HP 3000 Manuals HP 3000 Manuals
FMT Errors
Listed below are the messages that are generated by the Link Trace
Formatter. They are displayed on the user terminal when running NMDUMP.
If you must submit an SR or call your HP representative,please copy the
error exactly as it appears on the terminal; it will make determining the
CAUSE of the problem easier. These messages are not logged.
The messages are listed below in numerical order according to error
number.
995 MESSAGE SUBSYSxxTRACEFORMAT CM STUB ERROR (nnn,sss) FROM
HPLOADNMPROC UNABLE TO CALL NM TRACE FORMATTER
ROUTINE (FMTERR 995)
CAUSE The CM Stub could not load an NM WAN Trace
Formatter routine for subsystem "xx" from the
system library XL.PUB.SYS.
ACTION Incorrect software installation to run
Native-Mode Trace Formatters. The SWITCH error
number is "nnn" and the subsystem reporting the
error is "sss". Call your HP representative.
--------------------------------------------------------------------------
996 MESSAGE SUBSYSTEM_xx_MENU CM STUB ERROR (nnn,sss) FROM
HPSWTONMNAME UNABLE TO CALL NM MENU ROUTINE
(FMTERR 996)
CAUSE The CM Stub could not call the named NM WAN
Trace Formatter options menu routine for
subsystem "xx" in the system library XL.PUB.SYS.
ACTION Incorrect software installation to run
Native-Mode Trace Formatters. This could also
be CAUSEd by incorrect privilege levels. The
SWITCH error number is "nnn" and the subsystem
reporting the error is "sss". Call your HP
representative.
--------------------------------------------------------------------------
998 MESSAGE SUBSYSxxTRACEFORMAT CM STUB ERROR (nnn,sss) FROM
HPSWTONMPLABEL UNABLE TO CALL NM TRACE FORMATTER
ROUTINE (FMTERR 998)
CAUSE The CM stub successfully loaded the NM WAN Trace
Formatter routine for subsystem "xx" from the
system library "XL.PUB.SYS", but could not call
it.
ACTION Incorrect software installation to run
Native-Mode Trace Formatters. This could also
be CAUSEd by incorrect privilege levels or a bug
in the NM WAN Trace Formatter CM Stub. The
SWITCH error number is "nnn" and the subsystem
reporting the error is "sss". Call your HP
representative.
--------------------------------------------------------------------------
999 MESSAGE SUBSYSxxTRACEFORMAT CM STUB ERROR (nnn,sss) FROM
HPSWTONMNAME UNABLE TO CALL NM TRACE FORMATTER
ROUTINE (FMTERR 999)
CAUSE The CM Stub could not call the named NM WAN
Trace Formatter routine for subsystem "xx" in
the system library XL.PUB.SYS.
ACTION Incorrect software installation to run
Native-Mode Trace Formatters. This could also
be CAUSEd by incorrect privilege levels. The
SWITCH error number is "nnn" and the subsystem
reporting the error is "sss". Call your HP
representative.
--------------------------------------------------------------------------
4024 MESSAGE ALL overrides other selections entered at the
same time
CAUSE Among the filter-set numbers you entered, you
also specified the number for ALL. This is a
warning.
ACTION Check your input. Unless you mistyped one of
the other set-numbers, it does not make sense to
specify ALL along with other items, beCAUSE ALL
would include the other sets anyway. To retype
your input after this warning you must first
return to the filter-sets selection menu.
--------------------------------------------------------------------------
4025 MESSAGE Warning: Errors always print; for "Errors only"
don't include other sets
CAUSE Among the filter-set numbers you entered, you
also specified the number for ERRORS-ONLY. This
is a warning.
ACTION Check your input. Unless you mistyped one of
the other set-numbers, it does not make sense to
specify ERRORS-ONLY along with other items,
beCAUSE including the other items would defeat
the meaning of ERRORS-ONLY. To retype your input
after this warning you must first return to the
filter-sets selection menu.
