(Subsystem 236)

END OF FILE (FSERR 0)

Error while purging a terminating spooler process' port during cleanup.

The current state and the expected state of the spooling process do not match.

A warning occured during the cleanup of a spooling process.

A warning occured while getting information about a device.

An error occured during spooling of initially spooled devices.

Spooling of initially spooled devices is complete.

Set-up of Spooling Subsystem is complete.

An unexpected escape from an external routine was encountered.

Failed to lock the Spooler Process Information Table.

Failed to unlock the Spooler Process Information Table.

Failed attempt to retrieve information from a SPIT entry.

Failed attempt to update the SPIT entry of a spooler process.

Failed to delete SPIT entry during cleanup of terminating spooler process.

Failed attempt to use HPERRMSG routines to log an error.

Failed attempt to use GENMSG routine to display a spooler msg.

Failed to create the HPSPOOL account in the system directory.

Failed to create the OUT.HPSPOOL group in the system directory.

Failed to create the IN.HPSPOOL group in the system directory.

An unexpected escape was encountered during startup of the spooling subsystem.

Unable to delimit a device name while initially spooling devices.

Unable to convert ldev to device name while initially spooling devices.

Unable to get information about a device while initially spooling devices.

Critical error during setup of spooling system. Cannot use spooling subsystem until the system is restarted.

Error encountered while sending a system shutdown message to the Spooler Monitor's port.

A warning occured while starting the Spooler Monitor process.

The Spooler Monitor received a warning while starting a spooler process.

The Spooler Monitor received an error while purging a port. This is a non-critical error.

An escape to the RECOV block occurred after the spooler process was activated. This is a non-critical warn.

The Spooling system has been shutdown.

The Spooler Monitor received an unexpected escape during normal execution.

The Spooler Monitor could not be created.

Unable to create a spooler process for device \.

Unable to create a port for the spooler process of device \.

Unable to give port ownership to spooler process of device \.

Unable to activate the spooler process created for device \.

An error occurred while the Spooler Monitor was receiving a message on its port.

The Spooler Monitor received an invalid message on its port.

The Spooler Monitor was asked to create an invalid type of spooler process.

The Spooler Monitor was unable to lock the SPIT table.

The Spooler Monitor was unable to unlock the SPIT table.

The Spooler Monitor received an error while retrieving information from the SPIT table.

The Spooler Monitor received an error while updating an entry in the SPIT table.

The Spooler Monitor received an error while deleting an entry from the SPIT table.

The Spooler Monitor received an error during initialization.

The Spooler Monitor received an error during shutdown of the spooling subsystem.

The Spooler Monitor returned from shutdown, an event that should never occur.

You cannot run the Spooler Monitor (SPOOLMOM) as a user program.

The Spooler Monitor has entered code that should never be executed in normal situations.

Unexpected error (escape) returned from other subsystems.

Cannot find the SPIT KSO number.

Cannot lock the SPIT.

Cannot unlock the SPIT.

Cannot allocate new entry in the SPIT.

Cannot find the entry with the given device name in SPIT.

Entry with the given device name already exists in SPIT.

The given keyword is missing from the SPIT get/put interface.

Keyvalue is not passed to the SPIT get/put interface.

The given keyword is not a valid keyword for the SPIT get/put interface.

SPIT get/put interface allows only 20 key pairs, the given key index somehow is out of range.

Cannot create object for building SPIT.

Cannot create SPIT because of symbol table management error.

Cannot delete the given entry from SPIT.

The kind of process passed to SPIT interface is illegal, it must be either input or output.

Cannot send an active spoolfile message due to some error condition.

Cannot start a spooler process for an initially spooled device.

Cannot create port for the spooler MOM process.

Cannot initiate the spooler MOM process.

Cannot initiate the spooling subsystem.

Cannot create the spoolfile directory.

Cannot create the HPSPOOL accounting structure.

Spooler internal error occurred, cannot update device information.

Invalid 'DISP' specified, "SPSAVE" OR "PURGE".

Device "\" must be a printer.

Global queues or queues for device "\" must be open.

Global queues or queues for a device in class "\" must be open.

Device "\" must be spoolable for output.

A device in class "\" must be spoolable for output.

Device "\" must be spooled for output.

A device in class "\" must be spooled for output.

SPSAVED spoolfile "!" cannot be deferred.

A spoolid wildcard of the form @, I@, OR O@ was expected.

! warnings occurred.

No spoolfiles available for this spooler to process.

Attempted to remove an output spoolfile from a queue when it's not on one.

During recovery of a file still being CREATED when the system was interrupted, could not recover all data out to the file's limit.

The creator of the spoolfile did not have access to the target device during a "RAW CREATE". The spoolfile was created, but it was put in the DEFER state.

The system has finished rebuilding the output spoolfile directory.

At boot time, the system is allowed to come completely up while the output spool file directory continues to be rebuilt. This message indicates that that process has finished.

None. Informational message.

Attempted to retrieve an invalid/non-existent spoolfile attribute.

Attempted to SET an invalid/non-existent spoolfile attribute.

Internal error sequentially reading spoolfile directory entries. Possible spoolfile directory corruption.

