HP 3000 Manuals HP 3000 Manuals
Booting the System
1. Turn the system on. After 5 to 10 minutes of system activity, you
should see a screen similar to the following.
_____________________________________________________________________________
| |
| |
| PDC - Processor Dependent Code |
| Version n.nn |
| (c) Copyright 1990-1992 |
| The Hewlett-Packard Company |
| All rights reserved |
| |
| Total Memory: 256 MB |
| Total Processors: 2 |
| |
| Primary boot path 0/52.0.0.0.0.0.0 |
| 16 means BC 0 in PMB slot 0. |
| 52 means I/O card in HP-PB slot 13. |
| 0 means device ID of 0. |
| |
| Alternate Boot Path: 0/36.1.0.0.0.0.0 |
| Console/Keyboard Path: 0/44.0.0.0.0.0.0 |
| |
| |
_____________________________________________________________________________
Respond to the prompts as shown.
______________________________________________________________
| |
| |
| Continue with primary boot path ([y]/n/<path>) > Y |
| Trying boot path 0/52.0.0.0.0.0.0 ... |
| |
| Booting ... |
| |
| Interact with ISL (Y or N)?> Y |
| |
| MMSAVE Version n.nn |
| DUMPAREA found, save main memory to disc |
| ISL loaded |
| |
| ISL Revision v.uu.ff Month Day, Year |
| |
| ISL> |
| |
______________________________________________________________
If the above screen does not appear within 1 to 2 minutes, reset
your system. Press the CTRL and B keys at the same time. When
you see the CM prompt, connect to the service processor, and
restart system as shown below. Do not respond to "Press any key
within ten seconds to cancel boot with this configuration."
CTRL B
CM>SP
SP>RS
___________________________________________________________________________
| |
| |
| Type Y to confirm your intention to execute this command (y/n): Y |
| |
___________________________________________________________________________
The system will restart and display the Processor Dependent Code
(PDC) screen shown in step 1.
_________________________________________________________________
NOTE The following step applies to all systems except the 9X8LX
and 9X8RS series. If you have a 9X8LX or a 9X8RX, refer to
steps 2a and 2b.
_________________________________________________________________
2. Run IOMAP and print or record the I/O configuration for your
system. Ensure that all peripherals are powered on before you run
IOMAP. This display shows all the path names of the I/O
components. These path names will be added to the SYSGEN I/O
configuration.
ISL> IOMAP
After several progress messages you see the IOMAP banner. Reply N
to "Do you wish to modify any program parameters? [y,n] (n):"
Identify: Loop 1: All I/O components are being.....
Processor Identification:
.
.
.
Type HW SW Revisions Tests
Path Component Names ID Mod Mod Hdwr Firm Avail
----- --------------- ---- --- --- ---- ---- -----
16 Bus Converter (Local Port) 7H 184H CH 0 0
16/0 HP-PB GPIO Card 4H 4H 45H 0 0
16/4 HP-PB SCSI Card 4H 4H 39H 0 0 ST LB
Resetting SCSI Bus (Approx. 10 seconds) ...
SCSI bus address for host adapter is 7
16/4.4.0 HPC1512A DDS tape drive - - - - C600 ST
16/4.5.0 HPC1503A/HPC15208 DDS tape drive - - 4 09 ST
16/5 HP-PB Centronics Parallel Port 5H 4H 3AH 0 0
16/12 20540-60001-002.3-LAN 2H 4H 52H 0 0 ST LB
16/36 HP-PB HPFL Card 4H 4H 41H 0 0 ST
16/36.0 2204FL disc drive - - - - ST
16/36.1 2240FL disc drive - - - - ST
16/36.2 2254HA FL disc drive - - - - ST
16/44 HP-PB Console/LAN Card 2H 54H 50H 0 0 ST LB
System Console is connected to this card
16/52 CIO Channel Adapter 8H 5H 10H 0 0 ST LB
16/52.0 HP-IB card 2H - - 6 2912 ST LB
16/52.0.0 7980 mag tape unit 180H - - - -
16/50 Bus Converter (Remote Port) 1H 7H 102H CH 0
1
18 Bus Converter (Local Port) 7H 184H CH 0 0
28 Memory Controller ( 511 M bytes) 1H 5H 9H 1 0 LB
40 Memory Controller ( 0 M bytes) 1H 5H 9H 1 0 LB
48 Native Processor 0H
56 Native Processor 0H
Identify loop 1 (1H) complete.
