
The CREATE domain can not be used with the RAW OPTION (item# 55). (FILE OPEN ERROR 479)
- 480
- MESSAGE
The PERMANENT, TEMPORARY, or OLD domains can not be used with the RAW OPTION (item# 55). (FILE OPEN ERROR 480)
- 481
- MESSAGE
The system-defined file $NULL can not be opened for user-mapped access. (FILE OPEN ERROR 481)
- 482
- MESSAGE
The specified environment file could not be opened. (FILE SYSTEM ERROR -482)
- CAUSE
The open of the specified environment file failed.
- ACTION
Ensure that the environment file is made accessible.
- 483
- MESSAGE
The specified environment file is not a valid printer environment file. (FILE SYSTEM ERROR -483)
- CAUSE
The environment file is not valid.
- ACTION
Check the file code and record size.
- 484
- MESSAGE
The specified environment file has not been compiled. (FILE SYSTEM ERROR -484)
- CAUSE
An uncompiled environment file has been specified.
- ACTION
Compile the specified environment file.
- 485
- MESSAGE
The header record in the specified environment file is not valid. (FILE SYSTEM ERROR -485)
- CAUSE
The environment file is probably corrupted.
- ACTION
Replace the environment file.
- 486
- MESSAGE
An error occurred while reading the specified environment file. (FILE SYSTEM ERROR -486)
- CAUSE
An error occurred while reading the environment file.
- ACTION
Copy the environment file to another file and retry the operation.
- 487
- MESSAGE
An error occurred while closing the specified environment file. (FILE SYSTEM ERROR -487)
- CAUSE
An error occurred while closing the environment file.
- ACTION
No action is necessary.
- 488
- MESSAGE
Opening this file by UFID is prohibited.
- CAUSE
An attempt was made to open by ufid a file whose parent is a directory in the hierarchical file system (HFS) or a file which is a HFS directory itself. This is prohibited to non-system code software.
- ACTION
Either establist the calling software as system code or do not attempt open by ufid on such files.
- 490
- MESSAGE
The SHORT MAPPED file space used by the process exceeds the maximum allowed per process. (FILE OPEN ERROR 490)
- 491
- MESSAGE
The OBJECT CLASS OPTION (item# 56) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 491)
- 492
- MESSAGE
The VOLUME NAME specified does not exist in the volume set associated with the file's group. (FILE OPEN ERROR 492)
- 493
- MESSAGE
A VOLUME MANAGEMENT error occurred. (FILE OPEN ERROR 493)
- 494
- MESSAGE
The VOLUME SET associated with the file's group does not exist. (FILE OPEN ERROR 494)
- 495
- MESSAGE
The VOLUME CLASS does not exist in the volume set. (FILE OPEN ERROR 495)
- 496
- MESSAGE
The specified VOLUME CLASS is not mounted. (FILE OPEN ERROR 496)
- 497
- MESSAGE
The specified VOLUME is not MOUNTED. (FILE OPEN ERROR 497)
- 498
- MESSAGE
The specified VOLUME is not defined in the group's volume set. (FILE OPEN ERROR 498)
- 499
- MESSAGE
The VOLUME SPECIFICATION is not valid; check the VOLUME CLASS OPTION (item# 22) and/or the VOLUME NAME OPTION (item# 23). (FILE OPEN ERROR 499)
- 500
- MESSAGE
A DIRECTORY SERVICES ERROR occurred. (FILE OPEN ERROR 500)
- 501
- MESSAGE
The caller lacks the SAVE FILE (SF) capability. (FILE OPEN ERROR 501)
- 502
- MESSAGE
An invalid PARAMETER has been detected. This error may also occur on unimplemented parameter values. (FILE OPEN ERROR 502)
- 503
- MESSAGE
The PRIVILEGED ACCESS OPTION (item# 29) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 503)
- 504
- MESSAGE
The USER NAME does not exist in the directory. (FILE OPEN ERROR 504)
- 505
- MESSAGE
The VSD does not exist.
- 506
- MESSAGE
You do not have SAVE ACCESS for the specified GROUP. (FILE OPEN ERROR 506)
- 507
- MESSAGE
You do not have SAVE ACCESS for the specified account. (FILE OPEN ERROR 507)
- 508
- MESSAGE
The request would exceed the permanent file space limit for the specified group. (FILE OPEN ERROR 508)
- 509
- MESSAGE
The request would exceed the permanent file space limit for the specified account. (FILE OPEN ERROR 509)
- 510
- MESSAGE
The FILE PRIVILEGE OPTION (item# 38) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 510)
- 511
- MESSAGE
The volume set specified is closed; the file can not be opened on the volume set at this time. (FILE OPEN ERROR 511)
- 512
- MESSAGE
The VARIABLE ACCESS RIGHTS OPTION (item# 57) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 512)
- 513
- MESSAGE
The specified device name represents a sharable device. The DEVICE NAME OPTION (item# 20) may be used to specify nonsharable devices only. (FILE OPEN ERROR 513)
- 514
- MESSAGE
The specified device class represents a sharable device. The DEVICE CLASS OPTION (item# 42) may be used to specify nonsharable devices only. (FILE OPEN ERROR 514)
- 515
- MESSAGE
The UNPROTECTED OPTION (item# 58) was specified, but the caller was not at the required privilege level to use this privileged option. (FILE OPEN ERROR 515)
- 516
- MESSAGE
The UNPROTECTED OPTION (item# 58) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 516)
- 517
- MESSAGE
The UNPROTECTED OPTION (item# 58) was specified, yet the previous open of the file did not specify the UNPROTECTED OPTION. (FILE OPEN ERROR 517)
- 518
- MESSAGE
The UNPROTECTED OPTION (item# 58) was specified on a previous open of this file, but the option was not specified by the current accessor of the file. (FILE OPEN ERROR 518)
- 519
- MESSAGE
The PRIVILEGED ACCESS OPTION (item# 29) was specified for an unprotected file, and the specified access privilege level is greater than level 1. This is not allowed for unprotected files. (FILE OPEN ERROR 519)
- 520
- MESSAGE
The SYSTEM OBJECT CLASS OPTION (item# 59) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 520)
- 521
- MESSAGE
Both the OBJECT CLASS OPTION (item# 56) and SYSTEM OBJECT CLASS OPTION (item# 59) were specified; this is a conflict. (FILE OPEN ERROR 521)
- 522
- MESSAGE
The file size is greater than 4 megabytes for a short mapped file. (FILE OPEN ERROR 522)
- 523
- MESSAGE
The COMPATIBILITY MODE file could not be created. (FILE OPEN ERROR 523)
- 524
- MESSAGE
Mountable volumes are not enabled. (FILE OPEN ERROR 524)
- 525
- MESSAGE
The operator denied access to the private volume; the file could not be OPENED. (FILE OPEN ERROR 525)
- 526
- MESSAGE
A CLOSE is pending on the volume set; the file can not be OPENED. (FILE OPEN ERROR 526)
- 527
- MESSAGE
A sharable device specification was expected, but a nonsharable device was specified. (File Open error 527)
- 528
- MESSAGE
The file system is unable to START a transaction.
- 529
- MESSAGE
The file system is unable to END a transaction.
- 530
- MESSAGE
The VARIABLE ACCESS RIGHTS OPTION (item# 57) was specified by a caller executing at an incorrect privilege level. (FILE OPEN ERROR 530)
- 531
- MESSAGE
The FILE PID OPTION (item# 60) was specified by a caller executing at an incorrect privilege level. (FILE OPEN ERROR 531)
- 532
- MESSAGE
The ACCESS RIGHTS OPTION (item# 61) was specified by a caller executing at an incorrect privilege level. (FILE OPEN ERROR 532)
- 533
- MESSAGE
The FILE PID OPTION (item# 60) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 533)
- 534
- MESSAGE
The ACCESS RIGHTS OPTION (item# 61) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 534)
- 535
- MESSAGE
A MAPPED ACCESS OPTION (item# 18 or 21) was specified along with the FILE PID OPTION (item# 60); this is not allowed. (FILE OPEN ERROR 535)
- 536
- MESSAGE
A MAPPED ACCESS OPTION (item# 18 or 21) was specified along with the VARIABLE ACCESS RIGHTS OPTION (item# 57); this is not allowed. (FILE OPEN ERROR 536)
- 537
- MESSAGE
Opening a MAPPED ACCESS KSAM file for WRITE access is not allowed. (FILE OPEN ERROR 537)
- 538
- MESSAGE
Opening a MAPPED ACCESS KSAM file without COPY MODE is not allowed. (FILE OPEN ERROR 538)
- 539
- MESSAGE
A bounds violation occurred on the KSAM PARMS OPTION (item# 54). (FILE OPEN ERROR 539)
- 540
- MESSAGE
The REVERSE VT OPTION (item# 48) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 540)
- 541
- MESSAGE
The group does not exist on the volume set; the group was not found. (FILE OPEN ERROR 541)
- 542
- MESSAGE
The account does not exist on the volume set; the account was not found. (FILE OPEN ERROR 542)
- 543
- MESSAGE
Using the specified block factor and record size (plus overhead), the resultant block size is too big. (FILE OPEN ERROR 543)
- 544
- MESSAGE
The requested file mapping options conflict with the mapping options currently in effect for the file which is already open. The conflict may be in the follo wing options (item numbers): 18, 21, 57, 58, 60, 61. (FILE OPEN ERROR 544)
- 545
- MESSAGE
An unexpected trap was encountered; contact your SE. (FILE OPEN ERROR 545)
- 546
- MESSAGE
The file system can not open a file for MAPPED and WRITE access when the file is protected by TRANSACTION MANAGEMENT. (FILE OPEN ERROR 546)
- 547
- MESSAGE
The UNPROTECTED VARIABLE ACCESS RIGHTS OPTION (item# 62) was specified by a caller executing at an incorrect privilege level. (FILE OPEN ERROR 547)
- 548
- MESSAGE
The UNPROTECTED VARIABLE ACCESS RIGHTS OPTION (item# 62) is not valid, or a bounds violation occurred on this option. (FILE OPEN ERROR 548)
- 549
- MESSAGE
An error occurred while writing to the file label. (FILE OPEN ERROR 549)
- 550
- MESSAGE
A portion of the file resides on a volume which is not mounted or is not accessible by the operating system. (FILE OPEN ERROR 550)
- 551
- MESSAGE
The caller is not sufficiently privileged to request the must allocate secondary storage option. (FILE SYSTEM ERROR -551)
- CAUSE
The caller is not privileged enough to specify this option.