Cannot specify both spoolfile id and UFID as file selectors.

Must specify either a spoolfile id or a UFID as a file selector.

The GETINFO intrinsic reported an error to the process rebuilding the output spoolfile directory.

Progen passes information to the process that rebuilds the output spool file directory. That process retrieves it with the GETINFO intrinsic, but the intrinsic call failed.

To recover existing spool files, STORE (;PURGE) them to tape and RESTORE them. Or SPOOLF @.OUT.HPSPOOL;PRINT them (then delete the original files). Files which were incomplete when the system was taken down may not print correctly.

Cannot find a spoolfile directory entry which is expected to exist.

Must specify either the input or output spoolfile directory.

Cannot specify both the input and output spoolfile directories.

Cannot lock the GUFD spoolfile management resource while the SPFDIR resource is locked, may cause a deadlock.

Failure occurred re-inserting an SPFDIR entry whose search key(s) have been altered. May indicate SPFDIR/disc space shortage or corruption.

Could not add an SPFDIR entry, the directory is full.

Failure attempting to gain exclusive access to a spoolfile's label and label extensions.

Could not find a spoolfile directory entry for the given UFID and directory (input or output SPFDIR).

Failure attempting to lock either the input or the output spoolfile directory.

Failure attempting to unlock either the input or the output spoolfile directory.

Unable to obtain the starting address of a spoolfile directory.

The spoolfile management architected interface routines encountered an unexpected state.

Could not gain exclusive access to a spoolfile's label and label extensions.

Could not release a spoolfile's label from exclusive access.

JOB/SESSION tried to delete a STDIN spoolfile not in the READY state.

Deletion of a spoolfile directory entry, specified by its search key, failed.

Tried to delete a STDIN spoolfile using :SPOOLF ;DELETE. Such files can only be deleted with the ABORTJOB command on the file's associated job.

Duplicate SPFDIR entry, its primary and secondary key values match those of an existing SPFDIR entry.

No spoolfile exists with the given name or UFID.

FCLOSE of spoolfile failed.

Internal error mapping from spoolfile directory entry handle to its address.

Unmatched ITEM NUMBER or ITEM in call to Spoolfile Management architected interface.

Spoolfile Management encountered an unexpected escape or trap.

Could not create a virtual object to hold the input spoolfile directory.

Could not create a virtual object to hold the output spoolfile directory.

Could not create input spoolfile directory symbol table.

Could not create output spoolfile directory symbol table.

Could not create a virtual object to hold output spoolfile queue entries.

Could not create output spoolfile queue head symbol table.

Could not re-open a spoolfile already opened by the current process.

Could not gain access to the label of a file already opened by the current process.

FCLOSE of a spoolfile failed.

Read or write of a spoolfile's label extension failed.

Spoolfile does not exist on any of the volumes currently mounted.

Low-level open of spoolfile failed due to file descriptor allocation limitations.

System error performing low-level open of spoolfile.

The spoolfile was still in the CREATE state when the system was interrupted. It could not be recovered, and has been deleted.

Infinite loop corruption detected in output spoolfile directory. Reboot your system to rebuild the directory. If the problem recurs, CONTACT YOUR SE.

Unknown error performing low-level open of spoolfile.

Output spoolfile has invalid state.

Attempt to add a new output spoolfile queue head entry failed due to existence of a queue head for the same output device or class.

Output spoolfile queue head table overflow. CONTACT YOUR SE.

Output spoolfile queue corruption detected. Invalid link to a queue's first entry. CONTACT YOUR SE.

Output spoolfile queue corruption detected. Invalid forward link. CONTACT YOUR SE.

Output spoolfile queue corruption detected. Invalid backward link. CONTACT YOUR SE.

Unexpected escape encountered inserting an output spoolfile into a spoolfile queue.

Could not find the device or class queue head entry matching the target device or class of an output spoolfile.

Could not remove a spoolfile from the spooling queues.

Could not retrieve the address of a workarea created for spooling subsystem command execution.

Could not create a spooling command/AIF work area.

Could not expand a spooling command/AIF work area.

Could not deallocate a spooling command/AIF work area.

Directory error while preparing to retrieve file system directory information for a set of spoolfiles.

Directory error while retrieving file system directory information for a set of spoolfiles.

Unknown/invalid spooler process type.

Encountered transaction management error while updating creator of an output spoolfile in its label and label extension.

Encountered error writing changes to an output spoolfile's file label extension when changing its creator.

When changing creator of an output spoolfile in its label and label extension, the changes to these structures were aborted because a user transaction under which these system transactions occurred was aborted.

SPOOLF ;PRINT encountered an error reading source file.

SPOOLF ;PRINT encountered an error writing to target file.

You cannot SPOOLF ;PRINT a Private output spoolfile.

You cannot SPOOLF ;SPSAVE a Private output spoolfile.

You cannot SPOOLF ;DEFER a spoolfile in the PROBLEM state unless you also ALTER it to a valid target device/class.

You cannot SPOOLF ;DEFER an output spoolfile which has already been printed and has moved to the 'SPSAVE' state.

You cannot alter the output priority of a spoolfile in the SPSAVE state.

