HP 3000 Manuals HP 3000 Manuals
Validation Messages
Listed below are the messages that might occur when you validate the NRJE
configuration data. They are listed in numerical order according to
message number. Configuration file validation is discussed in Chapter 3
of this manual.
---------------------------------------------------------------------------------------
NRJEVAL MESSAGE Configuration file corrupt. Missing NRJE path.
ERR 3 (NRJEVALERR 3)
CAUSE The SNA NRJE path is missing from the configuration
file.
ACTION Create a new configuration file.
---------------------------------------------------------------------------------------
NRJEVAL MESSAGE Configuration file corrupt. Missing NRJE version.
ERR 4 (NRJEVALERR 4)
CAUSE No version stamp exists for the SNA NRJE path.
ACTION Create a new configuration file.
---------------------------------------------------------------------------------------
NRJEVAL MESSAGE No configuration data exists for NRJE subsystem.
WARN 5 (NRJEVALWARN 5)
CAUSE No data is configured for SNA NRJE. Note that this
is a warning message.
ACTION If you do not want SNA NRJE to be configured, no
action is necessary. If you want NRJE to be
configured, you must configure it before validating
the configuration file again.
---------------------------------------------------------------------------------------
NRJEVAL MESSAGE Path: !
ERR 6 Path name not found. (NRJEVALERR 6)
CAUSE The indicated path cannot be found in the
configuration file.
ACTION Ensure that the configuration data indicated in the
path (for example, wsid or writername) is
correctly configured. If it is, contact your HP
representative.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 7 No data found in path record. (NRJEVALERR 7)
CAUSE No data is in the record for the indicated path.
ACTION Ensure that data is configured for the indicated
path. If it is, contact your HP representative.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 8 Node "!" is not configured under SNANODE screen.
(NRJEVALERR 8)
CAUSE A node listed as a configured SNA NRJE node was not
configured as an SNA node.
ACTION Configure the indicated node as an SNA node on the
SNA Node Configuration screen.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 9 Logical device "!" is not a valid NRJE reader.
(NRJEVALERR 9)
CAUSE The indicated ldev is invalid for the reader
indicated in the path. This usually happens when
the ldev is already configured for another
subsystem.
ACTION Configure the correct ldev for the reader in the
Logical Device field of the NRJE Configuration:
Reader Data screen. Remember that you should not
configure the same reader ldev for workstations
that might be simultaneously active.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 10 Lookup table is not configured under PAGE2 screen.
(NRJEVALERR 10)
CAUSE A formid is configured in the Output Destination
field of the NRJE Configuration: Writer Data
screen, but a lookup table is not configured in the
Formid Lookup Table File field of the NRJE
Configuration: Workstation Data Page 2 screen.
ACTION If you want a lookup table to be used, ensure that
a table is correctly configured on the NRJE
Configuration: Workstation Data Page 2 screen. If
you do not want a lookup table to be used, ensure
that a formid is not configured on the NRJE
Configuration: Writer Data screen.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
WARN 11 LUs not validated. Invalid SNAnode "!".
(NRJEVALWARN 11)
CAUSE This error is related to NRJEVALERR 8. If an
invalid node name is specified on the NRJE
Configuration: Workstation Data screen, the LUs
cannot be validated. Note that this is a warning
message.
ACTION Ensure that the indicated SNA node name is correct.
If it is, contact your HP representative.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 12 LU "!" is not configured for SNAnode "!".
(NRJEVALERR 12)
CAUSE The indicated LU is not configured under the
indicated SNA node.
ACTION Ensure that the LU should be configured under the
SNA node. If it should be configured, configure it
on the SNA Configuration: PU and LU Data screen.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 13 No writers are configured. (NRJEVALERR 13)
CAUSE No writer is configured for the workstation
indicated in the path.
ACTION Configure at least one writer for the workstation
on the NRJE Configuration: Writer List screen.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 14 Logging subsystem "SUB0002" is not configured.
(NRJEVALERR 14)
CAUSE The logging subsystem for SNA NRJE is not
configured.
ACTION Configure the SNA NRJE logging subsystem (SUB0002)
on the Logging Configuration screen.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 15 Logging class "!" is not configured. (NRJEVALERR
15)
CAUSE The indicated SNA NRJE logging class is not
configured.
ACTION Configure the indicated SNA NRJE logging class on
the Logging Configuration: Logging Classes screen.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 16 Unknown error occurred while getting this path.
(NRJEVALERR 16)
CAUSE An unexpected error occurred while attempting to
obtain a path from the configuration file. This
usually indicates a problem with the validation
procedure.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------
NRJEVAL MESSSAGE Path: !
ERR 17 Unknown error occurred while reading the path data.
(NRJEVALERR 17)
CAUSE An unexpected error occurred while attempting to
read data from the configuration file. This
usually indicates a problem with the validation
procedure.
ACTION Contact your HP representative.
---------------------------------------------------------------------------------------