HP 3000 Manuals HP 3000 Manuals
To Add User Capabilities
The ADDCAP command file adds capabilities to a user's capability list.
The ALTUSER command is used to alter the capability list. The AM
capability, therefore, is required to execute this command file.
Since the new capability does not become effective until the user
logs on again, the user is offered the option of being logged on
automatically.[REV BEG] This command also permits an authorized user to
change the UID of a user. Refer to New Features of MPE/iX: Using The
Hierarchical File System (32650-90351).[REV END]
______________________________________________________________________________
| |
| PARM CAP="" |
| IF ("!CAP"="") THEN |
| ECHO (ADDCAP): Your capabilities are: !HPUSERCAPF. |
| RETURN |
| ENDIF |
| IF (POS(UPS("!CAP"),HPUSERCAPF) <> 0) THEN |
| ECHO (ADDCAP): You already have : !CAP. |
| ECHO (ADDCAP): The capabilities are: !HPUSERCAPF. |
| RETURN |
| ENDIF |
| SETVAR CIERROR 0 |
| CONTINUE |
| ALTUSER !HPUSER;CAP=![HPUSERCAPF + ",!CAP"] |
| IF CIERROR <> 0 THEN |
| ECHO (ADDCAP): The capabilities remain: !HPUSERCAPF. |
| ELSE |
| ECHO (ADDCAP): !HPUSER new capabilities are: ![HPUSERCAPF + ",!CAP"].|
| SETVAR ADDCAP_TEMP "N" |
| INPUT ADDCAP_TEMP,"(ADDCAP): Log off/on now (Y/N) ==>",10 |
| IF HPCIERR = -9003 THEN |
| COMMENT ** TIMED READ EXPIRED ** |
| ECHO |
| ECHO (ADDCAP): Timed 10-second read expired. & |
| Logon cancelled. |
| ELSEIF NOT(UPS(LFT(ADDCAP_TEMP,1)) = "Y") THEN |
| ECHO (ADDCAP): New capabilities take effect at next & |
| logon. |
| ELSE |
| HELLO !HPJOBNAME,!HPUSER.!HPACCOUNT,!HPGROUP |
| ENDIF |
| ENDIF |
| DELETEVAR ADDCAP_TEMP |
| COMMENT ** END OF ADDCAP ** |
______________________________________________________________________________
Figure 7-5. Additional Capability Command File
An error routine is triggered by the contents of CIERROR. If an
unacceptable parameter is entered, the CIERROR field is updated and the
capabilities remain as they were.
There are three possible outcomes in running this command file using
acceptable input:
* No capability was entered as a parameter value. The user's
current capabilities are listed.
* The user already has the capability.
* The capability is added to the user's list. Note that a relogging
option prompts the user to relog automatically or to wait until
the next logon to activate the new capabilities.
The following examples illustrate these three possibilities.
__________________________________________________________________
| |
| |
| :ADDCAP |
| (ADDCAP): Your capabilities are: AM,BA,IA |
| |
| |
| :ADDCAP AM |
| (ADDCAP): You already have : AM |
| (ADDCAP): The capabilities are: AM,BA,IA |
| |
| |
| :ADDCAP DS |
| (ADDCAP): SAMPLE new capabilities are: AM,BA,IA,DS |
| (ADDCAP): Log off/on now Y/N ==> |
| |
| (ADDCAP): Timed 10-second read expired. Logon cancelled. |
| |
__________________________________________________________________
Figure 7-6. ADDCAP Sample Output