- ACTION
Acquire the necessary privileges prior to the operation.
- 552
- MESSAGE
The must allocate secondary storage option is not valid. (FILE SYSTEM ERROR -552)
- CAUSE
Either the value is not valid, or a bounds violation occurred.
- ACTION
Supply a legal value for this option.
- 553
- MESSAGE
An attempt was made to decrement the File Open Count Table when the count had not been incremented. (FILE SYSTEM ERROR -553)
- CAUSE
A coding error exists in the file system.
- ACTION
File an SR.
- 554
- MESSAGE
Redirecting a system file to a KSAM file is not allowed. (PROCESS ERROR 554)
- 555
- MESSAGE
The perm-to-temp final disposition was specified by a caller that is at an incorrect privilege level. (FILE OPEN ERROR 555)
- 556
- MESSAGE
An error occurred during the expansion of COMMAND INTERPRETER variables and expressions in the file name. (FILE OPEN ERROR 556)
- CAUSE
Syntax or logic error in the expressions or missing (undefined) COMMANDINTERPRETER variables.
- 557
- MESSAGE
The operating system is not in the UP state, yet a COMMAND INTERPRETER variable or expression was found in the file name. This is allowed only when MPE/iX has booted completely up. (FILE OPEN ERROR 557)
- 558
- MESSAGE
For KSAM files, the CREATE domain is allowed only when the Copy Mode option is enabled. (FILE OPEN ERROR 558)
- 560
- MESSAGE
The caller lacks sufficient privilege to specify the syntax value provided. (FILE SYSTEM ERROR -560)
- CAUSE
A privileged syntax option was specified but the caller was not privileged.
- ACTION
Acquire the necessary privileges, or specify a different syntax.
- 561
- MESSAGE
The value supplied to the file close privilege option is not valid. (FILE SYSTEM ERROR -561)
- CAUSE
A value outside the legal range of 0..3 was specified.
- ACTION
Specify only legal privilege levels.
- 563
- MESSAGE
An internal error has occurred, an invalid attempt has been made to allocate a direct access device. (FILE SYSTEM ERROR -563)
- CAUSE
An error exists in the file system.
- ACTION
File an SR.
- 568
- MESSAGE
The inherit environment option is invalid. (FILE SYSTEM ERROR -568)
- CAUSE
The value is not in the legal range, or a bounds violation occurred.
- ACTION
Specify only legal values for the inherit environment option.
- 581
- MESSAGE
The link spool file option was specified without the link device option being specified. (FILE SYSTEM ERROR -581)
- CAUSE
The link spool file option and the link device option must be specified together.
- ACTION
Specify both of these options.
- 592
- MESSAGE
The requested operation is not allowed on a read-only volume. (FILE SYSTEM ERROR -592)
- CAUSE
A write operation was requested for an object on a read-only volume.
- ACTION
Move the file to a read/write volume.
- 593
- MESSAGE
The creation of this CM file cannot be made an atomic operation. (FILE SYSTEM ERROR -593)
- CAUSE
The FMAVT SIR could not be acquired.
- ACTION
Retry the operation.
- 594
- MESSAGE
CM file opens cannot be restored to normal operation. (FILE SYSTEM ERROR -594)
- CAUSE
The FMAVT SIR could not be released.
- ACTION
Take a dump of the system and file an SR.
- 595
- MESSAGE
Files of this file type cannot be created outside the MPE namespace. (FILE SYSTEM ERROR -595)
- CAUSE
An attempt was made to create a file outside the MPE namespace that is not currently supported.
- ACTION
Use an MPE namespace name to create this file.
- 596
- MESSAGE
The specified file code is not valid in this context. (FILE SYSTEM ERROR -596)
- CAUSE
An attempt was made to assign a negative file code to a file outside an MPE group.
- ACTION
Use a positive file code, or create the file in a group.
597
- MESSAGE
NEW Domain cannot be specified for named hierarchical file system files.
- CAUSE
Specifying NEW Domain for a named file or specifying TEMPORARY Domain to open a file whose parent is a directory in the hierarchical file system (HFS) is prohibited.
- ACTION
When opening a file in the NEW Domain in a HFS directory, do not specify a filename. Files in the TEMPORARY Domain are restricted to classic MPE/iX groups.
- 598
- MESSAGE
An invalid value was specified for the read format option. (FILE SYSTEM ERROR -598)
- CAUSE
The value of the read format option is not valid.
- ACTION
Supply a valid value for the read format option.
- 599
- MESSAGE
Both the file name and the file syntax must be specified with the raw open option. (FILE SYSTEM ERROR -599)
- CAUSE
One or both of the file name and name syntax options were not specified with the raw open option.
- ACTION
Supply both the file name and the name syntax options with the raw open option.
- 600
- MESSAGE
The procedure detected the end of the file, or no error detected. (FSERR 0)
- 601
- MESSAGE
The procedure detected an illegal DB register setting. (FSERR 1)
- 602
- MESSAGE
This is an illegal capability. (FSERR 2)
- 603
- MESSAGE
The required parameter is missing. (FSERR 3)
- 604
- MESSAGE
Disk free space allocation disabled on all disks in domain (FSERR 604)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 605
- MESSAGE
DRT number > 511 (FSERR 605)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 606
- MESSAGE
Device has no available spare blocks. (FSERR 606)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 607
- MESSAGE
Unformatted or uninitialized media on device. (FSERR 607)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 608
- MESSAGE
The procedure detected an illegal parameter value. (FSERR 8)
- 609
- MESSAGE
An invalid file was specified in FOPTIONS. (FSERR 9)
- 610
- MESSAGE
This is an invalid record size specification. (FSERR 10)
- 611
- MESSAGE
The procedure detected an invalid blocksize. (FSERR 11)
- 612
- MESSAGE
Record number out of range (FSERR 612)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 613
- MESSAGE
Can't open file multi-access, out of FMAVT entries (FSERR 613)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 615
- MESSAGE
EXCEEDED THE MAXIMUM MESSAGE FILE OPENS FOR WRITE ACCESS (FSERR 615)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 616
- MESSAGE
More than 255 opens of a file occurred. (FSERR 616)
- 617
- MESSAGE
A magnetic tape runaway occurred. (FSERR 617)
- 618
- MESSAGE
The device powered up. (FSERR 618)
- 619
- MESSAGE
The forms control was reset. (FSERR 619)
- 620
- MESSAGE
This is an invalid operation. (FSERR 620)
- 621
- MESSAGE
A data parity error occurred. (FSERR 621)
- 622
- MESSAGE
A software time out occurred. (FSERR 622)
- 623
- MESSAGE
The procedure detected the end of the tape. (FSERR 623)
- 624
- MESSAGE
The unit is not ready. (FSERR 624)
- 625
- MESSAGE
There is no WRITE ring on the tape. (FSERR 625)
- 626
- MESSAGE
A transmission error occurred. (FSERR 626)
- 627
- MESSAGE
An I/O time out occurred. (FSERR 627)
- 628
- MESSAGE
A timing error on data overrun occurred. (FSERR 628)
- 629
- MESSAGE
An SIO failure occurred. (FSERR 629)
- 630
- MESSAGE
A unit failure occurred. (FSERR 630)
- 631
- MESSAGE
The procedure detected the end of the line. (FSERR 631)
- 632
- MESSAGE
A software abort occurred. (FSERR 632)
- 633
- MESSAGE
Data was lost. (FSERR 633)
- 634
- MESSAGE
The unit is not on line. (FSERR 634)
- 635
- MESSAGE
The data-set is not ready. (FSERR 635)
- 636
- MESSAGE
This is an invalid disk address. (FSERR 636)
- 637
- MESSAGE
This is an invalid memory address. (FSERR 637)
- 638
- MESSAGE
A tape parity error occurred. (FSERR 638)
- 639
- MESSAGE
Recovered tape error occurred. (FSERR 639)
- 640
- MESSAGE
The operation is inconsistent with access type. (FILE SYSTEM ERROR 640)
- 641
- MESSAGE
The operation is inconsistent with record type. (FILE SYSTEM ERROR 641)
- 642
- MESSAGE
The operation is inconsistent with device type. (FILE SYSTEM ERROR 642)
- 643
- MESSAGE
WRITE exceeds record size. (FILE SYSTEM ERROR 643)
- 644
- MESSAGE
Update at record zero. (FILE SYSTEM ERROR 644)
- 645
- MESSAGE
Privileged file violation. (FILE SYSTEM ERROR 645)
- 646
- MESSAGE
Out of disk space. (FILE SYSTEM ERROR 646)
- 647
- MESSAGE
An I/O error on file label occurred. (FILE SYSTEM ERROR 647)
- 648
- MESSAGE
An invalid operation due to multiple file access. (FILE SYSTEM ERROR 648)
- 649
- MESSAGE
This in an unimplemented function. (FILE SYSTEM ERROR 649)
- 650
- MESSAGE
This is a nonexistent account. (FILE SYSTEM ERROR 650)
- 651
- MESSAGE
This is a nonexistent group. (FILE SYSTEM ERROR 651)
- 652
- MESSAGE
This is a nonexistent permanent file. (FILE SYSTEM ERROR 652)
- 653
- MESSAGE
This is a nonexistent temporary file. (FILE SYSTEM ERROR 653)
- 654
- MESSAGE
Invalid file reference. (FILE SYSTEM ERROR 654)
- 655
- MESSAGE
Device unavailable. (FILE SYSTEM ERROR 655)
- 656
- MESSAGE
Invalid device specification. (FILE SYSTEM ERROR 656)
- 657
- MESSAGE
Out of virtual memory. (FILE SYSTEM ERROR 657)
- 658
- MESSAGE
No passed file. (FILE SYSTEM ERROR 658)
- 659
- MESSAGE
Standard label violation. (FILE SYSTEM ERROR 659)
- 660
- MESSAGE
Global RIN unavailable. (FILE SYSTEM ERROR 660)
- 661
- MESSAGE
Out of group disk space. (FILE SYSTEM ERROR 661)
- 662
- MESSAGE
Out of account disk space. (FILE SYSTEM ERROR 662)
- 663
- MESSAGE
User lacks non-sharable device capability. (FILE SYSTEM ERROR 663)
- 664
- MESSAGE
User lacks multi-RIN capability. (FILE SYSTEM ERROR 664)
- 665
- MESSAGE
Punch hopper is empty. (FILE SYSTEM ERROR 665)
- 666
- MESSAGE
Plotter limit switch reached. (FILE SYSTEM ERROR 666)
- 667
- MESSAGE
Paper tape error. (FILE SYSTEM ERROR 667)
- 668
- MESSAGE
Insufficient system resources. (FILE SYSTEM ERROR 668)
- 669
- MESSAGE
An I/O error occurred. (FILE SYSTEM ERROR 669)
- 670
- MESSAGE
An I/O error occurred while printing header/trailer. (FILE SYSTEM ERROR 670)
- 671
- MESSAGE
TOO MANY FILES OPEN (FSERR 71)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 672
- MESSAGE
INVALID FILE NUMBER (FSERR 72)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 673
- MESSAGE
BOUNDS VIOLATION (FSERR 73)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 674
- MESSAGE
No room left in stack segment for another file entry (FSERR 74)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 677
- MESSAGE
NO-WAIT I/O PENDING (FSERR 77)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 678
- MESSAGE
NO NO-WAIT I/O PENDING FOR ANY FILE (FSERR 78)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 679
- MESSAGE
NO NO-WAIT I/O PENDING FOR SPECIAL FILE (FSERR 79)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 680
- MESSAGE
