HP 3000 Manuals HP 3000 Manuals
Resource Manager Utility
This section explains errors you may encounter when using the Resource
Manager Utility (RESMGR).
RSM3001 Unable to access error message catalog.
RESMGR is unable to access the error message catalog. It may be secured
against access or be missing entirely.
Check the security on the file and release it if necessary. If the
file is missing, use the MPE Restore function to restore the current
catalog file.
RSM3002 Command too long.
Your entry exceeded the allowable limit of characters per command. If
you were using the REDO command, you may have inserted (I) or replaced
(R) enough characters to make the existing command string too long.
Retype the command using fewer characters.
RSM3003 Illegal redo character.
You typed an illegal REDO character. Valid characters are I (insert), R
(replace), D (delete) and U (undo).
Retype the command.
RSM3004 This is a nonexistent command.
The command you typed was not recognized by either RESMGR or MPE. RESMGR
commands are context-sensitive, and are recognized only in their
appropriate functional areas.
Type the corrected command.
RSM3005 Disc error reading data from host.
RESMGR encountered an MPE file system error while trying to read data
from the HP 3000.
Read the MPE error message for more information.
RSM3006 Disc error writing data to host.
RESMGR encountered an MPE file system error while trying to write data to
the HP 3000.
Read the MPE error message for more information.
RSM3007 Unable to open localization file. Default used.
RESMGR was unable to find the requested localization file. A
localization file allows local language translations of the screen
displays and messages. This is an informational message. The program
continues, using the default language, Native-3000.
You may need to re-install the localization file.
RSM3008 Unable to register with the diagnostic program.
Each time RESMGR runs, it identifies itself to the Diagnostic program.
This error occurs when RESMGR is unable to locate the Diagnostic program.
It doesn't prevent RESMGR from continuing, but you won't be able to run
diagnostics.
Load the Diagnostic program, then rerun RESMGR.
RSM3009 This function not allowed with current account capability.
You tried to perform a RESMGR function that is not available to you. The
function requires SM or NM capabilities.
Perform the function based on your logon account capabilities.
RSM3010 Too many parameters.
Your entry may have been a combination of command mode and function key
instructions, or you may have typed too many parameters in a command
string.
Perform the function using either the command mode or function key
interface. Command mode lets you fully specify all parameters in one
string, and the function key interface prompts for each parameter. Refer
to Chapter 11, "Resource Manager Commands," or type HELP command to
review the command syntax.
RSM3011 - RSM3100
Not used.
RSM3101 There is activity on the network. Tables not released.
You tried to release the tables while there were users on the network.
Wait until there is no activity on the network, then release the
tables.
RSM3102 Unable to purge the share file.
Your attempt to purge the share file was unsuccessful because of an MPE
file system error. Although it is unlikely, it is possible that activity
on the network is preventing the purge.
First, choose ~~Share Status f5 to be sure no users gained access to
the network between the time you released the tables and your attempt to
purge the share file. Next, check security on the share file
(PDSHARE.PPC.SYS) and release it if necessary. If neither of these
actions solves the problem, contact your HP representative.
RSM3103 Share file not purged. Release the tables and try again.
You tried to purge the share file without first releasing the tables.
Release the tables, then purge the share file.
RSM3104 Unable to purge the configuration file.
Your attempt to purge the configuration file was unsuccessful because of
an MPE file system error.
Check security on the configuration file (PDCONFIG.PPC.SYS) and release
it if necessary. If this doesn't solve the problem, contact your HP
representative.
RSM3105 This function not allowed with current account capability.
You tried to perform a RESMGR System area function that is not available
to you. You must have SM or NM capability to do System area tasks.
Perform the function based on your logon account capabilities.
RSM3106 - RSM3200
Not used.
RSM3201 Illegal function - internal error.
This is an internal HP 3000 error caused by an out-of-phase condition
between the system SL and RESMGR.
Note the steps you were performing when the error occurred and contact
your HP representative.
RSM3202 Illegal function - internal error.
