HP 3000 Manuals HP 3000 Manuals
(CIERR) (contd.)
1554 MESSAGE USE OF DEVICE CLASS IS INAPPROPRIATE FOR INPUT
FILES. (CIERR 1554)
CAUSE Same as the message.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
1555 MESSAGE DIRECT ACCESS DEVICE MAY NOT BE SPECIFIED.
(CIERR 1555)
CAUSE Same as the message.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
1556 MESSAGE "DEV=" PARAMETER REDUNDANTLY SPECIFIED, LAST
USED. (CIWARN 1556)
CAUSE The DEV parameter was specified more than once.
The system used the last value entered.
ACTION If you want a value other than that used by the
system reenter the command.
---------------------------------------------------------------
1580 MESSAGE SHOWDEV MAY HAVE ONLY ONE PARAMETER, THE DEVICE
NAME OR NUMBER. (CIWARN 1580)
CAUSE Both a device name and device number were specified
with this command.
ACTION Specify either a device name or device number but
not both.
---------------------------------------------------------------
1581 MESSAGE LOGICAL DEVICE NUMBER ! DOES NOT EXIST ON THE
SYSTEM. (CIERR 1581)
CAUSE The logical device number specified is not valid on
this system.
ACTION Specify a valid logical device number.
---------------------------------------------------------------
1582 MESSAGE CLASS NAME "!" IS INVALID, MORE THAN 8 CHARACTERS
LONG. (CIERR 1582)
CAUSE Device class names may not contain more than eight
characters.
ACTION Specify a valid device class name that contains
eight or fewer characters.
---------------------------------------------------------------
1583 MESSAGE LOGICAL DEVICE CLASS "!" CANNOT BE FOUND ON THE
SYSTEM. (CIERR 1583)
CAUSE The logical device class specified is not valid on
this system.
ACTION Specify a valid logical device class.
---------------------------------------------------------------
1584 MESSAGE DS DEVICE MAY NOT BE SPECIFIED. (CIERR 1584)
CAUSE Same as the message.
ACTION Contact your system manager for the correct LDEV
number or device name.
---------------------------------------------------------------
1585 MESSAGE THERE ARE NO DEVICES CONFIGURED IN DEVICE CLASS
"!". (CIWARN 1585)
CAUSE Same as the message.
ACTION Contact your system manager for the correct device
class name.
---------------------------------------------------------------
1590 MESSAGE STREAM FILE MAY NOT BE A SYSTEM DEFINED FILE.
(CIERR 1590)
CAUSE Same as the message.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
1591 MESSAGE EXPECTED JUST ONE CHARACTER AS COLON PROMPT
REPLACEMENT. (CIERR 1591)
CAUSE More than one special character was used as a
replacement for the colon prompt.
ACTION Specify only one special character as a replacement
for the colon prompt in the JOB command. By
default the system expects the ! character to be
used.
---------------------------------------------------------------
1593 MESSAGE I/O ERROR WHILE READING IN JOB TO BE STREAMED.
(CIERR 1593)
CAUSE Same as the message.
ACTION Check the job file for syntax errors. Make any
corrections (see "JOB" command in the MPE/iX
Commands Reference Manual, (32650-90003) and STREAM
the file again.
---------------------------------------------------------------
1594 MESSAGE ERROR IN WRITING TO SPOOL FILE. SPOOLING STOPPED.
(CIERR 1594)
CAUSE Same as the message.
ACTION Contact your system manager to correct the spool
queues.
---------------------------------------------------------------
1595 MESSAGE UNABLE TO OPEN SPOOL FILE. (CIERR 1595)
CAUSE Same as the message.
ACTION Contact your system manager to correct the spool
queues.
---------------------------------------------------------------
1596 MESSAGE UNABLE TO OPEN STREAM FILE. (CIERR 1596)
CAUSE Same as the message.
ACTION Contact your system manager to perform the STREAMS
command.
---------------------------------------------------------------
1597 MESSAGE COMMAND GREATER THAN 255 CHARACTERS. (CIERR 1597)
CAUSE The maximum number of characters MPE/iX allows in a
command is 255.
ACTION Specify a command line that contains no more than
255 characters.
---------------------------------------------------------------
1598 MESSAGE MISSING COLON ON CONTINUATION LINE. (CIERR 1598)
CAUSE You entered a syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
1599 MESSAGE UNABLE TO CLOSE STREAM FILE. (CIERR 1599)
CAUSE Same as the message.
ACTION None; the message is for information only.
---------------------------------------------------------------
1610 MESSAGE EXPECTED A JOB NUMBER BETWEEN 1 AND 16383 (CIERR
1610)
CAUSE The job number specified was not between 1 and
16383.
ACTION Specify a value between 1 and 16383 for a job
number.