You cannot alter the number of copies of a spoolfile which is either Private or in the SPSAVE state.

You cannot alter the target device/class of a spoolfile in the SPSAVE state.

SPOOLF ;ALTER or SPOOLF ;DELETE of more than one spoolfile is disabled until the output spoolfile directory has been rebuilt following a system startup.

You entered SPOOLF [O]@; ALTER or DELETE while the output spoolfile directory was still being rebuilt. This is not allowed because the command could miss some files which had not yet been inserted into the directory.

This situation only occurs for a few minutes following system startups. Try your command again a few minutes later.

The specified or defaulted target device/class does not exist, is not output spoolable, or does not have its spooling queues open.

Unable to obtain file information, the FFILEINFO intrinsic failed.

The specified file is not a spoolfile.

You tried to SPOOLF ;PRINT an empty file.

SPOOLF ;PRINT aborted by BREAK.

Could not change the STDLIST device in JOB/SESSION tables.

File does not exist or could not be created.

SPOOLF ;PRINT -- valid range of copies is 1 to 65535.

SPOOLF ;PRINT -- valid range of priorities is 0 to 14.

Cannot open the file for exclusive access because it is already open.

The specified lockword does not match the lockword on the file.

You cannot UNDEFER a spoolfile in the PROBLM state.

You cannot UNDEFER a spoolfile in the SPSAVE state.

You cannot alter the attributes of an input spoolfile.

You cannot delete an ACTIVE ":DATA" input spoolfile, that is, one currently being submitted via the STREAM command.

You cannot delete an output spoolfile which is in the CREATE state.

You cannot delete an input spoolfile which is in the OPEN state.

Only output spoolfiles can be SPOOLF ;PRINT'ed.

You cannot SPOOLF :PRINT an input spoolfile.

The source file for a SPOOLF :PRINT has no target device or class to use as a default, therefore you must specify one with the command.

The defaulted target device (taken from the source spoolfile of a SPOOLF :PRINT command) is not a valid output spooled device.

Could not open the source file for a SPOOLF :PRINT command.

Could not open the target file for a SPOOLF :PRINT command.

The first character of a file lockword must be a letter.

Too many characters were specified for the file lockword.

The file lockword contains a non-alphanumeric character.

Altering the target device of a Private spoolfile requires SM capability.

Could not change the target device of an open STDLIST.

Error encountered checking the target device

Creator of spoolfile does not have access to the target device.

If there is not an ACD on the target device, the accessor must have ND (non-sharable device) capability.

An internal call to JSINFO failed.

The creator of the spoolfile does not have access to the target device on a SPOOLF;DEV= or SPOOLF;UNDEFER. This error is used when a "Spoolid" insert is desired at the SP_AI level.

The user does not have access to the device specified in the label extension of the spoolfile. This error is used when a "file name" insert is desired at the SP_AI level.

The device specified in the label extension of the spoolfile does not have an ACD and the user does not have ND capability. This error is used when a "file name" insert is desired at the SP_AI level.

An invalid DEV keyvalue was specified in the selection equation.

Only = and <> are allowed as relational operators for the DEV selection equation keyword.

An invalid PAGES keyvalue was specified in the selection equation.

The COPIES keyvalue must be in the range of 1 to 65,535.

The PRI keyvalue must be in the range of 0 to 14.

An invalid FILEDES keyvalue was specified in the selection equation.

Only '=' and <> are allowed as relational operators for the FILEDES selection equation keyword.

Only = and <> are allowed as relational operators for the JOBNUM selectioni equation keyword.

An invalid DATE keyvalue was specified in the selection equation.

In the DATE keyvalue of the selection equation, the month must be in the range of 1 to 12.

An invalid year was specified in the DATE keyvalue of the selection equation.

An invalid JOBNUM keyvalue was specified in the selection equation.

An invalid JOBNAME keyvalue was specified in the selection equation.

An invalid FORMID keyvalue was specified in the selection equation.

You must specify an account to use this command.

A valid user name consists of a letter followed by alphanumeric characters.

A valid account name consists of a letter followed by alphanumeric characters.

The user name must contain eight or less characters.

The account name must contain eight or less characters.

The RECORDS keyvalue must be a positive integer.

Only = and <> are allowed as relational operators for the OWNER selection equation keyword.

Internal error while evaluating selection equation, there was no result to return. If this error persists, contact your SE.

The DEV keyvalue must contain eight or less characters.

Valid STATE keyvalues are READY, ACTIVE, OPEN, CREATE, PRINT, PROBLM, DELPND, SPSAVE, DEFER.

Only = and <> are allowed as relational operators for the STATE selection equation keyword.

The SPOOLID keyvalue must contain seven or fewer digits, not including the optional #0 or #1.

The FILEDES keyvalue is too long.

The JOBNUM keyvalue must be in the range of 1 to 16383.

The JOBNAME keyvalue must contain eight or less characters.

The FORMID keyvalue must contain eight or less characters.

Only = and <> are allowed as relational operators for the JOBNAME selection equation keyword.

Only = and <> are allowed as relational operators for the FORMID selection equation keyword.