This is an internal HP 3000 error caused by an out-of-phase condition
between the system SL and RESMGR.
Note the steps you were performing when the error occurred and contact
your HP representative.
RSM3203 Configuration value out of range.
The configuration value you typed is not within the legal limits.
Type a legal value. Refer to Table 10-1 "MPE iX Shared Disc
Configuration Parameters," for a list of the minimum, maximum, and
default configuration values.
RSM3204 This function not allowed with current account capability.
You tried to perform a RESMGR Configuration area function that is
unavailable to you. You must have SM or NM capability to do
Configuration tasks.
Perform RESMGR functions in accordance with your logon account
capabilities.
RSM3205 Disc error on the configuration file.
RESMGR has encountered an MPE file system error while accessing its
configuration file (PDCONFIG.PPC.SYS).
Read the MPE file system error message(s) for more information.
RSM3206
Not used.
RSM3207 Table limit exceeded, lower CONNECTS or OPEN FILES value.
You exceeded the table limit (44 connects, 256 open files).
Lower the number of connections or the number of open files.
RSM3208 Table limit exceeded, lower SHARED FILES or LOCKED FILES value.
You exceeded the table limit (447 shared files, 1000 locked files).
These two settings are interdependent. As you increase the number of
shared files allowed, decrease the number of locked files (or vice
versa).
Lower the number of shared files or locked files.
RSM3209 Too many parameters for this command.
You typed more parameters than are valid for this configuration command.
Retype the command. Refer to Chapter 11, "Resource Manager Commands,"
or type HELP command to review command syntax.
RSM3210 Entry inconsistent with configuration data. Value accepted.
Your configuration entry is inconsistent with configuration value rules.
Refer to the Chapter 10, "Advanced Resource Manager Functions," for an
explanation of the configuration values.
RSM3211 Numeric data expected.
You typed non-numeric data where numbers were expected. Neither alpha
nor special characters are allowed here.
Retype the data with numeric values only.
RSM3212 - RSM3300
Not used.
RSM3301 AM capability required to perform this function.
You tried to perform a function that is unavailable to you.
Perform the function based on your logon MPE capabilities.
RSM3302 Unable to create shared disc in groupname.
Your attempt to create a shared disc was unsuccessful due to a file
system error such as the shared disc already exists, insufficient disc
space, etc.
Read the MPE file system error for more information.
RSM3303 Unable to delete shared disc in groupname.
The disc you are trying to delete may be secured, or it may not exist.
First verify that you are not trying to delete a nonexistent shared
disc. If the disc exists, you may not have the MPE capabilities to
delete it.
RSM3304
Not used.
RSM3305 Too many parameters for this command.
You typed more parameters than are necessary for this RESMGR command.
Retype the command. Refer to Chapter 11, "Resource Manager Commands,"
or type HELP command to review command syntax.
RSM3306 Invalid delimiter. Valid delimiters are delimiters
You typed an invalid command string delimiter. Valid delimiters are
commas and spaces.
Retype the command with valid delimiters.
RSM3307 Invalid group name.
RESMGR could not find the group you specified. It may be non-existent,
you may have typed it incorrectly, or you may have typed both the group
and account names (the account name is not a valid entry).
Retype the group name.
RSM3308 Can't understand that command. Try again.
RESMGR was unable to parse the command.
Retype the command, verifying the syntax. Refer to the online help for
help with command syntax.
RSM3309 Create failed. There is already a shared disc in groupname
Be sure you have the correct group name for the disc you want to
create.
RSM3310 No shared disc found.
RESMGR can't find a shared disc in the group you specified.
Be sure you have the correct group name for the disc you are trying to
access. Make sure you are logged in to the correct account.
RSM3311
Not used.
RSM3312 Shared disc is in use.
You tried to delete a shared disc while there are active shares to it.
Be sure you are not trying to delete the wrong disc. If it is the
correct disc, wait until it is not in use to delete it.
RSM3313 Request cancelled.
RSM3314 - RSM3500
Not used.
RSM3501 Too many parameters for this command.