---------------------------------------------------------------
1611 MESSAGE EXPECTED A SESSION NUMBER BETWEEN 1 AND 16383.
(CIERR 1611)
CAUSE The session number specified was not between 1 and
16383.
ACTION Specify a value between 1 and 16383 for a session
number.
---------------------------------------------------------------
1612 MESSAGE EXPECTED "S" INDICATING SESSION. (CIERR 1612)
CAUSE You entered a syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
1613 MESSAGE EXPECTED "@S". (CIERR 1613)
CAUSE You entered a syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
1614 MESSAGE EXPECTED "@" OR A PARTICULAR JOB NAME. (CIERR
1614)
CAUSE You entered a syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
1615 MESSAGE JOB NAME MAY NOT EXCEED 8 CHARACTERS. (CIERR
1615)
CAUSE The specified job name was more than eight
characters.
ACTION Specify a job name that contains eight or fewer
characters.
---------------------------------------------------------------
1616 MESSAGE JOB NAME MUST START WITH ALPHABETIC CHARACTER.
(CIERR 1616)
CAUSE The job name specified did not begin with an
alphabetic character.
ACTION Specify a job name that begins with an alphabetic
character.
---------------------------------------------------------------
1617 MESSAGE "." REQUIRED BETWEEN USER AND ACCOUNT NAMES.
(CIERR 1617)
CAUSE The system expects a period to separate (delimit)
the user and the account name.
ACTION Use a period as a delimiter between the user name
and the account name (user.account).
---------------------------------------------------------------
1618 MESSAGE TELL COMMAND REQUIRES THE ID OF THE JOB TO BE
TOLD. (CIERR 1618)
CAUSE You entered a syntax error.
ACTION Check the syntax and reenter the command.
---------------------------------------------------------------
1619 MESSAGE THERE WAS NO SESSION FOUND WHICH MATCHED THIS ID.
(CIWARN 1619)
CAUSE The session number or session name specified is not
valid.
ACTION Determine the correct session number or session
name with the SHOWJOB command and issue command
again.
---------------------------------------------------------------
1620 MESSAGE THE SENDER IS THE ONLY QUALIFYING TARGET. NO
MESSAGE SENT. (CIWARN 1620)
CAUSE You are the only user who is able to receive this
message and you cannot send a message to yourself.
ACTION Specify a valid session to receive the message.
---------------------------------------------------------------
1626 MESSAGE SOME SORT OF I/O ERROR IN SENDING MESSAGE TO
CONSOLE. (CIERR 1626)
CAUSE An error occurred in sending the message to the
console.
ACTION Send a new message to the console.
---------------------------------------------------------------
1627 MESSAGE ! NOT INTERACTIVE; MESSAGE NOT SENT TO JOB
(CIWARN 1627).
CAUSE You cannot send a message to a job.
ACTION Only send messages to interactive sessions.
---------------------------------------------------------------
1628 MESSAGE LOGON DEVICE ACCESS SECURITY VIOLATION (CIERR
1628).
---------------------------------------------------------------
1630 MESSAGE TARGET FILE IS THE ONLY PARAMETER ALLOWED.
(CIERR 1630)
CAUSE The only valid parameter is the target file.
ACTION Specify a valid target file.
---------------------------------------------------------------
1631 MESSAGE TARGET FILE IS A REQUIRED PARAMETER. (CIERR
1631)
CAUSE The target file was not specified.
ACTION Specify a valid target file.
---------------------------------------------------------------
1632 MESSAGE UNABLE TO OPEN PERMANENT DISK FILE !. (CIERR
1632)
CAUSE Same as the message.
ACTION Contact your system manager to check for disk
allocation.
---------------------------------------------------------------
1633 MESSAGE FILE SYSTEM ERROR ! WHILE READING PAPER TAPE.
(CIERR 1633)
CAUSE Same as the message.
ACTION Refer to the File System error message section.
---------------------------------------------------------------
1634 MESSAGE FILE SYSTEM ERROR ! WHILE WRITING TO DISK FILE.
(CIERR 1634)
CAUSE Same as the message.
ACTION Refer to the File System error message section.
---------------------------------------------------------------
1635 MESSAGE FILE SYSTEM ERROR ! WHILE CLOSING DISK FILE.
(CIERR 1635)
CAUSE Same as the message.
ACTION Refer to the File System error message section.
---------------------------------------------------------------
1636 MESSAGE UNABLE TO ACCESS PAPER TAPE READER ON TERMINAL.
(CIERR 1636)
CAUSE Same as the message.
---------------------------------------------------------------
1640 MESSAGE THE ONLY PARAMETERS ARE THE INPUT AND OUTPUT
SPEEDS. (CIERR 1640)
CAUSE Specifying parameters other than the input speed
and output speed is not allowed.
ACTION Specify only the input speed and output speed with
this command.
