HP 3000 Manuals HP 3000 Manuals
"Nonclass" Errors (Cont'd)
Boot Tape Messages
-------------------------------------------------------------
0001 MESSAGE **error** can't open boottype
CAUSE The TAPE command has been issued but SYSGEN cannot
generate a boot tape.
ACTION Check to see the tape is unlabeled, not specially
formatted, and of proper density. check prior file
equations for TAPE commands. Check to be sure the
tape is not damaged.
-------------------------------------------------------------
0013 MESSAGE **error** fail to write boottape label
CAUSE The tape does not meet SYSGEN requirements; the
TAPE command cannot properly format the tape.
ACTION Check to see the tape is unlabeled, not specially
formatted, and of proper density. check prior file
equations for TAPE commands. Check to be sure the
tape is not damaged.
-------------------------------------------------------------
0015 MESSAGE **error** error write file ! onto boottape
CAUSE A file designated in SYSFILEP does not exist, is
corrupted, or there may be a tape problem.
ACTION check system program files through the SYSFILE
configurator SHOW command for spelling and
duplication. Cross-check suspect files through the
command interpreter LISTF command.
-------------------------------------------------------------
0016 MESSAGE **error** can't read file !
CAUSE Usually, a file designated in SYSFILEP does not
exist. Program dies.
ACTION Verify that the file does not exist. Remove the
entry from SYSFILEP through the DSPROG command.
-------------------------------------------------------------
0018 MESSAGE **error** boot tape was opened incorrectly
CAUSE SYSGEN requires a tape of a specific record size
and format on reel-to-reel media. The file
equation for SYSGTAPE changes something it should
not.
ACTION Change the file equation for the proper record size
and format.
-------------------------------------------------------------
0019 MESSAGE **error** can't get boot tape information
CAUSE SYSGEN cannot determine if the tape was opened
correctly.
ACTION Change the file equation for the proper record size
and format.
-------------------------------------------------------------
0020 MESSAGE **error** SYSGEN won't write labelled tapes
CAUSE A file equation that created a labeled tape has
been entered. SYSGEN does not generate labeled
tapes.
ACTION Change the file equation for the proper format.
-------------------------------------------------------------
0022 MESSAGE **boot tape is successfully built**
CAUSE The boot tape is successfully generated.
ACTION None.
-------------------------------------------------------------
0023 MESSAGE **error** can't create store.pub.sys process
-------------------------------------------------------------
0024 MESSAGE **error** can't activate Store.pub.sys process
-------------------------------------------------------------
0025 MESSAGE **error** can't get reply from Store.pub.sys
process
-------------------------------------------------------------
0026 MESSAGE **error** error occurs while storing userfiles
-------------------------------------------------------------
0027 MESSAGE EOT is encountered. Please mount next reel to
continue tape operation. When tape is ready, enter
"yes" to continue.
-------------------------------------------------------------
0029 MESSAGE boottape generation. Otherwise, enter "no".
(yes/no)?
-------------------------------------------------------------
0040 MESSAGE **Boottape generation is aborted**
-------------------------------------------------------------
0041 MESSAGE **error** fail to mark end of tape
-------------------------------------------------------------
0051 MESSAGE pme = !
-------------------------------------------------------------
0052 MESSAGE label
-------------------------------------------------------------
0100 MESSAGE Please mount another tape for SYSGEN. This will
be reel # !
-------------------------------------------------------------
0101 MESSAGE Is SYSGEN's tape (reel !) ready (y/n)?
-------------------------------------------------------------
0105 MESSAGE Do you really want to abort the TAPE generation
(y/n)?
-------------------------------------------------------------
0200 MESSAGE ! non-user files will be written to tape
-------------------------------------------------------------
0201 MESSAGE dumping ! to tape
-------------------------------------------------------------
0500 MESSAGE **warning** No network configuration dumped!!
CAUSE A valid network configuration does not exist at the
time SYSGEN generates the boot tape.
ACTION Usually none. If you require a remote
configuration file, abort the tape and add a remote
configuration file to the local configuration
through the SYSFILE configurator RDCC command.
-------------------------------------------------------------
0501 MESSAGE **warning** ! will be ! on the tape.
CAUSE The file name is changed to a new file name on the
boot tape; for example, the remote configuration
file becomes NMCONFIG.PUB.SYS.
ACTION None.
-------------------------------------------------------------
0502 MESSAGE **warning** illegal file type. File ! dumped as
system file
CAUSE A file type created in the SYSFILE configurator is
corrupted. The file is dumped as a system program
type.