Do you want to exit this program and return to ISL? [y,n] (n): Y
IOMAP Exiting.
Switching the Console back to the standard Console Path...
Done.
ISL>
a. For 9X8LS and 9X8RX systems, use the following procedure to
list your system hardware:
i. Type the following at the ISL prompt to get an ODE
prompt:
ISL> ODE
ii. Type the following at the ODE prompt to get a MAPPER
prompt:
ODE> MAPPER
iii. At the MAPPER prompt type:
MAPPER> RUN
b. To exit MAPPER after you modify or accept the information
displayed, you must exit out of MAPPER and ODE to get back
to the ISL prompt. For example:
MAPPER> EXIT
ODE> EXIT
ISL>
3. Start the system from the disk. The configuration for your system
was preloaded at the factory and is configured for the number of
internal disks that you purchased with your system.
ISL> START NORECOVERY
The system displays a series of startup messages, and you are
prompted to confirm the date and time, as shown below.
If the date and time displayed are accurate, enter Y. If not,
enter N, and enter the correct date and time when prompted. Time
must be entered in a 24-hour format (e.g., 5:00 p.m. is entered
as 17:00). Seconds default to 00 if not specified.
______________________________________________________
| |
| |
| MPE/iX launch facility |
| Initialize_genesis - Version ; nnnnnn.nnnn |
| TUE, AUG 11, 1991, 10:20:03 AM (y/n)? Y or N |
| [CMUX_DAM] n n n n |
| Initialize genesis completed |
| |
______________________________________________________
For the next 5-6 minutes, startup and initialization messages are
displayed similar to the screen shown below.
___________________________________________________________
| |
| |
| Initialize genesis completed. |
| Create Console Messages kso completed. |
| Initialize memory manager completed. |
| . |
| . |
| . |
| SESSION Scheduling Initialized |
| Initiate Operator Logon |
| JOB Scheduling Initialized |
| Successfully launched diagnostic monitor process. |
| |
___________________________________________________________
4. Log on to the system.
:HELLO MANAGER.SYS
:STREAMS streams device
:SPOOLER LP;START
5. A default configuration with the internal disks configured was
loaded onto your system at the factory. If you have any external
disks, or other devices, you must change this default configuraton
to include these components. Use SYSGEN to configure them into
your system. If you need additional information on the SYSGEN
utility, please refer to System Startup, Configuration, and
Shutdown Reference Manual (32650-90042).
If you do not have any external disks, or other devices , continue
with "Configuring System Disks Using VOLUTIL"; otherwise follow
the steps below.
:SYSGEN
sysgen>io
6. Print the default configuration to the screen and record the
configuration. This configuration should be changed to represent
the actual configuration as shown on IOMAP.
io>LP
7. Using the commands in io, make any changes to your configuration.
After you have completed the configuration changes, hold the new
configuration and exit:
io>HOLD
io>EXIT
8. Save this new configuration.
sysgen>KEEP CONFIG
Purge old config? YES
sysgen>E
9. Shut down the system by pressing the CTRL and A keys at the same
time, then typing SHUTDOWN as follows:
CTRL A
=SHUTDOWN
_________________________________________________________
| |
| |
| Shutdown of user process begins. (Shut 1) |
| Shutdown of user process begins. (Shut 2) |
| . |
| . |
| . |
| Shutdown of operating system complete. (Shut 6) |
| |
_________________________________________________________
There will be several shutdown messages similar to those shown
above.
10. After the last shutdown message, (Shut 6), restart the system by
pressing the CTRL and B keys at the same time. Respond to the
prompts as shown. You must connect to the service processor
before you can restart the system.
CTRL B
CM>SP
SP>RS
___________________________________________________________________________
| |
| |
| Type Y to confirm your intention to execute this command (y/n): Y |
| |
___________________________________________________________________________
Do not respond to "Press any key within 10 seconds to cancel boot
with this configuration."
If the system does not respond to the CTRL B within ten seconds
power the system off and then back on again, and repeat step 9.
11. Confirm that you want to continue the boot from the primary boot
path. Reply Y to "Interact with ISL?"
12. Start the system from the disk at the ISL> prompt.
ISL>START NORECOVERY
13. Log on to your system.
:HELLO MANAGER.SYS;HIPRI
:STREAMS streams device
:SPOOLER LP;START
A welcome message appears. After the welcome message, you see the
session prompt (:).