SPOOFLE SIZE EXCEEDS CONFIGURATION (FSERR 80)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 681
- MESSAGE
NO "SPOOL" CLASS IN SYSTEM (FSERR 81)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 682
- MESSAGE
INSUFFICIENT SPACE FOR SPOOFLE (FSERR 82)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 683
- MESSAGE
I/O ERROR ON SPOOFLE (FSERR 83)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 684
- MESSAGE
DEVICE UNAVAILABLE FOR SPOOFLE (FSERR 84)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 685
- MESSAGE
OPERATION INCONSISTENT WITH SPOOLING (FSERR 85)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 686
- MESSAGE
Spooling internal error (FSERR 86)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 687
- MESSAGE
BAD SPOOFLE BLOCK (FSERR 87)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 688
- MESSAGE
NONEXISTENT SPOOLFILE (FSERR 88)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 689
- MESSAGE
POWER FAILURE (FSERR 89)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 690
- MESSAGE
EXCLUSIVE VIOLATION: FILE BEING ACCESSED (FSERR 90)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 691
- MESSAGE
EXCLUSIVE VIOLATION: FILE ACCESSED EXCLUSIVELY (FSERR 91)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 692
- MESSAGE
LOCKWORD VIOLATION (FSERR 92)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 693
- MESSAGE
SECURITY VIOLATION (FSERR 93)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 694
- MESSAGE
USER IS NOT CREATOR (FSERR 94)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 695
- MESSAGE
READ COMPLETED DUE TO BREAK (FSERR 95)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 696
- MESSAGE
DISC I/O ERROR (FSERR 96)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 697
- MESSAGE
NO CONTROL Y PIN (FSERR 97)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 698
- MESSAGE
READ TIME OVERFLOW (FSERR 98)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 699
- MESSAGE
BOT AND BACKSPACE TAPE (FSERR 99)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
CIERR 700 - 899
- 700
- MESSAGE
DUPLICATE PERMANENT FILE NAME (FSERR 100)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 701
- MESSAGE
DUPLICATE TEMPORARY FILE NAME (FSERR 101)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 702
- MESSAGE
I/O ERROR ON DIRECTORY (FSERR 102)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 703
- MESSAGE
PERMANENT FILE DIRECTORY OVERFLOW (FSERR 103)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 704
- MESSAGE
TEMPORARY FILE DIRECTORY OVERFLOW (FSERR 104)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 705
- MESSAGE
BAD VARIABLE BLOCK STRUCTURE (FSERR 105)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 706
- MESSAGE
EXTENT SIZE EXCEEDS MAXIMUM (FSERR 106)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 707
- MESSAGE
INSUFFICIENT SPACE FOR USER LABELS (FSERR 107)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 708
- MESSAGE
INVALID FILE LABEL (FSERR 108)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 709
- MESSAGE
INVALID CARRIAGE CONTROL (FSERR 109)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 710
- MESSAGE
ATTEMPT TO SAVE PERMANENT FILE AS TEMPORARY (FSERR 110)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 711
- MESSAGE
USER LACKS SAVE FILES (SF) CAPABILITY (FSERR 111)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 712
- MESSAGE
USER LACKS PRIVATE VOLUMES (UV) CAPABILITY (FSERR 112)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 713
- MESSAGE
VOLUME SET NOT MOUNTED - MOUNT PROBLEM (FSERR 113)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 714
- MESSAGE
VOLUME SET NOT DISMOUNTED - DISMOUNT PROBLEM (FSERR 114)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 715
- MESSAGE
ATTEMPTED RENAME ACROSS VOLUME SETS - REJECTED (FSERR 115)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 716
- MESSAGE
INVALID TAPE LABEL FOPEN PARAMETERS (FSERR 116)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 717
- MESSAGE
ATTEMPT TO WRITE ON AN UNEXPIRED TAPE FILE (FSERR 117)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 718
- MESSAGE
INVALID HEADER OR TRAILER TAPE LABEL (FSERR 118)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 719
- MESSAGE
I/O ERROR POSITIONING TAPE FOR TAPE LABELS (FSERR 119)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 720
- MESSAGE
ATTEMPT TO WRITE IBM STANDARD TAPE LABEL (FSERR 120)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 721
- MESSAGE
TAPE LABEL LOCKWORD VIOLATION (FSERR 121)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 722
- MESSAGE
Tape label table overflow (FSERR 122)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 723
- MESSAGE
END OF TAPE VOLUME SET (FSERR 123)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 724
- MESSAGE
ATTEMPT TO APPEND LABELED TAPE (FSERR 124)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 725
- MESSAGE
EXPIRATION DATE CAN'T BE LATER THAN PRECEDING FILE'S (FSERR 125)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 726
- MESSAGE
Character set number must be between 0 and 31. (FSERR 126)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 727
- MESSAGE
Form number must be between 0 and 31. (FSERR 127)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 728
- MESSAGE
Logical page number must be between 0 and 31. (FSERR 128)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 729
- MESSAGE
Vertical format number must be between 0 and 31. (FSERR 129)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 730
- MESSAGE
Number of copies must be between 1 and 32767. (FSERR 130)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 731
- MESSAGE
Number of overlays must be between 1 and 8. (FSERR 131)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 732
- MESSAGE
Page length parm must be between 12 (=3") and 68 (=17"). (FSERR 132)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 733
- MESSAGE
Picture number must be between 0 and 31. (FSERR 133)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 734
- MESSAGE
Extended capability parm must be 0 (off) or 1 (on). (FSERR 134)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 735
- MESSAGE
Unrecovered media error.(FSERR 135)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 736
- MESSAGE
USER LIMIT EXCEEDED. (FSERR 136)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 737
- MESSAGE
DEFECTIVE TRACK ON FOREIGN DISC (FSERR 137)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 738
- MESSAGE
TRACK DOES NOT EXIST ON FOREIGN DISC (FSERR 138)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 739
- MESSAGE
DELETED RECORD ON IBM DISKETTE (FSERR 139)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 740
- MESSAGE
ACCESS DENIED DUE TO CORRUPT ACD, FILE OWNER MUST REAPPLY ACD (FSERR 140)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 748
- MESSAGE
INACTIVE RIO RECORD (FSERR 148)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 749
- MESSAGE
MISSING ITEM NUMBER OR RETURN-VARIABLE (FSERR 149)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 750
- MESSAGE
INVALID ITEM NUMBER (FSERR 150)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 751
- MESSAGE
CURRENT RECORD WAS LAST RECORD WRITTEN BEFORE SYSTEM CRASHED (FSERR 151)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 752
- MESSAGE
UNRECOGNIZED KEYWORD IN FOPEN DEVICE PARAMETER (FSERR 152)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 753
- MESSAGE
EXPECTED ";" OR CARRIAGE RETURN IN DEVICE PARAMETER (FSERR 153)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 754
- MESSAGE
ENVIRONMENT FILE OPEN ERROR (FSERR 154)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 755
- MESSAGE
NOT ENVIRONMENT FILE. CHECK FILE CODE OR RECORD SIZE. (FSERR 155)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 756
- MESSAGE
ENVIRONMENT HEADER RECORD INCORRECT (FSERR 156)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 757
- MESSAGE
UNCOMPILED ENVIRONMENT FILE (FSERR 157)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 758
- MESSAGE
ERROR READING ENVIRONMENT FILE (FSERR 158)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 759
- MESSAGE
ERROR CLOSING ENVIRONMENT FILE (FSERR 159)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 760
- MESSAGE
ERROR DOING FDEVICECONTROL FROM ENVIRONMENT FILE (FSERR 160)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 761
- MESSAGE
TOO MANY PARAMETERS IN DEVICE STRING - OVERFLOW (FSERR 161)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 762
- MESSAGE
EXPECTED "=" AFTER KEYWORD IN DEVICE PARAMETER (FSERR 162)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 763
- MESSAGE
"ENV" BACK REFERENCE IN FILE EQUATION INCORRECT (FSERR 163)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 764
- MESSAGE
DEVICE PARAMETER TOO LARGE OR MISSING CARRIAGE RETURN (FSERR 164)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 765
- MESSAGE
INVALID DENSITY SPECIFICATION (FSERR 165)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 766
- MESSAGE
FFILEINFO FAILED IN ACCESSING REMOTE SPOOL FILE. (FSERR 166)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 767
- MESSAGE
SPOOL FILE LABEL ERROR, CAN'T INSERT ENV FILE NAME. (FSERR 167)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 768
- MESSAGE
ITEM NOT SUPPORTED ON REMOTE SYSTEM. (FSERR 168)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 770
- MESSAGE
RECORD IS MARKED FOR DELETION (FSERR 170)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 771
- MESSAGE
DUPLICATE KEY VALUE (FSERR 171)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 772
- MESSAGE
NO SUCH KEY (FSERR 172)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 773
- MESSAGE
TCOUNT PARAMETER LARGER THAN RECORD SIZE (FSERR 173)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 774
- MESSAGE
CAN NOT GET EXTRA DATA SEGMENT (FSERR 174)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 775
- MESSAGE
KSAM INTERNAL ERROR (FSERR 175)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 776
- MESSAGE
ILLEGAL EXTRA DATA SEGMENT LENGTH (FSERR 176)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 777
- MESSAGE
TOO MANY EXTRA DATA SEGMENTS FOR THIS PROCESS (FSERR 177)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 778
- MESSAGE
NOT ENOUGH VIRTUAL MEMORY FOR EXTRA DATA SEGMENT (FSERR 178)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 779
- MESSAGE
THE FILE MUST BE LOCKED BEFORE ISSUING THIS INTRINSIC (FSERR 179)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 780
