HPlogo NS 3000/iX Operations and Maintenance Reference Manual > Chapter 7 Commands

NETCONTROL START

MPE documents

Complete PDF
Table of Contents
Index

Initiates the network transport, including the control process, general protocols, network interfaces, and their protocols. Also initiates individual network interfaces on an active transport.

Syntax


  NETCONTROL START  [;{NET=niName       }]
                      {GATE=gatehalfName}

Parameters

START

This function, if issued when transport is not active, initializes the control process and general protocols. When NET or GATE is also used, all configured protocols and associated modules for the specified network interface will be initialized as well, however only one such keyword may be specified per command. If you are starting several network interfaces, several commands will be required.

Unless you start network interfaces, no internetwork communications will be possible.

If the general protocols fail to start, a NETCONTROL STOP command may be required before another start can be attempted.

NET=niName

Specifies the name of a configured network interface to be started. All protocols and links configured to initially start for that NI will also be started. Enter any valid NI name from the NMMGR Network Interface Configuration screen which is not a gateway half. If neither NET nor GATE are specified, only the control process and general protocols will start. Otherwise if this is the first START, those will be started before the specified NET or GATE. If the specified entity is already running, an "ALREADY STARTED" error will occur.

GATE=gatehalfName

Specifies the name of a configured gateway half network interface to be started. All protocols and links configured to initially start for that NI will also be started. Enter any valid gatehalf NI name from the NMMGR Network Interface Configuration screen. The niName discussion for NET and GATE applies to gatehalf name also.

Discussion

In order for internetwork communications to be possible, you must activate at least one network interface using the NET keyword.

When this command is entered with an X.25 NI name, the system accesses the DTC/X.25 Network Access subsystem to verify that the X.25 line is started. If the line is not started, the command fails. If the X.25 line is started, the command is successfully completed if everything is correct. This enables the X.25 address that is associated with this system in the DTC/X.25 Network Access, and connections can be generated or accepted from this system.

Example 1

In Example 1, the node has one LAN link configured (LAN1) plus loopback (LOOP). Starting the network requires issuing a NETCONTROL START for each configured network interface (NET=niName). Once both network interfaces (and related entities) of the network transport have been successfully initiated, as indicated by the lack of error messages, any other related subsystems installed on the node can be initiated. This node, as is typically the case, has NS 3000/iX Services installed. 
:NETCONTROL START;NET=LAN1
:NETCONTROL START;NET=LOOP
:NSCONTROL START
Refer to the NSCONTROL command pages in this section for more information.

Be aware that to successfully initialize a node, the commands must be issued in the order shown: first all required NETCONTROL commands, then any NSCONTROL commands.

This first example provides an overview of initializing a node, showing where NETCONTROL fits into the process. The next five examples examine the START function and how it affects the entities defined for initialization (Figure 7-1 "The NETCONTROL Entities"). As will be shown in the examples, the keywords included with the START function and the entities affected determine which events occur at initialization. To understand this relationship, it is helpful to see the events that occur when the network transport is initialized.

Example 2

Example 2 shows the events associated with the START function at initiation. As indicated in the status report, the general transport is not active. Therefore, the first events of initiation are to initialize the control process (CP) and the general protocols. Compare the displayed events to the defined entities of Figure 7-1 "The NETCONTROL Entities". The events displayed in this example show creation of the general protocols. The START function always creates the control process and the general protocols, if they do not already exist, before acting on any of the other entities. 

  :NETCONTROL STATUS
  TRANSPORT NOT ACTIVE.  (NETXPORTWARN 0001)
  ENCOUNTERED ONE OR MORE WARNINGS WHILE PROCESSING COMMAND.
    (CIWARN 4437)

  :NETCONTROL START
  ** NETXPORT Control Process; Transport start
  - Loc: 50; Class: 4; Parm= $0000002C; PIN: 44
  ** NETXPORT TCP; General protocol start
  - Loc: 18501; Class: 4; Parm= $00865910; PortID: $FFFFDFF1
  ** NETXPORT UDP; General protocol start
  - Loc: 19; Class: 4; Parm= $00000000; PortID: $FFFFDFF2
  ** NETXPORT IP Update; General protocol start
  - Loc: 3; Class: 4; Parm= $00000000; PortID: $FFFFDFF4
  ** NETXPORT Net Timers; Starting
  - Loc: 4440; Class: 4; Parm= $00000000; PortID: $FFFFDFED
The initiation events shown in this example are always executed for the first NETCONTROL START command, whether or not a network interface is specified. However, once the general transport is initialized, subsequent NETCONTROL START commands do not change the modules of the general transport.

