HP 3000 Manuals HP 3000 Manuals
X.25 Link QLLC Internal Error Codes
Listed below are the codes that are generated by the X.25 link Qualified
Logical Link Control (QLLC) module when a QLLC internal error occurs.
They are listed in numerical order according to the ProcNum displayed as
part of these SNA Transport logging messages:
Link connect failure on node NodeName
subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
Link failure, recovery in progress on node NodeName
subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
Link failure, shutting down the node NodeName
subsystem = SubsysID, procedure = ProcNum, error num = ErrorNum
The logging messages are described in "SNA Transport Logging Messages"
earlier in this appendix. The X.25 link-related ErrorNum values are
described in "X.25 Link Failure Error Codes" earlier in this appendix.
-1 MESSAGE NETIPC ERROR DETECTED
CAUSE The QLLC module was informed of a socket error
(SOCKERR) by NETIPC.
ACTION Note the socket error number and see the
NS3000/XL Error Messages Reference Manual
(36923-61000) for socket error information.
--------------------------------------------------------------------------
-2 MESSAGE AFT ERROR
CAUSE The QLLC module encountered an error while
trying to obtain the available file table (AFT).
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-3 MESSAGE INSTALLATION ERROR
CAUSE The SNA/X.25 Link IOWAIT completor is not
installed on the system.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-4 MESSAGE QLLC PORT CREATION ERROR
CAUSE The QLLC module encountered an error while
trying to create its IOWAIT port.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-5 MESSAGE PORT SUBQUEUE ERROR
CAUSE The QLLC module encountered an error while
trying to enable its IOWAIT port subqueues.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-6 MESSAGE (reserved for internal use only)
through-16
CAUSE An internal error has occurred.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-17 MESSAGE CALL REJECTED DUE TO SECURITY VIOLATION
CAUSE An incoming SVC call was rejected by SNA/X.25
because the caller was unauthorized. That is,
the caller's address was not included in the
call packet, or it was not the remote address
the SNA node is configured for.
ACTION Verify that the Remote's X.25 Network Address
field of the "SNA Node Configuration: X.25 Link
Data" screen contains the correct X.25 address
for the host node. Also verify that the DIALNO
operand of the PATH macro in the host's switched
major node definition contains the IBM's X.25
address and the HP 3000's X.25 address.
--------------------------------------------------------------------------
-18 MESSAGE (reserved for internal use only)
CAUSE An internal error has occurred.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-19 MESSAGE SECURITY VIOLATION
CAUSE A non-system process tried to launch the QLLC
module.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-20 MESSAGE RECEIVED INVALID QLLU
CAUSE An unrecognizable QLLC control frame (QLLU) was
received from the remote system.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-21 MESSAGE INFO FIELD NOT ALLOWED
CAUSE A QLLU that information fields are not allowed
for was received with an information field.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-22 MESSAGE INFO TOO LONG
CAUSE A QLLU containing an information field that is
too long was received.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-23 through MESSAGE INTERNAL ERROR
-26
CAUSE An internal error has occurred.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-27 through MESSAGE (reserved for internal use only)
-49
CAUSE An internal error has occurred.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------
-50 through MESSAGE INTERNAL ERROR
-100
CAUSE An internal error has occurred.
ACTION Call your Hewlett-Packard support contact.
--------------------------------------------------------------------------