Low Level I/O (Subsystem 113)
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II | |
| E0300 Volume I | |
| E0300 Volume II | |
| E0300 Volume III ♥ | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
 |
NOTE: Positive numbers are notes or warnings. Negative numbers are fatal errors. |
- 1
- MESSAGE
The operation was successful with retries.
- CAUSE
An I/O was attempted and was successful, but retries were required.
- ACTION
None, unless an excessive number of retries occurred. If there are an excessive number, then changing the device or the media should be looked into. Call your Hewlett-Packard Representative for assistance.
- 2
- MESSAGE
Beginning of devices media encountered.
- CAUSE
Beginning of media encountered when an I/O operation was issued.
- ACTION
None.
- 3
- MESSAGE
An attempt was made to lock a device or device manager which was already locked or unlock one not currently locked by this process.
- CAUSE
Same as message content.
- ACTION
None.
- 4
- MESSAGE
Disk contains marginal (possibly unreliable) data.
- CAUSE
Same as message content.
- ACTION
Call your Hewlett-Packard Representative.
- 5
- MESSAGE
A timeout occurred during a bind (software connect) operation.
- CAUSE
A device did not respond during configuration.
- ACTION
Check to see if device is present.
- 6
- MESSAGE
Hardware error detected during a BIND operation.
- CAUSE
A device did not respond during configuration.
- ACTION
Check to see if device is connected.
- 7
- MESSAGE
An end of file was detected.
- CAUSE
Same as message content.
- ACTION
None.
- 8
- MESSAGE
The end of the media was detected.
- CAUSE
Same as message content.
- ACTION
None.
- 9
- MESSAGE
The I/O completed successfully with some status available to be read.
- CAUSE
Same as message content.
- ACTION
None.
- 10
- MESSAGE
The read was terminated by an alternate end of record (aeor).
- CAUSE
Same as message content.
- ACTION
None.
- 11
- MESSAGE
Tape density requested is unknown or unsupported.
- CAUSE
Same as message content.
- ACTION
Verify that the tape density is appropriate for the device.
- 12
- MESSAGE
A save-set mark was detected.
- CAUSE
During an I/O operation involving the HPC1501A/HPC1511A cassette tape drive, a save-set mark (a type of index mark) was detected.
- ACTION
None.
- 13
- MESSAGE
Device adapter does not support asynchronous event notification (aen).
- CAUSE
Device or device adaptor does not support asynchronous event notification.
- ACTION
None.
- 14
- MESSAGE
Trying to remotely load a tape device that is already loaded.
- CAUSE
Same as message.
- ACTION
None.
- -75
- MESSAGE
Reservation conflict.
- CAUSE
A device (or element in the device) cannot be accessed due to a reservation conflict.
- ACTION
Retry acquisition of the device later.
- -74
- MESSAGE
Incorrect hardware type.
- CAUSE
The device or card is not of the proper type for the configured software.''
- ACTION
Verify that the configuration and involved devices are correct.
- -73
- MESSAGE
Device is unavailable.
- CAUSE
When trying to do a remotely-waited FOPEN of a device, the device is not available.
- ACTION
Retry the request later or determine why the remote device is not responding.
- -72
- MESSAGE
File does not have a correct file code.
- CAUSE
Same as message.
- ACTION
None.
- -71
- MESSAGE
Cannot open file.
- CAUSE
Same as message.
- ACTION
None.
- -70
- MESSAGE
A tape device has reported that a tape tension loss condition has occurred.
- CAUSE
Same as message.
- ACTION
None.
- -69
- MESSAGE
Special character passed in by previous FDEVICE control call.
- CAUSE
Same as message.
- ACTION
None.
- -68
- MESSAGE
A device data format error has occurred after a device power failure.
- CAUSE
Same as message.
- ACTION
None.
- -67
- MESSAGE
I/O read has been terminated by a subsystem BREAK.
- CAUSE
Same as message.
- ACTION
None.
- -66
- MESSAGE
The procedure cannot back space beyond the beginning of the media.
- CAUSE
Same as message content.
- ACTION
None.
- -65
- MESSAGE
The procedure cannot READ past the end of the volume.
- CAUSE
Same as message content.
- ACTION
None.
- -64
- MESSAGE
The device does not support the requested density.
- CAUSE
Same as message content.
- ACTION
Check file equation for incorrect density.
- -63
- MESSAGE
The device parity error count exceeded the maximum retry count.
- CAUSE
Same as message content.
- ACTION
Call your Hewlett-Packard Representative.
- -62
- MESSAGE
The I/O completed successfully, and the last available device status should now be read.
- CAUSE
Same as message content.
- ACTION
None.
- -61
- MESSAGE
The download of the firmware failed.
- CAUSE
This could be caused by a number of problems. Most likely the device being downloaded to is not present, or a hardware failure has occurred.
- ACTION
Call your Hewlett-Packard Representative.
