Activate SYSGEN's global module.
Enter the SYSGEN command at the system prompt.
:SYSGEN
SYSGEN version B.06.01 : catalog version B.06.02 FRI, May 20,
1988
** First level command **
io log (lo) misc (mi) spu (sp)
sysfile (sy)
basegroup (ba) keep (ke) permyes (pe) show (sh)
tape (ta)
clear (lc)(c) exit (ex)(e) help (he)(h) oclose (oc)
redo
sysgen>
|
Select the base group to modify.
If you desire to modify the default configuration groups, copy the groups to
other group names and modify the copies using the IO configurator.
Copying the groups preserves
uncorrupted versions of the default or current configurations.
To copy configuration groups, use the BASEGROUP command
to activate the desired configuration group. Use the KEEP command to save the group of files to another group name. Refer to Chapter 4 “Using the System Generator (SYSGEN)” for more information on using the BASEGROUP and KEEP commands.
After deciding which copied configuration group to modify, use the global module BASEGROUP command to activate the group:
sysgen>BASEGROUP groupname
|
Use the I/O configuration contained in CONFG935 as an
example configuration for this exercise.
Activate the IO configurator.
Enter the global module command, IO, at the SYSGEN prompt to activate the IO configurator:
sysgen>IO
** IO configurator commands **
aclass (ac) adev (ad) apath (ap) avol (av)
dclass (dc) ddev (dd) dpath (dp) dvol (dv)
lclass (lc) ldev (ld) lpath (lp) lvol (lv)
maddress(ma) mclass (mc) mdev (md) mpath (mp)
mvol (mv)
clear (cl)(c) exit (ex)(e) help (he)(h) hold (ho)
oclose (oc) redo
io>
|
Obtain I/O configuration listings.
Enter LCLASS, LDEV, and LPATH, at the IO
configurator prompt to get current I/O configuration listings:
io>LCLASS DEST=OFFLINE
io>LDEV DEST=OFFLINE
io>LPATH DEST=OFFLINE
io>OCLOSE
|
The OCLOSE command closes SYSGEN's listing file,
SYSGLIST, and prints the information in the file.
Refer to Chapter 5 “Modifying Input/Output (I/O) Configurations” for more information on using the LCLASS, LDEV, LPATH, and OCLOSE commands.
Decide on which LDEV to add the drive.
View the LDEV command output. Choose any unused LDEV and consider assigning it to the disk drive. For this example, use LDEV 4.
Decide on the class of the added peripheral.
View the LCLASS listing. If it contains a class (DISC) assigned to a particular type of peripheral (in this case, a disk drive), use that class for your addition. Remember, each device can simultaneously belong to up to eight classes.
If your configuration does not contain a class name for the
additional peripheral, the system will create a class name for you if you use a name that does not exist. Class names may not exceed eight characters and must begin with an alphabetic character.
Add the path.
Since you are adding the drive to a newly installed HP-IB card, you must define the path down to the device adapter level. Use the APATH command to define the path.
For example, add the drive to a newly installed HP-IB card (ID number, HP27113A). The HP Service Representative who installed the card placed it in the CIO expander (CA 36) on channel adapter 2, and device adapter slot 2. Enter:
Refer to Chapter 5 “Modifying Input/Output (I/O) Configurations” for additional information on using the APATH command.
Add the device.
Use the ADEV command to add the device, including the
device address, to the path specified with the APATH command.
Enter:
io>ADEV LDEV=4 PATH=36.2.0 ID=HP7937H CLASS=DISC
|
Refer to Chapter 5 “Modifying Input/Output (I/O) Configurations” for additional information on using the ADEV command.
Hold all changes.
Enter the IO configurator HOLD command at the IO
configurator prompt:
Refer to Chapter 5 “Modifying Input/Output (I/O) Configurations” for additional information on using the HOLD
command.
Exit the IO configurator.
Enter the EXIT command at the IO configurator prompt:
Save changes in a permanent file.
Enter the global module KEEP command at the SYSGEN prompt:
CONFIG is the group name under which you save the
modified files. Each time you start up the system, the group CONFIG will then be the default.
Refer to Chapter 4 “Using the System Generator (SYSGEN)” for
additional information on using the KEEP command.
Generate a boot tape.
Mount a write-enabled tape on the tape drive. Enter:
The system may place a tape request similar to the following:
?11:10/#S1/46/LDEV# FOR "SYSGTAPE" ON TAPE (NUM)?
|
If this message appears, respond:
where pin is the PIN (in this instance 46) from the third location in the tape request.
After all the files are stored, unload the tape, and write protect it. Label the tape, and store it, in a secure location, with any other backup materials.
Exit SYSGEN and reboot the system.