HP 3000 Manuals HP 3000 Manuals
(CIERR) (contd)
3023 MESSAGE OUTFENCE HAS 1 TO 3 PARAMETERS: PRIORITY [;LDEV=
DEVICE] (CIERR 3023)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3024 MESSAGE EXPECTED OUTFENCE BETWEEN 1 AND 14. (CIERR 3024)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3025 MESSAGE FENCE > 14, 14 USED. (CIWARN 3025)
CAUSE The OUTFENCE specified was greater than 14.
ACTION None. Information only.
---------------------------------------------------------------
3026 MESSAGE OUTFENCE < 1, 1 USED. (CIWARN 3026)
CAUSE The OUTFENCE specified was less than 1.
ACTION None. Information only.
---------------------------------------------------------------
3027 MESSAGE ABORTIO HAS EXACTLY ONE PARAMETER, THE DEVICE
NUMBER. (CIERR 3027)
CAUSE More than one parameter was specified with ABORTIO.
ACTION Specify only the device number when using ABORTIO.
---------------------------------------------------------------
3028 MESSAGE NO I/O TO ABORT FOR DEVICE !. (CIWARN 3028)
CAUSE There was no inout/output activity to abort on the
device specified with the ABORTIO command.
ACTION None. Information only.
---------------------------------------------------------------
3029 MESSAGE ACCEPT HAS ONLY TWO PARAMETERS. (CIERR 3029)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3030 MESSAGE REFUSE HAS ONLY TWO PARAMETERS. (CIERR 3030)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3031 MESSAGE ACCEPT HAS AT LEAST ONE PARAMETER, THE DEVICE
NUMBER (CIERR 3031)
CAUSE No parameters were specified with ACCEPT.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3032 MESSAGE REFUSE HAS AT LEAST ONE PARAMETER, THE DEVICE
NUMBER (CIERR 3032)
CAUSE No parameters were specified with REFUSE.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3033 MESSAGE COMMA EXPECTED AFTER 'DATA' OR 'JOB'. (CIERR
3033)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3034 MESSAGE EXPECTED ONE OF EITHER DATA OR JOBS. (CIERR 3034)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3035 MESSAGE DEVICE IS NOT DATA OR JOB ACCEPTING. (CIERR 3035)
---------------------------------------------------------------
3036 MESSAGE DEVICE HAS NO DEFAULT OUTPUT DEVICE. (CIERR 3036)
---------------------------------------------------------------
3037 MESSAGE WELCOME DATA SEGMENTS BUSY. (CIERR 3037)
---------------------------------------------------------------
3038 MESSAGE BREAKJOB HAS EXACTLY ONE PARAMETER, THE JOB ID.
(CIERR 3038)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3039 MESSAGE RESUMEJOB HAS EXACTLY ONE PARAMETER, THE JOB ID.
(CIERR 3039)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3040 MESSAGE EXPECTED JOB ID IN THE FORM #Jnnn. (CIERR 3040)
CAUSE The job number was ommitted or not entered
correctly.
ACTION Reenter the command making sure the job number is
entered in the form #Jnnn.
---------------------------------------------------------------
3041 MESSAGE JOB NUMBER MUST BE WITHIN 1 AND 16383. (CIERR
3041)
CAUSE The job number entered was less than 1 or greater
than 16,383.
ACTION Reenter the command using a job number between 1
and 16,383.
---------------------------------------------------------------
3042 MESSAGE JOB DOES NOT EXIST. (CIERR 3042)
CAUSE The job specified with the BREAKJOB command does
not exist.
ACTION Reenter the command using a valid job number.
---------------------------------------------------------------
3043 MESSAGE BREAKJOB REQUIRES JOB TO BE ACTIVE. (CIERR 3043)
CAUSE The job specified with the BREAKJOB command is not
active.
ACTION Use the BREAKJOB command for active jobs only. Use
the SHOWJOB command to determine the state of the
jobs (ACTIVE, READY, etc.).
---------------------------------------------------------------
3044 MESSAGE RESUMEJOB REQUIRES JOB TO BE SUSPENDED. (CIERR
3044)
CAUSE The RESUMEJOB command was issued for a job that was
not suspended with the BREAKJOB command.
ACTION Use the RESUMEJOB command only for jobs suspended
with the BREAKJOB command.