- MESSAGE
KSAM FILE MUST BE REBUILT (FSERR 180)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 781
- MESSAGE
INVALID KEY STARTING POSITION (FSERR 181)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 782
- MESSAGE
FILE IS EMPTY (FSERR 182)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 783
- MESSAGE
RECORD DOES NOT CONTAIN ALL KEYS (FSERR 183)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 784
- MESSAGE
INVALID RECORD NUMBER (FFINDN INTRINSIC) (FSERR 184)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 785
- MESSAGE
SEQUENCE ERROR IN PRIMARY KEY (FSERR 185)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 786
- MESSAGE
INVALID KEY LENGTH (FSERR 186)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 787
- MESSAGE
INVALID KEY SPECIFICATION (FSERR 187)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 788
- MESSAGE
INVALID DEVICE SPECIFICATION (FSERR 188)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 789
- MESSAGE
INVALID RECORD FORMAT (FSERR 189)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 790
- MESSAGE
INVALID KEY BLOCKING FACTOR VALUE (FSERR 190)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 791
- MESSAGE
RECORD DOES NOT CONTAIN SEARCH KEY SPECIFIED FOR DELETION (FSERR 191)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 792
- MESSAGE
SYSTEM FAILURE OCCURRED WHILE THE KSAM FILE WAS OPENED (FSERR 192)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 793
- MESSAGE
$STDIN/$STDLIST CANNOT BE REDIRECTED TO KSAM FILES (FSERR 193)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 794
- MESSAGE
KSAM files not allowed for global AFT's (FSERR 194)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 795
- MESSAGE
Global files cannot be remote files (FSERR 195)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 796
- MESSAGE
LANGUAGE NOT SUPPORTED (FSERR 196)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 797
- MESSAGE
NATIVE LANGUAGE INTERNAL ERROR (FSERR 197)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 798
- MESSAGE
INVALID VERSION NUMBER IN KSAM FILE (FSERR 198)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 799
- MESSAGE
UNABLE TO SWITCH THE LOCKING MODE (FSERR 199)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 801
- MESSAGE
REMOTE DID NOT RESPOND WITH THE CORRECT REMOTE ID. (DSERR 201)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 802
- MESSAGE
SPECIFIED PHONE NUMBER IS INVALID. (DSERR 202)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 803
- MESSAGE
REMOTE ABORT/RESUME NOT VALID WHEN DOING PROGRAM-TO-PROGRAM COMMUNICATION. USE LOCAL ABORT/RESUME. (DSWARN 203)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 804
- MESSAGE
UNABLE TO ALLOCATE AN EXTRA DATA SEGMENT FOR DS/3000. (DSERR 204)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 805
- MESSAGE
UNABLE TO EXPAND THE DS/3000 EXTRA DATA SEGMENT. (DSERR 205)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 806
- MESSAGE
SLAVE PTOP FUNCTION ISSUED FROM A MASTER PROGRAM. (DSERR 206)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 807
- MESSAGE
SLAVE PTOP FUNCTION OUT OF SEQUENCE. (DSERR 207)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 808
- MESSAGE
MASTER PTOP FUNCTION ISSUED BY A SLAVE PROGRAM. (DSERR 208)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 809
- MESSAGE
SLAVE PROGRAM DOES NOT EXIST OR IS NOT PROGRAM FILE. (DSERR 209)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 810
- MESSAGE
WARNING -- INVALID MAXDATA OR DLSIZE FOR A SLAVE PROGRAM. SYSTEM DEFAULTS ARE IN EFFECT. (DSWARN 210)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 811
- MESSAGE
SLAVE ISSUED A REJECT TO A MASTER PTOP OPERATION. (DSWARN 211)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 812
- MESSAGE
FILE NUMBER FROM IOWAIT NOT A DS LINE NUMBER. (DSWARN 212)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 813
- MESSAGE
EXCLUSIVE USE OF A DS LINE REQUIRES BOTH ND AND CS CAPABILITY. (DSERR 213)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 814
- MESSAGE
DS LINE WAS NOT OPENED WITH A USER :DSLINE COMMAND. (DSERR 214)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 815
- MESSAGE
DSLINE CANNOT BE ISSUED BACK TO THE MASTER COMPUTER. (DSERR 215)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 816
- MESSAGE
MESSAGE REJECTED BY THE REMOTE COMPUTER. (DSERR 216)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 817
- MESSAGE
INSUFFICIENT AMOUNT OF USER STACK AVAILABLE. (DSERR 217)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 818
- MESSAGE
INVALID PTOP FUNCTION REQUESTED. (DSERR 218)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 819
- MESSAGE
MULTIPLE POPEN. ONLY ONE MASTER PTOP OPERATION CAN BE ACTIVE ON A DS LINE. (DSERR 219)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 820
- MESSAGE
PROGRAM EXECUTING GET WAS NOT CREATED BY POPEN. (DSERR 220)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 821
- MESSAGE
INVALID DS MESSAGE FORMAT. INTERNAL DS ERROR. (DSERR 221)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 822
- MESSAGE
MASTER PTOP FUNCTION ISSUED PRIOR TO A POPEN. (DSERR 222)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 823
- MESSAGE
REQUEST TO SEND MORE DATA THAN SPECIFIED IN POPEN. (DSERR 223)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 824
- MESSAGE
FILE EQUATIONS FOR A REMOTE FILE CONSTITUTE A LOOP. (DSERR 224)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 825
- MESSAGE
CANNOT ISSUE POPEN TO A SLAVE SESSION IN BREAK MODE. (DSERR 225)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 826
- MESSAGE
SLAVE PROGRAM HAS TERMINATED BEFORE EXECUTING "GET". (DSERR 226)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 827
- MESSAGE
RFA/RDBA COULD NOT FIND OR CREATE A REMOTE SESSION. (DSERR 227)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 828
- MESSAGE
EXCEEDED MAXIMUM NUMBER OF VIRTUAL CHANNELS PER JOB. (DSERR 228)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 829
- MESSAGE
TOO MANY DS USERS ON THIS SYSTEM. CANNOT OBTAIN A VIRTUAL PROCESS NUMBER. (DSERR 229)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 831
- MESSAGE
INVALID FACILITY IN CONNECTION REQUEST. (DSERR 231)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 832
- MESSAGE
THE REMOTE COMPUTER IS NOT OBTAINABLE. (DSERR 232)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 833
- MESSAGE
VIRTUAL CIRCUIT IS NOT AVAILABLE. (DSERR 233)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 834
- MESSAGE
QUEUEING IS REQUIRED TO COMPLETE THE REQUEST. (DSERR 234)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 835
- MESSAGE
DS MESSAGE SEQUENCING ERROR. (DSERR 235)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 836
- MESSAGE
COMMUNICATIONS HARDWARE HAS DETECTED AN ERROR. (DSERR 236)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 837
- MESSAGE
CANNOT CURRENTLY GAIN ACCESS TO THE TRACE FILE. (DSERR 237)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 838
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. INTERNAL FAILURE. (DSERR 238)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 839
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. TRACE MALFUNCTION. (DSERR 239)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 840
- MESSAGE
LOCAL COMMUNICATION LINE WAS NOT OPENED BY OPERATOR. (DSERR 240)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 841
- MESSAGE
DS LINE IN USE EXCLUSIVELY OR BY ANOTHER SUBSYSTEM. (DSERR 241)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 842
- MESSAGE
INTERNAL DS SOFTWARE ERROR ENCOUNTERED. (DSERR 242)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 843
- MESSAGE
REMOTE OR PDN IS NOT RESPONDING. (DSERR 243)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 844
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. LINE RESET OCCURRED. (DSERR 244)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 845
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. RECEIVE TIMEOUT. (DSERR 245)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 846
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. REMOTE DISCONNECTED. (DSERR 846)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 847
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. LOCAL TIME OUT. (DSERR 247)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 848
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. CONNECT TIME OUT. (DSERR 248)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 849
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. REMOTE REJECTED CONNECTION. (DSERR 249)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 850
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. CARRIER LOST. (DSERR 250)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 851
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. LOCAL DATA SET FOR THE DS LINE WENT NOT READY. (DSERR 251)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 852
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. HARDWARE FAILURE. (DSERR 252)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 853
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. NEGATIVE RESPONSE TO THE DIAL REQUEST BY THE OPERATOR. (DSERR 253)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 854
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. INVALID I/O CONFIGURATION. (DSERR 254)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
- 855
- MESSAGE
COMMUNICATIONS INTERFACE ERROR. UNANTICIPATED CONDITION. (DSERR 255)
- CAUSE
A CM error was detected.
- ACTION
File an SR.
CIERR 900 - 1499
- 939
- MESSAGE
An operation was attempted on a file type that does not support that operation. (FILE SYSTEM ERROR -939)
- CAUSE
The file is probably a CM file, or some other file with some type of implicit restrictions.
- ACTION
Do not attempt this operation with this file.
- 940
- MESSAGE
The caller lacks sufficient privilege to attempt this operation. (FILE SYSTEM ERROR -940)
- CAUSE
The caller is not privileged enough to perform this function.
- ACTION
Acquire a sufficient privilege level.
- 941
- MESSAGE
The read operation was completed due to the break key being pressed. (FILE SYSTEM ERROR -941)
- CAUSE
The user pressed the break key.
- ACTION
Retry the read operation.
- 942
- MESSAGE
A soft end of file condition was encountered. (FILE SYSTEM ERROR -942)
- CAUSE
The user typed in a colon (:) as the first character on $STDIN, or :EOD as the first characters on $STDINX.
