HP 3000 Manuals HP 3000 Manuals
ARP Logging Location Codes
1 CLAS0002 Cause: A port message was received containing an
invalid function code (PARM = function code).
Action: See "Submitting an SR" in appendix A of this
manual.
3 CLAS0004 Cause: ARP protocol started.
Action: Informative message.
12 CLAS0003 Cause: An ARP packet with a bad ARP header was
received from the link.
Action: Either the packet was corrupted in transit or
a remote node is not transmitting packets correctly.
If the latter case is suspected, see "Submitting an
SR" in appendix A of this manual.
27 CLAS0004 Cause: ARP protocol stopped.
Action: Informative message.
28 CLAS0006 Cause: ARP statistics are logged prior to port
termination.
Action: Informative message.
42 CLAS0002 Cause: Received a new (different) station address
mapping for our own IP address. This means someone
else is using our IP address.
Action: Locate the node with the duplicate IP
address.
44 CLAS0002 Cause: Call to MAP_ADD_ENTITY failed trying to add
ARP entity to the MAP table.
Action: See "Submitting an SR" in appendix A of this
manual.
49 CLAS0002 Cause: Call to MAP_LAN_UPDATE failed due to MAP
internal error.
Action: See "Submitting an SR" in appendix A of this
manual.
54 CLAS0002 Cause: Unable to create object for ARP port data
area.
Action: See "Submitting an SR" in appendix A of this
manual.
55 CLAS0002 Cause: Failed to locate ARP's ICS filter routine in
NL.PUB.SYS.
Action: See "Submitting an SR" in appendix A of this
manual.
56 CLAS0002 Cause: Failed to locate ARP's timer routine in
NL.PUB.SYS.
Action: See "Submitting an SR" in appendix A of this
manual.
57 CLAS0002 Cause: Failed to locate ARP's port procedure in
NL.PUB.SYS.
Action: See "Submitting an SR" in appendix A of this
manual.
58 CLAS0002 Cause: Unable to create the ARP port.
Action: See "Submitting an SR" in appendix A of this
manual.
59 CLAS0002 Cause: LAN_STATION_ADDRESS did not return the local
station address for the link.
Action: Issue LINKCONTROL command on the link.
Verify that the station address is valid. If the
station address is valid, see "Submitting an SR" in
appendix A of this manual.
60 CLAS0002 Cause: MAP_DEL_ENTITY failed due to an internal error
in MAP.
Action: See "Submitting an SR" in appendix A of this
manual.
61 CLAS0002 Cause: Unable to send terminate message to the
Control Process.
Action: See "Submitting an SR" in appendix A of this
manual.
62 CLAS0002 Cause: Received an unexpected message during the ARP
module termination.
Action: See "Submitting an SR" in appendix A of this
manual.
63 CLAS0002 Cause: Unable to purge the ARP port.
Action: See "Submitting an SR" in appendix A of this
manual.
64 CLAS0002 Cause: Unable to read ARP's configuration data.
Action: Verify that the NMCONFIG.PUB.SYS file exists.
If the file exists, see "Submitting an SR" in appendix
A of this manual.
65,66 CLAS0002 Cause: Failed to send ARP request out over the
network.
Action: See "Submitting an SR" in appendix A of this
manual.
67 CLAS0002 Cause: An attempt to get a buffer failed due to an
internal error in the buffer manager.
Action: See "Submitting an SR" in appendix A of this
manual.
68,69, CLAS0002 Cause: Unable to deallocate timers due to internal
71 errors in the network timers module.
Action: See "Submitting an SR" in appendix A of this
manual.
70 CLAS0002 Cause: Unable to reset a timer due to an internal
error in the network timers module.
Action: See "Submitting an SR" in appendix A of this
manual.
72 CLAS0002 Cause: Unable to abort a buffer pending request
during ARP module termination.
Action: See "Submitting an SR" in appendix A of this
manual.
73 CLAS0002 Cause: A frame too small to be an ARP packet arrived
with an ARP etype.
Action: Either the packet was corrupted in transit or
a remote node is not transmitting packets correctly.
If the latter case is suspected, see "Submitting an
SR" in appendix A of this manual.
74 CLAS0002 Cause: Failed to update the NS Registry with ARP's
port.
Action: See "Submitting an SR" in appendix A of this
manual.
75 CLAS0002 Cause: Failed to remove ARP from the NS Registry.
Action: See "Submitting an SR" in appendix A of this
manual.
76 CLAS0002 Cause: Failed to send ARP reply out over the network.
Action: See "Submitting an SR" in appendix A of this
manual.
77 CLAS0002 Cause: Failed to send ARP retransmission out over the
network.
Action: See "Submitting an SR" in appendix A of this
manual.
76 CLAS0002 Cause: Failed to send ARP reply out over the network.
Action: See "Submitting an SR" in appendix A of this
manual.
78 CLAS0002 Cause: Configuration data is corrupt.
Action: Create a new configuration file. If that
doesn't resolve the problem, see "Submitting an SR" in
appendix A of this manual.