You typed more parameters in this SHARE command than the program
expected.
Retype the command. Refer to the online help for help with command
syntax.
RSM3502 Illegal share function specified.
RESMGR did not recognize the specififed SHARE command.
Be sure the command name and syntax are correct and retype the command.
Refer to the online help for help with command syntax.
RSM3503 Invalid password.
The password you typed is incorrect. It is an error to type a password
incorrectly, to type a password when there is none, and to omit typing a
password when one is required.
Attempt the Delete function again, specifying the correct password.
Use the SHARE STATUS PASSWORD command to determine the correct password.
Refer to the online help for help with command syntax.
RSM3504 This function not allowed with current account capability.
You tried to perform a RESMGR function that is unavailable to you.
Perform the function based on your MPE capabilities.
RSM3505 Connection path does not exist.
Either the specified path has no shared disc associated with it, or the
group and/or account don't exist.
Check the status of the disc you expected to be associated with this
share. Deleting a disc does not remove its shares. Create the disc if
necessary, or use another.
RSM3506 Disc error on the share file.
RESMGR has encountered an MPE file system error while accessing its share
configuration file (PDSHARE.PPC.SYS).
Read the MPE error message accompanying this message.
RSM3507 Invalid connection path.
You typed the pathname incorrectly, or, the VDROOT file may not exist.
Make sure you typed the correct pathname, and verify that the VDROOT
file exists for the share.
RSM3508 Duplicate sharename.
The sharename you typed already exists.
Select a different sharename for this path, or delete the previous one.
RSM3509 Invalid sharename.
RESMGR does not understand the sharename you typed.
Type the sharename again; be sure the format is correct. Sharename
syntax is the same as pathname syntax.
RSM3510
Not used.
RSM3511 No shares with those characteristics with your logon
capability.
RESMGR found no shares that match the parameters you specified, or there
are no shares matching the parameters that you are able to access.
Retype the command.
RSM3512
Not used.
RSM3513 Unable to lock share file.
RESMGR encountered an MPE file system error while trying to lock the
share file for exclusive use.
Try performing the function again.
RSM3514 Unable to unlock share file.
RESMGR encountered an MPE file system error while trying to unlock the
share file after exclusive use.
Try performing the function again. If you get the same error, check
the MPE error message.
RSM3515 There is activity on the requested sharename.
You tried to delete the share while it was being used.
Wait until there is no activity, then perform the delete.
RSM3516 No shared disc in the specified group and account.
There is no shared disc in the group and account specified.
Either there is no shared disc in the group and account, or you
specified an incorrect group or account.
RSM3517 Attempting to share a print device as a disc.
Your command to share a disc included the name of a configured printer as
the sharename.
Use an appropriate disc sharename in your command. If you are trying
to share a printer, check your command syntax and be sure it is correct
for printer sharing.
RSM3518 Invalid index.
This is an internal HP 3000 error.
This indicates a serious problem and may require contacting your HP
representative.
RSM3519 The device class specified does not exist.
The device class entered is not a configured MPE device.
Use SYSGEN to configure the device class.
RSM3520 Invalid share request.
RESMGR could not understand your share request.
Retype the command, being sure the syntax and format are correct.
RSM3521 Not enough parameters for this command.
RESMGR expected more parameters in the command than you typed.
Retype the command, being sure you type all the parameters required to
perform the function, or use the function labels and automatic program
prompts.
RSM3522 Invalid access (permission).
You typed a permission code other than R (read), W (write) or C (create).
Type the permission code correctly.
RSM3523 - RSM3524
Not used.
RSM3525 The command has been cancelled.
RSM3526 The password is too long.
Passwords can be a maximum of eight characters.
Retype the password, using eight characters or less.
RSM3527 Illegal characters in password.
You typed characters that cannot be used in a password (/\*).
Retype the password, eliminating illegal characters.
RSM3528 Expected numeric data.
You typed non-numeric data where numbers were expected. Neither alpha
nor special characters are allowed.
Retype the data with numeric values only.
