HP 3000 Manuals HP 3000 Manuals
Data Required from the AS/400 Configuration
Data in an SNA node configuration file must correspond to information
from the remote AS/400 type 2.1 parameters. So, before using NMMGR, you
should have certain information from the AS/400 configuration.
The AS/400 information that corresponds to SNA node configuration
information for SNA/SDLC links, SNA/X.25 links, and SNA/Token Ring links
is described below.
SNA/SDLC Information
For the AS/400 and the HP 3000 to communicate, you must coordinate the
SNA/SDLC node configuration with the AS/400 configuration. The HP SNA
Products Remote System Configuration Guide (J2220-61025) explains this
configuration.
Table 2-8 shows the relationships between parameters from the AS/400
configuration and items in the SNA node configuration file for an
SNA/SDLC link. Each NMMGR screen field is described later in this
chapter.
Table 2-8. AS/400 Parameter Values for SDLC Link
----------------------------------------------------------------------------------
| | | |
| AS/400 Configuration | Field in NMMGR Screen | NMMGR Screen Name |
| Parameter | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| MAXFRAME in the line | MAX DATA | PU Data |
| description | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| LINESPEED in the line | Transmission Speed | SDLC Link Data |
| description | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| EXCHID in the controller | ID BLK combined with ID | PU Data |
| description | NUM | |
| | | |
----------------------------------------------------------------------------------
| | | |
| STNADR in the controller | Station ID | SDLC Link Data |
| description | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| RMTLOCNAME in the device | LU Name | LU Data |
| description | | |
| | | |
----------------------------------------------------------------------------------
SNA/X.25 Information
For the AS/400 and the HP 3000 to communicate, you must coordinate the
SNA/X.25 node configuration with the AS/400 configuration. The HP SNA
Products Remote System Configuration Guide [J2220-61025) explains this
configuration.
Table 2-9 shows the relationships between parameters from the AS/400
configuration and items in the SNA node configuration file for switched
virtual circuits (SVCs) of an SNA/X.25 link. Each NMMGR screen field is
described later in this chapter.
Table 2-9. AS/400 Parameter Values for X.25 Link
----------------------------------------------------------------------------------
| | | |
| AS/400 Configuration | Field in NMMGR Screen | NMMGR Screen Name |
| Parameter | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| NETADDR in the line | Remote's X.25 Network | X.25 Link Data |
| description | Address | |
| | | |
----------------------------------------------------------------------------------
SNA/Token Ring Information
For the AS/400 and the HP 3000 to communicate, you must coordinate the
SNA/Token Ring node configuration with the AS/400 configuration. The HP
SNA Products Remote System Configuration Guide (J2220-61025) explains
this configuration.
Table 2-10 shows the relationships between parameters from the AS/400
configuration and items in the SNA node configuration file for an
SNA/Token Ring link. Each NMMGR screen field is described later in this
chapter.
Table 2-10. AS/400 Parameter Values for Token Ring Link
----------------------------------------------------------------------------------
| | | |
| AS/400 Configuration | Field in NMMGR Screen | NMMGR Screen Name |
| Parameter | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| MAXFRAME in the line | MAX DATA | PU Data |
| description | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| EXCHID in the controller | ID BLK combined with ID | PU Data |
| description | NUM | |
| | | |
----------------------------------------------------------------------------------
| | | |
| ADPTADR in the line | Remote Station Address | Token Ring Link Data |
| description for the | | |
| AS/400 system | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| SSAP in the controller | Remote DSAP | Token Ring Link Data |
| description for the | | |
| AS/400 system | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| DSAP in the controller | Local SSAP | Token Ring Link Data |
| description for the HP | | |
| 3000 | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| ADPTADR in the | Local Station Address | Token Ring Link Data |
| controller description | | |
| for the HP 3000 | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| RMTCPNAME in the APPC | Local Control Point Name | PU Data |
| display controller | | |
| description (APPC only)* | | |
| | | |
----------------------------------------------------------------------------------
* If APPC is not being configured, HP recommends that you use the PU name
in the Local Control Point Name field.