HP 3000 Manuals HP 3000 Manuals
Installation Instructions
Use the appropriate sections below depending on whether you are
installing from an MPE SUBSYS tape or updating from a software patch.
Installing from an MPE SUBSYS tape
If you are installing or updating the HP Performance Collection Software
on your HP 3000 from an MPE SUBSYS tape, perform the instructions in this
topic.
MPE/iX systems.
1. Read chapter 1, "Read Me First", in the HP 3000 MPE/iX
Installation, Update, and Add-On Manual, part number 36123-90001.
2. If you are updating your MPE/iX operating system and HP
Performance Collection Software at the same time, follow the
instructions in chapter 2 titled "Updating MPE/iX".
3. If you are installing or updating only HP Performance Collection
Software and not the MPE/iX operating system, follow the
instructions in chapter 3, "Adding On Purchased Products - SUBSYS
Only".
4. After completing the AUTOINST installation, continue in this
manual at the "Completing the HP 3000 Installation" section.
MPE V systems.
1. If you are updating the MPE V operating system and HP Performance
Collection Software at the same time, follow the instructions in
the HP 3000 Software Update Manual, part number 32033-90036.
2. If you are only updating HP Performance Collection Software and
not the MPE V operating system, follow the instructions in the HP
3000 Software Add-On Manual, part number 32033-90048.
3. After completing the AUTOINST installation, continue in this
manual at the "Completing the HP 3000 Installation" section.
Updating from a Software Patch
If you are updating an older version of HP Performance Collection
Software on an MPE/iX system, you can apply a software patch instead of
loading the software from a SUBSYS tape. Ask your HP support
representative for patch LRXHX04, version A or later.
To update an existing version of the collection software on an MPE/iX
system, do the following:
1. Restore the four patch files to the PATCHXL.TELESUP group on your
system.
2. Stream I00HX04A.PATCHXL.TELESUP.
3. When prompted, enter the name of a group in the SYS account where
a copy of the current SCOPE collector files can be saved. If the
installation fails, copy the files in this group back into the
SCOPE group.
4. When the installation is complete, the installation program
streams JCONFJOB.NET.SYS. If the stream fails because of an
invalid password, manually stream JCONFJOB.NET.SYS at a convenient
time.
5. Before you can use the new data communication servers, you must
stop and restart the network with the NSCONTROL and NETCONTROL
commands.
If the installation completes successfully, the SCOPE collector files
saved earlier are purged.
After completing the steps above, continue with the "Completing the HP
3000 Installation" section later in this chapter.
Patch Installation Error Messages
If the patch installation in not successful, you may get one of the
following error messages. A suggested remedy is listed when possible.
LaserRX/MPE install error: 1
This version of MPE/iX is not supported by patch LRXHX04.
The patch requires MPE/iX version 4.0 or later.
To check your version of MPE/iX, use the SHOWME command. The second line
should show a release version of B.40.00 or higher. If it does not, you
cannot update your software with the patch.
LaserRX/MPE install error: 2
A variable needed for patch LRXHX04 could not be retrieved or created.
This error is unlikely, and indicates that the installation program
encountered an unexpected condition and could not continue.
Report this error and the message immediately preceding this error to
your HP support representative.
LaserRX/MPE install error: 3
You currently have a trial version of HP LaserRX/MPE installed. You must
purchase the software.
The HP LaserRX/MPE collection software is available on a trial basis.
The trial copy may only be installed once on a system. Once it is
installed, you must contact your HP representative to enable your system
so that the purchased HP LaserRX/MPE software can be installed.
Note: Restarting your system will not enable the software for
installation.
LaserRX/MPE install error: 4
You currently do not have the HP LaserRX/MPE product installed on your
system.
If you have purchased the product, you must install the product using
AUTOINST along with an MPE/iX sybsys tape for MPE/iX release B.40.00 or
later.
LaserRX/MPE install error: 6
P01HX04A.PATCHXL.TELESUP is missing.
Restore the file from the tape containing patch LRXHX04.
LaserRX/MPE install error: 7
P02HX04A.PATCHXL.TELESUP is missing.
Restore the file from the tape containing patch LRXHX04.
LaserRX/MPE install error: 8
Unable to unload all necessary files into SCOPE.SYS group.
The program that loads files into the SCOPE.SYS group encountered an
error. RESTORE the four LRXHX04A patch files into PATCHXL.TELESUP and
try again.
If the second attempt is also unsuccessful, contact your HP support
representative for assistance.
LaserRX/MPE install error: 9
No CASE FOR THIS ERROR...Error = XX
The installation program was not able to successfully unpack the HP
LaserRX/MPE files. RESTORE the four LRXHX04A patch files into
PATCHXL.TELESUP and try again.
If the second attempt is also unsuccessful, contact your HP support
representative for assistance.
LaserRX/MPE install error: 10
The following programs that need to be replaced to install LRXHX04 A are
in use: XXXX.XX.XXX is in use.
Use the procedures listed in the "Preparation" section to deactivate a
server or the collection software if any of the following files are
listed:
SCOPEXL.SCOPE.SYS
HCSERVER.PPC.SYS
HCS.PPC.SYS
XL.SCOPE.SYS
IASQL@.PPC.SYS
If the file EXTRACT.SCOPE.SYS is listed, find out which users are running
the EXTRACT program, and have them exit.
LaserRX/MPE install error: 11
The operator has requested to QUIT the installation of LRXHX04 A.
The operator elected to stop installing the patch when prompted for the
group where the old collection software could be saved.
LaserRX/MPE install error: 12
Only 4 "other" errors allowed on GROUP.
The group name that the operator supplied as the group where the SCOPE
collector files could be saved was not valid.
Determine a syntactically correct group name that does not already exist
in the SYS account, and stream I00HX04A.PATCHXL.TELESUP again.
LaserRX/MPE install error: 13
An error has occurred attempting to execute the following command:
Command_Name_Here
An error has occurred trying to create the group named by the operator as
the group where a copy of the SCOPE collector files could be saved. The
name of the command that failed is printed with the error message. Enter
the command interactively to determine the error number.
Determine a syntactically correct group name that does not already exist
in the SYS account, and stream I00HX04A.PATCHXL.TELESUP again.
If the second attempt is unsuccessful, contact your HP representative for
assistance.