RSM3529 The specified file does not exist.
You typed a formatter filename that does not exist.
Make sure you typed the filename correctly. If you haven't created the
formatter file yet, be sure you do so before you send documents to the
formatter.
RSM3530 Unable to get file information.
RESMGR found the formatter of environment file but can't read it.
Create the file again.
RSM3531 The specified file is not a program file.
The formatter filename you typed is not a program file.
Make sure the formatter file is a program file. Type this command:
LISTF filename,2
RSM3532 The specified file is not a valid environment file.
Type a valid environment filename, such as ELITE.HPENV.SYS.
RSM3533 The value specified is out of range.
The value you typed for job input, job output, or document output is out
of range.
Type a valid value.
RSM3534 The time specified is invalid.
You typed an invalid time for the formatter to execute.
Type a valid time in 24 hour clock format (nnnn). For example, 0000 =
midnight; 0100 = 1:00 a.m., etc.
RSM3535 SM or NM capabilities are required.
You tried to perform a RESMGR function that is not available to you. You
must have SM or NM capability to perform this function.
Perform the function based on your MPE logon capabilities.
RSM3536 The device specified is not a spooled device.
The device class needs to be a spooled device.
Configure the printer as a spooled device.
RSM3537 Resource Sharing system error encountered.
Resource Sharing encountered a system error while trying to verify that
the device specified is valid.
Note the steps you were performing when the error occured (including
any error messages), then contact your HP representative.
RSM3538 Sharename/device class is too long.
The sharename or device class entered has more than eight characters.
Reenter the command, ensuring the sharename and device class have no
more than eight characters each.
RSM3539 Sharename, device class or password is too long.
The sharename, device class, or password entered has more than eight
characters.
Reenter the command, ensuring the sharename, device class, and password
have no more than eight characters each.
RSM3540 - RSM6204
Not used.
RSM6205 ERROR - Internal failure in program. Procedure name, Error
Parm # number
RESMGR has encountered an error condition it can't interpret.
Record the information on the screen and contact your HP
representative.
RSM6206 ERROR - Shared disc not on this tape.
RESMGR can't find the shared disc root directory, which is required for
the recover function.
Be sure you have the right tape mounted. If the tape does not contain
the root directory, you will not be able to recover shared disc files
from it.
RSM6207 ERROR - Unable to open disc root file. Error # number
RESMGR has encountered an error while attempting to open the VDROOT file
to your shared disc.
Read the MPE error message for more information.
RSM6208 WARNING - Partial Store tape; some files may not be on tape or
"orphan" files present.
The recover function found more recoverable files on tape than exist on
the shared disc.
This is a partial store tape. Because the DOS names of the extra files
are unknown to the recovery function, those files are not recoverable.
RSM6209 ERROR - No files match the pathname pattern(s)
None of the files on the shared disc match the patterns you typed for
backup.
Verify your pattern entry and retype, if necessary. If the patterns
are correct, verify that you typed the right sharename, and that the
correct tape is mounted.
RSM6210
Not used.
RSM6211 WARNING - Unable to open catalog. Default used.
The message catalog corresponding to your user language ID could not be
opened. RESMGR used the message catalog corresponding to the system
language ID, if it was available. Otherwise, the native language of the
system is being used.
Check that your user language ID is set properly. Then make sure a
message catalog for this language exists.
RSM6212 ERROR - Disc in use. Backup/Recover aborted.
The shared disc you are trying to back up or recover is in use.
Make sure the shared disc is not in use before trying to back up or
recover files.
RSM6213 Program terminated due to errors
Read the other messages to determine the problem.
RSM6214 - RSM6219
Not used.
RSM6220 ERROR - Tape Device is unavailable, FSERR #number
The operator typed in a 0 (zero) in response to the tape request.
Reissue the request.
RSM6221 ERROR - Files on tape not in alphabetical order.
The files on the tape are not in alphabetical order, so RESMGR can't
recover them.
This is an irrecoverable error. It is probable that the filename
entries for this backup tape were typed individually, at random and out
of alphabetical order.