---------------------------------------------------------------
3045 MESSAGE CANT SPECIFY INPRI OF 0 OR 14 WITHOUT AM CAP.
(CIERR 3045)
CAUSE User does not have Account Manager (AM) capability.
ACTION Ask your system manager to assign AM capability to
your user name, or use an INPRI value between 1 and
13.
---------------------------------------------------------------
3046 MESSAGE JOB IN TERMINATION, CANNOT SUSPEND OR RESUME.
(CIERR 3046)
CAUSE The BREAKJOB or RESUMEJOB command was issued
specifying a job that has already been terminated
with the ABORTJOB command.
ACTION Use BREAKJOB for active jobs only; use RESUMEJOB
for suspended jobs only.
---------------------------------------------------------------
3047 MESSAGE JOB SECURITY IS HIGH OR JOB NOT YOURS, CANNOT
SUSPEND, RESUME, ALTER, OR ABORT. (CIERR 3047)
CAUSE The command entered is executable from the console
only unless distributed with the ALLOW command, or
if the JOBSECURITY is set to LOW.
ACTION Issue the command from the console, or have the
operator set JOBSECURITY to LOW.
---------------------------------------------------------------
3048 MESSAGE REPLY HAS AT LEAST TWO PARAMETERS. (CIERR 3048)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3049 MESSAGE REPLY HAS ONLY THREE PARAMETERS. (CIERR 3049)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3050 MESSAGE EXPECTED PROCESS NUMBER BETWEEN 1 AND !. (CIERR
3050)
CAUSE The process number specified is not within the
valid range.
ACTION Reenter the command making sure the process number
specified is within the valid range.
---------------------------------------------------------------
3051 MESSAGE NO REPLY OUTSTANDING FOR PROCESS. (CIERR 3051)
---------------------------------------------------------------
3052 MESSAGE REPLY EXPECTED YES/NO OR NUMBER. (CIERR 3052)
---------------------------------------------------------------
3053 MESSAGE REPLY EXPECTED YES/NO. (CIERR 3053)
---------------------------------------------------------------
3054 MESSAGE REPLY EXPECTED NUMBER. (CIERR 3054)
---------------------------------------------------------------
3055 MESSAGE ASSOCIATE HAS EXACTLY 1 PARAMETER, THE DEVICE
CLASS. (CIERR 3055)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3056 MESSAGE DISASSOCIATE HAS ONLY 1 PARAMETER, THE DEVICE
CLASS. (CIERR 3056)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3057 MESSAGE YOU ALREADY HAVE ASSOCIATED ONE OR MORE DEVICES
IN THAT DEVICE CLASS. (CIERR 3057)
CAUSE A device class was specified with the ASSOCIATE
command that already has one or more devices
associated.
ACTION Refer to the ASSOCIATE command in the MPE/iX
Commands Reference Manual, (32650-90003) for
additional information.
---------------------------------------------------------------
3058 MESSAGE EXECUTING THIS COMMAND REQUIRES PRIOR ASSOCIATION
TO THAT DEVICE CLASS. (CIERR 3058)
CAUSE The DISASSOCIATE command was used for a device
class that has not been associated with the
ASSOCIATE command.
ACTION Use the DISASSOCIATE command only for devices that
have been associated with the ASSOCIATE command.
---------------------------------------------------------------
3059 MESSAGE ASSOCIATING THIS DEVICE REQUIRES SYSTEM MANAGER'S
PERMISSION. (CIERR 3059)
CAUSE The ASSOCIATE command was used for a device class
that has not been defined in the device class/user
association table.
ACTION The system manager must run ASOCTBL.PUB.SYS in
order to create a device class/user association
table.
---------------------------------------------------------------
3060 MESSAGE THIS REPLY EXPECTS ONLY TWO PARAMETERS. (CIERR
3060)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3061 MESSAGE REPLY STRING TOO LONG, ! CHARACTERS AT MOST
EXPECTED. (CIERR 3061)
---------------------------------------------------------------
3062 MESSAGE JOBFENCE HAS EXACTLY ONE PARAMETER, THE JOB
PRIORITY. (CIERR 3062)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3063 MESSAGE EXPECTED JOBFENCE PRIORITY BETWEEN 0 AND 14.