---------------------------------------------------------------
1641 MESSAGE SPEED REQUIRES EITHER AN INPUT OR AN OUTPUT
SPEED. (CIERR 1641)
CAUSE The SPEED command requires either an INPUT or an
OUTPUT speed to be specified.
ACTION Specify either an INPUT or an OUTPUT speed with the
SPEED command.
---------------------------------------------------------------
1642 MESSAGE INPUT SPEED SPECIFIED NOT SUPPORTED BY THIS
DEVICE. (CIERR 1642)
CAUSE The terminal you are using does not support the
INPUT speed you specified.
ACTION Specify a valid INPUT speed.
---------------------------------------------------------------
1643 MESSAGE OUTPUT SPEED SPECIFIED NOT SUPPORTED BY THIS
DEVICE. (CIERR 1643)
CAUSE The terminal you are using does not support the
OUTPUT speed you specified.
ACTION Specify a valid OUTPUT speed.
---------------------------------------------------------------
1644 MESSAGE SPEED CHANGE NOT VERIFIED - OLD SPEED RETAINED.
(CIWARN 1644)
CAUSE The SPEED change you specified was not verified by
the system and the existing SPEED specification
will be used.
ACTION Verify the SPEED change by entering MPE Return at
the terminal. If the characters MPE cannot be
verified, the system assumes that the terminal is
to continue at the old speed.
---------------------------------------------------------------
1645 MESSAGE INPUT SPEED MUST EQUAL OUTPUT SPEED FOR THIS
SYSTEM. WILL ATTEMPT TO CHANGE BOTH SPEEDS TO VALUE
SPECIFIED. (CIWARN 1645)
CAUSE The value specified for INPUT and OUTPUT were not
the same, which is required on this system. The
system attempts to set SPEED to equal values.
ACTION Specify the same value for both INPUT and OUTPUT.
---------------------------------------------------------------
1646 MESSAGE INPUT AND OUTPUT SPEEDS MUST BE EQUAL ON THIS
SYSTEM. (CIERR 1645)
CAUSE The value specified for INPUT and OUTPUT were not
the same, which is required on this system.
ACTION Specify the same value for both INPUT and OUTPUT.
---------------------------------------------------------------
1649 MESSAGE EXPECTED ONE PARAMETER EITHER "ON" OR "OFF".
COMMAND IGNORED (CIERR 1649)
CAUSE This command expects you to specify either ON or
OFF.
ACTION Specify either ON or OFF with this command.
---------------------------------------------------------------
1650 MESSAGE ALLOCATE HAS ONLY TWO PARAMETERS. (CIERR 1650)
CAUSE The parameter specified is not allowed with the
ALLOCATE command.
ACTION The ALLOCATE command only accepts the procedure or
program name parameters.
---------------------------------------------------------------
1651 MESSAGE REQUIRES AT LEAST A PROGRAM NAME. (CIERR 1651)
CAUSE No program name was specified.
ACTION Specify a program name to be allocated.
---------------------------------------------------------------
1652 MESSAGE PROCEDURE NOT ALLOCATED. (CIWARN 1652)
CAUSE Procedure not allocated because the files reside on
a non-system domain (volume set) or the allowed
number of entries in the code segment table has
been exceeded.
ACTION Contact your system manager.
---------------------------------------------------------------
1653 MESSAGE PROCEDURE ALREADY ALLOCATED. (CIWARN 1653)
CAUSE The procedure specified is already allocated.
ACTION None.
---------------------------------------------------------------
1654 MESSAGE PROGRAM NOT ALLOCATED. (CIWARN 1654)
CAUSE Program not allocated because the files reside on a
non-system domain (volume set) or the allowed
number of entries in the code segment table has
been exceeded.
ACTION Contact your system manager.
---------------------------------------------------------------
1655 MESSAGE PROGRAM ALREADY ALLOCATED. (CIWARN 1655)
CAUSE The program specified is already allocated.
ACTION None.
---------------------------------------------------------------
1656 MESSAGE EXPECTED EITHER "PROGRAM" OR "PROCEDURE". (CIERR
1656)
CAUSE A program name or procedure name must be specified
with the ALLOCATE command.
ACTION Specify a valid program or procedure name with the
command.
---------------------------------------------------------------
1657 MESSAGE PROGRAM FILE MAY NOT BE A FILE EQUATED FILE NAME.
(CIERR 1657)
CAUSE Same as the message.
ACTION Reenter the command using a "non-backreferenced"
file name. Do not enter a file name that has an
asterisk (*) at the beginning of it, since that
indicates that it refers to a file equation.
---------------------------------------------------------------
1658 MESSAGE PROGRAM FILE MAY NOT BE A SYSTEM DEFINED FILE.
(CIERR 1658)
CAUSE Same as the message.
ACTION None; the message is for information only.
---------------------------------------------------------------