RSM6222 ERROR - Tape is not a STORE format tape
The tape mounted is not in the Store format - it is the wrong tape.
Reissue the recovery request, and ask the operator to mount the correct
tape.
RSM6223 ERROR - Irrecoverable tape error FSERR #number
This error is returned from MPE if there is a file system or attach I/O
error from which it can't recover.
Verify that the tape drive and tape volume are correct. This error may
indicate a problem opening the tape; the error returned is given by the
FCHECK MPE intrinsic.
RSM6224 - RSM6226
Not used.
RSM6227 WARNING - $null tape specified, STORE ignored
This message tells you that there will be no backup tape generated
because you specified a $null tape.
RSM6228 ERROR - STORE program could not back up files
This message is returned from the HP 3000, and tells you that the STORE
program was unable to back up some or all of your shared disc files.
Check the messages on your screen or printout to see which files
weren't backed up. Try using the MPE STORE program to back up the groups
and accounts containing your shared discs.
RSM6229 ERROR - Unsupported STORE tape format
Your version of the STORE program is not supported with this release of
Resource Sharing.
Install a later version of the STORE program.
RSM6230 ERROR - User lacks non-shareable device (ND) capability.
You do not have the account capability needed to use the tape drive.
RSM6231 - RSM6234
Not used.
RSM6235 ERROR - No data typed.
You need to type in parameters for the backup or recovery to take place.
This is an informational message. It is followed on your screen by
help text explaining the format of the backup or recovery. Follow the
instructions and type in the backup or recover command.
RSM6236 ERROR - Invalid pathname syntax. Too many "."s
Your pathnames pattern contained more than one period (.) delimiter in a
row.
Type the pattern correctly.
RSM6237 ERROR - Pathname too long
One or more segments of the pathname you typed in contains too many
characters.
Type the pathname correctly. Filenames can be up to eight characters,
and filename extensions can be up three characters.
RSM6238 ERROR - Invalid pathname syntax. Empty pathname component.
One of the components of the pathname is missing.
Type the pathname correctly.
RSM6239 ERROR - Unexpected character found (expected ",")
RESMGR expected a comma as the separator between pathname patterns, and
found some other character.
Type the patterns correctly. Note that a blank between patterns is
considered an invalid character, as is any character other than a comma.
RSM6240
Not used.
RSM6241 ERROR - Unexpected character found (expected end-of-line)
RESMGR expected a carriage return at the end of the info string, and
found an invalid symbol instead.
Retype the command.
RSM6242
Not used.
RSM6243 ERROR - No pathnames typed
You didn't give the program a pathname pattern to follow when selecting
files to back up.
Type in a pathname pattern.
RSM6244 ERROR - Unknown option; expected one of the following:
"BACKUP", "RECOVER"
You did not use a valid command such as RECOVER or BACKUP.
Retype the command, using a valid option.
RSM6245 ERROR - Invalid character in pathname
The pathname pattern contained an invalid character.
Type in a valid pathname pattern.
RSM6246 ERROR - Can't open redirect file, FSERR# number
The MPE file system couldn't open the redirect file containing your
patterns.
Verify that the redirect filename you specified is correct, then retype
the backup request.
RSM6247 ERROR - Can't access redirect file, FSERR # number
MPE was unable to read the redirect file containing your patterns.
Check for a security violation (group/account capabilities), then retry
the backup. If you continue to get this error, note the steps you were
performing when the error occurred and contact your HP representative.
RSM6248 This function not allowed with current account capability.
You do not have the account capability needed to use this function.
RSM6249 - RSM6254
Not used.
RSM6255 ERROR - PC Connection to sharename or physical path failed;
error #number
RESMGR cannot recover files because it cannot connect to the shared disc.
See accompanying messages for more information.
RSM6256 WARNING - Recovery of filename failed due to previous errors
Check the error message(s) preceding this message for more information.
If you can't solve the problem, note the steps you performed when the
problem occurred and contact your HP representative.
