 |
» |
|
|
|
FTP users accessing the MPE/iX as an FTP server may receive
the messages and/or errors as listed, which are based on the Military
Standard, FTP, MIL-STD-1780. The type of reply is based on the first digit of the number: - Number
Type - 1nn
Positive preliminary reply - 2nn
Positive completion reply - 3nn
Positive intermediate reply - 4nn
Transient negative reply which user may wish to
retry - 5nn
Permanent negative reply
The second digit in the message number represents the following
function groupings (where the first digit x is from 1 to 5 as described
above): - Number
Type - x0n
Syntax errors - x1n
Replies to requests for information (status, help) - x2n
Replies referring to the control and data connections - x3n
Replies for logon process and accounting procedures - x4n
Unspecified - x5n
Status of the server file system
In the following list of messages and errors, the exclamation
point (!) represents a variable value. MESSAGE: 125 Data
connection already open; transfer starting | CAUSE: Data connection
has been opened, data transfer has started. ACTION: None. |
MESSAGE: 150 File
! opened; data connection will be opened | CAUSE: The file
requested for a GET, LS, or DIR
has been opened. ACTION: None. |
MESSAGE: 200 ! command
ok. | CAUSE: The command
was accepted by the server. ACTION: None. |
MESSAGE: 200 Type
set to !. | CAUSE: A TYPE
command was received and accepted. ACTION: None. |
MESSAGE: 202 Command
not implemented at this site. | CAUSE: The MPE/iX
FTP server received a command that is not implemented. ACTION: This command cannot
be used. |
MESSAGE: "1":
!. | CAUSE: A file
status (SIZE | MDTM) command was received
and accepted. This first parameter is the filename. The second contains
detailed information that differs depending on the command. ACTION: |
MESSAGE: MPE/iX system
type. | CAUSE: The server
received a SYST command. ACTION: None. |
MESSAGE: 220 HP ARPA
File Transfer Protocol Server [!] (C) Hewlett-Packard Co. 1990 | CAUSE: The server
has been started and is ready for user commands. ACTION: Enter FTP commands. |
MESSAGE: 221 Server
is closing command connection | CAUSE: The server
received a QUIT command and is shutting down. ACTION: None. |
MESSAGE: 226 Transfer
complete. | CAUSE: A file
transfer for a GET, PUT, LS
or DIR has completed. ACTION: None. |
MESSAGE: 226 Transfer
complete. Some records were truncated during transfer. | CAUSE: A data
transfer to MPE/iX resulted in some records being truncated in the
target file. ACTION: It may be necessary
to increase the maximum record size using build parameters. Review
the HP ARPA FTP User's Guide for more information
on this subject. |
MESSAGE: 230 User
logged on | CAUSE: A USER
command was received and accepted. The logon has succeeded. ACTION: None. |
MESSAGE: 250 File
transfer completed. | CAUSE: A file
transfer for a GET, PUT, LS
or DIR has completed. ACTION: None. |
MESSAGE: ! is the
current directory. "!" is the current session. | CAUSE: A PWD
command was received and accepted. ACTION: None. |
MESSAGE: ! successful,
"!" created. | CAUSE: A directory
creation (MKD/XMKD) has completed. ACTION: |
MESSAGE: 331 Password
required for !. [userpass][,acctpass][,grouppass] | CAUSE: A USER
command has been received, the server is waiting for the password. ACTION: Enter the passwords
required. |
MESSAGE: 350 File
exists, ready for destination name.] | CAUSE: An RNFR
(rename from) command has been received, the server is waiting for
a RNTO (rename to). This is part of the user RENAME
command. ACTION: None. |
MESSAGE: 426 Data
transfer aborted | CAUSE: The data
connection could not be opened or there was a network error during
the file transfer. ACTION: Try the transfer
again. If this doesn't work, try exiting FTP and connecting
again, then transferring the file. If that doesn't work,
check for a networking problem (resources, connection establishment,
etc.) on both systems. |
MESSAGE: 500 Unknown
command | CAUSE: The MPE/iX
FTP server received an unrecognized command. ACTION: This command cannot
be used. |
MESSAGE: 501 Syntax
error in parameter ! | CAUSE: One of
the parameters in the command was not correct. The ! will contain
the parameter in question. ACTION: Check the parameter
and try again. |
MESSAGE: 502 Command
not implemented by this server. | CAUSE: The MPE/iX
FTP server received an unrecognized command. ACTION: This command cannot
be used. |
MESSAGE: 503 Illegal
sequence of commands | CAUSE: The server
was sent a series of commands that were in the wrong order (example:
RNTO before RNFR). ACTION: Check the commands
and send them in the correct order. |
MESSAGE: 504 Command
not implemented for parameter ! | CAUSE: A parameter
was specified that is not supported. For example TYPE EBCDIC is
NOT supported by the MPE/iX FTP server. ACTION: Specify a parameter
which is supported. |
MESSAGE: 530 User
log on unsuccessful | CAUSE: The server
received a user account and/or password which were not valid. ACTION: Specify the correct
user account and password. If the user is sure that they are correct,
notify the network manager and have him/her refer to the Installing
and Managing HP ARPA File Transfer Protocol Network Manager's Guide. |
MESSAGE: 530 Please
login with USER and PASS. | CAUSE: The user
entered a command without being logged on to the FTP server. ACTION: Log on with the USER
command, then enter the command again. |
MESSAGE: 550 File
request not taken: ! | CAUSE: An MPE/iX
File System error was received. The parameter will contain the text
of the specific File System error. ACTION: Refer to the MPE/iX
Error Messages Manual. |
MESSAGE: 553 Illegal
file name | CAUSE: The file
name specified was not a valid MPE/iX file name. ACTION: Use the correct file
name format: either filename or filename.group.account
where each file name part is up to eight alphanumeric characters,
beginning with an alphabetic character. |
|