The SPOOLID keyvalue must be in the range of 1 to 9999999.

The SPOOLID keyvalue must be numeric.

Only = and <> are allowed as relational operators for the SPOOLID selection equation keyword.

The only valid DISP keyvalues are SPSAVE and PURGE.

Only = and <> are allowed as relational operators for the DISP selection equation keyword.

If the "." is specified in user.acct, acct must also be specified.

An internal error occurred while validating selection equation semantics. If the error persists, contact your SE.

Expected either an 'I' or 'O' after the "#".

In the DATE keyvalue of the selection equation, the day of the month must be in the range of 1 to maximum date in month.

The only valid JOBABORT keyvalues are TRUE and FALSE.

Only = and <> are allowed as relational operators for the JOBABORT selection equation keyword.

A stop or shut spooler message was received by the input spooling process.

A BREAK or cntl-Y key was entered by the user during the STREAM command.

An EOF was received while reading from the source file being input spooled.

A record exceeding the maximum record size of 279 characters was read from the source file being input spooled.

The expanded :JOB or :DATA record exceeded the maximum record size of 279 characters.

The continuation rec for the job/data cmnd did not begin with the pseudo colon.

The :JOB or :DATA record failed to logon successfully.

The processing of the :JOB/:DATA record was interrupted before it could logon.

The setting of the spoolfile ID for the JOB's STDIN failed. The job will be flushed.

The scheduling of the JOB failed. The job will be flushed.

The scheduling of the future JOB failed. The job will be flushed.

An error occurred while printing the JOB number/DATA spoolfile ID.

Input spooler, LDEV #\: The spooler did not find a valid :JOB or :DATA command on the current tape volume.

Input spooler, LDEV #\: Device has reported a power failure or other interruption while input spooling.

Input spooler, LDEV #\: The spooler detected a non-fatal condition while performing an internal calculation. Please report the warning number to your support engineer. The spooler will continue.

Input spooler, LDEV #\: The File System reported a warning while acquiring the spooled device. The spooler will continue.

Input spooler, LDEV #\: The Device Allocation subsystem reported a warning while the spooler was retrieving device configuration information. The spooler will continue.

Input spooler, LDEV #\: The Device Allocation subsystem reported a warning while the spooler was updating device configuration information. The spooler will continue.

Input spooler, LDEV #\: A warning occurred while converting the LDEV number to a device name.

Input spooler, LDEV #\: Started.

Input spooler, LDEV #\: Stopped.

Input spooler, LDEV #\: Please mount the first tape volume to be input spooled.

Input spooler, LDEV #\: Please mount the next tape volume to be input spooled.

Input spooling code received an unexpected escape during normal execution.

You cannot run the input spooler as a user program.

Encountered error while using HPFOPEN to open the source file.

The input spooling code received an I/O error while reading from the source file being input spooled.

HPFOPEN to open a new input spoolfile failed.

FCLOSE to close a new input spoolfile failed.

The record read from the source file has more than 279 characters.

I/O error during FWRITE to input spoolfile.

Attempt to deallocate the JMAT entry of a JOB failed.

An undefined state was encountered during the input spooling process.

An undefined record kind was received from the source file.

The source file to be input spooled is not an ASCII data file.

The call to SP_FM_SET reported an error while updating the SPFDIR entry for the input spoolfile.

The FFILEINFO intrinsic reported an error while retrieving information about the input spoolfile.

The GETINFO intrinsic reported an error while retrieving information about the spooled device.

The conversion of the source file ldev to device name failed.

An error occurred while retrieving information about the source device.

An error occurred while delimiting the source device's LDEV name.

An error occurred while writing a log record to the system log file for the new input spoolfile.

An error occurred while locking the spoolfile's GUFD.

An error occurred while locking the input SPFDIR.

An error occurred while looking for the spoolfile's entry in the SPFDIR.

An error occurred while updating the owner and creator names in the spoolfile's file label and FLABX.

An error occurred while unlocking the input SPFDIR.

An error occurred while unlocking the input spoolfile's GUFD.

Input spooler, LDEV #\: The spooler detected a fatal condition while performing an internal calculation. Please report the spooling subsystem error to your support engineer.

Input spooler, Device Name !: Cannot retrieve LDEV# or other configuration info.

Input spooler, LDEV #: Cannot update device configuration tables.

Input spooler, LDEV #: Cannot open physical device.

Input spooler, LDEV #: HPFOPEN of a new input spoolfile failed.

Input spooler, LDEV #: FCLOSE of a new input spoolfile failed.

Input spooler, LDEV #: I/O error during FWRITE to input spoolfile.

Input spooler, LDEV #: Cannot update the input spoolfile's entry in the Spoolfile Directory.

An error occurred when receiving message from the spooler port.

Input spooler, LDEV #: An invalid msg type was received by the input spooling process.

Input spooler, LDEV #: The input spooled device no longer accepts :JOB or :DATA. Spooling will be stopped.

Input spooler, LDEV #: Failed to rewind and unload current tape volume. Must be done manually. Spooling will be stopped.

Input spooler, LDEV #: Spooler internal error, RECOVER invoked, spooler terminating.

