HP 3000 Manuals HP 3000 Manuals
Chapter 79 TermDSM
(TDSM)
--------------------------------------------------------------
---------------------------------------------------------------
15 MESSAGE You have entered an unknown or incorrect command.
Please try again. (TDSM 15)
CAUSE You have entered something that is not a TermDSM
command or a command that is not valid in this
context.
ACTION Commands that are valid at this time are listed in
the prompt. Please try again. Type HELP or refer
to the reference documentation for more
information.
---------------------------------------------------------------
16 MESSAGE TermDSM has compiled without $partial eval$ in
effect. It cannot continue. This problem must be
fixed at the factory. (TDSM 16)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
17 MESSAGE Your security level (3) is too low to use
TermDSM. Please log on with level 0, 1, or 2
security. (TDSM 17)
CAUSE You do not have the correct user capabilities to
use TermDSM. For level 0, you need SM capability.
For level 1, you need SM or DI capability. For
level 2, you need SM or DI or OP capability.
ACTION Logon as a user with the correct capabilities for
the TermDSM functions you wish to use. Refer to
reference documentation for the security levels of
each command and subcommand.
---------------------------------------------------------------
18 MESSAGE You have entered a bad port number. Port numbers
range from 0 to 7. (TDSM 18)
CAUSE The value you entered is not a number between zero
and seven.
ACTION Enter a valid port number. Check the port number
on the back of the DTC if necessary.
---------------------------------------------------------------
19 MESSAGE The port number is missing or invalid. Port
numbers range from 0 to 7. (TDSM 19)
CAUSE The port number was not entered or is
unrecognizable.
ACTION Enter a valid port number. Refer to the reference
documentation for syntax.
---------------------------------------------------------------
20 MESSAGE You have entered an incorrect ldev number. Ldev
numbers are positive integers. (TDSM 20)
CAUSE The value that you entered as a logical device
number is not a number greater than zero.
ACTION Enter a valid ldev number. Note that you can also
use the port subcommand.
---------------------------------------------------------------
21 MESSAGE The ldev number is missing or invalid. Ldev
numbers are positive integers. (TDSM 21)
CAUSE The logical device number was not entered or is
unrecognizable.
ACTION Enter a valid ldev number. Note that you can also
use the port subcommand.
---------------------------------------------------------------
22 MESSAGE You have entered an invalid SIC card number. SIC
card numbers range from 0 to 5. (TDSM 22)
CAUSE The card number that you entered in is not the
range zero to five.
ACTION Doublecheck the card numbers by looking at the back
of the DTC. Enter the card number again.
---------------------------------------------------------------
23 MESSAGE The SIC card number is missing or invalid. SIC
card numbers range from 0 to 5. (TDSM 23)
CAUSE The card number was not entered or is
unrecognizable.
ACTION Enter the card number again. Refer to the prompt
or to the reference documentation for syntax.
---------------------------------------------------------------
24 MESSAGE You have entered an incorrect DTC number. Please
choose a DTC number from this list. (TDSM 24)
CAUSE The value entered does not correspond with any DTC
on the system.
ACTION The DTCs on the system are listed with their
numbers. Enter one of the numbers displayed.
---------------------------------------------------------------
25 MESSAGE The DTC number is missing or invalid. Please
choose a DTC number from this list. (TDSM 25)
CAUSE The DTC number was not entered or is
unrecognizable.
ACTION The DTCs on the system are listed with their
numbers. Enter one of the numbers displayed.
---------------------------------------------------------------
27 MESSAGE TermDSM cannot do the dump because there are
already too many dump files. Please purge some.
Dump files are of the form TRMnnnaa.PUB.SYS. where
nn is a 3 digit number and aa is 2 alphabetic
characters. (TDSM 27)
CAUSE The dump files TRMdddAA through TRMdddZZ already
exist. (The sequence ddd is the current Julian
date.)
ACTION Delete some files beginning with the file called
TRMdddAA since this is the oldest file. Note that
if all files for this Julian date already exist,
there are over 600 dump files for today. You can
delete most of these files.
---------------------------------------------------------------
32 MESSAGE Your security level (3) is too low to take dumps.
Please log on with level 2 security to dump ports,
or level 0 security to dump ports and DTCs. (TDSM
32)
For level 1, you need SM or DI capability. For
level 2, you need SM or DI or OP capability.
CAUSE You do not have the correct user capabilities to
use this function.
ACTION Log on with level 0, 1, or 2 security. Refer to
the reference documentation for the security levels
of each command and subcommand.
---------------------------------------------------------------
34 MESSAGE That ldev does not exist. Please check the ldev
number, or dump the associated port instead. (TDSM
34)
CAUSE Although you entered a number in a range that could
be an ldev number, that ldev number is not
configured on the system.
ACTION Verify the ldev number by entering the SHOWJOB
command. You can also dump information associated
with the device by using the PORT subcommand (which
uses the physical address instead of the ldev
number).