- ACTION
Reopen the input file if you wish to continue reading.
- 943
- MESSAGE
The IOWAIT type manager layer has requested the intrinsic layer to retry the IOWAIT. (FILE SYSTEM ERROR -943)
- CAUSE
The type manager layer cannot process the I/O that was found at this time.
- ACTION
No action is necessary.
- 944
- MESSAGE
The terminal end of line character has been detected. (FILE SYSTEM ERROR -944)
- CAUSE
The end of line character was typed into the terminal.
- ACTION
No action is necessary.
- 945
- MESSAGE
Type manager; ABORT_IOX failed.
- 946
- MESSAGE
Type manager; CONVERT_DST failed.
- 947
- MESSAGE
Type manager; ATTACH_ID failed.
- 948
- MESSAGE
Type manager; The parameter passed was not valid.
- 949
- MESSAGE
The option selected is not valid in this context.
- 950
- MESSAGE
Type manager, a software error has occurred within terminal I/O software.
- 951
- MESSAGE
Type manager, an offline condition has occurred while doing a FAST WRITE to a terminal.
- 952
- MESSAGE
Type manager; a FAST WRITE to a terminal failed.
- 953
- MESSAGE
Type manager; JSINFO failed.
- 954
- MESSAGE
Type manager; a DATA MEMORY PROTECT TRAP occurred.
- 955
- MESSAGE
Type manager; a CONDITIONAL TRAP occurred.
- 956
- MESSAGE
Type manager; an OVERFLOW TRAP occurred.
- 957
- MESSAGE
Type manager; the file is busy being stored.
- 958
- MESSAGE
Type manager; this is an access violation.
- 959
- MESSAGE
Type manager; this is a multiple access error.
- 960
- MESSAGE
Type manager-directory purge; the account does not exist.
- 961
- MESSAGE
Type manager-directory purge; the group does not exist.
- 962
- MESSAGE
Type manager-directory insert; the account does not exist.
- 963
- MESSAGE
Type manager-directory insert; the group does not exist.
- 964
- MESSAGE
Type manager; invalid carriage control.
- 965
- MESSAGE
Type manager; FILE ACCESS RIGHTS TABLE DELETE failed.
- 966
- MESSAGE
Type manager; user attempted to save temporary file to existing permanent file.
- 967
- MESSAGE
Type manager directory insert; group does not have SAVE FILE capability.
- 968
- MESSAGE
Type manager directory insert; account does not have SAVE FILE capability.
- 969
- MESSAGE
Type manager-directory find; file was not found in the temporary directory.
- 970
- MESSAGE
Type manager-directory purge; the file was not found.
- 971
- MESSAGE
Type manager-directory purge; file was not found in the temporary directory.
- 972
- MESSAGE
Type manager-directory replace; file was not found in the temporary directory.
- 973
- MESSAGE
Type manager-directory find; file was not found in the temporary directory.
- 974
- MESSAGE
Type manager-directory purge; the group was not found.
- 975
- MESSAGE
Type manager directory purge; the temporary file group was not found.
- 976
- MESSAGE
Type manager-directory replace; the temporary file group was not found.
- 977
- MESSAGE
Type manager-directory find; the temporary file account was not found.
- 978
- MESSAGE
Type manager-directory purge; file account was not found.
- 979
- MESSAGE
Type manager-directory purge; the temporary file account was not found.
- 980
- MESSAGE
Type manager-directory replace; the temporary file account was not found.
- 981
- MESSAGE
Type manager-directory insert; there is no group directory disk space available.
- 982
- MESSAGE
Type manager-directory insert; there is no group disk space available for temporary file.
- 983
- MESSAGE
Type manager-directory replace; there is no group disk space available for the temporary file.
- 984
- MESSAGE
Type manager-directory insert; there is no account disk space available.
- 985
- MESSAGE
Type manager-directory insert; there is no account disk space available.
- 986
- MESSAGE
Type manager directory replace; there is no account disk space available.
- 987
- MESSAGE
Type manager-directory insert; this is a duplicate name.
- 988
- MESSAGE
Type manager-directory insert; this is a temporary file duplicate name.
- 989
- MESSAGE
Type manager-directory replace; this is a temporary file duplicate name.
- 990
- MESSAGE
Type manager; a directory I/O error occurred.
- 991
- MESSAGE
Type manager; the directory switch failed.
- 992
- MESSAGE
An error occurred while moving data to or from the user buffer. (FILE SYSTEM ERROR -992)
- CAUSE
A trap occurred while executing a MOVE_FAST.
- ACTION
Close the file, reopen and retry the operation.
- 993
- MESSAGE
An error occurred while moving data between two potentially overlapping areas. (FILE SYSTEM ERROR -993)
- CAUSE
A trap occurred while executing a MOVE_L_TO_R.
- ACTION
Close the file, reopen and retry the operation.
- 994
- MESSAGE
Type manager; the storage management READ failed.
- 995
- MESSAGE
Type manager; the storage management START READ failed.
- 996
- MESSAGE
Type manager; the storage management WRITE failed.
- 997
- MESSAGE
Type manager; the storage management START WRITE failed.
- 998
- MESSAGE
Type manager; the storage management FINISH WRITE failed.
- 999
- MESSAGE
Type manager; the storage management control failed.
- 1000
- MESSAGE
Type manager; the storage management close failed.
- 1001
- MESSAGE
Type manager; the record size was exceeded.
- 1002
- MESSAGE
Type manager; the file limit was exceeded.
- 1003
- MESSAGE
Type manager; this is an invalid request.
- 1004
- MESSAGE
Type manager; out of disk space.
- 1005
- MESSAGE
Type Manager; end of user labels.
- 1006
- MESSAGE
Type manager; the user label limit has been exceeded.
- 1007
- MESSAGE
Type manager; the GDPD reference count is negative.
- 1008
- MESSAGE
Type manager; system is out of GDPDs.
- 1009
- MESSAGE
Type manager; unable to build the GDPD table.
- 1010
- MESSAGE
Type manager; unable to unlink the GDPD.
- 1011
- MESSAGE
Type manager; unable to unlink the PLFD.
- 1012
- MESSAGE
Type manager; unable to deallocate the GDPD.
- 1013
- MESSAGE
Type manager; there is no nowait I/O for this specific file.
- 1014
- MESSAGE
Type manager; nowait I/O is pending.
- 1015
- MESSAGE
Type manager; the procedure attempted to save this file with no name.
- 1016
- MESSAGE
Type manager; the control block semaphore initialization failed.
- 1017
- MESSAGE
Type manager; the procedure was unable to get the file size.
- 1018
- MESSAGE
Type manager; this is an unimplemented function.
- 1019
- MESSAGE
Type manager; a bad variable record block was detected.
- 1020
- MESSAGE
Type manager; device type is not valid.
- 1021
- MESSAGE
Type manager; FUPDATE sequence error occurred.
- 1022
- MESSAGE
Type manager; the block size was exceeded.
- 1023
- MESSAGE
Type manager; the end-of-file has been detected.
- 1024
- MESSAGE
An invalid spooling operation was requested. (FILE SYSTEM ERROR -1024)
- CAUSE
The user specified an invalid spooling operation.
- ACTION
Do not request this operation.
- 1025
- MESSAGE
The type manager layer was not able to release all resources that were acquired. (FILE SYSTEM ERROR -1025)
- CAUSE
One or more resources could not be returned to the system.
- ACTION
File an SR.
- 1027
- MESSAGE
An error occurred while trying to access a file label extension. (FILE SYSTEM ERROR -1027)
- CAUSE
An error occurred on a call to a label management procedure.
- ACTION
File an SR.
- 1028
- MESSAGE
An error occurred while trying to access the spool file manager. (FILE SYSTEM ERROR -1028)
- CAUSE
A call to one of the spool file manager service procedures failed.
- ACTION
File an SR.
- 1029
- MESSAGE
The write operation caused the directory disk space limits to be exceeded. (FILE SYSTEM ERROR -1029)
- CAUSE
An extent fault occurred which would require allocation of more disk space than is allowed.
- ACTION
Purge unwanted files, or increase the accounting limits.
- 1030
- MESSAGE
An attempt was made to remove a file on a read-only volume. (FILE SYSTEM ERROR -1030)
- CAUSE
A purge or unlink was done against a file on a read-only volume.
- ACTION
Do not attempt a purge or an unlink on this file.
- 1031
- MESSAGE
An attempt was made to create a file in an object that is not a directory. (FILE SYSTEM ERROR -1031)
- CAUSE
An invalid path specification was provided by the caller.
- ACTION
Correct the invalid path specification.
- 1032
- MESSAGE
An attempt was made to purge a file from an object that is not a directory. (FILE SYSTEM ERROR -1032)
- CAUSE
An invalid path specification was provided by the caller.
- ACTION
Correct the invalid path specification.
- 1033
- MESSAGE
An invalid directory operation was requested. (FILE SYSTEM ERROR -1033)
- CAUSE
A directory service procedure reported an error.
- ACTION
Do not attempt this operation.
- 1034
- MESSAGE
The reserved file for the Current Working Directory has become corrupted. (FILE SYSTEM ERROR -1034)
- CAUSE
The file system could not get a pointer to the CWD reserved file.
- ACTION
Abort and restart the process.
- 1035
- MESSAGE
Directory services encountered a security violation while trying to traverse the specified path. (FILE SYSTEM ERROR -1035)
- CAUSE
The user lacks access to or through one of the directory nodes.
- ACTION
Have the system manager grant the user access to the offending directory.
- 1036
- MESSAGE
The caller lacks traverse access to one of the HFS path directory components. (FILE SYSTEM ERROR -1036)
- CAUSE
The user is not granted TD access to one or more of the components in the path.
- ACTION
Have the system adminstrator grant TD access to this user.
- 1037
- MESSAGE
The caller lacks the ability to delete entries from the target directory. (FILE SYSTEM ERROR -1037)'
- CAUSE
The user does not have DD access to the parent directory.
- ACTION
Have the system adminstrator grant DD access to this user.
- 1038
- MESSAGE
The caller lacks the ability to create entries in the target directory. (FILE SYSTEM ERROR -1038)
- CAUSE
The user lacks CD access to the parent directory or does not have SF capability.
- ACTION
Have the system administrator grant sufficient access.