RSM6257 WARNING - Recovery of filename failed, PC Create error number
RESMGR's Recover function was unable to create a file or directory on the
shared disc.
See the accompanying messages for more information.
RSM6258
Not used.
RSM6259 WARNING - Recovery of filename failed, PC Close error number
RESMGR was unable to close a file after recovering it.
See accompanying messages for more information.
RSM6260
Not used.
RSM6261 WARNING - Recovery of filename failed, PC Write error number
RESMGR was unable to write to a file during recovery.
See accompanying messages for more information.
RSM6262 - RSM6269
Not used.
RSM6270 nnn files selected for recovery
This is a status message, telling you the number of files selected out of
the total files on the tape.
RSM6271 nnn files selected for backup
This is a status message, telling you the number of files selected for
backup from your shared disc.
RSM6272 Recovering filename (number bytes)
RSM6273 Recovering directoryname
RSM6274 Recovering directoryname
RSM6275 filename selected (number bytes)
RSM6276 directoryname selected.
RSM6277 nnn warning(s) displayed
This is a status message, telling you the number of warning messages
given during the backup or recovery operation. The warnings give you
information about unusual but not fatal conditions encountered.
Check the warning messages. If they have rolled off the screen and out
of terminal memory, you will be unable to see them. For this reason,
it's a good idea to route the display to a printer using a file equation
(see Chapter 9, "Managing Shared Discs").
RSM6278 nnn file(s) recovered
RSM6279 nnn file(s) NOT recovered
Check the warning messages on your screen or printout to determine why
these files were not recovered.
RSM6280 nnn directory file(s) created
RSM6281 Output listing redirected to file filename
You have redirected the output to the file listed.
RSM6282 - RSM6284
Not used.
RSM6285 Please mount previous tape volume (number) on LDEV #number
RSM6286 Please mount next tape volume (number) on LDEV #number
RSM6287 Incorrect tape volume (number) mounted on LDEV # number
This message displays on the system console when a multi-volume tape set
is used for recovery. The operator mounted the wrong volume. The next
message that displays requests the correct volume.
RSM6288 Accessing tape device
RSM6289 - RSM6294
Not used.
RSM6295 Currently using redirect file filename
This is an informational message, telling you the redirect filename where
an error occurred. The line displayed below this message shows you the
line in the file with the error.
Correct the error in the redirect file and retry the backup.
RSM 6296 - RSM6303
Not used.
RSM6304 A sharename is required, please retype
You must type the sharename of the shared disc you want to back up or
recover.
RSM6305 SM, AM or OP capabilities are required for Physical Path
You are trying to back up or recover files by typing the physical path to
the shared disc files you want to use, and you do not have the correct
capabilities.
Type the sharename of the shared disc, rather than the physical path.
RSM6306 Request cancelled
You cancelled the backup or recover request.
RSM6307
Not used.
RSM6308 Could not create process "PDBAKUP.PPC.SYS"; Error Code number
You are trying to back up a file, and RESMGR cannot find the PDBAKUP
program. This is a Create Process error.
Make sure you have a file called PDBAKUP.PPC.SYS. Try running the
backup program by typing RUN PDBAKUP.PPC.SYS. If the error persists, note
the error message and contact your HP representative.
RSM6309 - RSM7000
Not used.
RSM7001 Invalid password specified.
The password you typed is incorrect.
Type in the correct password.
RSM7002 Undefined connection encountered
You typed an invalid sharename for a disc or device.
Make sure you typed the sharename correctly.
RSM7003 Number of connections exceeds configuration limits
Resource Sharing has reached the maximum number of configured active
connections.
You can't add more connections unless the configuration limit is
raised.
RSM7004 Illegal request, an unknown tree ID was specified
This is an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7005 MS-DOS file not found, or invalid file name
The program couldn't find the file you specified.
Be sure you are accessing the correct disc. Verify the filename and
retype it.
RSM7006 The path reference given does not exist
RESMGR could not find the specified pathname.
Verify the pathname, then retype it.
