 |
» |
|
|
|
Listed below are the codes that are generated by the X.25 link Qualified
Logical Link Control (QLLC) module when a QLLC internal error occurs. They
are listed in numerical order according to the ProcNum
displayed as part of these SNA Transport logging messages:
Link connect failure on node NodeName
subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
Link failure, recovery in progress on node NodeName
subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
Link failure, shutting down the node NodeName
subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
|
The logging messages are described in "SNA Transport Logging Messages"
earlier in this appendix. The X.25 link-related ErrorNum
values are described in "X.25 Link Failure Error Codes" earlier
in this appendix. -
-1
-
MESSAGE
NETIPC ERROR DETECTED -
CAUSE
The QLLC module was informed of a socket error (SOCKERR) by NETIPC. -
ACTION
Note the socket error number and see the NS3000/XL
Error Messages Reference Manual (36923-61000) for socket error
information.
-
-2
-
MESSAGE
AFT ERROR -
CAUSE
The QLLC module encountered an error while trying to
obtain the available file table (AFT). -
ACTION
Call your Hewlett-Packard support contact.
-
-3
-
MESSAGE
INSTALLATION ERROR -
CAUSE
The SNA/X.25 Link IOWAIT completor is not
installed on the system. -
ACTION
Call your Hewlett-Packard support contact.
-
-4
-
MESSAGE
QLLC PORT CREATION ERROR -
CAUSE
The QLLC module encountered an error while trying to
create its IOWAIT port. -
ACTION
Call your Hewlett-Packard support contact.
-
-5
-
MESSAGE
PORT SUBQUEUE ERROR -
CAUSE
The QLLC module encountered an error while trying to
enable its IOWAIT port subqueues. -
ACTION
Call your Hewlett-Packard support contact.
-
-6 through-16
-
MESSAGE
(reserved for internal use only) -
CAUSE
An internal error has occurred. -
ACTION
Call your Hewlett-Packard support contact.
-
-17
-
MESSAGE
CALL REJECTED DUE TO SECURITY VIOLATION -
CAUSE
An incoming SVC call was rejected by SNA/X.25 because
the caller was unauthorized. That is, the caller's address was not
included in the call packet, or it was not the remote address the
SNA node is configured for. -
ACTION
Verify that the Remote's X.25 Network
Address field of the "SNA Node Configuration: X.25 Link
Data" screen contains the correct X.25 address for the host node. Also
verify that the DIALNO operand of the PATH macro
in the host's switched major node definition contains the IBM's X.25
address and the HP 3000's X.25 address.
-
-18
-
MESSAGE
(reserved for internal use only) -
CAUSE
An internal error has occurred. -
ACTION
Call your Hewlett-Packard support contact.
-
-19
-
MESSAGE
SECURITY VIOLATION -
CAUSE
A non-system process tried to launch the QLLC module. -
ACTION
Call your Hewlett-Packard support contact.
-
-20
-
MESSAGE
RECEIVED INVALID QLLU -
CAUSE
An unrecognizable QLLC control frame (QLLU) was received
from the remote system. -
ACTION
Call your Hewlett-Packard support contact.
-
-21
-
MESSAGE
INFO FIELD NOT ALLOWED -
CAUSE
A QLLU that information fields are not allowed for was received with an information field. -
ACTION
Call your Hewlett-Packard support contact.
-
-22
-
MESSAGE
INFO TOO LONG -
CAUSE
A QLLU containing an information field that is too long was received. -
ACTION
Call your Hewlett-Packard support contact.
-
-23 through -26
-
MESSAGE
INTERNAL ERROR -
CAUSE
An internal error has occurred. -
ACTION
Call your Hewlett-Packard support contact.
-
-27 through -49
-
MESSAGE
(reserved for internal use only) -
CAUSE
An internal error has occurred. -
ACTION
Call your Hewlett-Packard support contact.
-
-50 through -100
-
MESSAGE
INTERNAL ERROR -
CAUSE
An internal error has occurred. -
ACTION
Call your Hewlett-Packard support contact.
|