- 1039
- MESSAGE
The volume set indicated by the directory mount record is not available. (FILE SYSTEM ERROR -1039)
- CAUSE
The volume set is not mounted or the disk drive is not turned on.
- ACTION
Mount the necessary volumes and make sure the drive(s) are functioning.
- 1040
- MESSAGE
Directory services encountered an error while trying to update the file label. (FILE SYSTEM ERROR -1040)
- CAUSE
An error occurred during a file label update.
- ACTION
File an SR.
- 1041
- MESSAGE
An empty path was provided to the directory services. (FILE SYSTEM ERROR -1041)
- CAUSE
The caller provided an empty path.
- ACTION
Provide a non-empty path.
- 1042
- MESSAGE
Directory services detected that a component of the path has a name length which exceeds the maximum for that directory. (FILE SYSTEM ERROR -1042)
- CAUSE
A name exceeds the directory specific name length limit.
- ACTION
Provide a shorter name.
- 1043
- MESSAGE
An attempt was made to insert a name greater than 16 characters into the root, an account, or a group. (FILE SYSTEM ERROR -1043)
- CAUSE
The caller specified a name greater than 16 characters in an MPE directory component.
- ACTION
Provide a name less than or equal to 16 characters.
- 1044
- MESSAGE
An illegal attempt was made to purge a file that was opened by UFID. (FILE SYSTEM ERROR -1044)
- CAUSE
The caller opened the file by UFID, then did an FCLOSE purge.
- ACTION
To purge this file, it must be opened with a name.
- 1046
- MESSAGE
The IOWAIT type manager layer requests the intrinsic layer to requeue the present I/O and retry the IOWAIT. (FILE SYSTEM ERROR -1046)
- CAUSE
The type manager is unable to process the I/O at this time.
- ACTION
No action is necessary.
- 1047
- MESSAGE
Incompatible version of the file.
- CAUSE
The FOPEN/HPFOPEN request has been denied because the version of the file is not compatible with the version of the operating system.
- ACTION
On a 5.0 or later system, copy the KSAM/XL file to another file specifying DEFBLK to create a compatible version of the file. Then, copy the newly created file to the pre-5.0 system
- 1050
- MESSAGE
TM_REC_TOO_SHORT: The record specified for writing is too short.
- CAUSE
The record does not have all the keys present.
- ACTION
Specify a larger record with all the keys present.
- 1051
- MESSAGE
TM_NONSEQ_WRITE: This error indicates that the current FWRITE had a primary key which was not in sequential order when compared with the previous FWRITE.
- CAUSE
A write was attempted with the primary key not in sequential order when compared with the previous write.
- ACTION
Change the order in which the records are written to the file so that the primary key is always in sequential order. Or rebuild the file and specify the SEQ flag to be false.
- 1052
- MESSAGE
TM_DUP_KEY_DISALLOWED: An attempt was made to insert a duplicate key to an index which disallows duplicate keys.
- CAUSE
One of the indexes in the file has the DUP flag set to false; however, an attempt was made to insert a key which already existed in that index.
- ACTION
Modify the record so that the key is not a duplicate of a previous record; or create the file with the index DUP flag set to TRUE.
- 1054
- MESSAGE
TM_KSM_CBLOCK_FAILED: An error was detected while scanning the B TREE where the information relating to the user specified keys is kept.
- CAUSE
This error is not currently used.
- ACTION
Nothing.
- 1055
- MESSAGE
TM_KEY_NOT_FOUND: The user specified key cannot be found in the index area of the KSAM XL file.
- CAUSE
The user may have specified a key that does not exist in the KSAM XL file.
- ACTION
Use a valid key specification.
- 1056
- MESSAGE
TM_PRIM_KEY_CHANGED: An FUPDATE call attempted to modify the primary key value.
- CAUSE
The file was opened for sequential processing and the primary key was changed while doing an FUPDATE.
- ACTION
Check the record to be written to make sure the primary key in not changed. Compare the buffer that was FREAD from the file to the buffer that you are passing to FUPDATE.
- 1057
- MESSAGE
TM_KEY_SEARCH_ERROR: An error was detected while scanning the B TREE where the information relating to the user specified keys is kept.
- CAUSE
The internal B TREE structure is corrupted.
- ACTION
Close the KSAM XL file, store it to tape, and contact your HP Support Representative.
- 1058
- MESSAGE
TM_XM_START_SYS_TRANS_FAILED: A system transaction could not be started.
- CAUSE
This is probably due to an MPE/iX operating system defect.
- ACTION
Take a memory dump and contact your HP Support Representative.
- 1059
- MESSAGE
TM_XM_END_SYS_TRANS_FAILED: A system transaction could not be terminated.
- CAUSE
This is probably due to an MPE/iX operating system defect.
- ACTION
Take a memory dump and contact your HP Support Representative.
- 1060
- MESSAGE
TM_RECORD_DELETED: The particular record in question was deleted.
- CAUSE
An attempt was made to read or update or delete a record which was deleted.
- ACTION
When positioning the data pointer before the read, make sure the pointer is not positioned to a deleted record.
- 1061
- MESSAGE
TM_BTREE_INTERNAL_ERROR: An error was detected while scanning the B TREE where the information relating to the user specified keys is kept.
- CAUSE
The internal B TREE sturucture is corrupted.
- ACTION
The KSAM XL file is corrupted. Close the KSAM file, store it to tape, and contact your HP Support Representative.
- 1062
- MESSAGE
TM_OUT_OF_INDEX_SPACE: The space reserved for the index area in the file is full and has reached the start of the data area.
- CAUSE
The B TREE is probably very sparsely filled.
- ACTION
FCOPY the KSAM XL file to another KSAM XL file. This should make more efficient use of the index blocks. If that fails, build the KSAM XL file with a larger file limit.
- 1063
- MESSAGE
TM_INVALID_KEY_SPECIFIED: The key specification provided by the user is not a valid one.
- CAUSE
The key specified in a procedure such as FREADBYKEY does not match the one specified in building the file.
- ACTION
Check the key specified in the procedure call to FREADBYKEY or FFINDBYKEY.
- 1065
- MESSAGE
TM_FFIND_FAILED: An FFINDN failed based on the relative record number specified.
- CAUSE
The relative record number specified was greater than the largest relative record number in the B TREE.
- ACTION
Check the second parameter in the call to FFINDN specifying the relative record number.
- 1066
- MESSAGE
TM_DUP_KEY_FOUND: Duplicate keys were found for the key currently being specified.
- CAUSE
The detection of the existence of duplicate keys is specificaly performed for COBOL in FREAD and FREADBYKEY intrinsics called by COBOL.
- ACTION
This status will be returned to COBOL programs only.
- 1067
- MESSAGE
TM_KSM_SPACE_FAILED: An error ocurred while doing FSPACE.
- CAUSE
The displacement specified in the FSPACE parameter is too large or too small.
- ACTION
Check the displacement specified in the FSPACE parameter.
- 1068
- MESSAGE
TM_INVALID_INDEX_RRN: An error was detected in a B TREE entry for location of a data record.
- CAUSE
The internal B TREE sturucture is corrupted.
- ACTION
Close this file and build a new file. Use FCOPY specifying KEY=0 to rebuild a new KSAM XL file.
- 1069
- MESSAGE
TM_INVALID_DATA_PTR_CALCULATED: The position of the data pointer computed is before the first data record or after the end of file.
- CAUSE
The KSAM XL file is corrupted in the data pointer of the index area.
- ACTION
Close the KSAM file, store it to tape, and contact your HP Support Representative.
- 1070
- MESSAGE
TM_INVALID_REC_NUM: An invalid recnum was specified in the call to a pointer positioning procedure such as FPOINT, or FREADDIR.
- CAUSE
A relative record number specified is not valid, either before the first record or beyond the last record.
- ACTION
Specify a valid relative record number.
- 1071
- MESSAGE
TM_DPAGE_FIND_FAILED: An error occurred while scanning for a data page with a vacant slot in it.
- CAUSE
All the data pages are used.
- ACTION
Close the file, build a new KSAM XL file with similar characteristics and FREADC from the old file and FWRITE into the new file.
- 1072
- MESSAGE
TM_KSM_NO_REC: The KSAM XL file is empty, no records in the file.
- CAUSE
An attempt was made to read or modify a KSAM XL file which has no active records in it.
- ACTION
Check the content of the file before accesssing it.
- 1073
- MESSAGE
TM_KSM_XM_ATTACH_FAILED: An error was detected while trying to attach the file to the XM log.
- CAUSE
An internal MPE/iX error occurred.
- ACTION
Take a memory dump and call your HP Support Representative.
- 1074
- MESSAGE
TM_KSM_INVALID_DATA_PTR: The logical data pointer is currently incorrectly positioned.
- CAUSE
The logical data pointer is currently position before the start of the data area or after the end of file.
- ACTION
Do an FCLOSE followed by an FOPEN or do FPOINT to reposition the data pointer.
- 1075
- MESSAGE
TM_KSM_INVALID_CHILD_PTR: An invalid child pointer was detected in the index part of the file.
- CAUSE
The internal B TREE structure is corrupted.
- ACTION
Close the KSAM file, store it to tape, and call your HP Support Representative.
- 1076
- MESSAGE
TM_KSM_CORRUPTED_FILE: During a previous KSAM operation, the KSAM file was discovered to be corrupt so that FWRITEs, FREMOVEs, and FUPDATEs are disallowed.
- CAUSE
The internal B TREE structure is corrupted.
- ACTION
Close the KSAM file, store it to tape, and call your HP Support Representative.
- 1077
- MESSAGE
The file system was unable to start a user transaction undertransaction management. (FILE SYSTEM ERROR -1077)
- CAUSE
A call to transaction management failed.
- ACTION
Make sure the file is attached to XM, otherwise file an SR.
- 1078
- MESSAGE
The file system was unable to end a user transaction under transaction management. (FILE SYSTEM ERROR -1078)
- CAUSE
A call to transaction management failed.
- ACTION
File an SR.
- 1079
- MESSAGE
An invalid offset value was provided for a KSAM/XL file. (FILE SYSTEM ERROR -1079)
- CAUSE
The user supplied an invalid file offset.
- ACTION
Supply a valid offset value to the intrinsic.
- 1080
- MESSAGE
The KSAM/XL subsystem detected an unknown internal error. (FILE SYSTEM ERROR -1080)
- CAUSE
An internal error was detected.
