HP 3000 Manuals HP 3000 Manuals
Info String Error Messages (PTINFOERR)
The following PTINFOERR error messages appear whenever an error occurs in
the info string of the RUN command used to start Pass Thru or issue
printer commands. If a PTINFOERR message is generated, correct the info
string and reenter the command.
---------------------------------------------------------------------------------------
PTINFOERR 2 MESSAGE Configuration file parameter omitted. (PTINFOERR 2)
CAUSE The configuration file (config) parameter was omitted
from the info string.
ACTION See chapter 3 for information about info string
parameters, and then reenter your command.
---------------------------------------------------------------------------------------
PTINFOERR 3 MESSAGE Invalid configuration file parameter specified.
(PTINFOERR 3)
CAUSE The configuration file parameter (config) specified in
the info string is invalid.
ACTION See chapter 3 for information about info string
parameters, and then reenter your command.
---------------------------------------------------------------------------------------
PTINFOERR 4 MESSAGE Invalid LDEV parameter. (PTINFOERR 4)
CAUSE The ldev parameter specified in the info string is
invalid.
ACTION See chapter 3 for information about info string
parameters, and then reenter your command.
---------------------------------------------------------------------------------------
PTINFOERR 5 MESSAGE Invalid DEVID parameter. (PTINFOERR 5)
CAUSE The devid parameter specified in the info string is
invalid.
ACTION See chapter 3 for information about info string
parameters, and then reenter your command.
---------------------------------------------------------------------------------------
PTINFOERR 10 MESSAGE Node Management Monitor (NMMON) was unable to create Pass
Thru. (PTINFOERR 10)
CAUSE The Node Management Monitor (NMMON) was unable to create
Pass Thru.
ACTION See chapter 3 for information about info string
parameters, check your info string, and then reenter your
command.
---------------------------------------------------------------------------------------
PTINFOERR 11 MESSAGE The FORMAT parameter must be 1, 2, 3 or 4. (PTINFOERR 11)
CAUSE The format parameter specified in the info string is
invalid.
ACTION The format parameter must be 1, 2, 3 or 4.
---------------------------------------------------------------------------------------
PTINFOERR 12 MESSAGE The PRIORITY or SPRIORITY parameter must be an integer
between 1 and 13. (PTINFOERR12)
CAUSE Either the priority or spriority parameter specified in
the info string is invalid.
ACTION The priority and spriority parameters must be integers
from 1 through 13. Modify your info string and try
again.
---------------------------------------------------------------------------------------
PTINFOERR 13 MESSAGE The ENHANCE parameter must be 0, 1, 2, or 3. (PTINFOERR
13)
CAUSE The enhance parameter specified in the info string is
invalid.
ACTION The enhance parameter must be 0, 1, 2, or 3. Modify
your info string and try again.
---------------------------------------------------------------------------------------
PTINFOERR 14 MESSAGE The READTO parameter must be an integer between 10 and
255. (PTINFOERR 14)
CAUSE The readto parameter specified in the info string is
invalid.
ACTION The readto parameter must be an integer from 10 through
255. Modify your info string and try again.
---------------------------------------------------------------------------------------
PTINFOERR 17 MESSAGE An HP LAN nodename must be from one to eight characters
in length and begin with an alphabetic character.
(PTINFOERR 17)
CAUSE The HP LAN node name that was specified is invalid.
ACTION Modify the node name so it begins with an alphabetic
character and is not more than eight characters in
length. Refer to the HP SNA Server/Access User's Guide
for more information.
---------------------------------------------------------------------------------------
PTINFOERR 18 MESSAGE The SNA Server must be installed properly to use this
feature. (PTINFOERR 18)
CAUSE You entered either a colon and a node name, or both, in
your info string, but the SNA Server cannot provide
service because it is not properly installed.
ACTION Check with your HP representative to make sure the SNA
Server is properly installed. Refer to the HP SNA
Server/Access User's Guide for more information.
---------------------------------------------------------------------------------------
PTINFOERR 19 MESSAGE A user and account must be specified for printer
emulation on a LAN. (PTINFOERR 19)
CAUSE The node name and logical device number in your info
string must be qualified by a logon to that system.
ACTION Specify a user and account in brackets after the node
name in the ldev specification of your info string.
Refer to the HP SNA Server/Access User's Guide for more
information.