---------------------------------------------------------------
35 MESSAGE That DTC is owned by another person running
TermDSM. You may override that user and continue.
(WARNING : This may have unpredictable results.
It's safer to find the other user and exit TermDSM.
(TDSM 35) Do you want to override the other user
(yes or no)?
CAUSE More than one person is using TermDSM and directing
operations to the same DTC at the same time.
ACTION It is permissible for two or more users to run
TermDSM simultaneously as long as the users do not
reference the same DTC. In this case, message 35
will not appear. If one TermDSM user chooses to
override another by continuing, it is likely that
the overridden TermDSM will produce error messages.
This facility is provided for the case where a
terminal running TermDSM is hung and therefore
cannot exit the program. Note that if one TermDSM
user resets the port of another TermDSM user, this
can cause the system to go down.
---------------------------------------------------------------
36 MESSAGE No ldevs seem to be configured on your system.
(TDSM 356)
CAUSE Necessary configuration information does not exist
on the system.
ACTION Make sure the file NMCONFIG.PUB.SYS exists. Bring
the system down and back up again, making sure that
the proper SYSGEN files are used. (The SYSGEN
files used are determined by the boot path. The
file NMCONFIG.PUB.SYS is used automatically.) If
the problem persists, contact your HP support
representative.
---------------------------------------------------------------
37 MESSAGE The dump process can't find out the length of the
data area. (TDSM 37)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
38 MESSAGE The data area is longer than TermDSM's dump
buffer. (TDSM 38)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
39 MESSAGE TermDSM never received a reply to its dump data
area request. (TDSM 39)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
42 MESSAGE You must have high (1) security to perform this
function. For level 1, you need SM or DI
capability. (TDSM 42)
CAUSE You do not have the correct user capabilities to
use this function.
ACTION Logon as a user with the correct capabilities for
the TermDSM functions you wish to use. Refer to
the reference documentation for the security levels
of each command and subcommand.
---------------------------------------------------------------
43 MESSAGE You can't do this from your own DTC. Please run
TermDSM from another DTC or from the console. (TDSM
43)
CAUSE If you were permitted to selftest, dump, or reset
the DTC to which you are logged on, your session
would be aborted and you would be unable to get the
test results.
ACTION Move to a terminal on another DTC or the system
console to run TermDSM.
---------------------------------------------------------------
44 MESSAGE Warning: This will reset all users on that DTC.
As many as 48 terminal users could be affected.
(TDSM 44)
CAUSE If you continue, all user sessions on this DTC will
be aborted.
ACTION If you want to continue, you should alert all the
users that their sessions will be aborted.
---------------------------------------------------------------
56 MESSAGE Your answer must be at least 1 and no more than
65535. (TDSM 56)
CAUSE The value entered is not in the range 1 to 65535.
ACTION Enter a value in the range. Diagnostic loop counts
are limited to this range.
---------------------------------------------------------------
62 MESSAGE Use the CCTL option (:FILE LIST;DEV=LP;CCTL) when
printing this file. (TDSM 62)
CAUSE Informational message.
ACTION When printing the dump file, use the CCTL option in
the print file equation. This will format the
printed output in an organized way. Printed output
of dump files will be acceptable if they are not
printed with the CCTL option.
---------------------------------------------------------------
64 MESSAGE The following two files make up the DTC dump.
Please deliver both to your HP representative.
(TDSM 64)
CAUSE Informational message.
ACTION Document the problem (the reason you took a dump),
and deliver it to your HP support representative
along with the dump files, preferably on magnetic
tape.
---------------------------------------------------------------
70 MESSAGE There are no DTCs configured on your system.
(TDSM 70)
CAUSE Necessary configuration information does not exist
on the system.
ACTION Check the NMCONFIG.PUB.SYS file for proper DTC
configuration (using :NMMGR). Bring the system down
and back up again. If the problem persists,
contact your HP support representative.
---------------------------------------------------------------
71 MESSAGE There are more DTCs on your system than TermDSM
can reference. Here are the ones TermDSM can
reference. (TDSM 71)
CAUSE You are using more than 32 DTCs on the system. You
will not be able to perform any TermDSM functions
on any DTCs that are not listed in this message.
ACTION Contact your HP support representative.
---------------------------------------------------------------
80 MESSAGE You can't reset your own port or ldev. Please
run TermDSM from a different port or ldev to do
this. (TDSM 80)
CAUSE Verify the ldev numbers entered. If you want to
reset a port, you cannot be logged on to that port;
the operation will abort your session.
ACTION If you want to reset the port you are using, move
to another port or the system console to run
TermDSM.
---------------------------------------------------------------
81 MESSAGE That ldev is unknown (not configured). Please
check the ldev number, or use reset port. (TDSM 81)
CAUSE Although a number was entered in a range that could
be an ldev number, that number is not configured on
the system.
