|
|
Listed are the messages that are generated by the Link Trace Formatter.
They are displayed on the user terminal when running NMDUMP.
If you must submit a CR or call your HP representative, please
copy the error exactly as it appears on the terminal; it
will make determining the CAUSE of the problem easier. These messages
are not logged.
The messages are listed in numerical order according to the
error number.
MESSAGE: SUBSYSxxTRACEFORMAT CM STUB ERROR (nnn,sss) FROM HPLOADNMPROC
UNABLE TO CALL NM TRACE FORMATTER ROUTINE (FMTERR 995) |
Level: FMTERR 995
CAUSE: The CM Stub could not load an NM WAN Trace Formatter routine
for subsystem "xx" from the system library XL.PUB.SYS.
ACTION: Incorrect software installation to run Native-Mode
Trace Formatters. The SWITCH error number is "nnn" and
the subsystem reporting the error is "sss". Call
your HP representative. |
MESSAGE: SUBSYSTEM_xx_MENU CM STUB ERROR (nnn,sss) FROM HPSWTONMNAME
UNABLE TO CALL NM MENU ROUTINE (FMTERR 996) |
Level: FMTERR 996
CAUSE: The CM Stub could not call the named NM WAN Trace Formatter
options menu routine for subsystem "xx" from the
system library XL.PUB.SYS.
ACTION: Incorrect software installation to run Native-Mode
Trace Formatters. This could also be caused by incorrect privilege
levels. The SWITCH error number is "nnn" and the
subsystem reporting the error is "sss". Call your
HP representative. |
MESSAGE: SUBSYSxxTRACEFORMAT CM STUB ERROR (nnn,sss) FROM HPSWTONMPLABEL
UNABLE TO CALL NM TRACE FORMATTER ROUTINE (FMTERR 998) |
Level: FMTERR 998
CAUSE: The CM stub successfully loaded the NM WAN Trace
Formatter routine for subsystem "xx" from the
system library XL.PUB.SYS, but could not call it.
ACTION: Incorrect software installation to run Native-Mode
Trace Formatters. This could also be caused by incorrect privilege
levels or a bug in the NM WAN Trace Formatter CM Stub. The SWITCH
error number is "nnn" and the subsystem reporting
the error is "sss". Call your HP representative. |
MESSAGE: SUBSYSxxTRACEFORMAT CM STUB ERROR (nnn,sss) FROM HPSWTONMNAME
UNABLE TO CALL NM TRACE FORMATTER ROUTINE (FMTERR 999) |
Level: FMTERR 999
CAUSE: The CM Stub could not call the named NM WAN Trace Formatter
routine for subsystem "xx" in the system library XL.PUB.SYS.
ACTION: Incorrect software installation to run Native-Mode
Trace Formatters. This could also be caused by incorrect privilege
levels. The SWITCH error number is "nnn" and the
subsystem reporting the error is "sss". Call your
HP representative. |
MESSAGE: ALL overrides other selections entered at the same time |
Level: 4024
CAUSE: Among the filter-set numbers you entered, you
also specified the number for ALL. This is a warning.
ACTION: Check your input. Unless you mistyped one of the
other set numbers, it does not make sense to specify ALL along with
other items, because ALL would include the other sets anyway. To
retype the input after this warning, you must first return to the
filter-set selection menu. |
MESSAGE: Warning: Errors always print; for Errors only don't include other sets |
Level: 4025
CAUSE: Among the filter-set numbers you entered, you
also specified the number for ERRORS-ONLY. This is a warning.
ACTION: Check your input. Unless you mistyped one of the
other set numbers, it does not make sense to specify ERRORS-ONLY
along with other items, because including the other items would
defeat the meaning of ERRORS-ONLY. To retype your input after this
warning you must first return to the filter-set selection menu. |
MESSAGE: Input truncated to 80 characters |
Level: 4026
CAUSE: The input file to the user menu was given more
than 80 characters of input, but the menu can only accept
80. This is a warning.
ACTION: If the extra characters are just extra blanks,
ignore this message or reduce the width of the input file. But if
the extra characters are nonblank, you must edit the input file,
finding a way to reduce the width of the input data to no more than
80 characters. |
MESSAGE: Extra input ignored |
Level: 4027
CAUSE: Only one number was expected, but you entered
more than one, and the extra number(s) were ignored. This is a warning.
ACTION: Check your input and, if necessary, return to that
prompt and retype the input. |
MESSAGE: Range error at position shown; other values accepted if allowed |
Level: 4028
CAUSE: One of the numbers you entered was out of range;
a "^^" indicator appears below the illegal number.
The number entered was probably much too large.
ACTION: The bad value was not accepted. Press the Return
key to keep the other values on the same line, or else
retype the entire input using only legal values. |
MESSAGE: Syntax error at position shown; other values accepted if allowed |
Level: 4029
CAUSE: Some of the numbers on the input line contained
illegal characters, or were separated by illegal characters. Legal
inputs are digits 0-9 and the question mark "?".
Legal separators for a list are the comma "," and the blank " ".
ACTION: Retype the input. |
MESSAGE: Invalid set number NN; reenter all or hit RETURN to keep others |
Level: 4030
CAUSE: One of the filter-set numbers you selected is
not one of the valid filter sets for this formatter.
ACTION: Check your input against the available sets shown in the
menu. Press the Return key to keep the other number(s) you entered
on the same line, or you may retype the entire input. You may also return
to the main menu and "set all options back to their default values." |
MESSAGE: Output limit out of range; enter another number or hit RETURN |
Level: 4031
CAUSE: You have selected a value which is less than the
lower output limit or greater than the upper output limit.
ACTION: The value you selected was not accepted. Reenter
a value which is within the range shown in the prompt. The prompt
is meant as a reminder; values up to 4096 are also legal. |
MESSAGE: Invalid option number NN ignored; others accepted |
Level: 4032
CAUSE: One of the option numbers you selected at the
main menu was not a valid option number for this formatter.
ACTION: The illegal option number was ignored, but any
other options on the same line were executed. Check your input and
retype if necessary. |
MESSAGE: Number of inputs exceeds storage capacity, rest ignored |
Level: 4033
CAUSE: Bug in Trace Formatter numeric input processing.
The formatter could not process all the numbers entered by the user.
ACTION: Check your input and retype if necessary. If the
problem continues to occur, submit an HP Change Request form against
the Trace Formatter, specifying the input you tried and the subsystem
you were trying to format. A temporary solution might be to type
fewer numbers. |
MESSAGE: CIERROR NNNN while executing MPE command |
Level: 4034
CAUSE: The MPE command you tried encountered an error.
MPE returned error number NNNN to the Formatter (MPE warnings are ignored).
ACTION: Check your input. If necessary, retype the MPE
command. You may look up the Command Interpreter error number in
the NS 3000/iX Error Messages Reference Manual. |
MESSAGE: MISSING OPT EXECUTOR #NN; PLEASE SUBMIT HP CHANGE REQUEST |
Level: 4035
CAUSE: Bug in Trace Formatter option execution processing.
The formatter recognized an option you typed, but could not find
processing for the option.
ACTION: Submit an HP Change Request form against the Formatter,
specifying what input you typed and what subsystem you were trying to
format. |
MESSAGE: MISSING MESSAGE #NNNN |
Level: none
CAUSE: Bug in Trace Formatter error message processing.
The explanatory text for error number NNNN is missing from the formatter.
ACTION: Submit an HP Change Request form against the Formatter,
specifying what input you typed and what subsystem you were trying to
format. |
|