 |
» |
|
|
|
Compiles an HP C/iX program. HP C/iX is not part of the HP
3000 Series 900 Computer System Fundamental Operating Software and
must be purchased separately. This command is recognized only if
HP C/iX is installed on your system. (Native Mode) Parameters | |
- textfile
The name of the text file that contains the source
code to be compiled. This is an ASCII file that you prepare with
an editor such as EDIT/3000. The formal file designator is CCTEXT. If you are running HP C/iX from your terminal, you will probably
specify a disk textfile. If you do not
specify textfile, then the default file
is $STDIN. $STDIN
is the current input device, usually your terminal. When textfile is your terminal,
you can enter source code interactively. When you have entered all
the source code, type a colon (:)
to end the interactive input. - objectfile
Actual file designator of the object file to which
the object code is stored. This file is in binary form and has a
file code of 1461
or NMOBJ. Its
formal file designator is CCOBJ.
If the objectfile parameter is omitted,
the object code is saved to the temporary file $OLDPASS. If you specify objectfile, the
compiler stores the object file in a permanent file of the correct
size, type, and name you specified. If a file of the same name already
exists, the object code overwrites that file. If the compiler issues an error message telling you that a
new or existing object file to which you are trying to compile is
too small, build a larger object file and recompile to it. You may use the MPE/iX SAVE
command to store $OLDPASS
as a permanent file under another name. - listfile
The name of the file on which the compiler writes
the program listing. It can be any ASCII file. The default is $STDLIST.$STDLIST
is usually the terminal from a session or the printer from a batch
job. The formal file designator is CCLIST. If listfile is $NULL
or a file other than $STDLIST,
the compiler displays on $STDLIST
those lines that contain errors. - quotedstring
A string of no more than 1024 characters (including
the single or double quotation marks that enclose it). The quotedstring is used to pass
initial compiler options to the compiler program. Options must be
delimited by blank spaces.
| | | |  | NOTE: The formal file designators used in this command (CCTEXT,
CCOBJ, and CCLIST)
cannot be backreferenced as actual file designators in the command
parameter list. | | | | |
Use | |
This command may be issued from a session, job, or program.
It may not be used in BREAK. Pressing Break
suspends the execution of this command. Entering the RESUME
command continues the execution. Examples | |
The following example compiles an HP C/iX program entered
from your standard input device and stores the object program in
the object file $OLDPASS.
The listing is then sent to your standard list device. The next example compiles an HP C/iX program contained in
the disk file SOURCE
and stores the object program in the object file OBJECT.
The program listing is stored in the disk file LISTFILE. CCXL SOURCE,OBJECT,LISTFILE |
Program development in native mode uses the MPE/iX LINK
command, not the MPE V/E PREP
command. This produces a significant change in the method of linking
code. In MPE/iX, you must compile the source files into separate
object files and then use the Link Editor to link the two object
files into the program file, as in this example: CCXL MAIN, OBJMAIN
CCXL SUB, OBJSUB
LINK FROM=OBJMAIN,OBJSUB;TO=SOMEPROG;RL=LIBCINIT.LIB.SYS
RUN SOMEPROG |
Related Information | |
- Commands
CCXLGO,
CCXLLK, RUN,
LINK, XEQ,
LINKEDIT Utility - Manuals
HP C Programmer's Guide
|
