HP 3000 Manuals HP 3000 Manuals
Chapter 7 Network Services Information Messages
These messages, displayed on $STDLIST during the execution of a command,
give the user information about the environment(s) affected by the
command. They are held in CATALOG.PUB.SYS, message set 16 (DS set). No
action is required for these messages.
500 MESSAGE ENVIRONMENT envum: envid.
CAUSE The defined or affected environment has been
assigned an environment number envum and
environment ID envid. Envid will be fully
qualified with domain and organization names.
The node name for the environment is the same as
the environment ID. If the DSLINE specified a
generic environment ID, there will be one
ENVIRONMENT message displayed for each affected
environment.
ACTION This is an informative message.
501 MESSAGE ENVIRONMENT envum: envid=nodename.
CAUSE The defined or affected environment has been
assigned an environment number envum and
environment ID envid.
Envid will be fully qualified with domain and
organization names. The environment is on
nodename, which is different from envid. If the
node is an NS node, nodename is fully qualified.
ACTION This is an informative message.
502 MESSAGE NO ENVIRONMENTS.
CAUSE A DSLINE with a generic environment ID was
executed, and there were no environments with an
ID that matched the generic ID. The DSLINE then
has no effect.
ACTION Reissue the command with a correct environment
ID.
503 MESSAGE ABORT REMOTE SESSION ON envid?
CAUSE A DSLINE CLOSE was issued for an environment
that has a Virtual Terminal remote session.
Envid is the environment ID for the environment.
This message expects a YES (or Y), or NO (or N)
response from the user.
ACTION Enter YES to abort the remote session and close
the environment. Enter NO, to retain the remote
session and keep the environment open. If a
DSLINE CLOSE with a generic environment is
executed, an ABORT REMOTE SESSION message is
displayed for each matching environment with a
remote session.
504 MESSAGE PLEASE ANSWER YES OR NO:
CAUSE A question (such as ABORT REMOTE SESSION) has
been asked, and the user entered a response
other than YES or NO. This prompt is displayed
until the user replies YES, Y, No, or N.
ACTION Enter either YES or NO in response to this
message.
505 MESSAGE KILL RPM PROCESS ON envid?
CAUSE A DSLINE CLOSE has been issued for an
environment that includes an RPM-created
process. Envid is the environment ID for the
environment.
ACTION Enter YES (or Y) to issue an RPMKILL for the
process, and to close the environment. Enter NO
to retain the RPM process and to keep the
environment open. If DSLINE CLOSE is issued
with a generic environment, a KILL RPM PROCESS
message is displayed for each matching
environment with an RPM process.
506 MESSAGE GENERIC ENVIRONMENT envid.
CAUSE A generic environment has been established by a
DSLINE for the specified envid pattern, which
includes wild card characters @, #, and/or ?.
All existing environments with an ID that
matches the generic envid acquire the
characteristics specified in the DSLINE command.
(The affected environments will be listed.) In
addition, all future environments with an ID
that matches the generic pattern will assume the
DSLINE options as defaults. (These default
options can be explicitly overridden, though).
The generic environment remains in effect until
it is reset by a DSLINE RESET command.
ACTION This is an informative message.
507 MESSAGE NO GENERIC ENVIRONMENTS.
CAUSE For a DSLINE or DSLINE SHOW, there are no
currently defined generic environments with an
ID that matches the specified pattern.
ACTION Specify an environment with a valid ID.
508 MESSAGE REMOTE SESSION ABORTED.
CAUSE During a DSLINE CLOSE, the user specified YES to
the ABORT REMOTE SESSION ON envid? message.
The remote session on the specified environment
was aborted.
This is an informative message.
510 MESSAGE TRACE FILE FOR ALL SERVICES TO envid IS
filename.
CAUSE A DSLINE with a TRACE=ON or TRACE=OFF option was
executed. These messages indicate which service
to what environment is being (or has been)
traced, and the fully qualified name of the
trace file. One TRACE message is displayed for
each TRACE option in the command. If a DSLINE
with a generic environment ID turns tracing on
or off for a set of environments, the TRACE FILE
FOR ALL SERVICES TO envid IS filename message is
displayed for each environment.
ACTION This is an informative message.
511 MESSAGE TRACE FILE FOR VT TO envid IS filename.
CAUSE A DSLINE with a TRACE=ON or TRACE=OFF option was
executed. These messages indicate which service
to what environment is being (or has been)
traced, and the fully qualified name of the
trace file. One TRACE message is displayed for
each TRACE option in the command. If a DSLINE
with a generic environment ID turns tracing on
or off for a set of environments, the TRACE FILE
FOR ALL SERVICES TO envid IS filename message is
displayed for each environment.
ACTION This is an informative message.
512 MESSAGE TRACE FILE FOR NFT TO envid IS filename.
CAUSE A DSLINE with a TRACE=ON or TRACE=OFF option was
executed. These messages indicate which service
to what environment is being (or has been)
traced, and the fully qualified name of the
trace file. One TRACE message is displayed for
each TRACE option in the command. If a DSLINE
with a generic environment ID turns tracing on
or off for a set of environments, the TRACE FILE
FOR ALL SERVICES TO envid IS filename message is
displayed for each environment.
ACTION This is an informative message.
513 MESSAGE TRACE FILE FOR RFA TO envid IS filename.
CAUSE A DSLINE with a TRACE=ON or TRACE=OFF option was
executed. These messages indicate which service
to what environment is being (or has been)
traced, and the fully qualified name of the
trace file. One TRACE message is displayed for
each TRACE option in the command. If a DSLINE
with a generic environment ID turns tracing on
or off for a set of environments, the TRACE FILE
FOR ALL SERVICES TO envid IS filename message is
displayed for each environment.
ACTION This is an informative message.
514 MESSAGE TRACE FILE FOR RDBA TO envid IS filename.
CAUSE A DSLINE with a TRACE=ON or TRACE=OFF option was
executed. These messages indicate which service
to what environment is being (or has been)
traced, and the fully qualified name of the
trace file. One TRACE message is displayed for
each TRACE option in the command. If a DSLINE
with a generic environment ID turns tracing on
or off for a set of environments, the TRACE FILE
FOR ALL SERVICES TO envid IS filename message is
displayed for each environment.
ACTION This is an informative message.
515 MESSAGE TRACE FILE FOR RPM TO envid IS filename.
CAUSE A DSLINE with a TRACE=ON or TRACE=OFF option has
been executed. These messages indicate which
service to what environment is being (or has
been) traced, and the fully qualified name of
the trace file. There will be one TRACE message
for each TRACE option in the command. If a
DSLINE with a generic environment ID turns
tracing on or off for a set of environments,
there will be one TRACE message for each
environment.
ACTION This is an informative message.
516 MESSAGE TRACE FILE FOR PTOP TO envid IS filename.
CAUSE A DSLINE with a TRACE=ON or TRACE=OFF option was
executed. These messages indicate which service
to what environment is being (or has been)
traced, and the fully qualified name of the
trace file. One TRACE message is displayed for
each TRACE option in the command. If a DSLINE
with a generic environment ID turns tracing on
or off for a set of environments, the TRACE FILE
FOR ALL SERVICES TO envid IS filename message is
displayed for each environment.
ACTION This is an informative message.