- ACTION
File an SR.
- 1110
- MESSAGE
The file system was unable to create the File I/O State Table. (FILE SYSTEM ERROR -1110)
- CAUSE
The FIOST table could not be created.
- ACTION
File an SR.
- 1111
- MESSAGE
The file system was unable to initialize the File I/O State Table. (FILE SYSTEM ERROR 1111)
- CAUSE
The FIOST table could not be initialized.
- ACTION
File an SR.
- 1112
- MESSAGE
The file system was unable to create the File I/O State Semaphore Table. (FILE SYSTEM ERROR -1112)
- CAUSE
An error occurred while creating the FIOST Semaphore Table.
- ACTION
File an SR.
- 1113
- MESSAGE
The file system was unable to initialize the File I/O State Semaphore Table. (FILE SYSTEM ERROR -1113)
- CAUSE
An error occurred while initializing the FIOST Semaphore Table.
- ACTION
File an SR.
CIERR 1500 - 7199
- 1500
- MESSAGE
An unexpected High-level IO error was encountered while executing a tape IO request.
- CAUSE
Either the IO request was invalid, or the device is not ready/accessible.
- ACTION
Make sure the requested IO operation is a valid one, and the devcie is accessible for the process.
- 1501
- MESSAGE
An unexpected Low-level IO error was encountered while executing the tape IO request.
- CAUSE
The device encountered an error during IO execution. It could be a medium, device or hardware error, or a driver internal error.
- ACTION
Make sure the medium and device are in a proper state. For example, check for device power, tape positioning, medium misload ... etc... If nothing wrong with the device and medium, then you should contact Hewlett-Packard for support.
- 1502
- MESSAGE
A tape IO request failed because a write access was denied.
- CAUSE
Either the medium is protected from write access, or the process does not have write access to the device.
- ACTION
Make sure the process has write access to the device and the medium is not write protected.
- 1503
- MESSAGE
The device is not ready for executing this tape IO request.
- CAUSE
Either the device is not online, or the device is not in a state ready to execute this IO request.
- ACTION
Make sure the device is on line and the medium is readily positioned.
- 1504
- MESSAGE
A tape IO request failed because the attempted device operation is not supported by the operating system.
- CAUSE
Either the requested device operation is not valid for this device, or a file system internal error was encountered.
- ACTION
Make sure the requested IO operation is valid for this device. If so, contact Hewlett-Packard for support.
- 1505
- MESSAGE
An attempt to backspace failed because the medium is already positioned at its beginning.
- CAUSE
The device was positioning at the beginning of the medium, an attempt to backspace the medium could not be performed.
- ACTION
Do not try to backspace the medium when it is positioned at its beginning.
- 1506
- MESSAGE
A tape IO operation failed because the end of the medium was encountered.
- CAUSE
An attempt was made to execute a device operation beyond the end of the medium.
- ACTION
Do not try to access the medium beyond the end of tape mark. Rewind, mount another tape and try again.
- 1507
- MESSAGE
A tape IO request failed because the device is not available for access.
- CAUSE
The specified device is not a valid one, or the device is disabled or unconfigured.
- ACTION
Check for the accessibility of the device being accessed.
- 1508
- MESSAGE
An internal error occured while processing a tape IO request.
- CAUSE
An unexpected trap occur due to a file system internal error.
- ACTION
Contact Hewlett-Packard for support.
- 1509
- MESSAGE
A bounds violation error was detected while processing a tape IO request.
- CAUSE
The address/parameter passed was inaccessible to the caller.
- ACTION
Pass only addresses in accessible spaces.
- 5000
- MESSAGE
A keyword < 0 or > VINFO_MAX_KEYWORD, or = 1 was specified; such keyword numbers are not currently supported.
- 5001
- MESSAGE
The keyvalue for the output buffer type is outside of the allowable range of VINFO_OUTPUT_MIN_PARM to VINFO_OUTPUT_MAX_PARM.
- 5002
- MESSAGE
The output buffer keyvalue pointed to an invalid range of memory for the user, or wasn't at least 4 bytes large.
- 5003
- MESSAGE
The keyvalue for the volume range is outside of the allowed range of VINFO_RANGE_MIN_PARM to VINFO_RANGE_MAX_PARM.
- 5004
- MESSAGE
The keyvalue parameter pointed to an invalid section of memory.
- 5005
- MESSAGE
The volume name contains invalid characters, or the delimiter wasn't found within the allowed number of characters.
- 5006
- MESSAGE
The volume class name contained some invalid characters, or the delimiter was not found within the allowed number of characters.
- 5007
- MESSAGE
The volume set name contained some invalid characters, or the delimiter was not found within the allowed number of characters.
- 5008
- MESSAGE
The specified generation index number was outside of the range -1..32767.
- 5009
- MESSAGE
No volumes were found in the specified range with the requested volume set, class, volume names, and the generation index.
- 5010
- MESSAGE
A keyword was specified two or more times in the intrinsic call. The latest keyword's keyvalue was used, and the previous keyvalues were ignored.
- 5011
- MESSAGE
The keyword VINFO_OPTION_END_OF_LIST (0) was specified with some keywords following it in the intrinsic call; the extra parameters were ignored.
- 5012
- MESSAGE
Neither the output buffer, nor the number of volumes in range output PARM were specified in the intrinsic call.
- 5013
- MESSAGE
The user tried to access a volume set other than his logon group's home volume set. Such access is allowed only to those with SM, OP, or CV capability.
- 5014
- MESSAGE
A volume range of one volume class was specified, but the volume class name was not specified.
- 5015
- MESSAGE
A particular volume within a given volume class was desired, and the range was set to one volume. The volume class name was given, but the particular volume name was not given.
- 5016
- MESSAGE
The user's output buffer was too small to hold all of the requested data. If the number of volumes in range parameter was specified, then the number of volumes that were actually accessed are negative.
- 5017
- MESSAGE
An error occurred during an I/O in some layer under Directory Services during a DIRECFIND.
- 5018
- MESSAGE
A failure occurred during a switch between CM and NM, or vice versa. This failure occurred somewhere within Directory Services.
- 5019
- MESSAGE
Either no GUFD/PLFD was found for the user's logon account directory, or the logon group's group entry was not found in the account directory.
- 5020
- MESSAGE
This error should be impossible to return. If it is returned, then some unexpected error was returned in a DIRECFIND. The exact MPE/iX error number may be found on the error stack.
- 5021
- MESSAGE
The volume class name was specified as an output parameter when volume searching was determined to be by volume sets; not by volume classes.
- 5022
- MESSAGE
The status parameter was pointing to an invalid section of memory.
- 5023
- MESSAGE
The volume range and volume names specification conflict. Some of the VNAMES were not needed compared to the range; therefore, the extra names were ignored.
- 5024
- MESSAGE
The KEYVAlue parameter used to specify the desired units was outside of the range VINFO_UNITS_MIN_PARM to VINFO_UNITS_MAX_PARM.
- 5100
- MESSAGE
HPVLMINFO is reserving error numbers 5000 to 5100.
- 5101
- MESSAGE
The PROCESS LOCAL FILE DESCRIPTOR TABLE is full.
- 5102
- MESSAGE
The file number does not reside in the PLFD TABLE.
- 5103
- MESSAGE
The file number specified is not within the range of possible open files.
- 6000
- MESSAGE
Storage Management SIO is not ready. (FILE SYSTEM ERROR -6000)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6001
- MESSAGE
Storage Management SIO undefined function. (FILE SYSTEM ERROR -6001)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6002
- MESSAGE
Storage Management SIO other function. (FILE SYSTEM ERROR -6002)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6003
- MESSAGE
Storage Management SIO count is too big. (FILE SYSTEM ERROR -6003)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6004
- MESSAGE
Storage Management SIO count is insufficient. (FILE SYSTEM ERROR -6004)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6008
- MESSAGE
Storage Management SIO checksum error occurred. (FILE SYSTEM ERROR -6008)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6009
- MESSAGE
Storage Management SIO invalid form. (FILE SYSTEM ERROR -6009)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6010
- MESSAGE
Storage Management SIO parity error. (FILE SYSTEM ERROR -6010)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6011
- MESSAGE
Storage Managment SIO bad access. (FILE SYSTEM ERROR -6011)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6012
- MESSAGE
Storage Managment SIO bad item. (FILE SYSTEM ERROR -6012)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6014
- MESSAGE
Storage Managment SIO unit is off. (FILE SYSTEM ERROR -6014)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6015
- MESSAGE
Storage Managment SIO deleted record. (FILE SYSTEM ERROR -6015
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6016
- MESSAGE
Storage Managment SIO no spare available. (FILE SYSTEM ERROR -6016)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6017
- MESSAGE
Storage Managment SIO blank media. (FILE SYSTEM ERROR -6017)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6018
- MESSAGE
Storage Managment SIO paper tape error. (FILE SYSTEM ERROR -6018)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6019
- MESSAGE
Storage Managment SIO system error. (FILE SYSTEM ERROR -6019)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6020
- MESSAGE
Storage Managment SIO tape error. (FILE SYSTEM ERROR -6020)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6021
- MESSAGE
Storage Managment SIO invalid disk address. (FILE SYSTEM ERROR -6021)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6023
- MESSAGE
Storage Managment SIO start I/O failure. (FILE SYSTEM ERROR -6023)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6024
- MESSAGE
Storage Managment SIO timer error. (FILE SYSTEM ERROR -6024)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6027
- MESSAGE
Storage Managment SIO vertical form control reset. (FILE SYSTEM ERROR -6027)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6028
- MESSAGE
Storage Managment SIO beginning of tape. (FILE SYSTEM ERROR -6028)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6030
- MESSAGE
Storage Managment SIO broken read. (FILE SYSTEM ERROR -6030)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6031
- MESSAGE
Storage Managment SIO timer overflow. (FILE SYSTEM ERROR -6031)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6032
- MESSAGE
Storage Managment SIO bad escape. (FILE SYSTEM ERROR -6032)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6033
- MESSAGE
Storage Managment SIO plimit. (FILE SYSTEM ERROR -6033)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6034
- MESSAGE
Storage Managment SIO tape runaway. (FILE SYSTEM ERROR -6034)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6038
- MESSAGE
Storage Managment SIO stime. (FILE SYSTEM ERROR -6038)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6040
- MESSAGE
Storage Managment SIO end of file. (FILE SYSTEM ERROR -6040)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6041
- MESSAGE
Storage Managment SIO end of tape. (FILE SYSTEM ERROR -6041)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6042
- MESSAGE
Storage Managment SIO tape error recovery. (FILE SYSTEM ERROR -6042)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6043
- MESSAGE
Storage Managment SIO end of line. (FILE SYSTEM ERROR -6043)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6044
- MESSAGE
Storage Managment SIO invalid operation. (FILE SYSTEM ERROR -6044)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6100
- MESSAGE
Terminal Storage Management read failed. (FILE SYSTEM ERROR -6100)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6101
- MESSAGE
Terminal Storage Management write failed. (FILE SYSTEM ERROR -6101)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6102
- MESSAGE
Terminal Storage Management start read failed. (FILE SYSTEM ERROR -6102)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6103
- MESSAGE
Terminal Storage Management start write failed. (FILE SYSTEM ERROR -6103)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6104
- MESSAGE
Terminal Storage Management control function failed. (FILE SYSTEM ERROR -6104)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6105
- MESSAGE
Terminal Storage Management broken read encountered. (FILE SYSTEM ERROR -6105)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6200
- MESSAGE
Storage Management Native Language I/O dependent error. (FILE SYSTEM ERROR -6200)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6201
- MESSAGE
Storage Management Native Language I/O conversion error. (FILE SYSTEM ERROR -6201)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6202
- MESSAGE
Storage Management Native Language I/O MEA error. (FILE SYSTEM ERROR -6202)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6203
- MESSAGE
Storage Management Native Language I/O judge error. (FILE SYSTEM ERROR -6203)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 6204
- MESSAGE
Storage Management Native Language I/O implementation error. (FILE SYSTEM ERROR -6204)
- CAUSE
A storage management error was detected.