Input spooler, LDEV #: A fatal error was encountered by the input spooling process. Spooling will be stopped.

Input spooler, LDEV #: A fatal error was encountered while converting the LDEV number to a device name. Spooling will be stopped.

Output spooler, LDEV #: Started.

Output Spooler, LDEV #: Stopped.

Output spooler, LDEV #: Suspended.

Output spooler, LDEV #: Resumed.

Output spooler, LDEV #: File released successfully.

Output spooler, LDEV #: Spoolfile EOF detected. NOTE: This message is never displayed.

Output spooler, LDEV #: The File System reported a warning while acquiring the spooled device. The spooler will continue.

Output spooler, LDEV #: The spooler detected a non-fatal condition while initializing its device. The spooler will continue.

Output spooler, LDEV #: The Directory subsystem reported a warning while trying to create the checkpoint file group. The spooler will continue.

Output spooler, LDEV #: The Device Allocation subsystem reported a warning while the spooler was retrieving device configuration information. The spooler will continue.

Output spooler, LDEV #: The Device Allocation subsystem reported a warning while the spooler was updating device configuration information. The spooler will continue.

Output spooler, LDEV #: The spooler detected a non-fatal condition while trying to ;RELEASE a file. The file is released and the spooler will continue.

Output spooler, LDEV #: The spooler detected a non-fatal condition while determining its next task. The spooler will continue.

Output spooler, LDEV #: The spooler detected a non-fatal condition while performing an internal calculation. Please report the warning number to your support engineer. The spooler will continue.

Output spooler, LDEV #/: The spooler detected a non-fatal condition while retrieving information from the Spooling Process Information Table (SPIT). The spooler will continue.

Output spooler, LDEV #: The spooler detected a non-fatal condition while updating the Spooling Process Information Table (SPIT). The spooler will continue.

Output spooler, LDEV #: The spooler was unable to save the page number to resume at. It will continue to use the previous value of this page.

Output spooler, LDEV #: The restart page specified is before the beginning of the spoolfile. The spooler will restart at the beginning.

Output spooler, LDEV #: There is no file to output at this time. (NOTE: This message is never displayed.)

Output spooler, LDEV #: Received a command while outputting a file.

An operator command, such as SPOOLER <ldev>;STOP was received by the spooler process for <ldev> while the process was printing user data.

No action is required. The message is to reassure the operator that the spooler got the command, because the printer may continue to print for some time afterward due to the large amount of buffered data in the file system path.

Output spooler, LDEV #: The device has reported a power failure or other interruption while outputting SPOOLID #0!. The spooler will attempt recovery.

The spooled device lost power while printing user data, causing it to lose track of where it was printing on the page. When power is restored, the the device reports the power loss to the spooler.

No user action is required. The spooler will try to recover to the beginning of the page which was partially printed at the time the device lost power.

Output spooler, LDEV #: Device status is available. (NOTE: This message is never displayed.)

Output spooler, LDEV #: "Actual device status" cannot be requested in this context. "Buffered status" will be used.

Output spooler, LDEV #: The device was still in silent-run mode when the spooler detected the end of SPOOLID #0!.

Silent-run is a recovery mechanism in which the device interprets, but does not print, data until it reaches the page at which printing should resume. If the spooler detects the end of the spoolfile first, it defers the file.

Enter SPOOLF <spoolid>;UNDEFER to print the file from the beginning. Once the file is printing, use SPOOLER ...;SUSPEND and ;RESUME with OFFSET= if you want to print from a different location.

Output spooler, LDEV #: The device reported a ribbon malfunction. The spooler will suspend. Enter a command to resume operation or to stop.

Output spooler, LDEV #: A request to mount special forms for SPOOLID #0! was refused by the device attender.

During the forms message dialog, the operator REPLYed N to the question: SP#<pin>/IS #<spoolid>; <filename> ON LDEV#<ldev> (Y/N)?

If the file should be printed on another device, enter SPOOLF <spoolid>; DEV= <new device>;UNDEFER. If it should be printed on this device but at a later time, enter SPOOLF <spoolid>; UNDEFER at that time.

Output spooler, LDEV #: The restart page specified is greater than 2^32-1, the maximum value allowed. The spooler will use the maximum value.

Output spooler, LDEV #: Device has reported a power failure or other interruption while outputting the header for SPOOLID #O!. The spooler will reprint the header.

The spooled device lost power while printing the header, causing it to lose track of where it was printing on the page. When power is restored, the device reports the power loss to the spooler.

No user action is required. The spooler automatically reprints the header.

Output spooler, LDEV #: Device has reported a power failure or other interruption while outputting the trailer for SPOOLID #O!. The spooler will reprint the trailer.

The spooled device lost power while printing the trailer, causing it to lose track of where it was printing on the page. When power is restored, the device reports the power loss to the spooler.

No user action is required. The spooler automatically reprints the trailer.

Output spooler, LDEV #: Device has reported a power failure or other interruption while outputting the error trailer for SPOOLID #O!. The spooler will reprint the error trailer.

The spooled device lost power while printing the error trailer, causing it to lose track of where it was printing on the page. When power is restored, the device reports the power loss to the spooler.

