HP 3000 Manuals

Class Errors (Cont'd.) [ MPE/iX Error Messages Manual Volume II ] MPE/iX 5.5 Documentation


MPE/iX Error Messages Manual Volume II

Class Errors (Cont'd.) 

Class Error 3:  System Monitor Card Failure 

System monitor card messages take the form:

       30xx

where:

       xx = detailed error number.

-------------------------------------------------------------

 00          MESSAGE    No message. System halts. (E)

           CAUSE      Undefined error occurs at the start of the test of
                      this board.

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 01          MESSAGE    No message. System halts. (E)

           CAUSE      data error occurs while verifying byte 10c (hex) of
                      nonvolatile memory (NVM).

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 02          MESSAGE    No message. System halts. (E)

           CAUSE      General register 0 is not zero at transfer of
                      control (TOC).

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 03          MESSAGE    No message. System halts. (E)

           CAUSE      Invalid return address received for TOC. Second
                      possible cause of the error is memory.

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 07          MESSAGE    No message. System halts. (E)

           CAUSE      Cannot verify processor dependent code (PDC) PROM.
                      No PDC PROM installed.

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 08          MESSAGE    No message. System halts. (E)

           CAUSE      Cannot find second part of self-test in PDC PROM.
                      PDC PROM not installed.

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 09          MESSAGE    No message. System halts. (E)

           CAUSE      Cannot find PDC code in PDC PROM.

           ACTION     check PDC PROM. Contact your Hewlett-Packard
                      Support Representative.

-------------------------------------------------------------

 0A          MESSAGE    No message. System halts. (E)

           CAUSE      Cannot initialize memory with switch 3 open.

           ACTION     Try booting with switch 3 in normal position.
                      Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 0B          MESSAGE    No message. System halts. (E)

           CAUSE      General register 0 is not found to be zero at TOC
                      or HPMC save state routine.

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 0C          MESSAGE    No message. System halts. (E)

           CAUSE      Undefined error message occurs for HPMC in HPMC
                      save state routine.

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 0D          MESSAGE    No message. System halts. (E)

           CAUSE      Cannot verify checksum while downloading code from
                      EPROM on system monitor card.

           ACTION     Contact your Hewlett-Packard Support
                      Representative.

-------------------------------------------------------------

 0E          MESSAGE    No message. System boots. (W)

           CAUSE      Self-test completes with warning.

           ACTION     check warning message(s).  Contact your HP
                      Representative if future problem occurs.

-------------------------------------------------------------

 0F          MESSAGE    No message. System boots. (I)

           CAUSE      Self-test completes successfully.

-------------------------------------------------------------

 21          MESSAGE    No message. Self-test continues. (W)

           CAUSE      Verification of stable storage fails.

           ACTION     Contact your HP Representative if system halt
                      occurs or future problem encountered.

-------------------------------------------------------------

 22          MESSAGE    No message. Self-test continues. (W)

           CAUSE      Failure occurs while reading from stable storage.

           ACTION     Contact your HP Support Representative if system
                      halt occurs or future problem encountered.

-------------------------------------------------------------

 28          MESSAGE    No message. Self-test continues. (W)

           CAUSE      Failure occurs while reading from time-of-day
                      clock.

           ACTION     Contact your HP Support Representative if system
                      halt occurs or future problem encountered.  check
                      time-of-day entry during START routine.

-------------------------------------------------------------



MPE/iX 5.5 Documentation