RSM7007 Insufficient internal table space
Resource Sharing couldn't find needed space.
Check RESMGR's configuration limits and raise them if needed.
RSM7008 The user does not have sufficient capabilities
The sharename does not have the correct capabilities (RWC) for the task
you are trying to perform. For example, you may be trying to recover
files on a shared disc with a sharename assigned Read capability.
Use a sharename with the correct capabilities.
RSM7009 File is already in use
The shared disc you are trying to access is already in use.
RSM7010 File already exists
You are trying to create a file on the shared disc that already exists.
RSM7011 A file handle was specified that does not exist
Resource Sharing has an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7012 The target file does not support the access mode requested
The program specified an access mode that is invalid for the target file.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7013 An end-of-file during a read was encountered
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7014 A read attempt beyond the end-of-file was encountered
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7015 The operation conflicts with an existing lock
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7016 The physical end-of-file has been encountered
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7017 The directory specified does not exist
The specified directory could not be found.
Verify the directory name, then retype it.
RSM7018
Not used.
RSM7019 The source path reference can not be found
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7020 The destination path reference can not be found
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7021 The source file reference can not be found
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7022 The destination file already exists
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7023 The range-lock can not be found
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7024 The directory search has been completed with no entries found
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7025 An MPE file system error has been encountered
MPE has returned a file system error to the program, and can't continue.
Read the MPE error message for more information.
RSM7026 Insufficient MPE disc space to complete operation
Check the availability of disc space on your system, account, and
group.
RSM7027 An internal directory error has been encountered
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7028 The calling process does not have "MR" capabilities
The program you are running does not have sufficient MPE capabilities for
accessing shared discs.
Contact your HP representative.
RSM7029 An internal Resource Sharing error has occurred
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7030 An invalid syntax was specified
You typed the command incorrectly.
Retype the command, using the correct syntax. Type HELP command to
review the syntax.
RSM7031 Merge pending, the reference file is currently unavailable
The file is open for another user, or it was not closed properly by the
last user.
Try again.
RSM7032 The specified directory already exists
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7033 The specified directory is not empty
You are trying to remove a directory that contains files.
Delete the files from the directory, then remove the directory.
RSM7034 An invalid attribute was specified
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7035 The operation does not support the specified mode
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7036 - RSM7037
Not used.
RSM7038 A unique temporary file could not be generated (name conflict)
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7039 The operation is inconsistent with the previous connection
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7040 Path too long
The pathname to thte file you are creating is longer than the maximum
allowed.
Shorten the pathname by reorganizing and/or renaming your
subdirectories (that is, use shorter directory names or fewer
subdirectories).
RSM7041 Invalid access mode
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7042 Invalid sharing mode
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7043 Read only file; write access denied
You tried to write to a file that has read only access.
Make a copy of the file and then modify the copy with write access.
RSM7044
Not used.
RSM7045 Negative byte pointer
Resource Sharing has encountered an internal error.
Note the steps you were performing when the error occurred, then
contact your HP representative.
RSM7046 File has read only access, access denied
You tried to delete a file that has Read Only access.
Change the file to Read/Write access.
RSM7047 "SM" capabilities are required
This function requires System Manager (SM) capability.
RSM7048 "AM" capabilities are required
This function requires Account Manager (AM) capability.
RSM7049
Not used.
RSM7050 Null lock
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7051 Record size too big
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7052 Negative count
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7053
Not used.
RSM7054 File is a directory, not a data file
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7055 File is a data file, not a directory
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7056 Invalid directory name
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7057 No shared disc
The shared disc does not exist.
Use RESMGR to create a shared disc.
RSM7058 The specified class does not contain any devices.
Internal error.
Note the steps you were performing when the error occured, then contact
your HP representative.
RSM7059 The connection has files open.
You attempted to disconnect from a sharename that has files open.
Close the files before disconnecting.
RSM7060 Attempted to exceed maximum number of shared disc files.
You have reached the maximum number of files allowed in a shared disc.
The maximum number of files in a shared disc is 30000.
Delete any unused files.