No user action is required. The spooler automatically reprints the error trailer.

Output spooler, LDEV # \ Unable to connect to printer socket after waiting ! seconds, the maximum configured for this printer. The spooler will continue trying to connect to the printer.

Output spooler, LDEV #\: The file name in the following message has been truncated to ! characters, the maximum length allowed in the message.

Output spooler, LDEV #\: FLABELINFO reported the following file system error while accessing NPCONFIG setup file !.

Output spooler, LDEV #\: Expected fixed, variable, undefined, or bytestream records for NPCONFIG setup file !.

Output spooler, LDEV #\: HPFOPEN error while opening NPCONFIG setup file !.

Output spooler, LDEV #\: File system error while FREADing NPCONFIG setup file !.

Output spooler, LDEV #\: Device does not support page level recovery. Any interrupted document will be entirely reprinted.

Output spooler, LDEV #\: Socket tracing for spoolfile !, copy ! enabled to file !

Output spooler, LDEV #\: Socket and transport tracing for spoolfile !, copy ! enabled to file !

Output spooler, LDEV #\: Check NPCONFIG. The valid range of item "!" is ! to !. The spooler will use the default value, !.

Output spooler, LDEV #\: Check NPCONFIG. Valid values of item "!" are ! and !. The spooler will use the default value, !.

Output spooler, LDEV #: Spoolfile error. There is an FCLOSE record which does not have a matching FOPEN record.

Output spooler, LDEV #: The spooler process is temporarily out of heapspace. This checkpoint file cannot be processed properly.

Output spooler, LDEV #: The spooler encountered an attempt to read the checkpoint file outside of its size.

Output spooler, LDEV #: The spooler encountered a logical error in interpreting the contents of a checkpoint file.

Output spooler, LDEV #: The spooler retrieved an entry of unknown type from the checkpoint file queues.

Output spooler, LDEV #: The spooler received a bad status from an FPOINT call while trying to set the EOF for the checkpoint file.

Output spooler, LDEV #: The spooler received a bad status from an FCONTROL call while trying to set the EOF for the checkpoint file.

Output spooler, LDEV #: The spooler was asked to purge checkpoint files for a spoolfile which is not an output spoolfile.

Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an HPDIRECSETUP error.

Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an HPDIRECREAD error.

Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an HPFOPEN error.

Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an FCLOSE error.

Output spooler, LDEV #: The spooler could not purge the checkpoint files for the spoolfile manager due to an FCLOSE error.

Output spooler, LDEV #: The spooler could not close the checkpoint files due to an FCLOSE error.

Output spooler, LDEV #: The spooler could not open the checkpoint file to use while printing a spoolfile.

Output spooler, LDEV #: The spooler encountered a trap while attempting a mapped file write to the checkpoint file.

Output spooler, LDEV #: The spooler encountered an unknown trap in the checkpoint file write procedure.

Output spooler, LDEV #: The spooler encountered an unknown trap in the checkpoint file read procedure.

Output spooler, LDEV #: The spooler encountered an unknown escape while purging checkpoint files for the spoolfile file manager.

Output spooler, LDEV #: Cannot create the checkpoint file group.

Output spooler, Device Name !: Cannot retrieve LDEV # or other configuration information.

Output spooler, LDEV #: Cannot update device configuration tables.

Output spooler, LDEV #: Could not save special forms information in device configuration tables.

Output spooler, LDEV #: Cannot open physical device.

Output spooler, LDEV #: The file system reported an error when the spooler tried to enable the device's reporting status. The spooler cannot continue.

Output spooler, LDEV #: The file system reported an error when the spooler tried to disable the device's reporting status. The spooler cannot continue.

Output spooler, LDEV #: Spooler internal error, RECOVER invoked, spooler terminating.

Output spooler, LDEV #: NM message system error. NOTE: This error is never displayed.

Output spooler, LDEV #: CM message system error. NOTE: This error is never displayed.

Output spooler, LDEV #: The spooler could not complete output of file !.

Output spooler, LDEV #: Spoolfile directory error while deferring file !.

Output spooler, LDEV #: Spoolfile directory error while saving last page number of file ! to be output.

Output spooler, LDEV #: Unknown directory service error.

You cannot run the output spooler as a user program.

Output spooler: The GETINFO intrinsic reported an error while retrieving information about the spooled device. The spooler process cannot continue.

Output spooler, LDEV #: The FFILEINFO intrinsic reported an error while retrieving a spoolfile name. The spooler process continues without it.

Output spooler, LDEV #: Error while trying to set spooler state to STOP. The spooler will terminate anyway.

Output spooler, LDEV #: Error while trying to set spooler state to ACTIVE.

Output spooler, LDEV #: Error while trying to set spooler state to SUSPEND.

Output spooler, LDEV #: Error while trying to set spooler state to IDLE.

Output spooler, LDEV #: Error while trying to set spooler state to START.

Output spooler, LDEV #: The spooler entered the INIT state, illegal once the process has started. Please contact your Hewlett-Packard support representative.

Output spooler, LDEV #: The spooler entered an unknown and illegal state. Please contact your Hewlett-Packard support representative.

Output spooler, LDEV #: Unable to determine next command.