Example 3

Example 3 displays the error message that will appear if you issue a NETCONTROL START command when the control process is already initialized. 

  :NETCONTROL START
  ALREADY STARTED.  (NETXPORTERR 4045)
  ENCOUNTERED ONE OR MORE ERRORS WHILE PROCESSING COMMAND.
    (CIERR 4436)

Example 4

In Example 4, the LAN NI, configured as LAN1, is started on the first NETCONTROL START command. Notice that the initiation events to initialize the general protocols are immediately followed by the start of the LAN NI with its associated protocols: IP, probe, and ARP. Compare the displayed events to the defined entities of Figure 7-1 "The NETCONTROL Entities". The events displayed show creation of the control process, the general protocols, and the LAN NI entities. 

  :NETCONTROL START;NET=LAN1
  ** NETXPORT Control Process; Transport start
  - Loc: 50; Class: 4; Parm= $0000002C; PIN: 44
  ** NETXPORT TCP; General protocol start
  - Loc: 18501; Class: 4; Parm= $00865910; PortID: $FFFFDFF1
  ** NETXPORT UDP; General protocol start
  - Loc: 19; Class: 4; Parm= $00000000; PortID: $FFFFDFF2
  ** NETXPORT IP Update; General protocol start
  - Loc: 3; Class: 4; Parm= $00000000; PortID: $FFFFDFF4
  ** NETXPORT Net Timers; Starting
  - Loc: 4440; Class: 4; Parm= $00000000; PortID: $FFFFDFED
  ** NETXPORT Map Tbl; Mapping Table Created
  - Loc: 1; Class: 4; Parm= $95C80250; PortID: $95C80250
  ** NETXPORT LAN NI; Network interface start
  - Loc: 28; Class: 4; Parm= $95CC8000; PortID: $FFFFFE88
  ** NETXPORT IP; Protocol start
  - Loc: 102; Class: 4; Parm= $D4FD8000; PortID: $FFFFFE84
  ** NETXPORT Probe; Protocol start
  - Loc: 35; Class: 4; Parm= $00000000; PortID: $FFFFDFF3
  ** NETXPORT ARP; Protocol start
  - Loc: 3; Class: 4; Parm= $00000000; PortID: $FFFFDFF5

Example 5

Example 5 shows the initiation events for the loopback network interface. For this example, the loopback NI is configured as LOOP and the general protocols are already active. 

  :NETCONTROL START;NET=LOOP
  ** NETXPORT Map Tbl; Mapping Table Created
  - Loc: 1; Class: 4; Parm= $D5208250; Pin: 0
  ** NETXPORT Loopback NI; Network interface start
  - Loc: 28; Class: 4; Parm= $96038000; PortID: $FFFFFE8A
  ** NETXPORT IP; Protocol start
  - Loc: 102; Class: 4; Parm= $D5218000; PortID: $FFFFFE89
Notice that only the Loopback NI and its associated protocol, Internet Protocol (IP), are started; there was a previously issued NETCONTROL START command. Compare the displayed events to the defined entities of Figure 7-1 "The NETCONTROL Entities". The events displayed show creation of the Loopback NI entity.

Example 6

Starting the LAN NI, configured as LAN1, when the general protocols are already active, gives you the following: 

  :NETCONTROL START;NET=LAN1
  ** NETXPORT Map Tbl; Mapping Table Created
  - Loc: 1; Class: 4; Parm= $D5C80250; Pin: 0
  ** NETXPORT LAN NI; Network interface start
  - Loc: 28; Class: 4; Parm= $96430000; PortID: $FFFFFE81
  ** NETXPORT IP; Protocol start
  - Loc: 102; Class: 4; Parm= $D5CD0000; PortID: $FFFFFE88
  ** NETXPORT Probe; Protocol start
  - Loc: 35; Class: 4; Parm= $00000000; PortID: $FFFFDFF3
  ** NETXPORT ARP; Protocol start
  - Loc: 3; Class: 4; Parm= $00000000; PortID: $FFFFDFF5
Notice that only the LAN NI and its associated protocols are started. Compare the displayed events to the defined entities of Figure 7-1 "The NETCONTROL Entities". The events displayed show creation of the LAN NI entity.



NETCONTROL DELLINK

NETCONTROL STATUS