 |
» |
|
|
|
Listed below are the error codes that are generated by the X.25 link module configurator. These messages are displayed on the HP 3000 operator's console. They are listed here in numerical order according to the ErrorCode displayed as part of these SNA Transport logging messages:
Attempt to close link failed on node NodeName
Subsystem = 734, Error Code = ErrorCode
Attempt to open link failed on node NodeName
Subsystem = 734, Error Code = ErrorCode
|
The logging messages are described in "SNA Transport Logging Messages" earlier in this appendix. - -200
- MESSAGE
CONFIG OPEN ERROR
- CAUSE
The module configurator encountered an error while trying to open the configuration file.
- ACTION
Verify that the NMCONFIG.PUB.SYS configuration file exists.
- -201
- MESSAGE
CONFIG RETRIEVAL ERROR
- CAUSE
The module configurator encountered an error while retrieving the SNA/X.25 link configuration information for the current SNA node.
- ACTION
Verify that the correct version of NMMGR is installed on the system, and that an X.25 link is configured for the SNA node being started.
- -202
- MESSAGE
PROCESS CREATION ERROR
- CAUSE
The module configurator was unable to launch the Qualified Logical Link Control (QLLC) module.
- ACTION
Verify that the file containing the QLLC module (SNAX25.PUB.SYS) exists.
- -203
- MESSAGE
TRACE OPEN ERROR
- CAUSE
The module configurator was unable to open the trace file.
- ACTION
Issue the SNACONTROL START command with the trace file name specified for the LINKTRACE parameter. If the error still occurs, issue the SNACONTROL START command without specifying a trace file name (that is, let the default file name be used). If the error still occurs, call your Hewlett-Packard support contact.
- -204
- MESSAGE
STATUS BUFFER INVALID
- CAUSE
The Qualified Logical Link Control (QLLC) module returned an invalid buffer containing the link status information. Note that the node can still function, but link status information cannot be retrieved.
- ACTION
Call your Hewlett-Packard support contact.
- -205
- MESSAGE
STATUS REPLY INVALID
- CAUSE
The module configurator status routine received an invalid status reply. Note that the node can still function, but link status information cannot be retrieved.
- ACTION
Call your Hewlett-Packard support contact.
- -500
- MESSAGE
UNABLE TO RECEIVE OPENLINK COMPLETION MESSAGE
- CAUSE
The module configurator encountered an error while trying to receive the OpenLink completion message.
- ACTION
Call your Hewlett-Packard support contact.
- -501
- MESSAGE
UNABLE TO GET MSG FRAME FOR CLOSELINK REQUEST
- CAUSE
The module configurator encountered an error while trying to allocate the CloseLink request message.
- ACTION
Call your Hewlett-Packard support contact.
- -502
- MESSAGE
UNABLE TO SEND CLOSELINK REQUEST
- CAUSE
The module configurator encountered an error while trying to send the CloseLink request message.
- ACTION
Call your Hewlett-Packard support contact.
- -503
- MESSAGE
UNABLE TO RECEIVE CLOSELINK COMPLETION MESSAGE
- CAUSE
The module configurator encountered an error while trying to receive the CloseLink completion message.
- ACTION
Call your Hewlett-Packard support contact.
- -504
- MESSAGE
UNABLE TO GET MSG FRAME FOR TRACE ENABLE REQUEST
- CAUSE
The module configurator encountered an error while trying to allocate the trace enable request message.
- ACTION
Call your Hewlett-Packard support contact.
- -505
- MESSAGE
UNABLE TO SEND TRACE ENABLE REQUEST - CAUSE
The module configurator encountered an error while trying to send the trace enable request message. - ACTION
Call your Hewlett-Packard support contact.
- -506
- MESSAGE
UNABLE TO SEND TRACE DISABLE REQUEST - CAUSE
The module configurator encountered an error while trying to send the trace disable request message. - ACTION
Call your Hewlett-Packard support contact.
- -507
- MESSAGE
UNABLE TO GET MESSAGE FRAME FOR TRACE DISABLE REQUEST - CAUSE
The module configurator encountered an error while trying to allocate the trace disable request message. - ACTION
Call your Hewlett-Packard support contact.
- -508
- MESSAGE
UNABLE TO GET MESSAGE FRAME FOR STATUS REQUEST - CAUSE
The module configurator encountered an error while trying to allocate the status request message. - ACTION
Call your Hewlett-Packard support contact
- -509
- MESSAGE
UNABLE TO SEND STATUS REQUEST - CAUSE
The module configurator encountered an error while trying to send the status request message. - ACTION
Call your Hewlett-Packard support contact.
- -510
- MESSAGE
UNABLE TO RECEIVE STATUS COMPLETION MESSAGE - CAUSE
The module configurator encountered an error while trying to receive the status completion message. - ACTION
Call your Hewlett-Packard support contact.
|