---------------------------------------------------------------------------------------
PTINFOERR 20 MESSAGE Unable to find ']' indicating end of user and account
logon. (PTINFOERR 20)
CAUSE SNA IMF was unable to find "]" character indicating end
of user and account logon.
ACTION Enter the right-hand bracket (]) after your user and
account specification. Refer to the HP SNA Server/Access
User's Guide for more information.
---------------------------------------------------------------------------------------
PTINFOERR 21 MESSAGE Too many characters were specified for user and account.
Up to 62 characters may be entered. (PTINFOERR 21)
CAUSE More than 62 characters were used to specify your user
and account logon. Only 62 characters are allowed for
session, user.account.group.
ACTION Use 62 characters or less to specify your user and
account logon in the ldev parameter.
---------------------------------------------------------------------------------------
PTINFOERR 22 MESSAGE A command must be SHOW, SEND, or SET. (PTINFOERR 22)
CAUSE The SHOW, SEND, or SET command was expected.
ACTION Issue a SHOW, SEND, or SET command as specified in
chapter 6 of this manual, under "Entering Printer
Commands and Adjusting Page Length."
---------------------------------------------------------------------------------------
PTINFOERR 23 MESSAGE The request must be one of HOLD, ENABLE, PA1, PA2,
CANCEL, or CLOSE. (PTINFOERR 23)
CAUSE One of the following keys was expected: HOLD, ENABLE,
PA1, PA2, CANCEL, or CLOSE.
ACTION Issue a SEND command as specified in chapter 6 of this
manual under "Entering Printer Commands and Adjusting
Page Length."
---------------------------------------------------------------------------------------
PTINFOERR 24 MESSAGE An NAU must be from one to eight characters in length and
begin with an alphabetic character. (PTINFOERR 24)
CAUSE Your NAU name was greater than eight characters in length
or began with a digit or a special character.
ACTION Modify your NAU name so it is from one through eight
characters in length and begins with a letter (a through
z). See "Entering Printer Commands and Adjusting Page
Length," in chapter 6 of this manual.
---------------------------------------------------------------------------------------
PTINFOERR 25 MESSAGE Invalid SEND parameter(s). The syntax is SEND key TO
nau. (PTINFOERR 25)
CAUSE Incorrect syntax was specified for the request when
attempting to send a key to an LU.T1 printer.
ACTION Correct the syntax of the request and try again. See
"Entering Printer Commands and Adjusting Page Length," in
chapter 6 of this manual.
---------------------------------------------------------------------------------------
PTINFOERR 26 MESSAGE Invalid SHOW parameter(s). The syntax is SHOW nau.
(PTINFOERR 26)
CAUSE Incorrect syntax was specified for the request when
attempting to display printer session status.
ACTION Correct the syntax of the request and try again. See
"Entering Printer Commands and Adjusting Page Length," in
chapter 6 of this manual.
---------------------------------------------------------------------------------------
PTINFOERR 27 MESSAGE Invalid SET parameter(s). The syntax is SET variable =
value FOR nau. (PTINFOERR 27)
CAUSE Incorrect syntax was specified for the request when
attempting to use the SET command for an SNA IMF printer.
ACTION Correct the syntax of the request and try again. See
"Entering Printer Commands and Adjusting Page Length," in
chapter 6 of this manual.
---------------------------------------------------------------------------------------
PTINFOERR 28 MESSAGE The SET variable must be PAGE. (PTINFOERR 28)
CAUSE Invalid syntax used in the SET command. PAGE is the only
valid variable.
ACTION Correct the syntax of the request and try again. See
"Entering Printer Commands and Adjusting Page Length," in
chapter 6 of this manual.
---------------------------------------------------------------------------------------
PTINFOERR 29 MESSAGE The SET value is out of range. (PTINFOERR 29)
CAUSE The value specified for the SET function is out of range.
ACTION Correct the value specified and try again. See "Entering
Printer Commands and Adjusting Page Length," in chapter 6
of this manual.
---------------------------------------------------------------------------------------
PTINFOERR 30 MESSAGE Your request was not sent because the NAU(s) specified
could not be found. (PTINFOERR 30)
CAUSE The SEND or SET command could not be executed because an
invalid NAU was specified.
ACTION Obtain the correct NAU number via the SHOW command and
try again.
---------------------------------------------------------------------------------------
PTINFOERR 31 MESSAGE The specified NAU(s) could not be found. (PTINFOERR 31)
CAUSE The NAU specified in your printer command could not be
found.
ACTION Verify the NAU numbers via the SHOW command and try
again.