HP 3000 Manuals HP 3000 Manuals
Using >SHOW to Display the Translation Table
Use the >SHOW command to display the translation table on your terminal
screen or have it printed on the system printer.
To display the standard ASCII translation table on the terminal screen,
use the TABLE parameter of the >SHOW command. The translation table
follows the standard 128-character ASCII sequence. It shows the ordinal
value for each character. For example, the numeric value for F is 70
(decimal). To generate the ASCII translation table, enter the following
commands:
:SORT
HP32214A.01.00 SORT/3000 WED, JUN 3, 1987, 9:20 AM
(c) HEWLETT-PACKARD CO. 1986
>DATA IS ASCII, SEQUENCE IS ASCII
>SHOW TABLE
TABLE OF ORDINAL VALUE ASSIGNED TO EACH CHARACTER.
! 0 ! 1 ! 2 ! 3 ! 4 ! 5 ! 6 ! 7 ! 8 ! 9
----+------+------+------+------+------+------+------+------+------+------
0 ! 0 ! 1 ! 2 ! 3 ! 4 ! 5 ! 6 ! 7 ! 8 ! 9 !
1 ! 10 ! 11 ! 12 ! 13 ! 14 ! 15 ! 16 ! 17 ! 18 ! 19 !
2 ! 20 ! 21 ! 22 ! 23 ! 24 ! 25 ! 26 ! 27 ! 28 ! 29 !
3 ! 30 ! 31 !sp=32 !!= 33 !"= 34 !#= 35 !$= 36 !%= 36 !&= 38 !'= 39 !
4 !(= 40 !)= 41 !*= 42 !+= 43 !,= 44 !-= 45 !.= 46 !/= 47 !0= 48 !1= 49 !
5 !2= 50 !3= 51 !4= 52 !5= 53 !6= 54 !7= 55 !8= 56 !9= 57 !:= 58 !;= 59 !
6 !<= 60 !== 61 !>= 62 !?= 63 !@= 64 !A= 65 !B= 66 !C= 67 !D= 68 !E= 69 !
7 !F= 70 !G= 71 !H= 72 !I= 73 !J= 74 !K= 75 !L= 76 !M= 77 !N= 78 !O= 79 !
8 !P= 80 !Q= 81 !R= 82 !S= 83 !T= 84 !U= 85 !V= 86 !W= 87 !X= 88 !Y= 89 !
9 !Z= 90 ![= 91 !\= 92 !]= 93 !^= 94 !_= 95 !`= 96 !a= 97 !b= 98 !c= 99 !
10 !d=100 !e=101 !f=102 !g=103 !h=104 !i=105 !j=106 !k=107 !l=108 !m=109 !
11 !n=110 !o=111 !p=112 !q=113 !r=114 !s=115 !t=116 !u=117 !v=118 !w=119 !
12 !x=120 !y=121 !z=122 !{=123 !|=124 !}=125 !~=126 ! =127 ! 128 ! 129 !
13 ! 130 ! 131 ! 132 ! 133 ! 134 ! 135 ! 136 ! 137 ! 138 ! 139 !
14 ! 140 ! 141 ! 142 ! 143 ! 144 ! 145 ! 146 ! 147 ! 148 ! 149 !
15 ! 150 ! 151 ! 152 ! 153 ! 154 ! 155 ! 156 ! 157 ! 158 ! 159 !
16 ! 160 ! 161 ! 162 ! 163 ! 164 ! 165 ! 166 ! 167 ! 168 ! 169 !
17 ! 170 ! 171 ! 172 ! 173 ! 174 ! 175 ! 176 ! 177 ! 178 ! 179 !
18 ! 180 ! 181 ! 182 ! 183 ! 184 ! 185 ! 186 ! 187 ! 188 ! 189 !
19 ! 190 ! 191 ! 192 ! 193 ! 194 ! 195 ! 196 ! 197 ! 198 ! 199 !
20 ! 200 ! 201 ! 202 ! 203 ! 204 ! 205 ! 206 ! 207 ! 208 ! 209 !
21 ! 210 ! 211 ! 212 ! 213 ! 214 ! 215 ! 216 ! 217 ! 218 ! 219 !
22 ! 220 ! 221 ! 222 ! 223 ! 224 ! 225 ! 226 ! 227 ! 228 ! 229 !
23 ! 230 ! 231 ! 232 ! 233 ! 234 ! 235 ! 236 ! 237 ! 238 ! 239 !
24 ! 240 ! 241 ! 242 ! 243 ! 244 ! 245 ! 246 ! 247 ! 248 ! 249 !
25 ! 250 ! 251 ! 252 ! 253 ! 254 ! 255 !
WHEN PASSED TO SORTINIT, THE TABLE ABOVE IS PRECEDED BY TWO BYTES. THESE
FIRST TWO BYTES CONTAIN A FLAG BYTE OF %000 AND A LENGTH BYTE OF %377
RESPECTIVELY.
This translation table display is followed by a display of the contents
of the ALTSEQ array in decimal format and octal word format. This
information is not shown here as it is intended for programmatic use.
Refer to the SORT-MERGE/XL Programmer's Guide (32650-90080) for
additional information.
To receive a copy of the standard ASCII translation table from the
printer, use the OFFLINE parameter of the >SHOW command, as follows:
>DATA IS ASCII, SEQUENCE IS ASCII
>SHOW TABLE, OFFLINE
For additional information on translation tables refer to the >SHOW
command in Chapter 6.