HP 3000 Manuals HP 3000 Manuals
(Subsystem 236)(Continued)
------------------------------------------------------------
5355 MESSAGE Could not change the STDLIST device in
JOB/SESSION tables.
-------------------------------------------------------------
5356 MESSAGE File does not exist or could not be created.
-------------------------------------------------------------
5357 MESSAGE SPOOLF ;PRINT -- valid range of copies is 1 to
65535.
-------------------------------------------------------------
5358 MESSAGE SPOOLF ;PRINT -- valid range of priorities is 0
to 14.
-------------------------------------------------------------
5359 MESSAGE Cannot open the file for exclusive access because
it is already open.
-------------------------------------------------------------
5360 MESSAGE The specified lockword does not match the
lockword on the file.
-------------------------------------------------------------
5361 MESSAGE You cannot UNDEFER a spoolfile in the PROBLM
state.
-------------------------------------------------------------
5362 MESSAGE You cannot UNDEFER a spoolfile in the SPSAVE
state.
-------------------------------------------------------------
5367 MESSAGE You cannot alter the attributes of an input
spoolfile.
-------------------------------------------------------------
5368 MESSAGE You cannot delete an ACTIVE ":DATA" input
spoolfile, that is, one currently being submitted
via the STREAM command.
-------------------------------------------------------------
5369 MESSAGE You cannot delete an output spoolfile which is in
the CREATE state.
-------------------------------------------------------------
5370 MESSAGE You cannot delete an input spoolfile which is in
the OPEN state.
-------------------------------------------------------------
5373 MESSAGE Only output spoolfiles can be SPOOLF ;PRINT'ed.
-------------------------------------------------------------
5374 MESSAGE You cannot SPOOLF :PRINT an input spoolfile.
-------------------------------------------------------------
5375 MESSAGE The source file for a SPOOLF :PRINT has no target
device or class to use as a default, therefore you
must specify one with the command.
-------------------------------------------------------------
5376 MESSAGE The defaulted target device (taken from the
source spoolfile of a SPOOLF :PRINT command) is not
a valid output spooled device.
-------------------------------------------------------------
5377 MESSAGE Could not open the source file for a SPOOLF
:PRINT command.
-------------------------------------------------------------
5378 MESSAGE Could not open the target file for a SPOOLF
:PRINT command.
-------------------------------------------------------------
5379 MESSAGE The first character of a file lockword must be a
letter.
-------------------------------------------------------------
5380 MESSAGE Too many characters were specified for the file
lockword.
-------------------------------------------------------------
5381 MESSAGE The file lockword contains a non-alphanumeric
character.
-------------------------------------------------------------
5382 MESSAGE Altering the target device of a Private spoolfile
requires SM capability.
-------------------------------------------------------------
5383 MESSAGE Could not change the target device of an open
STDLIST.
-------------------------------------------------------------
5384 MESSAGE Error encountered checking the target device
-------------------------------------------------------------
5385 MESSAGE Creator of spoolfile does not have access to the
target device.
-------------------------------------------------------------
5386 MESSAGE If there is not an ACD on the target device, the
accessor must have ND (non-sharable device)
capability.
-------------------------------------------------------------
5387 MESSAGE An internal call to JSINFO failed.
-------------------------------------------------------------
5388 MESSAGE The creator of the spoolfile does not have access
to the target device on a SPOOLF;DEV= or
SPOOLF;UNDEFER. This error is used when a "Spoolid"
insert is desired at the SP_AI level.
-------------------------------------------------------------
5389 MESSAGE The user does not have access to the device
specified in the label extension of the spoolfile.
This error is used when a "file name" insert is
desired at the SP_AI level.
-------------------------------------------------------------
5390 MESSAGE The device specified in the label extension of
the spoolfile does not have an ACD and the user
does not have ND capability. This error is used
when a "file name" insert is desired at the SP_AI
level.
-------------------------------------------------------------
7500 MESSAGE An invalid DEV keyvalue was specified in the
selection equation.
-------------------------------------------------------------
7501 MESSAGE Only = and <> are allowed as relational operators
for the DEV selection equation keyword.
-------------------------------------------------------------
7502 MESSAGE An invalid PAGES keyvalue was specified in the
selection equation.
-------------------------------------------------------------
7503 MESSAGE The COPIES keyvalue must be in the range of 1 to
65,535.
-------------------------------------------------------------
7504 MESSAGE The PRI keyvalue must be in the range of 0 to 14.
-------------------------------------------------------------
7505 MESSAGE An invalid FILEDES keyvalue was specified in the
selection equation.
-------------------------------------------------------------
7506 MESSAGE Only '=' and <> are allowed as relational
operators for the FILEDES selection equation
keyword.
-------------------------------------------------------------
7507 MESSAGE Only = and <> are allowed as relational operators
for the JOBNUM selectioni equation keyword.
-------------------------------------------------------------
7508 MESSAGE An invalid DATE keyvalue was specified in the
selection equation.
-------------------------------------------------------------
7509 MESSAGE In the DATE keyvalue of the selection equation,
the month must be in the range of 1 to 12.
-------------------------------------------------------------
7510 MESSAGE An invalid year was specified in the DATE
keyvalue of the selection equation.
-------------------------------------------------------------
7511 MESSAGE An invalid JOBNUM keyvalue was specified in the
selection equation.
-------------------------------------------------------------
7512 MESSAGE An invalid JOBNAME keyvalue was specified in the
selection equation.
-------------------------------------------------------------
7513 MESSAGE An invalid FORMID keyvalue was specified in the
selection equation.
-------------------------------------------------------------
7514 MESSAGE You must specify an account to use this command.
-------------------------------------------------------------
7515 MESSAGE A valid user name consists of a letter followed
by alphanumeric characters.
-------------------------------------------------------------
7516 MESSAGE A valid account name consists of a letter
followed by alphanumeric characters.
-------------------------------------------------------------
7517 MESSAGE The user name must contain eight or less
characters.
-------------------------------------------------------------
7518 MESSAGE The account name must contain eight or less
characters.
-------------------------------------------------------------
7519 MESSAGE The RECORDS keyvalue must be a positive integer.
-------------------------------------------------------------
7520 MESSAGE Only = and <> are allowed as relational operators
for the OWNER selection equation keyword.
-------------------------------------------------------------
7521 MESSAGE Internal error while evaluating selection
equation, there was no result to return. If this
error persists, contact your SE.
-------------------------------------------------------------
7522 MESSAGE The DEV keyvalue must contain eight or less
characters.
-------------------------------------------------------------
7524 MESSAGE Valid STATE keyvalues are READY, ACTIVE, OPEN,
CREATE, PRINT, PROBLM, DELPND, SPSAVE, DEFER.
-------------------------------------------------------------
7525 MESSAGE Only = and <> are allowed as relational operators
for the STATE selection equation keyword.
-------------------------------------------------------------
7526 MESSAGE The SPOOLID keyvalue must contain seven or fewer
digits, not including the optional #0 or #1.
-------------------------------------------------------------
7527 MESSAGE The FILEDES keyvalue is too long.
-------------------------------------------------------------
7528 MESSAGE The JOBNUM keyvalue must be in the range of 1 to
16383.
-------------------------------------------------------------
7529 MESSAGE The JOBNAME keyvalue must contain eight or less
characters.
-------------------------------------------------------------