Output spooler, LDEV #: The spooler failed to open an output spoolfile. The spooler will go idle until another file becomes ready or until you enter a command which affects the spooling process.

Output spooler, LDEV #: Internal error while deferring file !, illegal reason for deferral. Please report the spooling subsystem number to your support engineer.

When the spooler defers a file, it is for one of four causes (each described elsewhere in this document). In this case, the spooler has detected some other cause. This should never happen.

This message indicates a serious error in the code or the system as a whole. Report its number to your HP support representative.

Output spooler, LDEV #: The spooler failed to close spoolfile !.

Output spooler, LDEV #: The spooler detected an error opening or accessing checkpoint file ! for spoolfile !. Operation continues without it.

Output spooler, LDEV #: A spoolfile directory error occurred while selecting a file to print.

Output spooler, LDEV #: A spoolfile directory error occurred while preparing the Header.

Output spooler, LDEV #: A spoolfile directory error occurred while preparing the Trailer.

Output spooler, LDEV #: A spoolfile directory error occurred while getting the user's file designator for forms message processing.

Output spooler, LDEV #: A spoolfile directory error occurred while updating print job statistics during End of Job.

Output spooler, LDEV #: A spoolfile directory error occurred while obtaining print job information for the system log file.

Output spooler, LDEV #: A devicefile information error occurred while obtaining print job information for the system log file.

Output spooler, LDEV #: The system logging subsystem reported an error while obtaining print job information for the system log file.

Output spooler, LDEV #: The file system reported a device error during Start of Job processing.

Output spooler, LDEV #: The file system reported a device error during Header processing.

Output spooler, LDEV #: The file system reported a device error while outputting data.

Output spooler, LDEV #: The file system reported a device error while retrieving device status.

Output spooler, LDEV #: The file system reported a device error during spooler forms message processing.

Output spooler, LDEV #: The file system reported a device error while printing the error trailer.

Output spooler, LDEV #: The file system reported a device error during Trailer processing.

Output spooler, LDEV #: The file system reported a device error during the End of Job processing.

Output spooler, LDEV #: FCONTROL error.

Output spooler, LDEV #: FDEVICECONTROL error.

Output spooler, LDEV #: FREAD error.

Output spooler, LDEV #: FWRITE error.

Output spooler, LDEV #: The spooler received an error while waiting for nowait I/O completion.

Output spooler, LDEV #: The spooler was unable to ;RELEASE the specified file. It remains in KEEP.

Output spooler, LDEV #: Error while RESUMEing. The spooler will attempt to continue.

Output spooler, LDEV #: Error while SUSPENDing. The spooler will attempt to continue.

Output spooler, LDEV #: The spooler received a port read error.

Output spooler, LDEV #: The spooler received an invalid message type on its port.

Output spooler, LDEV #: The spooler received an unexpected escape during normal processing.

Output spooler, LDEV #: The spooler detected a fatal condition while performing an internal calculation. Please report the spooling subsystem error number to your support engineer.

Output spooler, LDEV #: The spooler could not access the Spooling Process Information Table (SPIT).

Output spooler, LDEV #: The spooler failed to update the Spooling Process Information Table (SPIT).

Output spooler, LDEV #: Spoolfile internal format error, attempted to access beyond file bounds. The file will be deferred.

Output spooler, LDEV #: Unsupported internal function code "!". Legal values are 1-4 and 64-255.

Output spooler, LDEV #: The device storage manager reported an invalid device status type "!". Please report the type and the spooling subsystem error number to your support engineer.

Output spooler, LDEV #: The device reported a parity or self-test error.

Output spooler, LDEV #: The device has insufficient memory to process data in this file.

Output spooler, LDEV #: The device has reported 100 protocol errors while processing this file.

Output spooler, LDEV #: The device has reported 100 instances of data overrun while processing this file.

Output spooler, LDEV#\: The required HPSPOOL account is missing. The spooler cannot continue.

Output spooler, LDEV #: The spooler could not open CATALOG.PUB.SYS to format the error trailer for SPOOLID #O!. The spooler will continue without printing the error trailer.

The spooler could not FOPEN CATALOG.PUB.SYS. The reason for this failure is displayed following this message.

Correct the problem with CATALOG.PUB.SYS. This allows the spooler to print future error trailers, however the spooler will not print any error trailers until the problem is corrected.

Output spooler, LDEV #: The GENMESSAGE intrinsic reported error ! while formatting the error trailer for SPOOLID #O!. The spooler will continue without printing the error trailer.

Self-explanatory.

Determine the cause of the GENMESSAGE error and correct it. This allows the spooler to print future error trailers, however the spooler will not print any error trailers until the problem is corrected.

Output spooler, LDEV #: The spooler detected a non-fatal condition while performing an internal calculation to print the error trailer for SPOOLID #O!. The spooler will continue without finishing the error trailer.

Corruption in the list of messages which make up the error trailer. The index into the list exceeded the maximum number of possible elements in the list without detection of the end-of-list mark.

Report the message number to your support engineer.

Output spooler, LDEV #: Could not set (clear) serial printer transparent mode.