ACTION Either allow the system to use the default
configuration file(s) or reconfigure the file
through the SYSFILE configurator and generate a new
tape.
-------------------------------------------------------------
0503 MESSAGE **warning** File ! is empty.
-------------------------------------------------------------
1000 MESSAGE **error** couldn't find file !
-------------------------------------------------------------
1001 MESSAGE **error** Error in counting number of diag files
-------------------------------------------------------------
1002 MESSAGE **error** ! is not a bootable image
CAUSE Through the SYSFILE configurator, you have declared
a file to be a bootable image. It is not.
ACTION After tape generation, check your file for errors.
Correct it and add it to the system through the
SYSFILE SBOOT command.
-------------------------------------------------------------
1003 MESSAGE **error** Can't read file label of file !
CAUSE This is caused by an I/O error.
-------------------------------------------------------------
1004 MESSAGE **error** No disc ipl boot file--Can't make tape.
CAUSE Through deletion or modification, no boot image is
designated as the ISC IPL file. The system
requires that both a disk and a tape IPL file be
present.
ACTION As the original file should still exist in the
proper account, add the image and file name to
SYSFILEP through the SYSFILE configurator command
ABOOT. Retry the TAPE command.
-------------------------------------------------------------
1005 MESSAGE **error** No tape ipl boot file--Can't make tape.
CAUSE Through deletion or modification, no boot image is
designated as the tape IPL file. The system
requires that both a disk and a tape IPL file be
present.
ACTION As the original file should still exist in the
proper account, add the image and file name to
SYSFILEP through the SYSFILE configurator command
ABOOT. Retry the TAPE command.
-------------------------------------------------------------
1006 MESSAGE **error** records of file ! too long for SYSGEN
CAUSE The tape block size is greater than the size
required by SYSGEN (currently 16 K).
ACTION Decrease the block size in the file.
-------------------------------------------------------------
1007 MESSAGE **error** The tape boot files must fit on 1 tape.
CAUSE All files of type (tapeboot, tapeauto, tapeipl) as
well as type both (bothboot, botauto, bothipl) must
fit on one reel.
ACTION Use a tape of sufficient size, and delete
unnecessary or outdated boot files through the
SYSFILE configurator DBOOT command.
-------------------------------------------------------------
1008 MESSAGE Ran out of tape while dumping file: !
CAUSE Same as above.
-------------------------------------------------------------
1009 MESSAGE **error** Couldn't write eof mark on tape
CAUSE A hardware failure occurs on the drive.
ACTION Check that the tape is good and that it has been
mounted properly. Replace the tape if necessary
and try again. If failure occurs, the problem is
more than likely with the tape drive. Try another
drive. Contact your CE.
-------------------------------------------------------------
1010 MESSAGE **error** Can't rewind tape
CAUSE A hardware failure occurs on the drive.
ACTION Check that you tape is still mounted properly.
check that the drive is still functioning. If the
problem is not immediately discernible, use another
drive for generating your tapes.
-------------------------------------------------------------
1011 MESSAGE **error** File ! is empty.
-------------------------------------------------------------
1015 MESSAGE **error** Can't close file !.
-------------------------------------------------------------
1016 MESSAGE **error** bad diagnostic file name (!) in !
-------------------------------------------------------------
1020 MESSAGE **error** Can't create temporary LID file
-------------------------------------------------------------
1021 MESSAGE **error** Can't close temporary LID file
-------------------------------------------------------------
1022 MESSAGE **error** Can't create temporary DST file
-------------------------------------------------------------
1023 MESSAGE **error** Can't close temporary DST file
-------------------------------------------------------------
1024 MESSAGE **error** Can't write to temporary file for !
-------------------------------------------------------------
1030 MESSAGE **error** Tape command failed SYSGEN tape is NO
GOOD
CAUSE There is a problem with the tape used, a base
system file is corrupted, or the configuration file
SYSFILEP contains a file name that is no longer
valid.
ACTION First, check any associated message that appears,
particularly messages that indicate a file cannot
be found or is corrupted. SYSDILEP contains a
listing of files SYSGEN expects to put out to a
boot tape. Check to be sure the base file is still
a valid file for your current software release. If
it is not, delete the file from SYSFILEP using the
DSPROG command in the SYSFILE configurator. If a
file is corrupted, restore it from your system
backup tape. If there are no accompanying
messages, mount a different tape. Check the tape
drive.
-------------------------------------------------------------