HP 3000 Manuals HP 3000 Manuals
To Configure DISKTRAK in PSCONFIG
1. Log on as the System Manager.
HELLO MANAGER.SYS,PRED
2. Run HP Predictive Support.
RUN PSCONFIG
_________________________________________________________________________
| |
| |
| +-------------------------------------+ |
| | | |
| | H E W L E T T - P A C K A R D | |
| | | |
| | H P P R E D I C T I V E | |
| | | |
| | S U P P O R T | |
| | | |
| +-------------------------------------+ |
| HP Predictive Version B.50.00 |
| PSCONFIG Version B.00.08 |
| |
| |
| |
| Copyright (c) Hewlett-Packard Company, 1993 |
| All rights reserved |
| |
| Please wait while Predictive checks your system's configuration. |
| |
| |
_________________________________________________________________________
_____________________________________________________________________________
| |
| |
| ******************************************************************** |
| |
| M (MainMenu) P (PreviousMenu) R (Refresh) H (Help) E (Exit) |
| |
| |
| Predictive Support Main Menu |
| |
| 1 - RUN Predictive |
| 2 - STOP Predictive |
| 3 - TRANSFER Data Menu |
| 4 - CONFIGURATION Options Menu |
| 5 - PRINT Reports Menu |
| 6 - MAINTENANCE Menu |
| |
| |
| NOTE: Predictive Support status - [next scheduled run-FRI, 2:40 AM] |
| |
| |
| Type an item number, an item key, or a command: |
| 4 |
| |
_____________________________________________________________________________
3. Select CONFIGURATION Options Menu from the Predictive Support Main
Menu.
_____________________________________________________________________________
| |
| |
| ******************************************************************** |
| |
| M (MainMenu) P (PreviousMenu) R (Refresh) H (Help) E (Exit) |
| |
| |
| Configuration Options |
| |
| 1 - CUSTOMER Information |
| 2 - TRANSFER Information |
| 3 - PERIPHERAL Devices |
| 4 - MEMORY |
| 5 - SCHEDULE |
| 6 - REPORTS Output Options |
| 7 - UTILITIES |
| 8 - CODE Word |
| |
| |
| Type an item number, an item key, or a command: |
| 7 |
| |
_____________________________________________________________________________
4. Select UTILITIES from the Configuration Options menu.
_____________________________________________________________________________
| |
| |
| ******************************************************************** |
| |
| M (MainMenu) P (PreviousMenu) R (Refresh) H (Help) E (Exit) |
| |
| |
| |
| Configure Utilities |
| |
| 1 - DISCSCAN |
| 2 - LOGSCAN |
| 3 - MEMSCAN |
| 4 - SCSICAN |
| 5 - TRANSFER |
| 6 - DISKTRAK |
| 7 - PROACTIVE Patch |
| 8 - HP OpenView |
| |
| |
| WARNING: Configuration of utilities should ONLY be done |
| if recommended by the HP Response Center or |
| the Account CE. |
| |
| |
| Type an item number, an item key, or a command: |
| 6 |
| |
_____________________________________________________________________________
5. Select DISKTRAK from the Configure Utilities menu.
_________________________________________________________________
NOTE Depending on the way HP Predictive Support was installed or
upgraded, the order of the menu items may vary.
_________________________________________________________________
__________________________________________________________________________________
| |
| |
| ******************************************************************** |
| |
| M (MainMenu) P (PreviousMenu) R (Refresh) H (Help) E (Exit) |
| |
| |
| Configure DISKTRAK |
| |
| 1 - DISKTRAK status is [disabled] |
| |
| 2 - SYSTEM volumeset threshold percentage [95] |
| |
| 3 - OTHER volumeset threshold percentage [99] |
| |
| |
| NOTE: When the percentage of permanent disk space in use on the |
| volumeset exceeds the specified threshold percentage, an event |
| is sent to the Action Summary report. The SYSTEM volumeset disk |
| space calculation formula requires that the permanent and transient |
| space be configured as the same values on each volumeset member. |
| See help for checking and modifying these values. |
| |
| Type an item number, an item key, or a command: |
| |
__________________________________________________________________________________
6. Type an item number and respond to the prompts.
* Type 1 and then E if you want to change the status to
enabled.
* Type 2 and then the configured percentage.
For example, type "75" at the "Type threshold percentage"
prompt.
* Type 3 and then the configured percentage.
For example, type "80" at the "Type threshold percentage"
prompt.
__________________________________________________________________________________
| |
| |
| ******************************************************************** |
| |
| M (MainMenu) P (PreviousMenu) R (Refresh) H (Help) E (Exit) |
| |
| |
| Configure DISKTRAK |
| |
| 1 - DISKTRAK status is [ enabled] |
| |
| 2 - SYSTEM volumeset threshold percentage [75] |
| |
| 3 - OTHER volumeset threshold percentage [80] |
| |
| |
| NOTE: When the percentage of permanent disk space in use on the |
| volumeset exceeds the specified threshold percentage, an event |
| is sent to the Action Summary report. The SYSTEM volumeset disk |
| space calculation formula requires that the permanent and transient |
| space be configured as the same values on each volumeset member. |
| See help for checking and modifying these values. |
| |
| Type an item number, an item key, or a command: |
| E |
| |
| Do you wish to save these values (Y/N)? |
| Y |
| |
| Predictive configuration has been changed. Printing Configuration |
| Summary. A copy of the Configuration Report has been sent to: |
| [Device: LP,8 ] |
| |
__________________________________________________________________________________
7. Type E to exit and then confirm saving the changes.