HP 3000 Manuals HP 3000 Manuals
MPE/iX Commands Reference Manual Volume I 900 Series HP 3000 Computer Systems HP Part No. 32650-90003 Printed in U.S.A. Edition Eigth Edition E0195
________________________________________________________________________ |The information contained in this document is subject to change | |without notice. | | | |Hewlett-Packard makes no warranty of any kind with regard to this | |material, including, but not limited to, the implied warranties of | |merchantability or fitness for a particular purpose. Hewlett-Packard | |shall not be liable for errors contained herein or for direct, | |indirect, special, incidental or consequential damages in connection | |with the furnishing or use of this material. | | | |Hewlett-Packard assumes no responsibility for the use or reliability | |of its software on equipment that is not furnished by Hewlett-Packard.| | | |This document contains proprietary information which is protected by | |copyright. All rights are reserved. Reproduction, adaptation, or | |translation without prior written permission is prohibited, except as | |allowed under the copyright laws. | ________________________________________________________________________ Copyright (c) 1995 by Hewlett-Packard Company ________________________________________________________________________ |Use, duplication, or disclosure by the U.S. Government is subject to | |restrictions as set forth in subparagraph (c) (1) (ii) of the Rights | |in Technical Data and Computer Software clause at DFARS 252.227-7013 | |for DoD agencies, Computer Software Restricted Rights clause at FAR | |52.227-19 for other agencies. | | | |Hewlett-Packard Company | |3000 Hanover Street | |Palo Alto, CA 94304 U.S.A. | ________________________________________________________________________ Restricted Rights Legend Printed 1995 Printing History The following table lists the printings of this document, together with the respective release dates for each edition. The software version indicates the version of the software product at the time this document was issued. Many product releases do not require changes to the document. Therefore, do not expect a one-to-one correspondence between product releases and document editions. Edition Date Software Version --------------------------------------------------------------------------------------- First Edition November 1987 A.01.00 Update 1 July 1988 A.10.00 Second Edition October 1989 A.30.00 Third Edition April 1990 A.40.00 Fourth Edition December 1990 B.30.00 Fifth Edition June 1992 B.40.00 Sixth Edition February 1994 C.47.00 Seventh Edition April 1994 C.50.00 Eighth Edition January 1995 C.50.00 Preface The eighth edition of the MPE/iX Commands Reference Manual (32650-90003) is a two volume set. Volume 1 provides command descriptions alphabetically from A through L. Volume 2 provides command descriptions alphabetically from M-X. This two-volume manual is written for all users of the 900 Series HP 3000. MPE/iX, Multiprogramming Executive with Integrated POSIX, is the latest in a series of forward-compatible operating systems for the HP 3000 line of computers. In HP documentation and in talking with HP 3000 users, you will encounter references to MPE XL, the direct predecessor of MPE/iX. MPE/iX is a superset of MPE XL. All programs written for MPE XL will run without change unde MPE/iX. You can continue to use MPE XL system documentation, although it may not refer to features added to the operating system to support POSIX (for example, hierarchical directories). Finally, you may encounter references to MPE V, which is the operating system for HP 3000s, not based on the PA-RISC architecture. MPE V software can be run on the PA-RISC (Series 900) HP 3000s in what is known as compatibility mode. Organization of This Manual The MPE/iX Commands Reference Manual (32650-90003) is organized into two chapters. A description of each chapter follows: Chapter 1 Commands by Task provides an introduction to all MPE/iX commands and their functions, categorized by the task they perform. Chapter 2 Command Definitions provides documentation on each MPE/iX command alphabetically for your ease of use. Commands beginning with the letters A through L can be found in volume 1. Commands beginning with the letters M through Z can be found in volume 2. How to Use This Manual Chapter 2 of this manual, which is spread over two volumes, explains the purpose, syntax, parameters, and operation (including examples) for each MPE/iX command. If you know which command to use for the task you wish to perform, turn directly to that command definition in chapter 2. For your convenience, commands are organized alphabetically. If you don't know which command to use, chapter 1, which contains a listing of commands by task, is a good place to start. After reading the brief description, turn to the appropriate volume and command definition in chapter 2. For supplemental information on command syntax and use, refer to the MPE/iX General User's Reference Manual (32650-90002). Conventions UPPERCASE In a syntax statement, commands and keywords are shown in uppercase characters. The characters must be entered in the order shown; however, you can enter the characters in either uppercase or lowercase. For example: COMMAND can be entered as any of the following: command Command COMMAND It cannot, however, be entered as: comm com_mand comamnd italics In a syntax statement or an example, a word in italics represents a parameter or argument that you must replace with the actual value. In the following example, you must replace filename with the name of the file: COMMAND filename bold italics In a syntax statement, a word in bold italics represents a parameter that you must replace with the actual value. In the following example, you must replace filename with the name of the file: COMMAND(filename) punctuation In a syntax statement, punctuation characters (other than brackets, braces, vertical bars, and ellipses) must be entered exactly as shown. In the following example, the parentheses and colon must be entered: (filename):(filename) underlining Within an example that contains interactive dialog, user input and user responses to prompts are indicated by underlining. In the following example, yes is the user's response to the prompt: Do you want to continue? >> yes { } In a syntax statement, braces enclose required elements. When several elements are stacked within braces, you must select one. In the following example, you must select either ON or OFF: COMMAND { ON } { OFF} [ ] In a syntax statement, brackets enclose optional elements. In the following example, OPTION can be omitted: COMMAND filename [OPTION] When several elements are stacked within brackets, you can select one or none of the elements. In the following example, you can select OPTION or parameter or neither. The elements cannot be repeated. COMMAND filename [ OPTION ] [ parameter] Conventions (continued) [...] In a syntax statement, horizontal ellipses enclosed in brackets indicate that you can repeatedly select the element(s) that appear within the immediately preceding pair of brackets or braces. In the example below, you can select parameter zero or more times. Each instance of parameter must be preceded by a comma: [,parameter][...] In the example below, you only use the comma as a delimiter if parameter is repeated; no comma is used before the first occurrence of parameter: [parameter][,...] |...| In a syntax statement, horizontal ellipses enclosed in vertical bars indicate that you can select more than one element within the immediately preceding pair of brackets or braces. However, each particular element can only be selected once. In the following example, you must select A, AB, BA, or B. The elements cannot be repeated. { A} |...| { B} ... In an example, horizontal or vertical ellipses indicate where portions of an example have been omitted. In a syntax statement, the space symbol shows a required blank. In the following example, parameter and parameter must be separated with a blank: (parameter) (parameter) The symbol indicates a key on the keyboard. For example, RETURN represents the carriage return key or Shift represents the shift key. CTRLcharacter CTRLcharacter indicates a control character. For example, CTRLY means that you press the control key and the Y key simultaneously.