--------------------------------------------------------------------------
4026 MESSAGE Input truncated to 80 characters
CAUSE The input file to the user menu was given more
than 80 characters of input, but the menu can
only accept 80. This is a warning.
ACTION If the extra characters are just extra blanks,
ignore this message or reduce the width of the
input file. But if the extra characters are
non-blank, you must edit the input file, finding
a way to reduce the width of the input data to
no more than 80 characters.
--------------------------------------------------------------------------
4027 MESSAGE Extra input ignored
CAUSE Only one number was expected, but you entered
more than one, and the extra number(s) were
ignored. This is a warning.
ACTION Check your input and, if necessary, return to
that prompt and retype the input.
--------------------------------------------------------------------------
4028 MESSAGE Range error at position shown; other values
accepted if allowed
CAUSE One of the numbers you entered was out of range;
a "^^" indicator appears below the illegal
number. The number entered was probably much
too large.
ACTION The bad value was not accepted. You may press
the Return key to keep the other values on the
same line, or else retype the entire input using
only legal values.
--------------------------------------------------------------------------
4029 MESSAGE Syntax error at position shown; other values
accepted if allowed
CAUSE Some of the numbers on the input line contained
illegal characters, or were separated by illegal
characters. Legal inputs are digits 0-9 and the
question mark ?. Legal separators for a list
are the comma , and the blank ".
ACTION Retype the input.
--------------------------------------------------------------------------
4030 MESSAGE Invalid set number NN; reenter all or hit RETURN
to keep others
CAUSE One of the filter-set numbers you selected is
not one of the valid filter sets for this
formatter.
ACTION Check your input against the available sets
shown in the menu. You may press the Return key
to keep the other number(s) you entered on the
same line, or you may retype the entire input.
You may also return to the main menu and "set
all options back to their default values."
--------------------------------------------------------------------------
4031 MESSAGE Output limit out of range; enter another number
or hit RETURN
CAUSE You have selected a value which is less than the
lower output limit or greater than the upper
output limit.
ACTION The value you selected was not accepted.
Reenter a value which is within the range shown
in the prompt. The prompt is meant as a
reminder; values up to 4096 are also legal.
--------------------------------------------------------------------------
4032 MESSAGE Invalid option number NN ignored; others
accepted
CAUSE One of the option numbers you selected at the
main menu was not a valid option number for this
formatter.
ACTION The illegal option number was ignored, but any
other options on the same line were executed.
Check your input and retype if necessary.
--------------------------------------------------------------------------
4033 MESSAGE Number of inputs exceeds storage capacity, rest
ignored
CAUSE Bug in Trace-Formatter numeric input processing.
The formatter could not process all the numbers
entered by the user.
ACTION Check your input and retype if necessary. If
the problem continues to occur, submit an HP
Service Request form against the Trace
Formatter, specifying the input you tried and
the subsystem you were trying to format. A
temporary solution might be to type fewer
numbers.
--------------------------------------------------------------------------
4034 MESSAGE CIERROR NNNN while executing MPE command
CAUSE The MPE command you tried encountered an error.
MPE returned error number NNNN to the Formatter
(MPE warnings are ignored).
ACTION Check your input. If necessary, retype the MPE
command. You may look up the Command
Interpreter error number in the NS3000/iX Error
Messages Reference Manual.
--------------------------------------------------------------------------
4035 MESSAGE MISSING OPT EXECUTOR #NN; PLEASE SUBMIT HP
SERVICE REQUEST
CAUSE Bug in Trace-Formatter option-execution
processing. The formatter recognized an option
you typed, but could not find processing for
that option.
ACTION Submit an HP Service Request form against the
formatter, specifying what input you typed and
what subsystem you were trying to format.
--------------------------------------------------------------------------
none MESSAGE MISSING MESSAGE #NNNN
CAUSE Bug in Trace-Formatter error message processing.
The explanatory text for error number NNNN is
missing from the formatter.
ACTION Submit an HP Service Request form against the
Formatter, specifying what input you typed and
what subsystem you were trying to format.
--------------------------------------------------------------------------