Output spooler, LDEV #\: Spoolfile ! deferred due to a user command.

A user entered a SPOOLF <spoolid set>;DEFER or ALTSPOOLFILE <spoolid -or- ldev> ; DEFER which referenced the file currently being printed by this device's spooler.

This message is informational. No action is required.

Output spooler, LDEV #\: Spoolfile ! deferred due to a file error or abnormal condition.

Either of the above reasons generates an appropriate error message. Correct the situation if possible, then SPOOLF...;UNDEFER the file to try to reprint the file.

Output spooler, LDEV #\: The spooler was unable to send a message to its port.

The MPE/iX Ports Facility returned an error status to the spooler. The spooler process will terminate.

This should never happen. If it does, record all displayed messages, restart the spooler process and contact your Hewlett-Packard representative.

Output spooler, LDEV #\: Error while trying to set spooler state to SUSPEND PENDING.

An internal routine which modifies the running state of the spooler process reported an error status to the spooler. The spooler process will terminate.

This should never happen. If it does, record all displayed messages, restart the spooler process and contact your Hewlett-Packard representative.

Output spooler, LDEV #\: The spooler was unable to flush its data to the printer due to a closed connection socket.

Output spooler, LDEV #\: Error while performing the TCP graceful release handshake on the printer connection.

Output spooler, LDEV #\: Error while waiting for the printer to flush its buffered data.

Output spooler, LDEV #\: Unable to complete ABORTIO request to the printer connection socket.

Output spooler, LDEV #\: IPC error while trying to close the printer connection socket. IPCSHUTDOWN error !:

Output spooler, LDEV #\: IPC error while trying to open a printer connection socket. ADDOPT error !:

Output spooler, LDEV #\: IPC error while trying to open a printer connection socket. IPCDEST error !:

Output spooler, LDEV #\: IPC error while trying to write to the printer connection socket. IPCSEND error !:

Output spooler, LDEV #\: IPC error while trying to open a printer connection socket. IPCCONNECT error !:

Output spooler, LDEV #\: IOWAIT message destination error, sent to (spooler) port !, intended for port !.

Output spooler, LDEV #\: IPC error while initializing a printer connection socket. IPCRECV error !:

Output spooler, LDEV #\: IPC error while enabling or aborting a nowait I/O socket request. IPCCONTROL error !:!!

Output spooler, LDEV #\: Could not identify a network address for this printer. The spooler will terminate. Check NPCONFIG.PUB.SYS.

Output spooler, LDEV #\: The IOWAIT intrinsic reported a printer socket error, or an ABORTIO request was received.

Output spooler, LDEV #\: Internal error, buffer not available as expected.

Output spooler, LDEV #\: Failed to send buffered data to printer socket.

Output spooler, LDEV #\: I/O aborted by user command.

Output spooler, LDEV #\: The IOWAIT intrinsic reported condition code !.

Output spooler, LDEV #\: Internal error, the IOWAIT intrinsic completed a request with a 0 file descriptor.

Output spooler, LDEV #\: IPC error while reading printer status. IPCRECV error !:!!

Output spooler, LDEV #\: The IOWAIT intrinsic reported I/O completion on file descriptor !, expected IOWAIT file descriptor ! or printer socket file descriptor !.

Output spooler, LDEV #\: Failed to write PJL JOB command to printer. Check other error messages.

Output spooler, LDEV #\: During spooler initialization, failed to get PLFD entry for use by IOWAIT port. The spooler will terminate.

Output spooler, LDEV #\: During spooler initialization, failed to create OWAIT port. The spooler will terminate.

Output spooler, LDEV #\: Network printer internal message identifier mismatch, ID was '!', expected '!'.

Output spooler, LDEV #\: Internal IOWAIT message type "!" is not valid in this context.

Output spooler, LDEV #\: Invalid IOWAIT message type.

Output spooler, LDEV #\: Failed to obtain a system timer entry.

Output spooler, LDEV #\: The IOWAIT intrinsic reported I/O completion on file descriptor !, expected IOWAIT file descriptor !.''

Output spooler, LDEV #\: Failed to abort a timer request.

Output spooler, LDEV #\: During spooler initialization, failed to locate IOWAIT completion routine. The spooler will terminate.

Output spooler, LDEV #\: Unable to flush ! pending completions from IOWAIT port ! prior to spooler shutdown.

Output spooler, LDEV #\: Failed to write PJL USTATUS command to printer. Check other error messages.

Output spooler, LDEV #\: Unable to flush all data to printer at end of spool file.

Output spooler, LDEV #\: During spooler initialization, could not notify the LDEV's logical device manager. The spooler will terminate.

Output spooler, LDEV #\: During spooler termination, could not notify the LDEV's logical device manager.

Output spooler, LDEV #\: Sequence error, buffered data remains to be printed after the printer connection has been released.

Output spooler, LDEV #\: Unable to close printer socket. The spooler will try to continue with the present connection.

Output spooler, LDEV #\: Error while waiting for internal timed event to end.

Output spooler, LDEV #\: Received an error at line ! of NPCONFIG.PUB.SYS while retrieving configuration information.

Output spooler, LDEV #\: Failed to release timer entry !.