- ACTION
Ensure the device is operating properly.
- 7001
- MESSAGE
The generic name translation service could not get access to CWD information. (FILE SYSTEM ERROR -7001)
- CAUSE
The reserved file for CWD has been closed or is corrupted.
- ACTION
Abort and restart the process.
- 7002
- MESSAGE
The generic name translation service found a name outside a group when it was required to be in a group. (FILE SYSTEM ERROR -7002)
- CAUSE
The name was outside of a group.
- ACTION
Ensure that the name resolves to being in a group.
- 7003
- MESSAGE
The generic name translation service could not find a component of the source name path. (FILE SYSTEM ERROR -7003)
- CAUSE
A directory is missing in the source name path.
- ACTION
Provide a valid name.
- 7004
- MESSAGE
The generic name translation service did not have room in the target array to return the name. (FILE SYSTEM ERROR -7004)
- CAUSE
The target array length is not large enough.
- ACTION
Supply a larger target array.
- 7005
- MESSAGE
The generic name translation service found a remote envorionment or a system file when it was not allowed. (FILE SYSTEM ERROR -7005)
- CAUSE
Remote environements and system files cannot be translated into some syntaxes.
- ACTION
Remove the remote environment or system file from the input name.
- 7006
- MESSAGE
The generic name translation service found no source name. (FILE SYSTEM ERROR -7006)
- CAUSE
A source name to translate was not provided.
- ACTION
Specify a source name.
- 7007
- MESSAGE
The generic name translation service received a request to translate into an unsupported syntax. (FILE SYSTEM ERROR -7007)
- CAUSE
An invalid syntax value was specified as the target syntax.
- ACTION
Supply a valid target syntax.
- 7008
- MESSAGE
The generic name translation service received a request to translate into an unknown syntax. (FILE SYSTEM ERROR -7008)
- CAUSE
An invalid syntax value was specified as the target syntax.
- ACTION
Supply a valid target syntax.
- 7009
- MESSAGE
The generic name translation service received a request to translate a name from an unknown syntax. (FILE SYSTEM ERROR -7009)
- CAUSE
An invalid syntax value was specified as the source syntax.
- ACTION
Supply a valid source syntax.
- 7010
- MESSAGE
The generic name translation service cannot translate the source name into the desired syntax. (FILE SYSTEM ERROR 7010)
- CAUSE
The source name cannot be expressed in the target syntax.
- ACTION
Pick a different target syntax.
- 7011
- MESSAGE
The generic name translation service cannot parse the source name. (FILE SYSTEM ERROR -7011)
- CAUSE
The generic name parsing service found a syntax error in the name.
- ACTION
Supply a valid source name.
- 7012
- MESSAGE
The generic name translation service was called with invalid options. (FILE SYSTEM ERROR -7012)
- CAUSE
The caller passed a bad value in the options parameter.
- ACTION
Supply a valid options parameter.
- 7101
- MESSAGE
UNABLE TO CREATE FLOD DATA STRUCTURE.
- CAUSE
An internal file system error occurred.
- ACTION
Call your HP Support Representative.
- 7102
- MESSAGE
UNABLE TO CREATE FLOD DATA STRUCTURE.
- CAUSE
An internal file system error occurred.
- ACTION
Call your HP Support Representative.
- 7103
- MESSAGE
UNABLE TO ISSUE ANOTHER LOCK REQUEST, LIMIT REACHED.
- CAUSE
The maximum number of lock requests for this file has been reached. No lock requests can be granted until some locks are released.
- ACTION
Release unneeded locks.
- 7104
- MESSAGE
INTERNAL HPFLOCK ERROR.
- CAUSE
Internal file system error.
- ACTION
Call your HP Support Representative.
- 7105
- MESSAGE
FILE WAS OPENED WITH DYNAMIC LOCKING, USE FLOCK.
- CAUSE
HPFLOCK is called on a file which was HPFOPENed with the dynamic locking option.
- ACTION
HPFOPEN the file without the dynamic locking option.
- 7106
- MESSAGE
LOCK HELD BY ANOTHER PROCESS, REQUEST DENIED.
- CAUSE
An attempt was made to lock without the wait option a record range already locked by another process.
- ACTION
Retry the request later or use the wait option.
- 7107
- MESSAGE
NO FLOD EXISTS, INCOMPATIBLE FILE TYPE.
- CAUSE
HPFLOCK does not support this file type.
- ACTION
Use FLOCK instead.
- 7108
- MESSAGE
NO SUCH LOCK EXISTS.
- CAUSE
HPFLOCKINFO, with a command parameter value of 1, was issued on a lock request which does not exist.
- ACTION
Assume no such lock exists and continue.
- 7109
- MESSAGE
WHENCE PARAMETER OUT OF BOUNDS.
- CAUSE
A value other than 0, 1, 2, or 3 was passed in for the whence parameter.
- ACTION
Pass in a legal value.
- 7110
- MESSAGE
LENGTH PARAMETER OUT OF BOUNDS.
- CAUSE
A negative value was passed for the the length parameter.
- ACTION
Pass in a non-negative number.
- 7111
- MESSAGE
START PARAMETER OUT OF BOUNDS.
- CAUSE
The value for the start parameter is beyond the file limit for the file and is therefore, invalid.
- ACTION
Determine the file limit via FFILEINFO and correctly compute the value for the start parameter.
- 7112
- MESSAGE
INTERNAL HPFLOCK ERROR.
- CAUSE
An internal file system error occurred.
- ACTION
Call your HP Support Representative.
- 7113
- MESSAGE
LOCK EXTENDS BEYOND THE FILE LIMIT.
- CAUSE
The start, length, and whence parameters combine to refer to a record beyond the file limit.
- ACTION
Determine the file limit via FFILEINFO and correctly compute the values for the start, length, and whence parameters.
- 7114
- MESSAGE
INTERNAL HPFLOCK ERROR, FLOD MARKED INVALID.
- CAUSE
An internal file system error occurred. To avoid corruption, all attempts to HPFLOCK or HPFUNLOCK the file will be denied.
- ACTION
Close all instances of the file to release all locks and allow locking on subsequent HPFLOCKs to occur.
- 7115
- MESSAGE
NO GUFD EXISTS, INCOMPATIBLE FILE TYPE.
- CAUSE
HPFLOCK does not support this file type.
- ACTION
Use FLOCK instead.
- 7116
- MESSAGE
NO GDPD EXISTS, INCOMPATIBLE FILE TYPE.
- CAUSE
HPFLOCK does not support this file type.
- ACTION
Use FLOCK instead.
- 7117
- MESSAGE
COMMAND PARAMETER OUT OF BOUNDS.
- CAUSE
A value other than 0 or 1 was passed in for the command parameter to HPFLOCKINFO.
- ACTION
Pass in a legal value.
- 7118
- MESSAGE
LOCK PARAMETER OUT OF BOUNDS.
- CAUSE
A value other than 0, 1, 2, 3, or 4 was passed in for the lock parameter to HPFLOCK.
- ACTION
Pass in a legal value.
- 7119
- MESSAGE
PIN PARAMETER OUT OF BOUNDS.
- CAUSE
An invalid value was passed in the pin parameter to HPFLOCKINFO.
- ACTION
Pass in a legal value.
- 7120
- MESSAGE
INTERRUPT OCCURED WHILE WAITING FOR LOCK.
- CAUSE
The process was aborted or an interrupt occurred while waiting for the lock request. The request was denied.
- ACTION
Retry the operation.
- 7123
- MESSAGE
SIZE PARAMETER OUT OF BOUNDS.
- CAUSE
An invalid value was passed in for the size parameter to HPFLOCKINFO.
- ACTION
Pass in a positive value.
- 7124
- MESSAGE
INVALID FILE TYPE.
- CAUSE
HPFLOCK does not support this file type.
- ACTION
Use FLOCK instead.
- 7125
- MESSAGE
LOCK TYPE AND FILE ACCESS INCOMPATIBLE.
- CAUSE
A request for a read lock was made on a file not opened with read access or a request for a write lock was made on a file not opened with write access.
- ACTION
HPFOPEN the file with the appropriate access.
- 7126
- MESSAGE
CONFLICTING READ FORMAT.
- CAUSE
The HPFLOCK request has been denied because another lock request has been granted by a process which has the file opened with a different read format.
- ACTION
Retry the operation later, or reopen the file a different read format and retry the operation.
Intrinsic Status Returns, HPSORT
(Subsystem 195)
Table of Contents