- -60
- MESSAGE
The device could not be cleared/reset.
- CAUSE
This could be caused by a number of problems. Most likely the device is not present, or a hardware failure occurred.
- ACTION
Call your Hewlett-Packard Representative.
- -59
- MESSAGE
An incorrect hardware identification code was returned from device.
- CAUSE
Device configured does not match device type.
- ACTION
Make sure device configured matches device type.
- -58
- MESSAGE
A transmission error occurred; send the data block again.
- CAUSE
Same as message content.
- ACTION
Call your Hewlett-Packard Representative to examine link connection.
- -57
- MESSAGE
An error has occurred.
- CAUSE
An I/O error has occurred. Device status is now available that should further explain the problem.
- ACTION
None.
- -56
- MESSAGE
An invalid internal software error occurred.
- CAUSE
The operating system software module had an internal problem.
- ACTION
Call your Hewlett-Packard Representatiave.
- -55
- MESSAGE
A BREAK error occurred.
- CAUSE
Same as message content.
- ACTION
None.
- -54
- MESSAGE
READ TIME was returned.
- CAUSE
Same as message content.
- ACTION
None.
- -53
- MESSAGE
No Control Y process ID (PIN) is present.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -52
- MESSAGE
The device is off-line.
- CAUSE
Same as message content.
- ACTION
Place device online.
- -51
- MESSAGE
A RECEIVER OVERRUN occurred.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -50
- MESSAGE
A READ TIMEOUT error occurred.
- CAUSE
Device timeout occurred.
- ACTION
Call your Hewlett-Packard Representative.
- -49
- MESSAGE
A DATA TRANSMISSION error occurred.
- CAUSE
Possible problem with media or link.
- ACTION
Call your Hewlett-Packard Representative.
- -48
- MESSAGE
A data parity error was detected.
- CAUSE
A media defect or link error occurred.
- ACTION
Retry I/O operation. If problem persists, call your Hewlett-Packard Representative.
- -47
- MESSAGE
An invalid request code was detected by I/O MANAGER.
- CAUSE
Operating system software error.
- ACTION
Call your Hewlett-Packard Representative.
- -46
- MESSAGE
The request was not started or completed due to an error condition.
- CAUSE
Same as message content.
- ACTION
Determine if device is present or online. If so, call your Hewlett-Packard Representative.
- -45
- MESSAGE
Suspect data was encountered during I/O operation.
- CAUSE
Same as message content.
- ACTION
Call your Hewlett-Packard Representative.
- -44
- MESSAGE
A generic hardware problem occurred.
- CAUSE
Error condition occurred in using a device with which additional status is not available.
- ACTION
Call your Hewlett-Packard Representative.
- -43
- MESSAGE
The length of requested transfer is invalid for this device.
- CAUSE
Same as message content.
- ACTION
Length of I/O is not supported by device. Change file equation to match device supported lengths.
- -42
- MESSAGE
The format, or order of command to a device is invalid.
- CAUSE
Operating system software error.
- ACTION
Call your Hewlett-Packard Representative.
- -41
- MESSAGE
A CHANNEL TIMEOUT caused failure.
- CAUSE
A device hardware or link failure was detected.
- ACTION
Call your Hewlett-Packard Representative.
- -40
- MESSAGE
The request failed due to a device time out.
- CAUSE
Same as message content.
- ACTION
Verify that the device is connected properly and has power. Call your Hewlett-Packard Representative.
- -39
- MESSAGE
A LOWER LEVEL MANAGER error occurred; status is unknown or not available.
- CAUSE
Operating system software error.
- ACTION
Call your Hewlett-Packard Representative.
- -38
- MESSAGE
Data was lost due to a transfer error.
- CAUSE
Some sort of data transmission error.
- ACTION
Call your Hewlett-Packard Representative.
- -37
- MESSAGE
An invalid device address was requested.
- CAUSE
Operating system software error.
- ACTION
Verify that the device configuration is correct. If it is, and problem persists, call your Hewlett-Packard Representative.
- -36
- MESSAGE
Unformatted media is being used.
- CAUSE
Same as message content.
- ACTION
Format media and try operation over.
- -35
- MESSAGE
A parity, CRC, or other data type error was detected.
- CAUSE
Possible hardware, media, or link failure.
- ACTION
Call your Hewlett-Packard Representative.
- -34
- MESSAGE
The device was physically reset or the I/O request was aborted by a reset request.
- CAUSE
Same as message content.
- ACTION
None.
- -33
- MESSAGE
A device powering on condition was detected.
- CAUSE
Same as message content.
- ACTION
Determine reason for device power failure.
- -32
- MESSAGE
A write operation to a read-only device was attempted.
- CAUSE
Same as message content.
- ACTION
Determine process that attempted operation. Call your Hewlett-Packard Representative for assistance.