ACTION Verify the ldev number by entering the SHOWJOB
command. You can also reset ports by using the
PORT subcommand (which uses the physical address
instead of the ldev number).
---------------------------------------------------------------
82 MESSAGE You must have high (1) or medium (2) security to
do resets, and high (1) security to reset DTCs.
(TDSM 82) For level 1, you need SM or DI
capability. For level 2, you need SM or DI or OP
capability.
CAUSE You do not have the correct user capabilities to do
this function.
ACTION Logon as a user with the correct capabilities for
the functions you wish to use. Refer to the
reference documentation for the security level of
each command and subcommand.
---------------------------------------------------------------
86 MESSAGE You must have high (1) or medium (2) security to
test ports, and high (1) security to selftest DTCs.
(TDSM 86)
For level 1, you need SM or DI capability. For
level 2, you need SM or DI or OP capability.
CAUSE You do not have the correct user capabilities to do
this function.
ACTION Logon as a user with the correct capabilities for
the TermDSM functions you wish to use. Use the
appropriate reference materials to determine the
security level of each command and subcommand.
---------------------------------------------------------------
93 MESSAGE TermDSM could not open the DTC manager, so the
DTC dump could not be obtained. (TDSM 93)
CAUSE Internal error, unless another TermDSM was being
run against that same DTC and you chose not to
override the other user. There is no error in this
case.
ACTION Contact your HP support representative (if it is an
internal error).
---------------------------------------------------------------
110 MESSAGE You can't test your own port. Please run TermDSM
from another port. (TDSM 110)
CAUSE Doublecheck the numbers entered. If you wish to
test a port, you cannot be logged on to that port;
the operation will abort your session and you will
be unable to obtain the results of the test.
ACTION If you want to test the port to which you are
logged on, move to another port or the system
console to run TermDSM.
---------------------------------------------------------------
113 MESSAGE Please put a loopback hood on the port, before
answering the "How may times?" question. (TDSM 113)
CAUSE The hardware must be present before the diagnostic
is run.
ACTION Refer to the appropriate TermDSM manual for
information on port loopback tests.
---------------------------------------------------------------
114 MESSAGE Please connect and make ready (power on, remote
mode, etc.) a supported terminal, before answering
the "How many times?" question. (TDSM 114)
CAUSE The hardware must be present before the diagnostic
is run.
ACTION Refer to the appropriate TermDSM manual for
information on terminal loopback tests.
---------------------------------------------------------------
115 MESSAGE Please connect and make ready (power on, remote
mode, etc.) a supported printer (or terminal),
before answering the "How many times?" message.
(TDSM 115)
CAUSE The hardware must be present before the diagnostic
is run.
ACTION Refer to the appropriate TermDSM manual for
information on the port test.
---------------------------------------------------------------
121 MESSAGE Warning: The LDM dump is suspect. Consecutive
dumps did not match. (TDSM 121)
CAUSE This message is written to dump files and never
appears as an error message to a user. There was
activity during the dump process, so part of the
dump relating to the Logical Device Manager might
be inconsistent with the rest of the dump.
ACTION Submit the dump to your HP support representative.
---------------------------------------------------------------
122 MESSAGE You can't reset your own SIC. Please run TermDSM
from another SIC or DTC, or from the console. (TDSM
122)
CAUSE Your own session is on this SIC (serial interface
card). If you wish to reset a SIC, you cannot be
logged onto that card; the operation will abort
your session and you will be unable to obtain the
results.
ACTION Move to a port on a different DTC or SIC, or to the
system console, to run TermDSM.
---------------------------------------------------------------
170 MESSAGE The Distributed Terminal Subsystem software does
not exist. Please verify that the NMCONFIG.PUB.SYS
file is correct and validated, and the system has
booted up without errors. This situation prevents
TermDSM from continuing. (TDSM 170)
CAUSE The NMCONFIG.PUB.SYS file does not exist, or has no
DTCs configured.
ACTION Check the NMCONFIG.PUB.SYS file for proper DTC and
terminal configurations (using NMMGR), then
shutdown and restart the system.
---------------------------------------------------------------
200 MESSAGE DTC and mainframe software versions are
incompatible. (TDSM 200)
CAUSE Incompatibilities were found between subsystem
software on the HP 3000 and subsystem software on
the DTC.
ACTION Contact your HP support representative to check the
DTCM and download file versions with NMMAINT. If
this is not the problem, the cause is an internal
error.
---------------------------------------------------------------
201 MESSAGE Bad message length. (TDSM 201)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
203 MESSAGE Invalid operation. (TDSM 203)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
204 MESSAGE Request not supported. (TDSM 204)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
205 MESSAGE Sub request not supported. (TDSM 205)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
206 MESSAGE Entity not supported. (TDSM 206)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
207 MESSAGE No such entity. (TDSM 207)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------
208 MESSAGE No parm for entity. (TDSM 208)
CAUSE Internal error.
ACTION Contact your HP support representative.
---------------------------------------------------------------