(CIERR 3063)
CAUSE The jobfence priority range specified was not
within the range of 0 and 14.
ACTION Specify a priority between 0 and 14 with the
JOBFENCE command.
---------------------------------------------------------------
3064 MESSAGE PRIORITY < 0, 0 USED. (CIWARN 3064)
CAUSE A negative number was specified as the priority
fence.
ACTION None. Information only.
---------------------------------------------------------------
3065 MESSAGE COMMA EXPECTED BETWEEN REPLY PARAMETERS. (CIERR
3065)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3066 MESSAGE STREAMS HAS EXACTLY ONE PARAMETER, THE DEVICE
NUMBER. (CIERR 3066)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3067 MESSAGE STREAMS DEVICE CANT BE A TERMINAL. (CIERR 3067)
CAUSE The logical device specified with the STREAMS
command is a terminal.
ACTION Any input device except the System Console or
terminals may be used with the STREAMS command,
providing that it was configured as job-accepting
in the SYSGEN dialog.
---------------------------------------------------------------
3068 MESSAGE STREAMS DEVICE NOT DATA AND JOB ACCEPTING. (CIERR
3068)
CAUSE The input device specified with the STREAMS command
was not configured as job-accepting in the SYSGEN
dialog.
ACTION Any input device except the system console or
terminals may be used with the STREAMS command,
providing that it was configured as job-accepting
in the SYSGEN dialog.
---------------------------------------------------------------
3069 MESSAGE CONSOLE HAS AT MOST ONE PARAMETER, THE DEVICE
NUMBER. (CIERR 3069)
CAUSE More than one parameter was specified with the
CONSOLE command.
ACTION Use the CONSOLE command without parameters to
report the current logical device number of the
console, or use with a logical device number to
change the console to a new device.
---------------------------------------------------------------
3070 MESSAGE DEVICE MUST BE JOB ACCEPTING. (CIERR 3070)
CAUSE The input device specified was not configured as
job-accepting in the SYSGEN dialog.
ACTION Any input device except the system console or
terminals may be used with the STREAMS command,
providing that it was configured as job-accepting
in the SYSGEN dialog.
---------------------------------------------------------------
3071 MESSAGE EXPECTED ONE OF JOB OR SESSION LIMIT. (CIERR
3071)
CAUSE The LIMIT command was entered without parameters.
ACTION Use at least one parameter with LIMIT.
---------------------------------------------------------------
3072 MESSAGE LIMIT HAS AT MOST TWO PARAMETERS. (CIERR 3072)
CAUSE Syntax error. More than two parameters were
specified with the LIMIT command.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3073 MESSAGE LIMIT EXPECTS A COMMA BETWEEN PARAMETERS. (CIERR
3073)
CAUSE Syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
3074 MESSAGE EXPECTED SESSION LIMIT BETWEEN 0 AND 32767.
(CIERR 3074)
CAUSE The session limit parameter value specified with
the LIMIT command was not within the valid range of
0 and 32,767.
ACTION Use a value between 0 and 32,767 when specifying
the session limit with the LIMIT command.
---------------------------------------------------------------
3075 MESSAGE EXPECTED JOB LIMIT BETWEEN 0 AND 32767. (CIERR
3075)
CAUSE The job limit parameter value specified with the
LIMIT command was not within the valid range of 0
and 32,767.
ACTION Use a value between 0 and 32,767 when specifying
the job limit with the LIMIT command.
---------------------------------------------------------------
3076 MESSAGE EXPECTED ONE OF JOB NUMBER OR JOB NAME. (CIERR
3076)
CAUSE The job number or job name was ommitted from the
command entry.
ACTION Reenter the command making sure you specify either
the job number or job name.
---------------------------------------------------------------
3077 MESSAGE DEVICE NOT OUTPUT DEVICE. (CIERR 3077)
CAUSE The logical device specified in the command is not
an output device.
ACTION Reenter the command making sure the the logical
device specified is a valid output device.
---------------------------------------------------------------
3078 MESSAGE EXPECTED JOB NUMBER IN FORM OF #Jnnn. (CIERR
3078)
CAUSE The job number was ommitted or not entered in the
correct form.
ACTION Reenter the command making sure the job number is
entered in the form #Jnnn.
---------------------------------------------------------------