- -31
- MESSAGE
Operator attention is required, for example, printer is out of paper; tape needs next reel.
- CAUSE
Same as message content.
- ACTION
Take action to correct condition. For example, put paper in the printer.
- -30
- MESSAGE
An unexpected end-of-file or resource occurred; for example, disk transfer hit the end of the volume or tape hit the end-of-tape mark.
- CAUSE
Same as message content.
- ACTION
Call your Hewlett-Packard Representative.
- -29
- MESSAGE
The device is not ready or is not responding.
- CAUSE
Same as message content.
- ACTION
Place device online.
- -28
- MESSAGE
The I/O MANAGER must be locked for this request and it is not.
- CAUSE
Operating system or product software error.
- ACTION
Call your Hewlett-Packard Representative.
- -27
- MESSAGE
The I/O MANAGER has been locked by another module.
- CAUSE
Possibly an operating system or product software error.
- ACTION
This may be a normal situation if a device diagnostic tool has obtained exclusive access to the device (e.g., tape device diagnostic tools such as REELDIAG and DIAG7978 do this). Check for this situation and if this is NOT the case, call your Hewlett-Packard Representative.
- -26
- MESSAGE
A memory request error occurred.
- CAUSE
Operating system software error—Memory Manager returned an error.
- ACTION
Call your Hewlett-Packard Representative.
- -25
- MESSAGE
The procedure was unable to obtain memory necessary to continue operation.
- CAUSE
Operating system software error—Memory Manager services of the operating system returned an error.
- ACTION
Call your Hewlett-Packard Representative.
- -24
- MESSAGE
An attempt to release memory failed.
- CAUSE
Operating system software error—Memory Manager services of the operating system returned an error.
- ACTION
Call your Hewlett-Packard Representative.
- -23
- MESSAGE
Some resource was not released.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -22
- MESSAGE
The request contained incorrect higher manager port number.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -21
- MESSAGE
The DO_UNBIND operation failed.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -20
- MESSAGE
The port number of lower level I/O MANAGER is incorrect.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -19
- MESSAGE
A DO_UNBIND request was made to a nonexistent I/O MANAGER.
- CAUSE
Operating system problem.
- ACTION
Call your Hewlett-Packard Representative.
- -18
- MESSAGE
The procedure cannot UNBIND because I/O is still pending.
- CAUSE
Operating system or hardware failure.
- ACTION
Call your Hewlett-Packard Representative.
- -17
- MESSAGE
The BIND operation did not work or an UNBIND was requested of an I/O MANAGER that was not bound.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -16
- MESSAGE
The BIND request failed; manager is already bound.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -15
- MESSAGE
The BIND to lower manager failed.
- CAUSE
Operating system software problem.
- ACTION
Call you Hewlett-Packard Representative.
- -14
- MESSAGE
Bad time on bus for this BIND or DO_BIND request.
- CAUSE
Hardware failure occurred during configuration sequence.
- ACTION
Call your Hewlett-Packard Representative.
- -13
- MESSAGE
Bad critical response for this BIND or DO_BIND request.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -12
- MESSAGE
Bad bandwidth for this BIND or DO_BIND request.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -11
- MESSAGE
A bad hardware address was detected for a BIND or DO_BIND request.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -10
- MESSAGE
A bad revision code was detected for a BIND or DO_BIND request.
- CAUSE
Operating system software problem—version mismatch between modules and procedures.
- ACTION
Call your Hewlett-Packard Representative.
- -9
- MESSAGE
A bad meta tag was detected for a BIND or a DO_BIND request.
- CAUSE
Operating system software problem occurred during configuration of device manager components.
- ACTION
Call your Hewlett-Packard Representative.
- -8
- MESSAGE
A bad subsystem identifier was detected for a BIND or a DO_BIND request.
- CAUSE
Operating system problem occurred during configuration of device managers.
- ACTION
Call your Hewlett-Packard Representative.
- -7
- MESSAGE
An unclassified software problem occurred.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -6
- MESSAGE
The state of the I/O MANAGER is in appropriate for this request.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -5
- MESSAGE
The last available status was requested, but none is available yet.
- CAUSE
Possible hardware failure.
- ACTION
Call your Hewlett-Packard Representative.
- -4
- MESSAGE
The requested operation cannot be understood by the I/O MANAGER.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -3
- MESSAGE
The requested function/operation is not implemented by this I/O MANAGER.
- CAUSE
Operating system software problem.
- ACTION
Call your Hewlett-Packard Representative.
- -2
- MESSAGE
A system power failure occurred. An I/O operation was aborted or not started.
- CAUSE
Same as message content.
- ACTION
Determine why system power failure occurred.
- -1
- MESSAGE
An I/O operation was aborted by user.
- CAUSE
Same as message content.
- ACTION
Determine why I/O was aborted.
|
I/O Services (Subsystem 213) |
Measurement Interface (Subsystem 133) |