HP 3000 Manuals HP 3000 Manuals
Chapter 19 KSAM (Subsystem 143) ------------------------------------------------------------
NOTE KSAM error messages are included with subsystem 143 (File System) messages. Refer to chapter 4, File System (Native Mode), for listing of messages.
------------------------------------------------------------ ------------------------------------------------------------- 1026 MESSAGE Type manager; an internal error occurred. CAUSE You requested a lower level system service and this reported an error to the type manager. ACTION If the problem persists, contact your Hewlett-Packard support engineer. ------------------------------------------------------------- 1079 MESSAGE TM_KSM_INVALID_OFFSET CAUSE The file offset pointer calculated for the KSAM file is invalid. ACTION Close the KSAM file, store it to tape, and call your Hewlett-Packard support representative. ------------------------------------------------------------- 1080 MESSAGE TM_KSM_UNEXPECTED_ERROR CAUSE During an operation on a KSAM file, a non-file system error occurred. ACTION Close the KSAM file, store it to tape, and call your Hewlett-Packard support representative. ------------------------------------------------------------- 6005 MESSAGE Type manager; invalid function code or parameter. CAUSE An FCONTROL or FDEVICECONTROL function, or one of its parameters, is not valid for the particular device or access method in which it was used. It may also be invalid for any device (for example, out of range). ACTION Check the intrinsic call for which the error is reported and correct any errors in the calling sequence. ------------------------------------------------------------- 6006 MESSAGE Type manager; you specified a parameter value that is more than the maximum specified for this function. CAUSE Self-explanatory. ACTION Use the MPE XL Intrinsics manual to verify the set of acceptable parameters for a given function code. ------------------------------------------------------------- 6007 MESSAGE Type manager; you specified a parameter value that is less than the minimum specified for this function. CAUSE Self-explanatory. ACTION Use the MPE XL Intrinsics manual to verify the set of acceptable parameters for a given function code. ------------------------------------------------------------- 6013 MESSAGE Type manager; device is off-line. CAUSE For printers attached via the Distributed Terminal Controller (DTC), this is a generic error indicating the inability of the DTC to communicate with its device. It is currently not returned for other devices. ACTION Check the DTC-to-device cable connections, parity and baud rate settings, DTR and CTS settings, and Transmit/Receive Pacing settings. Ensure that they are set as required for proper use by the DTC. ------------------------------------------------------------- 6022 MESSAGE Type manager; unit failure. CAUSE An undetermined device or transmission error occurred. ACTION Check lower level statuses to determine the root cause of the error. ------------------------------------------------------------- 6025 MESSAGE Type manager; timeout while waiting for I/O completion. CAUSE This usually indicates a hardware failure of some component of the I/O subsystem. ACTION Contact your Hewlett-Packard support engineer. ------------------------------------------------------------- 6026 MESSAGE Type manager; data transmission error. CAUSE An undetermined transmission error was reported by a lower level subsystem. ACTION Check the lower level statuses to determine the root cause of the error. ------------------------------------------------------------- 6029 MESSAGE Type manager; the device reported a power-up. CAUSE Self-explanatory. For printers, this status is returned only if device status reporting is disable (the default). If it is enabled, the intrinsic interface returns CCG instead, indicating that status is available. ACTION The application or operator should take whatever steps are appropriate (for example, putting the device on line). For printers, the Native Mode Spooler will attempt to recover to the start of the current page. ------------------------------------------------------------- 6035 MESSAGE Type manager; your I/O request was aborted due to a system power failure. CAUSE Self-explanatory. ACTION If the device is owned by a spooler, the spooler process will terminate. Restart the process. For other situations, take whatever steps are appropriate to re-establish normal device operation. ------------------------------------------------------------- 6036 MESSAGE Type manager; data lost. CAUSE A lower level subsystem has reported an error of some kind which resulted in an incomplete data transfer. ACTION Check the lower level statuses to determine the root cause of the error. ------------------------------------------------------------- 6037 MESSAGE Type manager; the I/O request was aborted externally. CAUSE Either you entered an explicit ABORTIO, or the process with outstanding I/O is being terminated. ACTION None. ------------------------------------------------------------- 6039 MESSAGE Type manager; the device reported a parity error. CAUSE Self-explanatory. ACTION Take whatever steps are appropriate, for example, cleaning tape heads. If the problem persists, contact your Hewlett-Packard support engineer. -------------------------------------------------------------